Air Pro-Plus
Contents
1. a The system has three different Power unit has NO alarm signals identified by power feed Mains Failure illumination sequences A BC Press for at least two seconds to lock the Control Unit settings a beep sounds and the amber LED illuminates to indicate system is locked When locked only the Alarm Mute and Lock Unlock buttons remain operational Press again for at least two seconds to unlock beep sounds and amber LED turns off The Control Unit will automatically unlock in the event of a power failure TROUBLESHOOTING Symptoms Problems Cause Points to check Low Pressure The mattress is set to a mode that is Change the mode button from soft to a too SOFT The CPR has been knocked moved Check all tubing is not kinked within the mattress There may be a leak in the system Ensure that the tubing within the mattress constant basis firmer pressure setting as required If the mattress is still too soft after a short period of 10 minutes then please call an engineer Ensure CPR valve is closed are fully connected required Evaluate that the mattress to be of a less firm state after a short period of 10 minutes If this is not achieved then please follow the task as below before calling an engineer for assistance NB Check all tubing is not kinked within the mattress High Pressure The mattress is excessively firm on Set mattress to a softer setting as clinically a Telephone H2. QUICK REFERENCE GUIDE This is a quick reference guide for the Dyna Form Air Dyna Fo rm Pro Plus refer to user manual for additional information Ai r P ro p u S Product Code MAT PRO PLUS 200 85 16 O Static Lock SD Firm On Off Power Button The Power Button turns the system power on and off by pressing the Power Button for at least two seconds CPR Function Rapid deflation of the Mattress may be required for emergency treatment or to decommission CPR the system Firmly pull the Rapid Release CPR Tag from the side of the Mattress to rapidly o deflate the entire system To re inflate the system after the Rapid Release CPR Tag has been Valve removed replace as such ensuring all sealing connectors are firmly attached and restart the Control Unit Wait for the Mattress system to gain optimal pressure Perform a Bottoming Out test after inflating the mattress following rapid deflation Press buttons to increase or decrease pressure setting The Soft Medium amp Firm settings allow comfort to the user without clinical compromise Soft Soft Mode The GREEN LEDs illuminate to indicate which of the three settings is operational Medium Mode LED Mode Settings Press Dynamic Mode for alternative cells cyclically inflating and deflating Static Mode will automatically revert to Alternation Mode after one hour for patient safety Firm Mode Upon power up the system auto
3. elpline Service and Maintenance 0845 459 9831 Please document product code MAT PRO PLUS 200 85 16 and serial number on rear of the pump prior to calling Direct Healthcare Direct Healthcare Services Ltd Units 8 10 Withey Court Western Industrial Estate Caerphilly South Wales CF83 1BF UK Sales Office Tel 0845 459 9831 Fax 0845 459 9832 E info direct healthcare org uk W www directhealthcareservices co uk
4. matically reverts back to the dynamic mode operating at the previous pressure setting for patient safety Static Mode will automatically revert to Alternation Mode after one hour for patient safety Dynamic Dynamic Mode Press to facilitate Static Mode for clinical procedure patient transfer purposes After 20 minutes the system automatically reverts back to the previous pressure setting for patient safety Press Static Mode for all cells to be fully inflated with no dynamic alternation Static Mode will automatically revert to Alternation Mode after one hour for patient safety D Static Static Mode NB Please ensure that all securing straps on the base of the mattress are secured onto the NON MOVING PARTS of the bed frame Alarm Mode Lockable Mode LED Mode Settings S Silences the audible alarm on off Audible alarm will resume after 20 minutes if cause of failure not resolved Display Alarm Function Alarm Function AN The system cannot reach T the set pressure within 8 The Red Alarm LED A B or C ee minutes l flashes and an audible alert sounds A Bc The pressure is to HIGH to indicate the control unit or mattress pressure has failed The LED will The system cannot reach remain illuminated until appropriate a the set pressure within 8 pressure is restored The audible eee minutes alarm can be silenced by pressing A Bc The pressure is to LOW the Alarm Mute button
Download Pdf Manuals
Related Search