GT15 Fingerprint Unit User`s Manual
Contents
1. this unit to the GOT fit it to the connection interface of the GOT and tighten the mounting screws in the specified torque range Undertightening can cause a drop failure or malfunction Overtightening can cause a drop failure or malfunction due to screw or unit damage WIRING PRECAUTIONS lt gt DANGER Be sure to shut off all phases of the external power supply used by the system before wiring Failure to do so may result in an electric shock product damage or malfunctions CAUTION Exercise care to avoid foreign matter such as chips and wire offcuts entering the unit Not doing so can cause a fire failure or malfunction Make sure to securely connect the cable to the connector of unit Incorrect connection may cause malfunctions STARTUP AND MAINTENANCE PRECAUTIONS lt gt DANGER Before starting cleaning always shut off GOT power externally in all phases Not doing so can cause a unit failure or malfunction Undertightening can cause the GOT to drop short circuit or malfunction Overtightening can cause a short circuit or malfunction due to the damage of the screws or unit Do not disassemble or modify the unit Doing so can cause a failure malfunction injury or fire Do not touch the conductive areas and electronic parts of this unit directly Doing so can cause a unit malfunction or failure 2 Through the cable in the installation hole of the control panel and then install t2. 0 Xin Chang Road Shanghai 200003 China Tel 86 21 6120 0808 Taiwan Setsuyo Enterprise Co Ltd 6F No 105 Wu Kung 3rd Rd Wu Ku Hsiang Taipei Hsine Taiwan Tel 886 2 2299 2499 Korea Mitsubishi Electric Automation Korea Co Ltd 1480 6 Gayang dong Gangseo ku Seoul 157 200 Korea Tel 82 2 3660 9552 Singapore Mitsubishi Electric Asia Pte Ltd 307 Alexandra Road 05 01 02 Mitsubishi Electric Building Singapore 159943 Tel 65 6470 2460 Thailand Mitsubishi Electric Automation Thailand Co Ltd Bang Chan Industrial Estate No 111 Moo 4 Serithai Rd T Kannayao A Kannayao Bangkok 10230 Thailand Tel 66 2 517 1326 Indonesia P T Autoteknindo Sumber Makmur Muara Karang Selatan Block A Utara No 1 Kav No 11 Kawasan Industri Pergudangan Jakarta Utara 14440 P O Box 5045 Jakarta 11050 Indonesia Tel 62 21 6630833 India Messung Systems Pvt Ltd Electronic Sadan NO III Unit No15 M 1 D C Bhosari Pune 411026 India Tel 91 20 2712 3130 Australia Mitsubishi Electric Australia Pty Ltd 348 Victoria Road Rydalmere N S W 2116 Australia Tel 61 2 9684 7777 A MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN NAGOYA WORKS 1 14 YADA MINAMI 5 CHOME HIGASHI KU NAGOYA JAPAN When exported from Japan this manual does not require application to the Ministry of Economy Trade and Industry for service transaction permission Specifi
3. AUTIONS CAUTION Dispose of this product as industrial waste TRANSPORTATION PRECAUTIONS CAUTION Make sure to transport the GOT main unit and or relevant unit s in the manner they will not be exposed to the impact exceeding the impact resistance described in the general specifications of this manual and GT16 User s Manual or GT15 User s Manual as they are precision devices Failure to do so may cause the unit to fail Check if the unit operates correctly after transportation 1 OVERVIEW This User s Manual describes GT15 fingerprint unit hereinafter referred to as the fingerprint unit This unit distinguishes the fingerprint of the user who registered by connecting it with GT16 or GT15 and can limit other users operations 2 SPECIFICATIONS Manuals The following shows manuals relevant to this product Detailed Manual Manual number Manual name Model code GT16 User s Manual SH 080778ENG Sold separately 1D7M88 GT15 User s Manual SH 080528ENG Sold separately 1D7M23 GOT1000 Series Connection Manual 1 3 to 3 3 SH 080532ENG Sold separately 1D7M26 GT Designer2 Version2 Screen Design Manual For GOT1000 Series 1 3 to 3 3 Sold separately SH 080530ENG 1D7M25 Relevant Manuals For relevant manuals refer to the PDF manuals stored in the GT Designer2 CD ROM 2008 MITSUBISHI ELECTRIC CORPO
4. MITSUBISHI GT15 Fingerprint Unit User s Manual GT15 80FPA Thank you for purchasing the GOT1000 Series Prior to use please read both this manual and detailed manual thoroughly to fully understand the product MODEL GT15M 80FPA U MODEL CODE 1D7M91 IB NA 0800439 B 0901 MEE GRAPHIC OPERATION TERMINAL GOTio900 SAFETY PRECAUTIONS Always read these precautions before using this equipment Before using this product please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly The precautions given in this manual are concerned with this prod uct In this manual the safety precautions are ranked as DANGER and CAUTION Indicates that incorrect handling may cause O DANGER hazardous conditions resulting in death or severe injury Indicates that incorrect handling may cause A CAUTION hazardous conditions resulting in medium or slight personal injury or physical damage Note that the A CAUTION level may lead to a serious accident according to the circumstances Always follow the precautions of both levels because they are impor tant to personal safety Please save this manual to make it accessible when required and always forward it to the end user 4 INSTALLATION PROCEDURE 4 1 Before Installation To install the fingerprint unit on the contro
5. ONS 5 a 71 8 5 2 g g g a S 3 S ij i a R 5 3 a 7 g 8 ve vac gt 6 0 24 ae J 64 2 52 8 371 46 S 49 1 93 Description Decorative cover that is attached to the upper side of the fingerprint unit 2 Installation fitting Fixing the fingerprint unit 1 Cover For 12 Part to put a finger for recognizing a fingerprint Connection cable for the RS 232 interface of the GOT Connected to the unit 3 Fingerprint reader 4 Cable 0 6m Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties Z For safe use This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi This product has been manufactured under strict quality control However when installing the product where major accidents or losses coul
6. RATION Packing List After unpacking the box check that the following products are included Model Product Quantity Fingerprint unit 1 Cover For 12 GT16 80FPA Double sided tape Spare Cable clamp hl rm ala Installation fitting 5 PRECAUTIONS FOR USE 1 The fingerprint unit complies with the protective structure IP4X The unit cannot be used with wet fingers or oil fingers The protective structure of the fingerprint unit differs from that of the GOT IP67 When using the GOT do not use with wet fingers or oil fingers 2 Do not pull the cable Doing so can cause malfunction or failure of the module 3 The fingerprint unit is a consumable product Check the unit for scratch damage or dirt at regular intervals and replace with new one if necessary 4 To be recognized as a fingerprint put the finger including fingertip on the fingerprint reader firmly with covering the reader as shown in the following figure Press the finger including fingertip on the fingerprint Put the finger on the fingerprint reader reader firmly H Br covering the reader 5 The following shows corrective actions when the fingerprint unit operates incorrectly Corrective actions When the Dry finger Moisten the finger with breath fingerprint is ry ting and put the finger again Troubles Causes registered the fingerprint reader does not ight brightly Dirty fin
7. cations subject to change without notice Printed in Japan
8. d occur if the product fails install appropriate backup or failsafe functions in the system Country Region Sales office Tel U S A Mitsubishi Electric Automation Inc 500 Corporate Woods Parkway Vernon Hills IL 60061 U S A Tel 1 847 478 2100 Brazil MELCO TEC Rep Com e Assessoria Tecnica Ltda Rua Correia Dias 184 Edificio Paraiso Trade Center 8 andar Paraiso Sao Paulo SP Brazil Tel 55 11 5908 8331 Germany Mitsubishi Electric Europe B V German Branch Gothaer Strasse 8 D 40880 Ratingen GERMANY Tel 49 2102 486 0 U K Mitsubishi Electric Europe B V UK Branch Travellers Lane Hatfield Hertfordshire AL10 8XB U K Tel 44 1707 276100 Italy Mitsubishi Electric Europe B V Italian Branch Centro Dir Colleoni Pal Perseo Ingr 2 Via Paracelso 12 l 20041 Agrate Brianza Milano Italy Tel 39 039 60531 Spain Mitsubishi Electric Europe B V Spanish Branch Carretera de Rubi 76 80 E 08190 Sant Cugat del Valles Barcelona Spain Tel 34 93 565 3131 France Mitsubishi Electric Europe B V French Branch 25 Boulevard des Bouvets F 92741 Nanterre Cedex France TEL 33 1 5568 5568 South Africa Circuit Breaker Industries Ltd Private Bag 2016 ZA 1600 Isando South Africa Tel 27 11 928 2000 Hong Kong Mitsubishi Electric Automation Hong Kong Ltd 10th Floor Manulife Tower 169 Electric Road North Point Hong Kong Tel 852 2887 8870 China Mitsubishi Electric Automation Shanghai Ltd 4 F Zhi Fu Plazz No 8
9. ger even when the finger is put on the reader Remove stains and put the finger again When the The finger is not Press the finger on the fingerprint is put on firmly fingerprint reader firmly registered the fingerprint gs Change the registered finger to reader remains Thin finger the middle finger or first finger it brightly When the fingerprint is recognized the fingerprintis not recognized by the fingerprint reader unless the finger is put on the reader a number of times The unclear fingerprint Change the registered image is fingerprint registered 2 1 General Specifications The general specifications of the fingerprint unit are the same as those of the GOT except the following three items Refer to GT16 User s Manual or GT15 User s Manual for the general specifications of the GOT Item Specifications Operating ambient temperature Operating ambient humidity 10 to 85 RH non condensing Storage ambient humidity 10 to 85 RH non condensing 0 to 40 C 2 2 Performance Specifications Items Specifications External light 5000Lx or less Protective structure IP4X Internal current consumption 5 0VDC Weight 0 28kg 0 62Ib 0 22A The general specifications and performance specifications of the fingerprint unit shown above differ from those of the GOT Use the fingerprint unit in the above environment 3 PART NAMES AND EXTERNAL DIMENSI
10. he fingerprint unit Fingerprint unit Control panel Installation hole 3 Place the mounting fixtures on the mounting fixture attaching part of the fingerprint unit and fix them by tightening the mounting screws in the torque range of 0 36 to 0 48 N m Magnified figure 4 Attach the cover to the fingerprint unit Attach the cover as required Position the tabs of the cover to the holes of the upper side of the unit Paste the unit on the control panel using the double sided tape without spaces between the unit and the panel 5 Connect the cable to the RS 232 interface of the GOT 6 To eliminate the looseness of the wiring bundle it with cable clamps Cable clamp POINT Set to ON by 5V supply at Communication settings of the utility CAUTION Always secure the cables connected to the unit e g run them in conduits or clamp them Not doing so can cause unit or cable damage due to dangling moved or accidentally pulled cables or can cause a malfunction due to a cable contact fault Do not hold the cable part when unplugging any cable connected to the unit Doing so can cause unit or cable damage or a malfunction due to a cable contact fault Always make sure to touch the grounded metal to discharge the electricity charged in the body etc before touching the unit Failure to do so may cause a failure or malfunctions of the unit DISPOSAL PREC
11. l panel make installation holes on the control panel with the dimensions shown below The space of 10mm is required above and below the hole respectively for the installation fittings Installation hole of GOT ki hole of fingerprint unit sooi o 4 76 17 0 67 50 21 978 A 42 1 65 Panel thickness 2 to 4 mm or less GOT A mm inch B mm inch GT1695 383 5 15 1 282 5 11 12 GT1595 2 0 08 0 0 2 0 08 0 0 GT 1685 302 11 89 228 8 98 671585 2 0 08 0 0 2 0 08 0 0 GT1675 289 11 38 200 7 87 GT157I 2 0 08 0 0 2 0 08 0 0 GT1665 227 8 94 176 6 93 GT156 2 0 08 0 0 2 0 08 0 0 153 6 02 121 5 2 0 08 0 0 2 0 08 0 0 GT155 Unit mm inch 4 2 Precautions for Installation 1 To make installation holes on the control panel remove the GOT from the control panel 2 The recommended position to install the fingerprint unit is the right side of the GOT For right hand With the exception the fingerprint unit can be installed by making the installation hole of the unit on the left side of the GOT For left hand For the installation do not give stress including an incorrect bending radius of the cable on the connection cable 3 Install the fingerprint unit with a distance of 3mm or more around the GOT A distance of 17mm or more is requi
12. red between the installation hole of the GOT and that of the fingerprint unit When the fingerprint unit is used with other extension units the fingerprint unit cannot be installed in some areas because the cables of the other extension units contact the fingerprint unit For prohibited areas when using other extension units refer to GT16 User s Manual or GT15 User s Manual 4 3 Unit Installation The following shows how to install the fingerprint unit on GT1685 as an example 1 Turn off the GOT Install the fingerprint unit in a installation hole for the control panel DESIGN PRECAUTIONS CAUTION Do not bunch the control wires or communication cables with the main circuit or power wires or lay them close to each other As a guide separate the lines by a distance of at least 100 mm 3 94 inch Otherwise malfunctions may occur due to noise INSTALLATION PRECAUTIONS lt gt DANGER Be sure to shut off all phases of the external power supply used by the system before mounting or removing this unit to from the GOT Not doing so can cause a unit failure or malfunction A CAUTION Use this unit in the environment given in the general specifications of this manual and GT16 User s Manual or GT15 User s Manual Not doing so can cause an electric shock fire malfunction or product damage or deterioration Do not drop the unit or subject it to string shock A unit damage may result When installing
Download Pdf Manuals
Related Search