AIR / MANUAL BOTTLE JACK USER`S MANUAL MODEL 69120B
Contents
1. vET NOD eseg 30 BC ee Buu o ee Mes 19005 20 pb ____ 86 t ____ Bury deusjzef l 90 _ _____ duung 25 _ 1O LE IN GO ob Buryjooudisng 96 ASS AUEL IIO OET L ____ 5 290009 70 pb E _____ ff pS _____ ASSyesoH iv get i PSMA 20 D Es TA sin PS PUYJAD und 10 AO yed ALO uond19S ALO uondI19S LIMITED ONE YEAR WARRANTY Jackco Transnational Inc warrants all Jackco equipment and tools to the original purchaser against any manufacturing defect in material or workmanship for a period of one 1 year from the original date of purchase If the defective equipment tool is determined to be covered under this warranty it shall be repaired or replaced at manufacturer s discretion without charge provided that the equipment or tool must be returned with proof of purchase to the dealer and freight prepaid if returned to the manufacturer This warranty shall not apply to damage due to accident negligent use and lack of maintenance abuse or applications other than the specific function the equipment or tool is designed for No other warranties expressed or implied including those of merchantability or fitness for particular purpose shall be applicable to2. ACKCO MODEL 69120B AIR MANUAL BOTTLE JACK 20TON CAPACITY USER S MANUAL c JE _ JOUE 0 En gs ih Go Transna tional Inc 2012 South El Monte CA 888 452 2526 www jackco com FOR YOUR SAFETY Read all instructions warnings and cautions carefully Follow all safety precautions to avoid personal injury or property damage during system operation Jackco cannot be responsible for damage or injury resulting from unsafe product use lack of maintenance or incorrect product and or system operation Contact when in doubt as to the safety precautions and operations Failure to comply with the following cautions and warnings could cause equipment damage and personal injury Stay clear of loads supported by hydraulics A cylinder when used as a load lifting device should never be used as a load holding device After the load had been raised or lowered it must always be blocked mechanically Do not exceed equipment rating never attempt to lift a load weighing more than the capacity of the cylinder Overloading causes equipment failure and possible personal injury The cylinders are designed for a maximum pressure of 10 000 psi Do not connect a jack or cylinder to a pump with a higher pressure rating The system operating pressure must not exceed the pressure rating of the lowest rated component in the system
3. Contact your equipment dealer service center pump Ram will not lower Release valve circuit defective Contact your equipment dealer service center UTTER Model 69120B Parts List C E KE 92 _____ ____ __ EA TEST Guru deus sz 2 _____ oyseguoiANigz ________ 5 OST i 19ND OL vz ____ 92 _____ _____ el ______ ____ buwofzz pb 1 ______ Zr 295 OMNUS LZ _ __ 22 __________ meos ded 92005 oz pb Guru deus L UOIS d 11V 64 Ex 02 meng onen wees yr 2 Buro el oseoj Sunds enen Kajes er onen A 21 Z Buds 89 was SAIBA 0925 2 UO OF ______ Cun XH 29 _______ Ley aseg 0 819 91 JOUSE A 0 mais 19005 pesH ssid 99 Guru deus o f 1 ___ ________ BSE vb CET Surofs 62 eusem _________ Cds l IN Xe COTE pb 1684 29 gef l pb ____ 19 ____ st 1981S 60 l 0
4. Jackco except as specifically stated herein In no event shall Jackco be liable to any party for any special direct indirect consequential punitive damage of any nature caused by the sale or use of the equipment or tool Note This warranty gives the original purchaser specific legal rights which may very from state to state Jackco Transnational Inc 2012 South El Monte CA 888 452 2526 www jackco com
5. Install pressure gauges in the system to monitor operating pressure It is your window to what is happening in the system BE SURE SETUP IS STABLE BEFORE LIFTING LOAD Cylinders should be placed on a flat surface that can support the load Where applicable use a cylinder base for added Stability Do not weld or otherwise modify the cylinder to attach a base or other support e Avoid situations where loads are not directly centered on the cylinder plunger Off center loads produce considerable strain on cylinders and plungers In addition the load may slip or fall causing potentially dangerous results Immediately replace worn or damaged parts genuine JACKCO parts Standard grade parts will break causing personal injury and property damage JACKCO parts are designed to fit properly and withstand high loads To avoid personal injury keep hands and feet away from cylinder and work piece during operation NEVER set the relief valve to a higher pressure than the maximum rated pressure of the pump Higher settings may result in equipment damage and or personal injury Do no remove relief valve Keep hydraulic equipment away from flames and heat Excessive heat will soften packing and seals resulting in fluid leaks Heat also weakens hose materials and packings For optimum performance do not expose equipment to temperatures of 150 F or higher Protect hoses and cylinders from weld spatter Hydraulic equipme
6. nt must only be serviced by a qualified hydraulic technician For repair service contact your equipment dealer service center To protect your warranty use only JACKCO hydraulic oil Specifications Lifting Capacity Min Height Max Height Shipping Weight Working Pressure 18 7 inch 39 6 Lbs 18kg 101 145 psi Inspection Prior to each use visually inspect for leaking hydraulic oil damaged loose or missing parts If jack is worn or damaged remove from service and contact your equipment dealer service center for repair Maintanence Check oil level With the jack in an upright position and the ram completely retracted open the release valve turn counter clockwise and remove the filler plug The oil level should be just up to the hole Fill if necessary with clean hydraulic jack oil Lubricate internal components With the release valve open manually pump the handle several times Purge the hydraulic system of air During transit the unit may become air bound causing a spongy ram action To purge the system close the release valve turn clockwise Manually pump the jack to full height Open the release valve and push down on the ram Repeat these steps if necessaty to completely purge the system Keep the jack clean Occasionally lubricate the handle socket pivot point extension screw release screw thread and air valve to prevent corrosion Operation 1 Jack operation is contolled either manually or by external air
7. pressure Either insert the handle into the handle socket to manually operate or connect to an external air pressure source clean connections prior to assembly 2 To raise the jack turn the release valve clockwise until tight and either manually pump with the provided handle or while connected to an air supply depress the air valve 3 To lower the jack turn the release valve counter clockwise slightly and very slowly Be careful not to turn the release valve too quickly or more than two full rotations otherwise dangerous sudden lowering may occur Trouble Shooting Problem Solution Air pump will not operate Low air pressure Keep air pressure between 101 145 psi Air outlet is frozen Stop using and thaw frozen outlet Lack of lubrication Supply oil to air valve Air pump acts but ram Release valve is open Close valve clockwise won t rise Lack of hydraulic oil Add hydraulic oil e Air bound system See maintenance Ram will not rise to Lack of hydraulic oil Add hydraulic oil highest position e Release valve not fully closed e Close valve clockwise Ram lowers slowly e Outlet valve dirty or defective Contact your equipment dealer service center Air pump packing defective Ram rises slowly Filter is filled with dirt Contact your equipment dealer service center Air pump packing defective e Release valve not fully closed Oil blowing from air Air pump packing defective
Download Pdf Manuals
Related Search