LID571 Pocket Reader
Contents
1. EID Aalten b v reserves the rights to change specifications without prior notice 19 a a User manual LID571 Pocket Reader 4 FAQs Question Nothing happens the LID571 Pocket Reader is dead What is wrong Answer There are three possibilities 1 There is no battery installed place a 9V battery in the LID570 Pocket Reader alkaline or rechargeable NiMH 2 The battery is inserted in the wrong way check the and 3 The battery is completely flat Replace the battery or recharge the battery Question Why does the LID571 Pocket Reader constantly give the SAME ID message Answer The checkbox Read only new ID in the general settings tab sheet is checked Question Why doesn t the LID571 Pocket Reader read as well as it did before Answer This can be caused by several reasons 1 The battery is almost flat Replace the battery or recharge it for maximum performance There is a lot of noise in the air See if the LID571 Pocket Reader will read better in another place no PC monitors for example 3 If possible remove any metal close to the LID571 Pocket Reader or transponder Question Why doesn t the LID571 Pocket Reader communicate or give an error message and stops communication Answer This can be caused by several reasons 1 TheLID571 Pocket Reader is not in communication mode Put it in the IR mode by pressing the red pushbutton twice quickly The LID571 Pocket Reader should beep twice and display Comports act2. ID number specify if you want to wedge the ID number Date and Time specify if you want to wedge a date time stamp Use Suffix specify the keys that must be wedged after the ID code date time stamp is wedged use the keyboard button Ts 3 Blocks Flex i 5 Blocks Flex 317 7 Blocks Flex 80 PSK1 fos ISO FDX B 04 Fecava 420 Trovan Unique 01 64 bits ASK EID Aalten b v reserves the rights to change NT specifications without prior notice 9 User manual LID571 Pocket Reader when clicking the keyboard button the following screen is shown Control characters 01 02 03 04 05 06 07 08 09 OA OB OC OD OE OF LSB 00 NUL SOH STX ETX EOT ENG ACK Bell BS TAB LF VT FF CR so SI RS DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM Keyboard F5 F6 F7 F8 F9 FIO F11 2 Som Backspace Insert Tab Del Caps Lock Shift Ctrl Alt Automatic Wedging utility TAB Specify the string by clicking the control keyboard characters in this screen or simply enter text in the textbox below When done click the Done key Example Prefix Automatic Wedging utility Tab key Type from table see page 11 ID Date and Time Suffix Tab key end Enter key The result when reading 4 tags in Microsoft word is Automatic Wedging utility Trovan 0000962D53 27 5 2003 11 03 04 end Automatic Wedging utility Trovan 000113066C 27 5 20
3. Print table Use custom ID codes This option enables the use of custom name assignment Custom codes in reader Displays the number of custom codes present in the LID571 Pocket Reader Send ID code via Com Sends the ID code via infrared Send Custom code via Com Sends the custom name via infrared Load custom codes from reader Use this button to download the custom codes from the LID571 Pocket Reader Save custom codes to reader Will upload the custom names to the LID571 Pocket Reader Clear reader Clears all records from the reader including the historical memory Load table from file A complete list of transponder codes and custom names can be loaded from file Only unknown ID codes will be added to the table Save table to file The codes present in the table can be saved to file Clear custom codes from table This option deletes the filtered codes from the table This does not affect the data stored in the LID571 Pocket Reader Print table Print the table to the selected printer EID Aalten b v reserves the rights to change specifications without prior notice 15 a a User manual LID571 Pocket Reader Search topic Can be used to filter the records Select a search topic and enter the search string in the Search on box EID Aalten b v reserves the rights to change specifications without prior notice 16 User manual LID571 Pocket Reader To add custom codes there are two possibilities 1
4. Read all ID codes All transponders are read saved and sent if these options are enabled Read only new ID The same transponder can not be read until another transponder is read Even a complete shut off will not affect this option Send ID over Comport This option sends the transponder code to another infrared device Send delay This is the delay between reading and sending the transponder code via infrared This delay can be adjusted between 0 and 25 seconds Communication mode delay The LID571 Pocket Reader will shut off when there was no communication during this period between 5 and 1275 seconds Shut down delay This is the time whereafter the reader will power off when the red pushbutton is released after a successful or failed readattempt Use buzzer The buzzer can be turned on to indicate successful readattempts Otherwise the buzzer will only sound in case of errors or when the LID571 Pocket Reader is turned into Communication or Setup mode EID Aalten b v reserves the rights to change specifications without prior notice 11 n x User manual LID571 Pocket Reader Use LCD backlight The LCD backlight can be turned on or off to save the battery The backlight is not used when the reader is in the communication mode Password There will be no password request at start up when the password is empty EID Aalten b v reserves the rights to change specifications witho
5. CONNECT IT TO A COMPORT 1 Connect the infrared to RS232 converter to your PC 2 Putthe reader in the communication mode by double clicking the trigger button and put it within communication distance of the converter Be sure there is nothing standing between the two infrared devices and that the infrared devices are aimed towards each other Start the PC program whereafter communication should be established If there was an error message please try again or go to 5 Go to SYSTEM in the CONTROL PANEL of Windows 95 98 Check if the serial comport is installed properly If there are any problems with the serial comport please delete it and restart the PC The serial comport will then be installed automatically Start up the PC software again and try to communicate If there is still no communication go to 6 6 Goto SYSTEM in the CONTROL PANEL of Windows 95 98 and check if the comports are set as follows address 02F8 02FF and interrupt 3 otherwise address 03F8 03FF and interrupt 4 Now restart your PC and try to start the PC software again tnis en not if the infrared port is connected to a virtual comport EID Aalten b v reserves the rights to change specifications without prior notice 7 User manual LID571 Pocket Reader 3 3 Starting the software Put the LID571 Pocket Reader into the communication mode by double clicking it s red pushbutton The message Comports active appears on the readers display Sele
6. The latest software can also be downloaded from our website www eid aalten nl Software on disks 1 2 EH 4 Insert the floppy disk labelled ONE in your disk drive From the START menu select RUN Enter the following text ANSETUP EXE and press ENTER Follow the instructions on your screen Software on CD 1 Insert the CD in your CD ROM device The CD will start automatically If not open index htm from the CD 2 Select Install LID571 PC software Windows 98 NT 2000 XP 3 Follow the instructions on your screen EID Aalten b v reserves the rights to change specifications without prior notice 6 User manual LID571 Pocket Reader 3 2 How to establish communication The LID571 Pocket Reader is able to communicate with a PC through an infrared connection and a direct connection using a RS232 cable in two different ways Some PC s especially Laptops can communicate with their integrated infrared port while others have to use an infrared to RS232 serial communication device 3 2 1 Using an infrared to RS232 serial communication converter An infrared to RS232 converter changes RS232 signals into infrared signals Three types of converters are compliant with our LID571 Pocket Reader which are the SmartBeam the Jet Eye and the IR mate These can also be ordered at your dealer s office DO NOT USE THE INSTALLATION SOFTWARE DELIVERED WITH THE DEVICE DO NOT CONFIGURE THE DEVICE AS INFRARED PORT JUST
7. is to low a longer beep signal will be heard and a low battery message will be shown on the LC display The specifications of the LID571 Pocket Reader are General data Reading distance p to 45 mm ID100 best direction Weight Incl 9V battery Standard LC Display with backlight or extra memory approx 00 codes without date time stamp approx 6350 wit date time stamp ABS UL 94 HB Displayed data ID code or custom name assignment max 16 characters No code and firmware version If no tag could be detected Low battery message Replace or charge the battery Memory full message Historical memory is full Same ID message The Read only new ID option is enabled and the same tag is read The reader will not save the ID into the historical memory and continues scanning can vary due to environmental conditions like interference of PC monitors etc EID Aalten b v reserves the rights to change m specifications without prior notice 3 User manual LID571 Pocket Reader 3 Using the SOFT57X PC software The LID571 Pocket Reader is delivered with Windows 9x ME XP 2000 NT4 PC software as standard The software is designed to interface between the LID571 Pocket Reader and the PC This allows the user to easily communicate with the reader 3 1 How to install the software With the LID571 Pocket Reader you should receive the PC software on floppy disks or CD
8. the IR210B infrared adapter and at a maximum angle of 15 degrees trovan unique transponders These transponders have an unique identificationcode which can not be altered These transponders are also called RO transponders Read only transponders can be read by every LID571 Pocket Reader trovan FLEX transponders The data inside these transponders can be altered with any information up to 15 characters long These transponders are also called RW transponders Read write transponders can be read by every LID571 Pocket Reader trovan FLEX transponders using 3 5 or 7 blocks can be read Send delay This is the delay between reading and sending the transponder code via infrared This delay can be adjusted between 0 and 25 seconds You must hold down the scanning button after a successful reading to allow your pocket reader to send the ID code For instance if you have set the send delay at 10 seconds you must hold down the scanning button for 10 seconds After this time the reader will send the ID code and shows a message on the display ID SENT OVER COM Note if you set the send delay to zero seconds the reader will send the ID code immediately after a successful reading without showing any message on the display Historical memory The transpondercodes which are read can be saved in the LID571 Pocket Readers internal memory This memory is called the historical memory The maximum number of codes which can be saved in the LID571 P
9. 03 11 03 50 end EID Aalten b v reserves the rights to change specifications without prior notice 10 a User manual LID571 Pocket Reader 3 4 2 General settings screen The general settings of the LID571 Pocket Reader can be adjusted in the general settings tabsheet Connected reader L571 708i Programmed by Remco Nijenhuis Sjoerd Hakstege trovan Electronic identification systems 3 LID57X settings program SOFT57X 503 Bl x History codes Custom codes General settings Memo database Memory status Reading list Options Read all ID codes v Read Trovan Unique transponders C v Read ISO FDX B transponders Read only new ID Read Trovan Flex transponders Read PSK1 transponders lv Use LCD backlight Read PSK2 transponders Iv Read Fecava transponders Read 64 bits ASK transponders v Send ID to the PC after o sec Communication mode delay fiso sec General controls gt Get current settings amp Reset reader 4 Select comport E Action on receive ID Use buzzer Shut down delay gt Apply new setting ISO format Decimal Hexadecimal Change password Show on Status Bar Authorisation level gt Old password New password Verify new password Ready Reading list Select the transponder types you would like to read To maximise the readers performance it is advisable only to enable the transponder types you want to read
10. Download the saved codes to the history table and copy them to the custom table see page 13 Now you can edit the records in de custom table and send them to the reader 2 Click the button in the Custom Codes tabsheet The following screen is shown Custom record Manual input When pushing this button the reader will automatically turn to the reading mode for a certain period of time If a transponder is detected within this time the reader will send its ID number If no transponder is detected the reader will automatically return to the communication made EID Aalten b v reserves the rights to change specifications without prior notice 17 1 Now simply click the Get from reader button The reader will turn to the scanning mode and scans for a tag If one is detected all the settings are transferred the PC program without send delay If you are using an IR adapter make sure the reader is pointed to the adapter when scanning a tag Otherwise follow point 3 Only the custom name has to be typed to complete the record Now hit the OK button 2 One can also Choose the right transponder type from the drop down box enter the ID number and assign a custom name Now click the Ok button RN TE Scan a tag and send it to the PC by holding down the trigger button after a successful read The reader will send the ID code regarding the send delay Only the custom name has to be typed to complete t
11. RS232 cable the reader is turned on via a hardware circuit If the reader was not in off mode at the moment of the cable plug in the reader seems to hang up Please remove the cable and plug in again To avoid this kind of error 1 Do not remove the cable while the program is running or 2 Wait until the reader is off before you plug in again or 3 Putthe reader in Communication mode manually before you press the Connect button on your PC this way you can start scanning without removing the RS232 cable Tip you can set the send delay to 0 seconds to send the ID code directly after a successful read EID Aalten b v reserves the rights to change m specifications without prior notice 20 User manual LID571 Pocket Reader 5 Tips and Tricks Adding transponder codes in the custom name table Manual input When a transponder code has been read it can be added directly to the custom table To do this select the transponder code field in the custom table Now read a transponder and send the code directly to the PC The transponder code will be placed in the field automatically Auto input Just push the Get from reader button the reader will automatically turn into scanning mode and scans for a transponder if one is found the ID code will be sent to the PC If no tag was found within the scanning time the reader will return to the communication mode Copying codes from the historical memory to the custom table To copy the
12. USER MANUAL twovan LID571 Pocket Reader READ THIS MANUAL FIRST DATE 16 of March 2004 User manual LID571 Pocket Reader Contents page 1 Description of terms 3 2 Using the LID571 Pocket Reader 5 3 Using the SOFT57X PC software 6 3 14 How to install the PC Software 6 3 2 Howto establish communication 7 3 2 2 Using an infrared to RS232 serial communication converter 7 3 3 Starting the software 8 3 4 PC Software main screen 9 3 4 1 General controls panel 9 3 4 2 General settings screen 11 3 4 3 History codes screen 12 3 4 4 Customer name assignment screen 13 3 4 5 Memory status screen 15 3 4 6 Memo database screen 16 4 Frequently Asked Questions 17 5 Tips and tricks 18 Copyright EID Aalten B V Nijverheidsweg 28 5559 7122 AB Aalten A The Netherlands CE Tel 31 543 477119 Fax 31 543 475355 E mail info eid aalten nl Homepage http www eid aalten nl EID Aalten b v reserves the rights to change specifications without prior notice 2 User manual LID571 Pocket Reader 1 Description of terms LID571Pocket Reader The complete unit which can read and display the transponder code As standard the LID571 Pocket Reader can communicate with another device via a wireless infrared connection InfraRed communication A wireless communication method which can be used to transfer data from one device to another The device is able to communicate at distances of min 1 meter away from
13. a beep will be heard Now you only have to follow the instructions on de readers display The upper line shows the transponder type You have 5 seconds a counter is visible to push the button in order to enable the shown transponder type If the button isn t pushed within these 5 seconds the shown transponder will be disabled until the next time this menu is entered At the end of the menu the reader will turn off and apply the new settings Communication mode delay The reader will shut off when there was no communication during this period between 5 and 1275 seconds Power off time This is the time whereafter the reader will power off when the red pushbutton is released after a successful or failed read attempt EID Aalten b v reserves the rights to change m specifications without prior notice 3 User manual LID571 Pocket Reader Custom name assignment When a transponder code is read the LID571 Pocket Reader can display a name up to 16 characters instead of the transponder code This name can be the same for a batch of transponders This means that the transponder codes are still unique but the custom names could be the same When no custom name has been assigned to a transponder code the normal transponder code is displayed When custom name assignment is selected and a transponder is read the custom name will be displayed and or sent via infrared depending on the settings in the general settings tabsheet Custom names can no
14. ct LID57XV4xx In the windows Start menu to start the PC software When the screen below appears select the comport where the infrared device is connected and press the CONNECT button NOTE When using a RS232 cable the reader can be put into the communication mode automatically The reader will stay in the communication mode as long as the program is connected to the reader To be able to scan and send ID codes to the PC one has to put the reader in the communication mode double click before pressing the CONNECT button Select comport Please check all 3 options an retry EID Aalten b v reserves the rights to change specifications without prior notice 8 m m User manual LID571 Pocket Reader 3 4 PC Software main screen The main screen of the program is divided into four tabsheets 1 General settings The general settings of the LID571 Pocket Reader can be adjusted in this tab sheet 2 Reader memory Transponder codes that are saved in the historical memory can be downloaded from the LID571 Pocket Reader saved to file or deleted 3 Custom codes This tab sheet allows the user to assign custom names to transponder codes 4 Memory status Only version 403 and higher This tab sheet allows the user to analyse the readers memory 3 4 1 General Controls panel General controls Get current settings button Downloads all the settings of the reader and the number of saved codes Reset reader button Resets the reader to is i
15. ect comport Action on r m aj Search topic Cont None C Type C Code C Memo History table C RUM Edit memo Show on Status Bar Animal Elephant Name Denis Date of birth may 16 1993 NS In the upper half of the screen a table is visible this table contains all the transponders which have a memo field When selecting one record single click the matching memo field is displayed in the lower half of the screen Now the memo field can be edited and saved When looking for a specific record the user can filter the table in five different ways 1 Read a tag and send it to the PC send ID option must be enabled see page 12 The record of the tag will be selected regardless of the option which is selected in the Action on receive ID box Note New records will only be generated if a unknown code is received and the option Show tag s memo field in the Action on receive ID box is selected 2 Select Type as a search topic and specify the transponder type The table will now show the records which meet the conditions 3 Select Code as a search topic and enter a text in the box on the right 4 Select Memo as a search topic and enter a text in the box the table will show the records which have the specified string in their matching memo field 5 Select History table as a search topic the table will show the records which are also present in the history table See page 14
16. he record Now hit the OK button User manual LID571 Pocket Reader 3 4 5 Memory status This screen allows the user to analyse the reader s memory Click the Analyse memory button to analyse the memory The memory will now be analysed When done a chart is shown with the current memory status Example S LID57X settings program SOFT57X 503 Connected reader L571 708i GB x History codes Custom codes Memo database guck ls ienes ee Sjoerd Hakstege General settings Memory status B 512 bytes reserved memory B 3085 bytes 395 custom record s Electronic identification systems B 1790 bytes 179 history record s Oo 21381 bytes free memory General controls ur Action on receive ID Show on Status Bar m Loading data s EID Aalten b v reserves the rights to change specifications without prior notice 18 a User manual LID571 Pocket Reader 3 4 6 Memo database This screen allows the user to edit the memo fields which are stored in the database RJ LIDS7X settings program SOFT57X 503 Connected reader L571 708i iof X General settings Memory status E tue EN ele Sioerd Hakstege History codes Custom codes Memo database Memo database Electronic identification svstems Trovan Unique 00002D181A Trovan Unique 0000840C43 Trovan Unique 00008433C2 000113066C 84 bits ASK 0F01B84D6F General controls BR Get current settings Reset reader xci Sel
17. ing in the box Specify if the string has to match from the beginning or anywhere in the record EID Aalten b v reserves the rights to change specifications without prior notice 14 a User manual LID571 Pocket Reader 3 4 4 Customer name assignment This tab sheet allows you to assign a custom name to a read only transponder code This means that instead of the read only transponder code the custom name will be displayed on the LC display The custom code tab sheet is shown below To edit ID codes and Custom names select a record and double click To add or delete a record use the navigator under the dbase grid RJ LIDS7X settings program SOFT57X 503 Connected reader L571 708i Programmed by Remco Nijenhuis Sioerd Hakstege General settings Memory status History codes Custom codes Memo database Custom code options v Use custom ID codes Custom codes in reader C SendlD code via COM Send custom code via COM Electronic identification svstems General controls 1 Trovan Unique 000113066C Every tag can 2 Trovan Unique 0000840C43 have a custom 3 Trovan Unique 00008433C2 name up to 5 Trovan Unique 00002D181A __ 16 characters IE EI I Action on receive ID Search topic TP Moe r Code C Name ontains Show on Status Bar C Begins with Controls Bt Load codes from reader Bb Save codes to reader Load codes from file Save table to file Clear table it Clear Reader
18. is option also displays date and time on the readers LCD Codes in reader Displays the number of saved codes in the readers historical memory Load codes from reader Downloads all saved codes from the LID571 ISO Multi Readers historical memory Load codes from file A complete list of transponder codes can be loaded from file The file is added to the present codes in the table Clear table Deletes the filtered codes from the table This does not affect data stored in the LID571 ISO Multi Readers historical memory Clear codes from reader This option clears the LID570 Pocket Readers historical memory Copy to custom table Copies the present codes from the history table directly to the custom table Double codes and read write codes are not copied to the custom table Copy to memo table Copies the present codes from the history table directly to the memo table Double codes and read write codes are not copied to the custom table If there are custom names assigned these names will be copied into the empty memo field Save table to file The user can save the historical memory to file Print table Prints the table to the selected printer EID Aalten b v reserves the rights to change specifications without prior notice 13 User manual LID571 Pocket Reader Search topic Can be used to filter the records Select a search topic and enter the search str
19. ive Now try again 2 TheLID571 Pocket Reader is outside the maximum communication distance of 1 metre approx 3 feet or it is not aimed towards the infrared port of the PC 3 The battery is flat Did you get the LOW BATTERY message 4 Is the infrared communication port on the PC installed properly If you are using an infrared to RS232 adapter do NOT install any drivers for this device If communication doesn t start contact your dealer for more information Question Why does the LID571 Pocket Reader turn off after a few minutes Answer This is done to save the battery The communication mode delay can be adjusted in the general setting tab Question The LID571 Pocket Reader beeps in a different way Why Answer This is an indication of one of the following 1 TheLID571 Pocket Reader beeps longer than normal The battery is almost flat 2 The LID571 Pocket Reader beeps continuously The LID571 Pocket Readers has entered the message mode read the message on the display and continue by pushing the red button e MEMORY FULL historical memory is full Just erase the historical memory or stop storing the codes in the historical memory use the PC program to change these settings e HARDWARE FAILURE something is wrong contact your dealer Question Why does the LID571 Reader seems to hang up if I plug in the RS232 cable Answer Probably the reader was set into communication mode automatically this means that once you plug in the
20. nitial values also deletes all saved codes Select comport button Re select the comport Exit Hide button Depends on the Action on receive ID settings Action on receive ID box The selected option will be executed when receiving an ID code The option Send ID in the General setting tabsheet Use Pop Up Screen for must be selected see page 12 seconds Action on receive ID there are 4 different options e show on status bar the ID code will be shown on the bottom left of the screen e show tag s memo field every ID code can have it s own Memo field to add extra data like addresses or service dates for maintenance purposes This data is stored in a database and will not be erased after the program is closed e Use Pop up Screen The read code is shown in a Pop up screen This screen is closed automatically after the specified time but can also be closed manually e Use WEDGE settings This PC software has a integrated wedging utility With this option one can easily wedge the received data into any windows application for example notepad The settings can be edited by clicking the button which will appear next to the dropdown box when selecting this option The following screen will be shown Use Prefix specify the keys that PETES must be wedged before the ID zm E ERA code is wedged use the Soe Convert table keyboard button s eivin Type specify if you want to wedge the transponder type
21. ocket Readers historical memory is dependent of the internal memory size the number of custom names which are assigned and whether the codes are saved with or without the date time stamp When the saving option is selected the transponder will be saved in the historical memory When custom name assignment is selected the transponder code is saved instead of the custom name Date Time stamp The readers date and time are added to the transponder code when it is saved in the historical memory The reader will display the date and time during scanning mode when this function is activated Communication mode In this mode the LID571 Pocket Reader can communicate with another infrared device like a laptop computer or an infrared adapter The reader can be put into the IR mode by pressing the trigger button twice in short succession double clicking The LC display will show COMPORTS ACTIVE The reader will exit Communication mode when the trigger button is pressed once or it will automatically turn off if no communication has occurred after a certain adjustable time Communication mode delay Setup mode When entering the setup mode you must choose which transponders you would like to read This can also be done with the PC software The reader can be put into this mode by double clicking the red button just like entering the communication mode but now you have to hold down the button after the second click for aprox 5 seconds After this time
22. t be assigned to trovan FLEX transponders The following diagram shows a summary of how to enter the different states in which the LID571 Pocket Reader can be Reader is off Push red button Beep Hold down button for at least 0 3 sec to enter the scanning mode The reader starts to scan for tags Release button within 0 3 sec Don t push button within the next 300 ms Reader does nothing Push button witin the next 0 3 sec Long beep message COMPORTS ACTIVE Release button after the long beep The reader enters the communication mode in wich data and settings can be transferred to from a PC Hold down button after the long beep and wait for the next beep then folow the instructions on the display EID Aalten b v reserves the rights to change specifications without prior notice 4 User manual LID571 Pocket Reader 2 Using the LID571 Pocket Reader The LID571 Pocket Reader has been developed to read all trovan read only transponders and the 3 5 or 7 blocks read write transponders Only use 9V alkaline or rechargeable NiMH batieries type PP3 After the battery is installed pressing and holding the red trigger button will activate the LID571 Pocket Reader The backlight will be turned on and the message SCANNING will show on the LC Display If a tag is read the D number or customer name assignment will be displayed and an acoustic signal will be heard If the battery voltage
23. transponder codes in the LID571 Pocket Readers historical memory to the custom name table you should follow steps 1 4 Ts 2 EID Aalten b v reserves the rights to change Download the transponder codes from the LID571 Pocket Readers memory Use the Copy to custom table button to copy the codes from the LID571 Pocket Readers memory table to the custom table Only read only ID codes will be copied Go to the custom code tab sheet and change the custom names There will be no double ID codes in the custom table Save the custom codes to the LID570 Pocket Reader the historical data will be lost or to a file specifications without prior notice 21
24. ut prior notice 12 a User manual LID571 Pocket Reader 3 4 3 History codes screen The transponder codes that are read can also be saved in the readers internal memory The reader memory tab sheet shown below will allow you to read and delete the saved codes from the LID571 Pocket Reader and to save them to a file or print them J LID5S X settings program SOFT57X 503 General settings History codes Connected reader L571 708i Programmed by Remco Nijenhuis Sjoerd Hakstege n n systems Memory status Custom codes Memo database Reader memory options Codes in reader ja Electronic identificatio M Savecodes V Save codes with date time General controls Filename History ID Type Code Custom name 38 Trovan Unique 39 7 Blocks Flex 40 ISO FDX B Animal 00008433C2 AAAAAAAAAAAAAAA 985 100005480718 64 bits ASK 0F01B84D6F Search topic None C Type C Code C Date C Time H Load codes from reader B Load codes from file E Clear table T Clear codes from reader Action on receive ID Contains C Begins with Show on Status Bar be Controls E Copy to custom table D Copy to memo table Ej Save table to file Save codes This option saves the transponder codes in the LID571 ISO Multi Readers historical memory With date time This option adds date and time to the codes in the LID571 ISO Multi Readers historical memory Th
Download Pdf Manuals
Related Search