Home

Instruction manual thermostat - A

1. THERMOSTAT Instruction manual W A touch About this manual Thank you for choosing A TOUCH solutions The first chapters of this manual will show you how to configure your unit to operate correctly with your climatization system Later you will learn how to operate it on a daily basis At the end you will have a chapter about integration with your A TOUCH automation system if this is the case The A TOUCH thermostat is a programmable thermostat where you can schedule different temperatures for different periods of each day of the week both for winter and summer time The thermostat can also be included in any scenario and its keyboards can also be used for light and shutter control when integrated in an automation system The thermostat at a hint D ma a gt S G eco mooo 4 HA touch CE Yas Ref 880 0023 Made in Thailand u 230V 50Hz 5A total bs V a N On off key or Back key in menu Up key OLED display Down key Ventilation key Menu key or Enter in menu Programming key Reset key Programming key Test key info a touch in th www a touch in th W A touch The A TOUCH thermostat is a unit that the following basic features selectable cycle for summer cooling and winter heating programmable temperature schedule independent for winter and summer temperature scheduling with 3 ON pe
2. Now change with key UP or DOWN Confirm by pressing key ENTER MAXIMUM the display jumps to the next MENU item MAXIMUM TEMPERATURE If the thermostat is ON even during OFF periods the unit will check the room temperature if it is higher than the maximum temperature setting and assuming the thermostat is in SUMMER mode it will switch on the cooling to make sure the house is below this temperature If the thermostat is OFF time is displayed then the minimum or maximum temperature do not work To adjust the maximum temperature proceed as follows TEMPERATURE Press key ENTER the display shows the actual maximum temperature Now change with key UP or DOWN info a touch in th www a touch in th W A touch Confirm by pressing key ENTER the display jumps to the next MENU item ADJUST DATE AND TIME The thermostat needs a clock so that the schedule may run If the units are interconnected with the bus then adjusting time in one unit adjusts the time on all the units of the house The time will remain equal on all the units of the house In fact the unit where you adjust the time will be the master of the clock in all the house To adjust the date and time proceed as follows ADJUST Press key ENTER the display shows the actual date and you can adjust the year Now change with key UP or DOWN Confirm by pressing key ENTER now you can adjust the month N
3. 22 If you want to switch the unit ON again just press key STBY the unit goes back to ON mode and the program settings are reloaded e N ps Ko If the unit has the SCHEDULE function ON then it operates automatically according to the schedule defined switching the climatization on and off according to the needs You can always switch it on or off independently of the schedule Notes In OFF mode the unit does not control minimum and maximum temperatures In AUTO OFF mode the unit controls minimum and maximum temperature These settings are indepent of the week day ADJUSTING THE TEMPERATURE You can adjust the target temperature when the unit is in ON mode no matter if it is in manual or automatic mode The new setting will be automatically stored in the memory If the unit is in an ON period the new setting is stored in the program of that day and that moment If periods overlap and more than one period are active in the info a touch in th www a touch in th W A touch moment you change the temperature then the new temperature is stored in all active periods regardless of if they were different or not To adjust the temperature proceed as follows 16 41 229 21 20 Press the key UP to increase the temperature the target temperature is shown temporarly on the big display and then goes back to the normal display Press the key DOWN if you want to decrease the temperature the t
4. 1 multi touch key all 4 keys together To switch between Thermostat mode and Automation mode proceed as follows Hold the keys UP and VENT pressed together for more than 5 seconds on the thermostat panel you will hear 2 short BEEPs on the panel the display layout changes to Automation mode Now you can use the keys of the thermostat for automation info a touch in th www a touch in th W A touch If you need to temporarily operate the thermostat proceed as follows g Press the keys UP and VENT together briefly the display layout changes to thermostat mode for 5 seconds You can now operate the keys of the thermostat Every press renews the 5 seconds timeout When you are finished just leave it and the mode goes back to Automation To put back the panel in Thermostat mode proceed the same way you will hear 2 BEEPs on the panel and the display layout changes back to the thermostat layout info a touch in th www a touch in th
5. COOLER units SELECT UNIT Press key ENTER the display shows the actual unit Change with key UP or DOWN SELECT IT REMOTE Confirm by pressing key ENTER SELECT UNIT COOLER Proceed the same way for the COOLER unit When you confirm with key ENTER the display will show the next SELECT UNIT TYP menu item UNIT TYPE The thermostat must be configured for the climatization unit it is connected to because the operation is different for several types of climatization units You can choose the following unit types RADIATOR usually wall or floor mounted radiators with water operation with on off of valve R FLOOR radiating floor with water proportional operation AIRFLOW2 air flow unit with 2 tubes on off of valve and 3 ventilation speeds AIRFLOW4 air flow unit with 4 tubes on off of heat and cool valves and 2 ventilation speeds with automatic change between Winter and Summer operation AIR CON1 air conditioning on off of compressor and 3 ventilation speeds DAIKINFD DAIKIN air conditioning of series FDX equipped with interface board KRP413A AIR CON2 air conditioning on off of compressor and 3 ventilation speeds but with delay of 3 minutes to start the compressor To select the right unit type proceed as follows SELECT Press key ENTER the display shows the actual unit Change with key UP or DOWN INGO NG Confirm by pressing key ENTER een the display shows the time a
6. EMOTE TO ALOCAL UNIT To associate a remote unit with a local unit proceed as follows Press the key PROG on the remote unit to put it in programming mode Vly tt Mee the 3 LEDs go ON Press now the key STBY on the touch panel of the local unit 00o the 3 LEDs on the remote unit go OFF From this moment on the units are associated Notes The remote unit can only be associated with 1 local unit SELECTING THE UNIT TYPE IN THE REMOTE UNIT The remote unit must also be configured for the correct unit type it is connected to To select it proceed as follows Hold the key PROG on the remote unit for more than 1 second gt Kee the red LED blinks the number of times as the selected mode 1 radiator 2 radiating floor 3 airflow2 4 airflow4 5 air conditioning 6 Daikin FDX a Press the key PROG to select the next value woe the red LED follows the selected type Confirm by pressing the key TEST the LED goes off OPERATION The thermostat will operate normally and according to the settings in HEATER unit and COOLER unit With the local unit if LOCAL With the remote unit if REMOTE With both units if BOTH No operation if NONE The operation is the same if the unit operates with a local remote or both units info a touch in th www a touch in th W A touch SWITCHING THE SECOND UNIT ON AND OFF If the heater or cooler unit selected is LOCAL or REMOTE operation w
7. ER UNIT It is possible that one single thermostat panel controls 2 different climatization machines In that case one actuator controls for example the radiating floor and another actuator controls for example the air conditioning The unit defined as LOCAL is the actuator that is connected to the thermostat panel the other unit is then the REMOTE actuator The REMOTE unit has to be programmed to operate as SLAVE of the LOCAL unit Please see the chapter USING 2 UNITS WITH 1 THERMOSTAT for more details info a touch in th www a touch in th W A touch If for example the LOCAL unit controls a radiating floor the HEATER UNIT should be LOCAL if you wish to heat only with it You can choose to heat with the air conditioning if you select REMOTE or even BOTH if you want both to heat at the same time The same applies for the COOLING UNIT In our example cooling would be made with the air conditioning Therefore the COOLING UNIT should be set to REMOTE This setting can be changed any time you like If for example you have no cooling unit then set it to NONE the thermostat will not operate in Summer mode Puting temporarily both units operating together can be made without setting the HEATER or COOLER units to BOTH just hold the key VENT on the normal operation that the second unit will switch on together with the first Please see the chapter USING 2 UNITS WITH 1 THERMOSTAT for more details This is how you select the HEATER and
8. OFF to AUTO OFF and switch from AUTO OFF to ON OFF DOWN switch from ON to AUTO OFF and switch from AUTO OFF to OFF TIMER should not be used DELAY switch from ON to AUTO OFF and switch from AUTO OFF to OFF after the delay time specified SCENARIO select directly the mode as defined in the SCENARIO Notes If unit is totally OFF TOGGLE will not be able to switch the uit ON only AUTO OFF If the unit is AUTO OFF TOGGLE will not be able to switch the unit completely OFF TIMER has no meaning because the maximum time that can be set is 20 minutes too less for climatization operation The SCENARIO command is transformed into OFF DOWN when all members of the scenario are already on the scenario state In this case the thermostat will switch from ON to AUTO OFF or AUTO OFF to OFF depending on the original state In any case the climatization is switched on info a touch in th www a touch in th W A touch The SCENARIO will select directly the mode as defined for the scenario regardless of its starting mode You cannot change the temperature or the ventilation speed with a remote key Associating a key to the thermostat The programming follows exactly the same rules as programming keys and outputs on the automation system Please refer for the Home Automation User Manual for more details To control the thermostat with an automation key proceed as follows Press the key PROG on the thermostat you will h
9. arget temperature is shown temporarly on the big display and then goes back to the normal display VENTILATION SPEED The unit types AIRFLOW2 AIRFLOW4 AIR CON1 AIR CON2 and DAIKINFD have ventilation and their speed is controlled by the thermostat When you switch on the thermostat the ventilation speed is always set to automatic In this mode the ventilation speed depends on the difference between the target temperature and the room temperature the higher the difference the higher the ventilation speed You can choose a certain ventilation speed However if you do it then the speed will remain as you specified regardless of the difference between target and room temperature manual mode To change the ventilation speed proceed as follows Press the key VENT to select the next speed v2 220 the new speed is shown on the top left corner The AIRFLOW4 unit type only has 2 speeds all others have 3 speeds The transition between one speed and the next has a pause of about 1 second This is necessary to avoid relay damage in some kinds of ventilators info a touch in th www a touch in th W A touch USING 2 UNITS WITH 1 THERMOSTAT As explained above it is possible to use one thermostat to control 2 different climatization units So that this is possible the slave actuator REMOTE must be associated with the master actuator LOCAL that is the unit that is connected with the thermostat panel ASSOCIATING A R
10. ation key BACK key UP key DOWN key ENTER info a touch in th www a touch in th W A touch SCHEDULE You may define a temperature schedule for the unit to operate automatically However you can switch this schedule off without having to clear it for example when you go on vacation SCHEDULE Press key ENTER the display shows the actual mode SGEEGUIE Now change with key UP or DOWN Confirm by pressing key ENTER the display jumps to the next MENU item CYCLE The thermostat may be used in the WINTER for HEATING and in the SUMMER for COOLING This menu allows selecting the correct mode SELECT Press key ENTER the display shows the actual mode Now change with key UP or DOWN CYCLE Confirm by pressing key ENTER the display jumps to the next MENU item Probably you will need to adjust this setting twice a year MINIMUM TEMPERATURE If the thermostat is ON even during OFF periods the unit will check the room temperature if it is lower than the minimum temperature setting and assuming the thermostat is in WINTER mode it will switch on the heating to make sure the house is above this temperature If the thermostat is OFF time is displayed then the minimum or maximum temperature do not work To adjust the minimum temperature proceed as follows TEMPERATURE Press key ENTER ager ae the display shows the actual minimum temperature
11. ation periods can overlap each other In that case in winter mode the highest temperature will prevail In summer mode the lowest temperature prevails To define the program for winter operation proceed as follows PROGRAM Press key ENTER the display shows the week day Monday You can select another ESTs day if you like by pressing key UP or DOWN info a touch in th www a touch in th W A touch Confirm by pressing key ENTER 06 00H20 now you can adjust the starting hours of the first period Change with key UP or DOWN Confirm by pressing key ENTER now you can adjust the finishing hours of the first period Change with key UP or DOWN a Confirm by pressing key ENTER 06 09H22 now you can adjust the temperature of the first period DSTART Change with key UP or DOWN ORPA Confirm by pressing key ENTER now you can adjust the starting hours of the second period Repeat the same procedure for periods 2 and 3 Once you confirm the temperature of the third period you go to the week day Tuesday menu TUESDAY the display shows the week day Tuesday You can select another day if you like by pressing key UP or DOWN COPY Confirm by pressing key ENTER EDIT now you can choose between copying the previous week day settings or edit this day To edit this day press key DOWN 00 00H20 the display shows EDIT Now press key ENTER 5 me
12. ear one BEEP on the panel Now press the key on the automation panel you will hear a long BEEP from this moment on the thermostat will react to that key If the key you used is configured to send the command SCENARIO you must now store the unit s operation mode for the scenario Put the thermostat in the mode you want it to be in the scenario Now hold the SCENARIO key for more than 5 seconds you will hear a long BEEP on the panel the scenario is stored USING THE THERMOSTAT KEYS TO CONTROL AUTOMATION OUTPUTS If the thermostat is programmed to operate according to the schedule you defined then you will need very little or even no interaction with it as it always operates automatically In this case you can decide to use the keys of the thermostat to do something else for example switch lights on and off or control shutters or curtains The thermostat panel can operate in Thermostat mode default operation but also in Automation mode where all the keys are normal automation keys no operation of the thermostat if they are not programmed to do it In Automation mode the panel has all the keys available 4 direct keys 2 horizontal sliding keys 2 vertical sliding keys 1 multi touch key all 4 keys together In Thermostat mode the panel has the 4 direct keys for the operation of the thermostat but the sliding and multi touch keys are still available 2 horizontal sliding keys 2 vertical sliding keys
13. ith just one unit it is possible to switch temporarily the mode to BOTH without changing the COOLER or HEATER unit in the configuration menu To switch the REMOTE unit on and off proceed as follows 22 Hold the key VENT for more than 1 second the REMOTE unit will switch on the actual ventilation speed is shown Notes The ventilation speed will always be shown even if the remote unit is not an air conditioning or an air flow unit this is because the local unit cannot know the configuration of the remote unit If the remote unit has no ventilation then changing the ventilation speed will have no effect If the remote unit has ventilation it will follow the same speed as indicated on the local unit display You can define any type of unit for the local and remote units gt any combination is possible INTEGRATION WITH DOMOTICS The A TOUCH thermostats can be integrated in a home automation system enabling association with scenarios remote switch on and off both from a light switch or your smart phone APP For that the unit has to be connected to the communication bus of the automation system CONTROL FROM AN AUTOMATION UNIT Any automation unit for example light switch can switch the thermostat on and off if they are associated and the right commands are sent The commands have the following function TOGGLE switching between OFF and AUTO OFF or switching between AUTO OFF and ON ON UP switch from
14. nd extis the menu Remember the 16 30 unit is OFF if the display shows time Notes info a touch in th www a touch in th W A touch There will be no damage if the unit is operated with the wrong unit type selected just you will not have the correct operation info a touch in th www a touch in th W A touch UNIT OPERATION SWITCHING ON AND OFF The thermostat has 4 modes OFF where the thermostat does not work at all schedule is OFF a N ite ZnO joerc AUTO OFF where the thermostat runs the program you defined but is a in an OFF period 16 29 220 AUTO ON where the thermostat runs the program you defined but is 21 20 in an ON period 16 29 220 MANUAL where the thermostat was manually switched ON in an OFF 20 38 period As you can see the display contents show the mode of the unit There is no difference between AUTO ON and MANUAL because in both modes the unit makes the same a N 212 In OFF mode the unit shows the time and temperature If the time is missing then the time field does not display To switch on press key STBY a N N N Zi Ze the display shows the actual temperature and the target temperature on the top right corner 16 35 220 When the target temperature is achieved the unit will switch the 22 0 heating off If you wish to switch off the unit even during the execution of the 22 00 program just press key STBY the unit goes OFF
15. ow change with key UP or DOWN Confirm by pressing key ENTER now you can adjust the day Now change with key UP or DOWN Confirm by pressing key ENTER now you can adjust the hours Now change with key UP or DOWN Confirm by pressing key ENTER now you can adjust the minutes Now change with key UP or DOWN Confirm by pressing key ENTER now you can adjust the time zone Now change with key UP or DOWN Confirm by pressing key ENTER the display jumps to the next MENU item 13 01 01 14 01 01 MONTH 14 01 01 14 04 01 14 04 01 14 04 13 HOURS aca m m gt D gt D gt a aI S m 3 a SoS z x lt HOUR ji OV fek 02 zZ gt EEN BRAE Oo PEREFECERER fam eee v2 as I z E m v MINUTES 1672 AONE mil PROGRAM The seconds are automatically cleared to zero when you confirm the time zone Ifthe time zone is then daylight saving time is not automatically adjusted If the time zone is not the time is automatically adjusted to Winter time last Sunday of October or Summer time last Sunday of March according to the time zone You can select by increasing or decreasing the time zone until one of the ends WINTER AND SUMMER PROGRAMS You can define 3 operation periods with different temperatures for each day of the week different for winter and summer operation These oper
16. riods for each day of the week programmable Minimum and Maximum temperature possibility to operate with different types of climatization units possibility to use it to drive 2 different climatization machines 1 thermostat for 2 actuators Some more features are available but they will be explained in the chapter Advanced Settings Configuration The unit allows a number of configurations so that it works as you wish These configurations need to be made only once The configurations are made in MENU mode The MENU can be accessed only if the unit is completely OFF if the display does not show the time or hold the key STBY for more than 1 second o the unit will switch off and the display will show the time 23 A The MENU is accessed by pressing then the key VENT The menu steps are SELECT SCHEDULE to select if the schedule should run or not SELECT CYQUE to adjust the thermostat for Winter or Summer operation TEMPERATURE MINIMUM to adjust the minimum temperature of the house TEMPERATURE MAXIMUM to adjust the maximum temperature of the house ADJUST DATE TIM to adjust date and time PROGRAM WINTER to define the winter program PROGRAM SUMMER to define the summer program SELECT UNIT HEATER to define the unit for heating SELECT UNIT COOLER to define the unit for cooling SELECT UNIT TYP to define the unit type In the menu mode the keys have the following oper
17. the display shows the settings for the first period The procedure is Memet pp as explained for Monday Once you confirm the temperature of the WEEK DAY third period the display shows the next week day Confirm by pressing key ENTER now you can choose between copying the previous week day settings or edit this day If you wish to copy just press key WEEK DAY ENTER the settings are copied and you can edit the next day Repeat the procedure for every week day When you reach Sunday and confirm the last setting then you will access the Summer Program menu The procedure is exactly the same as for the winter program STOP OS a FAQ STOP 06 09H20 TEMP i 06 09H20 COPY m m J S 2 2 m m 12 Ww iw i Notes If the starting hours of one period are the same as the stopping hours then the period does not work unit is off You can define one period as 0 to 24 hours this will work the whole day Periods can overlap in winter mode the highest temperature prevails in summer mode the lowest temperature prevails Itis not mandatory that you define all the operation periods for a certain day However in order for the program to be stored you must confirm all the 3 periods completely just keep the start and stop times equal and the period will not work When you finish defining the last week day of the summer period the HEATER display will show the next menu item SELECT HEATER AND COLL

Instruction manual thermostat - A

Contents

Download Pdf Manuals

Related Search

Related Contents