Operating and installation instructions 210514 - Andi
Contents
1. gt The current cooling temperature is indicated in the display 5 4 5 Shelves Moving or removing shelves The shelves have stops preventing them from being uninten tionally pulled out Lift the shelf slightly and pull forward a little Adjust the height of the shelf To do so push the cut outs along the supports In order to remove the shelf fully place it at a slant and pull out towards the front Re insert shelves at the required height The stops must face downwards and lie behind the front shelves Dismantling shelves The shelves can be disman tled for cleaning 10 X 5 4 6 Using the sectioned shelf Fig 13 Attach the support rails paying attention to the right R and left L part The glass plate 1 with pull out stops must be at the front so that the stops 3 face downwards 5 4 7 Door racks Moving the storage rack Remove storage rack according to illustration The boxes can be removed and placed on the table as a single unit Three small boxes are available through the customer service as optional equipment instead of one wide and one small box Either one or both the boxes can be used If particularly tall bottles are to be stored hang only a single box above the bottle rack Re positioning the boxes Lift them for removal and re position them as required Fig 14 Depending on model and options gt The door racks can be dism2. Operating and installation instructions Upright refrigerator with BioFresh compartment 210514 085340 01 SKBes4213 6 14 7 7 Eu r Appliance at a glance Contents 1 Appliance at a glance uuursnnunennnnnnonnnnennnnnennnnnenn 2 1 1 Description of appliance and equipmert 2 1 2 Range of appliance use uusnsnneneenenenneenennnne nennen 2 1 TEONOnm ee ee 3 1 4 External dimensions of the appliance 3 1 5 Saving energy uunnnessesennnnnennnnnnnnnnnnnnnnnnnnnnnnnennnnnnnennnn 3 1 6 FOomMeDRAldd nennnne nee A 2 General safety information uuuusennnannnennnn 4 3 Controls and displays uuuuunuaaneennnnnnnnnnnnnnnnnnnnnnn 5 3 1 Operating and control elements 5 3 2 Temperature display ccccccccccssceecseeeseeeeeeseeeeenees 5 4 Putting into operation uusuuenennannennnnnennnnnnnnnnnenn 5 4 1 Transporting the appliance cccecceesseeeeeseeeeeeeees 5 4 2 Installing the ADPlIANCE c cc eeceeseeeeeeeeeeeeeeeeeeeeees 5 4 3 Changing over the door hinges 44444 0 gt 6 4 4 Insertion into a row of kitchen units u 8 4 5 Disposing of PACkKAQGING cccccsseeeeeeeeeeeeeeeeeeenens 8 4 6 Connecting the appliance ccccccecseeeeeesseeeeeees 8 4 7 Switching on the appliance ccccssseeeeeeeeeeeeenees 8 5 COMME ON 2 een 8 5 1 Bright
3. ranging and sorting However do not leave cooled products there otherwise they may be pushed back or tipped over when the door is closed Do not store food too close together to enable good air circulation To safeguard bottles from tipping over move the bottle holder At the base of the refrigerator compartment the integrated bottle shelf or alternatively the glass shelf can be used To use the bottle shelf store the glass shelf compactly under the bottle shelf Place the bottles with the base pointing backwards facing the rear wall If the bottles project beyond the bottle shelf set the lower door rack one position higher S f 5 4 2 Setting the temperature The temperature depends on the following factors the frequency of opening the door the room temperature of the installation location the type temperature and quantity of the food The temperature can be set from 9 C to 3 C the recom mended temperature is 5 C For a higher temperature setting press Up button Fig 3 2 gt For a lower temperature setting press Down button Fig 3 3 gt When the button is pressed the first time the previously set value is indicated flashing in the temperature display To change the temperature in 1 C steps briefly press the button To change the temperature continuously hold down the button gt The value is displayed flashing during the setting operation
4. to the front of the kitchen unit by 34 mm at the side and by 50 mm in the middle of the appliance It can be opened and closed perfectly as a result Fig 11 Ventilation requirements Atthe back of the stack cabinet there has to be a ventilation duct of at least 50 mm depth throughout the width of the stack cabinet the larger the ventilation space the more energy saving the appliance is in operation If the appliance is installed with the hinges next to a wall Fig 17 4 the distance between appliance and wall has to be at least 40 mm This corresponds to the projection of the handle when the door is open 4 5 Disposing of packaging A WARNING Danger of suffocation due to packing material and plastic film gt Do not allow children to play with packing material The packaging is made of recyclable materials corrugated board cardboard expanded polystyrene parts polythene bags and sheets polypropylene straps nailed wooden frame with polyethylene panel Take the packaging material to an official collecting point oN 4 6 Connecting the appliance NOTICE Risk of damage to the electronic control system Do not use stand alone inverters conversion of d c to a c three phase or energy saving plugs A WARNING Fire and overheating hazard Do not use extension cables or multiple socket outlets The type of current alternating current and voltage at the installation site have
5. 2 Taking the appliance out of service Empty the appliance Pull out the power plug Clean the appliance see 6 1 Leave the door open to prevent odour 9 Disposing of the appliance The appliance contains some reusable materials and should be disposed of properly not simply with unsorted household refuse Appliances which are no longer needed must be disposed of in a professional and appropriate way in accordance with the current local regulations and laws When disposing of the appliance ensure that the refrigeration circuit is not damaged to prevent uncontrolled escape of the refrigerant it contains data on type plate and oil Disable the appliance Pull out the plug Cut through the connecting cable Depending on model and options Disposing of the appliance Depending on model and options 15 Liebherr Hausger te Ochsenhausen GmbH Memminger Strasse 77 79 88416 Ochsenhausen Deutschland www liebherr com
6. 4 Transferring the handle Fig 8 Lift the stopper Fig 8 30 out of the door bearing bush and transfer it gt Dismantle the door handle Fig 8 37 stoppers Fig 8 32 and pressure plates Fig 8 33 and transfer to the opposite side When fitting the pressure plates on the opposite side make sure they snap properly into place Depending on model and options Putting into operation 4 3 5 Fitting the door Place the door from above onto the lower bearing pin Fig 7 22 Close the door Insert the upper turn hinge Fig 6 72 in the door on the new hinge side gt Screw the upper turn hinge Fig 6 72 firmly into place with 4 Nm 2x Torx 25 Fig 6 73 Possibly make preliminary holes with a bradawl or use a cordless screwdriver Snap the cover Fig 6 70 and cover Fig 6 77 into place at the opposite side 4 3 6 Fitting the soft stop unit Fig 9 gt Remove the cover Fig 9 7 from the faceplate Fig 9 7 and re insert it at the other side gt Engage the soft stop unit with the joint pointing to the hinge side A and swivel into place B gt The screw holes at the left and right have to register gt Screw down the soft stop unit 2x Torx 15 Fig 9 6 Fig 10 Attach the faceplate Fig 70 7 to the soft stop bracket so that the catches face forwards and the front faces the appli ance gt Draw the soft stop bracket Fig 70 5 towards the bearing par
7. 7 from under neath and engage them in the holder Fig 78 2 at the front Depending on model and options 6 Maintenance 6 1 Cleaning the appliance A WARNING Risk of injury and damage as a result of hot steam Hot steam can lead to burns and can damage the surfaces Do not use any steam cleaners NOTICE Incorrect cleaning damages the appliance gt Do not use cleaning agents in concentrated form gt Do not use any scouring or abrasive sponges or steel wool Please do not use any aggressive scouring sand chloride chemical or acid based cleaning agents gt Do not use chemical solvents gt Do not damage or remove the type plate on the inside of the appliance It is important for the customer service Do not pull off bend or damage cables or other compo nents gt Do not allow any cleaning water to enter the drain channel ventilation grille or electrical parts Please use soft cleaning cloths and a universal pH neutral cleaning agent Please use cleaning and care products suitable for contact with foodstuffs in the appliance interior Empty appliance gt Pull out the power plug Clean plastic outer and inner surfaces with lukewarm water and a little washing up liquid Do not apply stainless steel cleaning agent to glass or plastic surfaces to prevent them from being scratched Darker areas at the beginning and quite an intensive colour of the stainless steel surface are norma
8. C upto 4 days Mussels at 2 C upto 6 days Tropical fruits at 6 C upto 15 days at0 C upto 20 days at 6 C upto 24 days Lemons at 6 C upto 45 days Limes at 6 C upto 55 days 5 5 5 Setting the temperature for BioFreshPlus gt The temperature for the BioFreshPlus compartment can be set separately on the control panel see Appliance at a glance a e ejr Fig 15 Setting for fish and seafood Press 2 C button Setting as normal BioFresh compartment Press 0 C button Setting for tropical fruits Press 6 C button Diz e Elco dsg 5 5 6 Adjusting the temperature in the BioFresh compartment The temperature is controlled automatically At a temperature in the refrigerator compartment of 5 C the temperature in the BioFresh compartment is between 0 C and 3 C You can adjust the temperature slightly colder or warmer The temperature is adjustable In the BioFresh compartment from bi coldest tempera ture to 69 warmest temperature In the BioFreshPlus compartment from ui coldest temperature to u3 warmest temperature The presetting is 65 uS With the bi ui bis b4 u4 values the temperature can drop below O C and therefore food can freeze slightly as a result Note for testing institutes If temperatures below 3 C are to be reached in the refrigerator compartment set the temperature in the BioFresh compartment to b1 b4 To
9. the fault yourself by refer ence to the list see Malfunction If this is not the case please contact the customer service whose address is given in the enclosed customer service list A WARNING Risk of injury if repair work is not carried out professionally gt Have any repairs and action not expressly specified on the appliance and mains cable carried out by service personnel only see Maintenance Read the appliance j a ALON VI Fig 19 1 service an EY No Fig 19 2 and i _ serial No Fig 19 3 oO off the type plate at eel Pe tll brent tt emir sree located inside the ara bo asda lg orn A appliance on the left hand side 4 Y 1z FI u H io M Sense TE Fig 19 Notify the customer service specifying the fault appliance designation Fig 79 7 service No Fig 79 2 and serial No Fig 19 3 gt This will help us to provide you with a faster and more accu rate service Keep the appliance closed until the customer service arrives gt The food will stay cool longer Pull out the mains plug not by pulling the connecting cable or switch off the fuse 7 Malfunction Your appliance is designed and manufactured for a long life span and reliable operation If a malfunction nonetheless occurs during operation check whether it is due to a handling error In this case you will have to be charged for the costs incurred even during the warran
10. to conform with the data on the type plate see Appliance at a glance The socket must be properly earthed and fused The tripping current for the fuse must be between 10 A and 16 A The socket must be easily accessible so that the appliance can be quickly disconnected from the supply in an emergency It must be outside the area of the rear of the appliance Check the electrical connection Plug in the power plug 4 7 Switching on the appliance Press On Off button Fig 3 6 gt The temperature display indicates the current temperature gt The interior light is on when the door is open gt If DEMO is displayed demo mode is activated Please contact the after sales service 5 Control 5 1 Brightness of the temperature display You can adjust the brightness of the temperature display to the light conditions of the room in which the appliance is installed 5 1 1 Adjusting the brightness The brightness is adjustable between h no illumination and hS maximum luminosity To activate the setting mode press SuperCool button Fig 3 7 for about 5s Depending on model and options gt The display indicates c gt The menu symbol Fig 3 4 shines gt Using the Up setting button Fig 3 2 and Down setting button Fig 3 3 select h To confirm briefly press the SuperCool button Fig 3 7 To set the display brighter press the Up setting button Fig 3 2 a To set the displ
11. activate the setting mode press the SuperCool button Fig 3 7 for about 5 s gt The menu symbol Fig 3 4 shines The temperature display indicates c Press the Up setting button Fig 3 2 the number of times required for b u to flash in the display To confirm briefly press the SuperCool button Fig 3 7 For a colder temperature adjustment press Down setting button Fig 3 3 12 To confirm press SuperCool button Fig 3 7 gt The temperature slowly adjusts to the new _ value it To deactivate the setting mode press the On Off button Fig 3 6 Of gt Wait for 5 minutes gt The temperature is indicated again in the temperature display 5 5 7 Setting the humidity in the HydroSafe is mN Fn 2 TS Low humidity move the regulator to the left gt ee n High humidity move the regu lator to the right Biorresh sate lak 5 5 8 Drawers Fig 16 Pull out the drawer lift it at the back and draw it forwards for removal Push the rails in again Fig 17 Pull out the rails gt Attach the drawer to the rails and push it in until it engages audibly at the back 5 5 9 Humidity control plate Fig 18 To remove the humidity control plate Having removed the drawers carefully draw the plate forwards and lower it for removal To insert the humidity control plate Insert the cover mould ings of the plate into the rear holder Fig 78
12. ainless steel side walls evenly wiping with the grain Subsequent cleaning becomes easier as a result gt Wipe side walls with a paint finish using a soft clean cloth only Putting into operation gt Remove all transit supports gt Dispose of packaging material see 4 5 Align the appliance so that it stands firmly and on a level by applying the accompanying spanner to the adjustable height feet A and using a spirit level Then support the door Extend the adjustable foot at the turn hinge B until it rests on the floor and then make a further 90 turn When a Side by Side appliance S is fitted together with a second appliance as a SBS combination Proceed according to the Side by Side combined fridge freezer installation instructions Accessories bag of the SBS freezer appliance with freezer compartment Note Clean the appliance see 6 1 If the appliance is installed in a very damp environment condensate may form on the outside of the appliance Always see to good ventilation at the installation site 4 3 Changing over the door hinges You can change over the door hinges if necessary NOTICE Risk of damage to side by side appliances due to condensa tion When a side by side appliance S is fitted together with a second appliance as a SBS combination the door hinges must remain as delivered gt Do not change over the door hinges Ensure that the following too
13. antled for cleaning 5 4 8 Removing the bottle holder Always take hold of the bottle holder on the plastic part 5 5 BioFresh compartment The BioFresh compartment allows some types of fresh food to be stored up to three times longer than in conventional refriger ators without compromising quality For food with an indicated best before date the date specified on the packaging always applies 5 5 1 HydroSafe The HydroSafe at the moist setting is suited for storing unwrapped salad vegetables and fruit with high inherent mois ture When the drawer is well filled a dewy climate with up to 90 humidity is established The humidity in the compartment depends on the moisture content of the food stored and on the opening frequency You can set the humidity yourself 5 5 2 BioFreshPlus compartment adjustable The adjustable BioFreshPlus compartment is suited for storing seafood fruit vegetables or tropical fruits depending on setting 5 5 3 Storing food Note Vegetables sensitive to cold such as cucumbers auber gines semi ripe tomatoes zucchinis and all tropical fruits sensitive to cold do not belong in the BioFresh compart ment Store citrus and tropical fruits in the BioFreshPlus compart ment at 6 C To prevent food spoilage due to transfer of germs Store unwrapped animal and vegetable products separate from one another in the drawers This also applies to different sorts of meat If food
14. appliance reaches the required temperature by itself If not please contact the after sales service see Maintenance The temperature is incorrectly set Set the temperature to a colder setting and check after 24 hours gt The appliance is too close to a source of heat stove heater etc Change the position of the appliance or the source of heat vV vVv vVv vV vi The interior light is not on The appliance is not switched on Switch on the appliance The door was open longer than 15 min 14 The interior light automatically switches off if the door has been open for about 15 min gt The LED illumination is defective or the cover is damaged A WARNING Risk of injury due to electric shock Live parts are located under the cover Have the LED interior light changed or repaired only by the customer service or by specialized personnel trained for the purpose A WARNING Danger of injury by LED lamp The light intensity of the LED illumination corresponds to laser class 1 1M If the cover is defective gt Do not look into the illumination with optical lenses from the immediate proximity This can cause injury to the eyes 8 Decommissioning 8 1 Switching off the appliance gt Press On Off button Fig 3 6 for approx 2 seconds gt The temperature display is dark gt If the appliance cannot be switched off the child lock function is active see 5 2 8
15. ay darker press the Down L setting button Fig 3 3 To confirm briefly press the SuperCool button Fig 3 7 gt The brightness is adjusted to the new value To deactivate the setting mode press the On Off button Fig 3 6 Or Wait for 5 minutes gt The temperature is indicated again in the temperature display 5 2 Child proofing The child proofing function enables you to make sure that the appliance is not inadvertently switched off by playing children rd 5 2 1 Setting the child lock function To activate the setting mode press SuperCool button Fig 3 7 for about 5 s gt The display indicates c gt The menu symbol Fig 3 4 shines gt Briefly press theSuperCool button Fig 3 7 to confirm When ci is indicated in the display to activate the child lock briefly press the SuperCool button Fig 3 7 gt The child lock symbol Fig 3 10 shines c flashes in the display When cd is indicated in the display to deactivate the child lock briefly press the SuperCool button Fig 3 7 gt The child lock symbol Fig 3 10 goes out c flashes in the display To deactivate the set up mode press On Off button Fig 3 6 Or Wait for 5 minutes gt The temperature is indicated again in the temperature display 5 3 Door alarm If the door is open for longer than 60 seconds the audible warning will sound The audible alarm is automatically silenced when t
16. gt The actual temperature is displayed about 5 s after the last press of a button The temperature slowly adjusts to the new value Control 5 4 3 SuperCool With SuperCool you switch to the highest cooling performance to reach lower cooling temperatures Use SuperCool to rapidly cool large amounts of food The SuperCool function uses slightly more energy Cooling with SuperCool gt Briefly press SuperCool button Fig 3 7 gt The SuperCool symbol Fig 3 72 lights up in the display gt The cooling temperature drops to the coldest value Super Cool is activated gt SuperCool is automatically deactivated after 6 to12 hours The appliance continues to operate in the energy saving normal mode To prematurely deactivate SuperCool Briefly press SuperCool button Fig 3 7 gt The SuperCool symbol Fig 3 72 goes out in the display gt SuperCool is deactivated 5 4 4 Holiday mode tn a aii The holiday mode saves energy and prevents odour from occurring when the door of the refrigerator compartment stays closed for a lengthy period Activating the holiday mode Remove all the food from the refrigerator and BioFresh compartment otherwise they sun will perish Press the holiday button Fig 3 T for 3 sec Hoi gt The holiday mode is activated The display indicates Ho Deactivating the holiday mode gt Briefly press the holiday button Fig 3 7 gt The holiday mode is deactivated
17. has to be stored together due to lack of space gt wrap the food 5 5 4 Storage times Control Standard values for storage time at low humidity Standard values or storage time at ow humidiy Note Please note that protein rich food deteriorates faster i e shellfish and crustaceans deteriorate faster than fish fish faster than meat Standard values for storage time at high humidity Vegetables salad Chicory days Lamb s lettuce days Peas days Kale days Carrots days Garlic days Kohlrabi days Lettuce days Herbs days Leek days Mushrooms days Radishes days Brussels sprouts upto 20 days Asparagus upto 18 days Spinach Savoy cabbage upto 20 days Apricots upto 13 Fruit days Apples Pears Blackberries Dates Strawberries Figs Blueberries Raspberries Currants Standard values for storage time at low humidity Butter upto 90 days Hard cheese upto 110 days Milk upto 12 days Sausage cold meat upto 9 days Poultry upto 6 days Pork upto 7 days Beef upto 7 days Sweet cherries Gooseberries Depending on model and options 11 Control Standard values for storage time at high humidity Additional standard values for storage time in the BioFreshPlus compartment Seafood Crab at 2
18. hat no food falls out Fig 6 gt Close the door Pull off the cover Fig 6 70 forwards and upwards Lift off the cover Fig 6 77 A CAUTION Risk of injury if the door tips Take good hold of the door Set down the door carefully gt Unscrew the upper turn hinge Fig 6 122x Torx 25 Fig 6 13 and raise it for removal Lift up the door and set it aside Depending on model and options 4 3 3 Changing the bearing parts Fig 7 Using the accompanying Allen key unscrew the threaded pin Fig 7 40 by about 1 turn Turn and lift out the bearing pin Fig 7 22 together with washer Fig 7 23 and adjustable height foot Fig 7 24 Lift off the stopper Fig 7 27 gt Unscrew the turn hinge Fig 7 25 gt Fully unscrew the threaded pin Fig 7 40 and screw it in on the opposite side at the turn hinge until it is flush outside with the turn hinge gt Unscrew the bearing element Fig 7 28 turn it through 180 and screw it firmly back into place gt Re insert the stopper Fig 7 27 into the other hole Carefully lift off the cover on the handle side Fig 7 27 and transfer it to the opposite side gt Screw the turn hinge Fig 7 25 firmly into place on the new hinge side possibly using a cordless screwdriver with 4 Nm Re insert the bearing pin Fig 7 22 together with washer and adjustable height foot Tighten the threaded pin Fig 7 40 4 3
19. he door is closed 5 3 1 Muting the door alarm The audible alarm can be muted when the door is open The sound switch off function is active as long as the door is left open Press alarm button Fig 3 8 gt The door alarm is silenced Depending on model and options Control 5 4 Refrigerator compartment The natural circulation of air in the refrigerator compartment results in zones differing in temperature It is coldest directly above the plate separating off the BioFreshPlus zone and at the rear wall It is warmest at the top front of the compartment and in the door 5 4 1 Food refrigeration Note The energy consumption increases and the cooling perform ance decreases if the ventilation is inadequate Always keep the air slits of the fan free Place butter and preserves in the upper area and in the door see Appliance at a glance Use recyclable plastic metal aluminium and glass containers and cling film for wrapping Always store liquids and food which is subject to odour or taste transfer in closed containers or cover them Foods which give off a large amount of ethylene gas and delicate foods such as fruit vegetables salad should always be stored separately or wrapped so as not to reduce the storage life e g do not store tomatoes together with kiwis or cabbage gt Use the front area of the refrigerator compartment floor only for briefly putting down cooled products e g when rear
20. ically when the Super Cool function is activated fresh food has just been placed in the appliance or the door has been left open for a while gt The sound is normal The ambient temperature is too high Solution see 1 2 A low hum The sound is produced by air flow noise of the fan gt The sound is normal Vibratory noise gt The appliance is not fixed to the ground The running of the cooling unit therefore makes objects and adjacent furniture vibrate gt Adjust appliance via the height adjustable feet gt Move bottles and containers apart Flow sound at the soft stop mechanism The noise is produced when the door is opened and closed p The sound is normal The temperature display indicates F to F3 There is a fault Please contact the after sales service see Maintenance DEMO shines in the temperature display The demo mode is activated Please contact the after sales service see Maintenance The outer surfaces of the appliance are warm The heat of the refrigeration circuit is used to prevent condensate from forming This is normal The temperature is not cold enough The door of the appliance is not properly closed Close the door of the appliance Insufficient ventilation Clear ventilation grilles The ambient temperature is too high Solution see 1 2 The appliance was opened too frequently or for too long Wait to see whether the
21. ilated Q In the event that the appliance is damaged contact the supplier immediately before connecting to the mains U The floor at the site must be flat and level Q Do not install the appliance in a location where it is exposed to direct radiation of the sun next to a cooker heater and similar U Always stand the appliance with its back directly to the wall Q The appliance may be moved only when it is empty Q Do not install the appliance without assistance CL The more R 600a refrigerant there is in the appliance the larger the room in which the appliance is standing needs to be In rooms that are too small a flammable mix of gas and air may be created if there is a leak According to the EN 378 standard every 11 g of R 600a refrigerant requires at least 1 m space in the room for the appliance The amount of refrigerant in your appliance is on the type plate inside the appliance gt Detach the connecting cable from the rear of the appliance removing the cable holder at the same time because other wise there will be vibratory noise Remove the protective film from the outside of the appli ance NOTICE The stainless steel doors are provided with a high quality surface coating and must not be treated using the accompa nying care product Otherwise the surface coating will be affected Zu Wipe the coated door surfaces using a soft clean cloth only Apply a stainless steel cleaner only to the st
22. l NOTICE The stainless steel doors are provided with a high quality surface coating and must not be treated using the accompa nying care product Otherwise the surface coating will be affected Zu Wipe the coated door surfaces using a soft clean cloth only In case of stubborn dirt use a little water or a neutral cleaning agent A microfibre cloth can be optionally used If the stainless steel side walls are dirty clean them using a commercially available stainless steel cleaning agent Then evenly apply the accompanying stainless steel care product making strokes in the direction of the grain gt Wipe side walls with a paint finish using a soft clean cloth only In case of stubborn dirt use a little water or a neutral cleaning agent A microfibre cloth can be optionally used Clean drain hole Remove deposits with a narrow instrument e g a cotton bud gt Most of the parts can be dismantled for cleaning see the relevant chapter Clean items of equipment by hand with lukewarm water and a little washing up liquid Only use a damp cloth to clean the telescopic rails The grease in the runners is for lubrication purposes and must not be removed Depending on model and options Maintenance After cleaning Wipe dry the appliance and items of equipment Connect the appliance and switch it on again Put the food back inside 6 2 Customer service First check whether you can correct
23. ls are to hand U Torx 25 CQ Torx 15 U Screwdriver Q Cordless screwdriver if necessary Q Second person for fitting work if needed U Accompanying Allen key size 2 4 3 1 Detaching the soft stop unit Fig 4 gt Open the door NOTICE Risk of damage If the door seal is damaged the door may fail to close properly and the cooling will be inadequate gt Do not damage the door seal with the screwdriver gt Disengage and remove the faceplate Fig 4 7 using a flat blade screwdriver gt The faceplate is attached over the soft stop bracket Slide the faceplate forwards over the soft stop bracket Fig 5 5 in the direction of the appliance Snap the safety lock Fig 5 3 into the oblong hole gt The safety lock prevents the hinge from snap closing Using a screwdriver lift off the cover Fig 5 2 from the outside and remove it in an outward direction If necessary tip the appliance backwards with the assis tance of a second person Press the pin Fig 5 4 out from underneath Press the soft stop bracket Fig 5 5 towards the door gt Remove the faceplate Fig 5 7 gt Unscrew the entire soft stop unit 2x Torx 15 Fig 5 6 Pull the soft stop unit out a little push it in the direction of the handle side and swing it out Set the soft stop unit aside 4 3 2 Detaching the door Note gt Remove any food from the door racks before removing the door so t
24. mption depends on the installation condi tions e g the ambient temperature see 1 2 Keep the time the appliance is open to a minimum The lower the temperature setting the higher the power consumption Store food logically see Appliance at a glance Ensure that all food is well packed and covered for storage This will prevent frost from forming Remove food as needed in order that it does not warm too much First cool warm food to room temperature before storing it Use the vacation function for longer vacation periods see 5 4 4 Accumulated dust increases the energy consumption Once a year dust the refrigerating unit together with the metal grille of the heat exchanger at the back of the appliance General safety information 1 6 HomeDialog Depending on model and options the Home Dialog system can be used to network a number of Liebherr appliances situated for example in the basement with a main appliance sited for example in the kitchen and control them via the latter You will find more information on the benefits requirements and principle of operation on the internet at www liebherr com Y 2 General safety information Danger for the user This appliance can be used by children of 8 years old and over and also by persons with restricted physical sensory or mental capacity or lack of experience and knowl edge if they are supervised or have been instructed on
25. ness of the temperature display 8 5 2 CHIC DFOOTM Gra eu nennen 9 98 OOF Alan reine 9 5 4 Refrigerator compartment 44snnn nennen 9 5 5 BioFresh compartment uu 4snn een nne nennen 11 6 MAIMtIENance aiaseeeeleiene 13 6 1 Cleaning the appliance u 4444404ee nennen een 13 6 2 Customer service annsesnsssneennnennennnnnnnnnennnnn nennen 13 7 MAM ENON siirsin iaaa 13 8 DecommissioniNd u u nme 14 8 1 Switching off the appliance 4440ne nen 14 8 2 Taking the appliance out Of service nunnennnennneeen 14 9 Disposing of the appliance uuuuuuseunnnnnnnneennnn 14 The manufacturer works constantly on the further development of all the types and models Therefore please understand that we have to reserve the right to make design equipment and technical modifications To get to know all the benefits of your new appliance please read the information contained in these instructions carefully The instructions apply to several models Differences may occur Text relating only to specific appliances is marked with an asterisk Instructions for action are marked with a the results of action are marked with a gt 1 Appliance at a glance 1 1 Description of appliance and equip ment Note Place food inside the appliance as shown in the diagram This allows the appliance to save energy during operation gt Shelves d
26. nism Fingers may be trapped when the door is closed Please observe the specific information in the other sections DANGER identifies a situation involving direct N danger which if not obviated may result in death or severe bodily injury WARNING _ identifies a dangerous situation which if not obviated may result in death or severe bodily injury CAUTION identifies a dangerous situation N which if not obviated may result in minor or medium bodily injury NOTICE identifies a dangerous situation which if not obviated may result in damage to property Depending on model and options Note Tidenttesusenintematonandtps AN 3 Controls and displays 3 1 Operating and control elements I FHL i A V Z c D X fA Holiday Up Down Ovo Superlool Alartr Fig 3 1 Holiday button 2 Up setting button 3 Down setting button 4 Menu symbol 5 Alarm symbol 6 On Off button 7 SuperCool button 8 Alarm button 9 Temperature display 10 Child lock symbol 11 HomeDialog symbol 12 SuperCool symbol 3 2 Temperature display The following are displayed in normal operation the average cooling temperature The following displays indicate malfunction Possible causes and corrective action see Malfunction FOtOFS 4 Putting into operation 4 1 Transporting the appliance A CAUTION Risk of injury and danger of damage as a result of incorrect transport T
27. on from the leakage area Ventilate the room well Notify the after sales service Do not store explosives or sprays using combustible propellants such as butane propane pentane etc in the appliance To identify these spray cans look for the list of contents printed on the can or a flame symbol Gases possibly escaping may ignite due to electrical components Keep burning candles lamps and other items with naked flames away from the appliance so that they do not set the appliance on fire Please be sure to store alcoholic drinks or other packaging containing alcohol in tightly closed containers Any alcohol that leaks out may be ignited by electrical components Danger of tipping and falling Do not misuse the plinth drawers doors etc as a Step or for support This applies particu larly to children Danger of food poisoning Do not consume food which has been stored too long Danger of frostbite numbness and pain Avoid lasting skin contact with cold surfaces or refrigerated frozen food or take protective steps e g wear gloves Do not consume ice cream water ice or ice cubes immediately and do not consume them too cold Danger of injury and damage Hot steam can lead to injury Do not use elec trical heating or steam cleaning equipment open flames or defrosting sprays to defrost Do not use sharp implements to remove the ice Risk of crushing Do not reach into the soft stop mecha
28. oods Climate rating definitions The appliance is set to operate within specific ambient temperature limits according to its climate rating The correct climate rating for your appliance is indicated on the type plate Note Compliance with the ambient temperatures indicated is required otherwise the cooling performance is reduced Climate for ambient temperatures of rating SN 10 C to 32 C N 16 C to 32 C ST 16 C to 38 C T 16 C to 43 C 1 3 Conformity The refrigerant circuit is tested for leakage The appliance complies with the relevant safety regulations and EC Directives 2006 95 EC 2004 108 EC 2009 125 EC and 2010 30 EU The BioFresh compartment satisfies the requirements of a chill compartment to EN ISO 15502 Note for test institutions Tests are to be carried out according to the applicable standards and guidelines Preparation and testing of the appliances must be carried out taking the manufacturer s loading plans and the notes in the operating manual into account Depending on model and options Appliance at a glance 1 4 External dimensions of the appli ance Fig 2 Designation H mm SKBes 4213 1852 1 5 Saving energy Always ensure good ventilation Do not cover ventilation openings or grille Always keep fan louvres clear Donot place appliance in areas of direct sunlight or next to a stove heater or similar object The energy consu
29. ransport the appliance in a packed condition Transport the appliance upright gt Do not transport the appliance without assistance 4 2 Installing the appliance A WARNING Fire hazard due to dampness If live parts or the mains lead become damp this may cause short circuits The appliance is designed for use in enclosed areas Do not Operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions Depending on model and options Controls and displays WARNING Risk of fire due to short circuit If the mains cable connector of the appliance or of another appliance touch the rear of the appliance the mains cable connector may be damaged by the appliance vibrations leading to a short circuit Stand the appliance so that it is not touched by connectors or main cables gt Do not plug the appliance or any others into sockets located near the rear of the appliance A WARNING Fire hazard due to refrigerant The refrigerant R 600a is environmentally friendly but flam mable Escaping refrigerant may ignite gt Do not damage the piping of the refrigeration circuit A WARNING Fire hazard and danger of damage Do not place appliances emitting heat e g microwaves toasters etc on the appliance A WARNING Blocked ventilation openings pose a risk of fire and damage Always keep the ventilation openings clear Always ensure that the appliance is properly vent
30. rawers and baskets are arranged for optimum energy efficiency on delivery Fig 7 1 Operating panel 10 Type plate 2 Fan 11 Louvre 3 Boxes removable 12 Integrated bottle shelf with glass plate 4 Lighting refrigerator compartment 13 Control panel BioFresh Plus compartment 5 Glass shelf relocatable 14 Humidity regulator 6 Sectioned glass shelf 15 Lighting BioFresh relocatable compartment 7 Rack for tinned food 16 BioFresh Plus compart relocatable ment 8 Bottle rack relocatable 17 BioFresh compartment HydroSafe 9 Bottle holder slidable 1 2 Range of appliance use Intended use The appliance is suitable solely for cooling food in a domestic environment or similar This includes use in for example in staff kitchenettes bed and breakfast estab lishments by guests in country cottages hotels motels and other accommodation for catering and similar services in the whole sale trade Depending on model and options Use the appliance solely in a domestic type of environment All other applications are inadmis sible Foreseeable misuse The following applications are expressly prohibited Storage and cooling of medicines blood plasma laboratory compounds or similar materials and products subject to the Medical Devices Directive 2007 47 EC Use in potentially explosive areas Improper use of the appliance can lead to damage to or spoilage of the stored g
31. safe use of the appliance and understand the resulting risks Children must not be allowed to play with the appliance Cleaning and user maintenance must not be carried out by children without supervision When disconnecting the appliance from the supply always take hold of the plug Do not pull the cable In the event of a fault pull out the mains plug or deactivate the fuse Do not damage the mains power cable Do not operate the appliance with a defective mains power cable Have any repairs to or intervention in the appliance and any change of the mains power cable carried out by the customer service only or by other specialised personnel trained for the purpose Only assemble connect and dispose of the appliance according to the instructions Please keep these instructions in a safe place and pass them on to any subsequent owners Special purpose lamps incandescent lamps LEDs fluorescent tubes in the appliance serve to illuminate the appliance interior and are not suited for room illumination Fire hazard The refrigerant R 600a is environmentally friendly but flammable Escaping refrigerant may ignite Do not damage the refrigerant circuit pipes e Do not allow naked flames or ignition sources to enter the appliance e Do not use any electrical appliances in the interior e g steam cleaners heaters ice cream maker etc e If refrigerant escapes remove any naked flames or sources of igniti
32. t Fig 10 26 and re insert the pin Fig 70 4 from above so that the square sits in the recess gt Attach and engage the cover Fig 10 2 gt Pay attention that the cover fits properly so that the door closes properly and the pin is secured Twist the safety lock Fig 70 3 for removal Snap the faceplate Fig 70 7 onto the door Close the door 4 3 7 Aligning the door Align the door to the appliance housing by way of the two oblong holes in the bottom turn hinge Fig 7 25 To do so unscrew the middle screw Control A WARNING Risk of injury due to the door dropping out If the bearing parts are not screwed into place firmly enough the door may drop out This may lead to severe injuries What is more the door may not close and therefore the appliance may fail to cool properly Screw the turn hinges firmly into place with 4 Nm Check all of the screws and retighten if necessary 4 4 Insertion into a row of kitchen units 7 OS ca 40 1 Stack cabinet 3 Kitchen cabinet 2 Appliance 4 Wall The appliance can be inserted into a row of kitchen units To match the appliance Fig 77 2 to the height of the row of units a suitable stack cabinet Fig 11 7 can be fitted above the appliance When inserting the appliance into a row of kitchen units max depth 580 mm the appliance can be installed directly next to the kitchen unit Fig 77 3 The appliance door projects relative
33. ty period You may be able to rectify the following faults yourself Appliance does not work The appliance is not switched on Switch on the appliance The power plug is not properly inserted in the wall socket Check power plug gt The fuse of the wall socket is not in order p Check fuse The compressor runs for a long time The compressor switches to a low speed when little cold is needed Although the running time is increased as a result energy is saved This is normal in energy saving models gt SuperCool is activated gt The compressor runs for longer in order to rapidly cool the food This is normal A LED on the bottom rear of the appliance at the compressor flashes regularly every 15 seconds The inverter is equipped with a diagnostic LED gt The flashing is normal 13 Decommissioning Excessive noise gt Due to the various speed steps speed regulated compressors can generate different running noises gt The sound is normal A bubbling and gurgling noise gt This noise comes from the refrigerant flowing in the refriger ation circuit gt The sound is normal A quiet clicking noise The noise is produced whenever the refrigeration unit motor automatically switches on or off gt The sound is normal A hum It is briefly a little louder when the refrigeration unit the motor switches on gt The refrigeration increases automat
Download Pdf Manuals
Related Search