pdf file
Contents
1. S rs m WM BI 48 5823 WHTGLS Model Number WM BI 48 5823 WHTGLS This appliance has been tested in accor dance with the UL Standand 2021 for Built In or Wall Mount Appliance fixed and location dedicated electric room 120V AC 60Hz appliances in the United States and Cana i local ler 1500W tion please contact your local dealer HEATER HIGH 1500W 750W NOTE This appliance must be electrically NO HEATER wired and grounded in accordance with local codes In the absence oflocal codes eee us the current CSA C22 1 Canadian Elec MOTOR FLAME AW trical Code in Canada or the ANSI NFPA Appliance Width 57 1 2 or 146 cm 70 National Electrical Code in the United Appliance Height 23 or 58 40 cm States Appliance Depth 6 3 4 or 17 30 cm Gross Weight 82 17 lbs or 37 35kg Plug Location Left side Cord Length 74 81 or 190 00 cm Rough Wall Opening Size 49 X 22 or 124 46 cm X 55 9 cm 21 3 8 7 y ITEE 57 1 2 WM BI 72 8123 WHTGLS This appliance has been tested in accor dance with the UL Standand 2021 for Model Number WM BI 72 8123 WHTGLS Built In or Wall Mount Appliance fixed and location dedicated electric room Voltage 120V AC 60Hz da If you need assistance during installa tion please contact your local dealer 1500W HEATER HIGH 1500W 750W appliances in the United States and Cana NOTE This appliance must be electrically wired and grounded in accordance wit2. 1 Power ON OFF switch 2 Heat control button s 3 Flame control button O ae 4 HEATER LED 5 POWER LED Plug the heater into a suitable outlet 1 Power ON OFF Set this switch to position I to turn the product ON Setting it to O to turn the product OFF The POWER LED will be lit when the fireplace insert is on 2 Heat control button Press the HEAT button repeatedly to set the heater to the desired heat setting The HEATER LED will indicate the current setting for the heater as shown below HEATER LED Red 1500W HEAT OUTPUT HEATER LED Blue 750W HEAT OUTPUT HEATER LED Purple AUTO MODE HIGH 1500W LOW 750W AUTO MODE HEATER INDICATOR HEATER INDICATOR HEATER INDICATOR Auto Mode In this mode the heater will automatically turn on and off When the room temperature drops below 71 F 22 C the heater will turn on to the high heat setting 1500 watt When the room temperature is between 71 and 77 F 22 25 C the heater output will switch to low heat setting 750W When the room temperature goes above 77 F 25 C the heater will turn off 3 Flame control button Press the Flame brightness adjustment button to adjust the flame height and ember bed brightness Press the FLAME control button to cycle through LO MED HI and OFF 23 REPLACING THE REMOTE CONTROL BATTERY When the remote control stops operating or its range seems reduced it is time to replace the batteries with new
3. Lif 21 3 8 MOO INSTALLATION OVERVIEW SITE SELECTION Your new fireplace may be wall mounted installed into existing framing or built into a wall Review and consider all of the following condi tions for installation e Dimensions of the unit e Unit requires a minimum of two 2 wall studs in order to ensure a secure installation Two possible installation methods e Built In page 11 e Wall Mount Page 14 Power supply Wire Gage Voltage WireGage Fuse Wall switch thermostat Wire Gage 18 Gage NOTE A 15 Amp 120 Volt circuit is required A dedicated circuit is preferred but not essen tial in all cases h WARNING Ensure the power cord is not installed so that itis pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire electric shock or injury to persons Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to re duce the risk of fire electric shock and injury to persons To reduce the risk of fire do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater 3 P N NOTE BEFORE YOU INSTALL 1 Select a location that is not susceptible to moisture dust and is away from high traffic locations and things that many catch fire or block openings such as drapes pillows furni ture etc 2 For
4. electrical shock and injury to persons WARNING Do not use this fireplace if any part of it has been under water Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system WARNING Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire electrical shock or personal injury WARNING During any service of this appliance the power to the unit must be turned off First turn the main power switch to the OFF position Then remove the electrical plug from the wall outlet 25 FIREPLACE MAINTENANCE h WARNING Disconnect power before performing any maintenance or cleaning to reduce the risk of fire electric shock or damage LED LIGHT BULB REPLACEMENT LED light bulbs are to be replaced by the manufacturer it s service agent or similar quali fied person in order to avoid hazard h WARNING Allow at least 5 minutes for LED bulbs to cool off before handling bulbs to avoid burns UNIT DISPOSAL Do not dispose with other household wastes To prevent possible harm to the environment or human health from uncontrolled waste disposal recycle it responsibly to promote the sustainable reuse of material resources Contact your local landfill for appropriate disposal instruction 26 TROUBLE SHOOTING 4 WARNING Disconnect power before performing any maintenance and allow to cool before servic ing Only a qualified service person sho
5. appliance can cause melting discolouration or damage to decorations a T V or other electronic components 13 Amantii reserves the right to update and change the specifications and instructions in this manual as needed If in doubt please visit our website at www amantii com for the most recent version of the manual 14 To reduce the risk of fire do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater 15 See directions in Figure 1 This heater is for use on 120 volts The cord has a plug as shown in figure 1 See Figure 1 for grounding instruction An adapter as shown at C is available for connecting three blade grounding type plugs to two slot receptacles The green grounding plug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box The adapter should not be used if a three slot grounded receptacle is available Cover Of Grounded Outlet Box Grounding Pin Al Adapter Grounding IS Means b Fig 1 SAVE THESE INSTRUCTIONS 3 WM BI 26 3623 WHTGLS Model Number WM BI 26 3623 WHTGLS This appliance has been tested in accor dance with the UL Standand 2021 for D ipti Built In or Wall Mount Appl a 7 S fixed and location dedicated electric room 120V AC 60Hz appliances in the United States and Cana Watts 1500W tion please contact your local dealer HEATER HIGH 1500W 750W NOTE This appliance must be electrically NO H
6. bottom right hand side is at position I e The RED amp 5 or 5 buttons control the brightness of the Amber fame To increase the brightness flame height press and release the amp 5 button Each time you press this button the brightness will increase by a small amount until the maximum Is reached To decrease the brightness flame height press and release the 5 button Each time you press this button the brightness will decrease by small amount until the minimum brightness is reached The BLUE amp 5 or 5 buttons control the brightness of the Blue fame To increase the brightness flame height press and release the 5 button Each time you press this button the brightness will increase by a small amount until the maximum is reached To decrease the brightness flame height press and release the amp 5 button Each time you press this button the brightness will decrease by small amount until the 2 When operating the remote make sure you point the remote to the centre of the heater unit and make sure each time you press the button the LED indicator located on top right hand corner of the remote blinks The buzzer inside the unit will beep once if the LED fails to blink check the batteries It takes some time for the receiver to respond to the transmitter Do not PRESS the buttons more than once within two seconds for correct operation 3 Power On O button The power on button at top left
7. corner of the remote is the mains ON OFF power button This will turn off all the functions and the heater will be in standby mode 4 Flame Power On button he O This button controls both the amber and blue colour flame Press this button once to turn ON the flame effect Once the flame effect is ON use the and buttons as explained below to adjust the flame brightness as desired Press this button again to turn OFF the flame effect minimum brightness is reached You can mix the amber and the blue flame to create a realistic flame effect 5 HEATER X Button This button is the heater ON OFF button Press this button to turn the heater ON The heater will always start at high heat setting 2000W To turn OFF the heater press this button again HIGH button Press the high button to switch the heater to high heat setting 2000W LOW button Press the high button to switch the heater to LOW heat setting 1000W ROOM TEMP button Press the high button to switch the heater to AUTO mode Under this mode the heater will operate in similar way as explained above for the manual operation 6 To turn OFF the heater unit completely press the ly button once Realistic Flame Effect The flame effect is controlled by LEDs the LEDs are non replaceable type but have been manufactured to last for long life This remote control will be used on BI 50 FLUSHMT BLKGLS 1 For the remote to function make sure the heater is plugged
8. in and main power switch is turned on Note The heater may release a slight odor the first time it is turned on This is normal The heating elements inside the heater will burn off any accumulated oils or dust during initial heating This may also occur when dust accumulates on the heating elements over periods of non use 2 When operating the remote make sure to point the remote at the center of the fireplace insert Each time you press a button on the remote the LED indicator on the top right of the remote should blink and the fireplace insert will BEEP If the LED fails to blink check the batteries It takes up to one second for the fireplace insert to respond to the transmitter DO NOT PRESS THE BUTTONS MORE THAN ONCE within two seconds This allows the fireplace insert to respond to the remote l 3 Power on C button The power on buiton at top left corner of the remote is the main ON OFF power button This will turn off all the functions heater and display If you turn the fireplace insert OFF then ON the fireplace insert will return to its last heater and display settings 4 Flame Power On button DISPLAY ON OFF This button controls both the ember and flame effect Once the flame effect is ON use the and buttons as explained below to adjust the flame brightness as desired Press this button again to turn OFF the flame effect a The or buttons control the brightness of EMBER To increase the brightne
9. rights which vary from jurisdiction to jurisdiction The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty General Amantii reserves the right to make changes at any time without notice in design material specifications prices and the right to dis continue styles and products 29 Amantii ELECTRIC FIREPLACES www amantil com Date of Purchase Dealer Information
10. the best effect install the firelace out of direct sunlight and away from overhead light ing 3 If possible select a location near an existing electrical outlet for ease of electrical hook up 4 Remove fireplace front fireglass media and all hardware from box and remove all packaging related materials prior to installa tion 5 Plug in the unit then press the POWER key on the unit or remote control ensure the batteries are installed to remote control After this ensure the LED lights are working correctly 6 Press ON OFF key to close the unit then pull the plug from the socket Store the fireplace in a safe dry and dust free location until you are ready to install the fireplace PACKAGING LIST This assembled Electric fireplace is packaged with e One installation and Operation Manual e One remote control e Decorative media See page 15 TOOLS amp BUILDING SUPPLIES NORMALLY REQUIRED TOOLS BUILDING SUPPLIES Phillips Screwdriver Framing Materials Hammer Wall Finishing Mar Saw and or Saber Saw terials Level Caulking Materials Measuring Tape noncumbustable Plum Line Electric Drill and Bits Pliers Square Gloves PACKAGE CONTENTS Part Description Quantity A Glass 1 B Appliance 1 C Wall Mount Bracket 1 D Remote control 1 E Decorative Media 1 CONTENTS anu a 316 In x 1 0 in domnm Wall
11. this Amantii Wall Mount OR Built in electric fireplace you have chosen the finest and most dependable fireplace on the market today A beautiful and functional addition to the finest homes Welcome to the family of satisfied Amantii electric fireplace owners Please read and carefully follow all of the instruction sfound in this manual Please pay special attention to the safety instructions provided in this manual The instructions included here will as sure that you have many years of dependable and enjoyable service from your Amantii product Important instructions Page 3 WM BI 26 3623 WHTGLS Page 4 WM BI 34 4423 WHTGLS Page 5 WM BI 48 5823 WHTGLS Page 6 WM BI 72 8123 WHTGLS Page 7 BI 50 FLUSHMT BLKGLS WHTGLS Page 8 Installation Overview Page 9 Package Contents Page 10 Built In Installation Page 11 Wall Mount Installation Page 14 Media options Page 15 Fire Glass Media Installation Page 16 Front Installation Page 17 Operating the Unit Page 18 Replacing The Remote Control Battery Page 24 Care And Maintenance Page 25 Fireplace Maintenance Page 26 Trouble Shooting Page 27 Service History Page 28 Warranty Page 29 Dealer Contact Information Back Page IMPORTANT INSTRUCTIONS AX WARNING When using electrical appliances basic precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following 1 Read all instructions before installing or using this heater 2
12. EATER 25W wired and grounded in accordance with MOTOR HEATER 19W local codes In the absence oflocal codes MOTORT ANE W us the current CSA C22 1 Canadian Elec trical Code in Canada or the ANSI NFPA Appliance Width 35 1 2 or 90 20 cm 70 National Electrical Code in the United Appliance Height 23 or 58 40 cm States Appliance Depth 6 3 4 or 17 30 cm Gross Weight 27 X 22 or 68 60 cm X 55 9 cm DDDDDDDD 21 3 8 35 1 2 WM BI 34 4423 WHTGLS Modeni ree crete This appliance has been tested in accor a dance with the UL Standand 2021 for Built In or Wall Mount Appliance fixed and location dedicated electric room Voltage 120V AC 60Hz appliances in the United States and Cana a acer wah coulda tion please contact your local dealer 15000 HEATER HIGH 1500W 750W NOTE This appliance must be electrically NO HEATER wired and grounded in accordance with local codes In the absence oflocal codes _ MOTOR HEATER us the current CSA C22 1 Canadian Elec MOTOR FLAME AW trical Code in Canada or the ANSI NFPA Appliance Width 43 1 2 or 110 50 cm 70 National Electrical Code in the United Appliance Height 23 or 58 40 cm PERES Appliance Depth 6 3 4 or 17 30 cm Gross Weight 65 78 Ibs or 29 90kg Plug Location Left side Cord Length 74 81 or 190 00 cm Rough Wall Opening Size 35 X 22 or 88 9cmX 55 9cm ay LLLLLLLLL 43 1 2 21 3 8 a C Fu A E _ 5 _
13. Plug oo Wood Screw C 0 16 in x 0 6 in 18 eS es 0 3 in x 1 5 In 10 FIREPLACE INSTALLATION BUILT IN NEW CONSTRUCTION OR RENOVATION CAUTION Two people may be needed to perform this installation 1 Select a location that is not prone to moisture and is located at least 0 91 m or 3 feet away from combustible materi als such as curtains or drapes furniture bedding paper etc Clearance to combustibles Sides 2in Scm Floor 13 3 4 in 35cm Top 2in 5cm Back Oin 0cm 2 Place the appliance in selected loca tion to see how it will look in the future 3 Mark the desired location on the floor and store appliance in a safe dry and dust free location 4 Prepare a wall with a framed open ing to accomodate the size of your unit Leave at least 1 4 6mm around the edge of the appliance Any new wiring must be done in compliance with local and national codes and other applicable regulations h WARNING To prevent contact with sagging or loose insulation the electric appli ance must not be installed against vapor barrier or exposed insulation Overheating could occur and fire may result min 5 cm 3 2 in NALL min 5 cm 2 in FLOOR min 35cm 13 3 4 in OO I h WARNING Do not attempt to wire your own new outlets or circuits
14. This heater is hot when in use To avoid burns do not let bare skin touch hot surfaces Keep combustible materials such as furniture pillows bedding papers clothes etc and curtains at least 3 feet 0 9 m from the front of the heater and keep them away from the sides and rear 3 Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended 4 Do not operate any heater after it malfunctions Disconnect power at service panel and have heater inspected 5 Do not use outdoors 6 To disconnect heater turn controls to off and turn off power to heater circuit at main disconnect panel or operate internal disconnect switch if provided 7 Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the heater 8 To prevent a possible fire do not block air intakes or exhaust in any manner 9 A heater has hot and arcing or sparking parts inside Do not use it in areas where gasoline paint or flammable vapors or liquids are used or stored 10 Use this heater only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons 11 SAVE THESE INSTRUCTIONS 12 Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance Elevated temperatures on the wall or in the air above the
15. To reduce the risk of injury electric shock or fire use a licensed electrician 11 FIREPLACE INSTALLATION BUILT IN WwW AN NOTE BEFORE YOU INSTALL 1 Lift fireplace and insert into opening Ad just the unit to achieve the desired amount e Units models listed in table below must of depth stick out of the wall a minimum of l 2 1 4 or 5 8 cm 2 Make sure that the power supply port is not behind the wall 3 Level the fireplace 4 Drive mounting screws into the mount ing brackets nailing flanges on the unit and the wall studs The rough wall opening size of the fireplace DDDDDDDD BI 50 FLUSHMT INSTALLATION BUILT IN NOTE BEFORE YOU INSTALL 1 Lift fireplace and insert into opening Ad just the unit to achieve the desired t e BI 50 FLUSHMT units must stick out e eee a o of depth of the wall a minimum of 1 2 or 1 3 cm 2 Make sure that the power supply port is not behind the wall 3 Level the fireplace The rough wall opening size of the fireplace 4 Drive mounting screws into the mount ing brackets nailing flanges on the unit and the wall studs w po fe BI 50 FLUSHMI 40 J d2 j 13mm 13 WwW FIREPLACE INSTALLATION WALL MOUNT cS NOTE BEFORE YOU INSTALL Mounting Noles TOF Stakes for hanging wall bracket It is strongly recommended that the screws be screwed into the wall studs where possible If the wall studs canno
16. ae ELECTRIC FIREPLACES INSTALLATION AND OPERATING INSTRUCTIONS FOR WALL MOUNT AND BUILT IN UNITS WM BI 26 3623 WM BI 26 3623 WHTGLS WM BI 34 4423 WM BI 34 4423 WHTGLS WM BI 48 5823 WM BI 48 5823 WHTGLS WM BI 72 8123 WM BI 72 8123 WHTGLS BI 50 FLUSHMT BLKGLS BI 50 FLUSHMT WHTGLS This manual will enable you to obtain a safe effcient and dependable installation and operatoin of your electric fireplace Please read and understand these instructions before beginning your installation Do not alter or modify this fireplace or its components under any circumstances Any modification or alteration of the fireplace system including but not limited to the firplace and accessories may void the warranty listing and approvals of this sysytem and could result in an unsafe and potentially dangerous installation Amantii electric fireplaces are designed for use as a decorative appliance and or as a supplemental heater They are not intended for continuous use as a primary heat source SAFETY INFORMATION If the information in these instructions are not followed exactly a fire or explosion may result causing property damage personal injury or loss of life Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance INSTALLER LEAVE THIS MANUAL WITH THE APPLIANCE CONSUMER RETAIN THIS MANUAL FOR FUTURE REFERENCE 09 13 01 TABLE OF CONTENTS CONGRATULATIONS In selecting
17. ect wiring for a loose connection or a dead short Repair or replace wiring and or connectors as necessary Circuit Breaker trips or fuse blows when the unit is on Improper circuit current rating Thermal switch has been trippped Turn the unit off and unplug the unit for five minutes Heater does not provide heat when turned on Circuit breaker has been tripped Plug back in and turn the unit on If plug can be reached follow directions for tripped circuit breaker Turn off circuit breaker that supplies electricity to the unit Wait five minutes then flip circuit breaker back on a Unplug the appliance allow appliance to cool for 15 min utes then plug back in a Appliance has overheated and saftey device has cause the ther mal switch to disconnect OR b House circuit breaker has tripped Appliance turns off and will not turn on b Reset the house circuit breaker a Appliance is not plugged into a Check plug and plug it in an eletrical outlet OR b Appliance has overheated and saftey device has cause the ther mal switch to disconnect Appliance will not come on when switch is flipped to ON b Unplug the appliance allow appliance to cool for 15 min utes then plug back in 2 SERVICE HISTORY This heater must be serviced annually depending on usage 28 WARRANTY Amantii Imports Corp Amantii warrants that your newly purchased Amantii
18. electric fireplace is free from manufacturing and material defects for a period of one 1 year from the date of the first purchase subject to the conditions and limitations contained below Warranty Application amp Exclusions This limited warranty applies to your newly purchased Amantii electric fireplace the limited warranty s application is limited to pur chases made in any province of Canada or in any of the 52 States of the United States of America including the District of Columbia Only the original purchaser of the product is eligible for coverage under this limited warranty the warranty is not transferable Products excluded from this limited warranty Light bulbs are not covered by this limited warranty and are the sole responsibility of the owner purchaser Warranty Coverage and Team Products covered by this limited warranty have been tested and inspected prior to shipment and subject to the provisions of this war ranty Amantii warrants such products to be free from defects in material and workmanship for a period of one 1 year from the date of the first purchase of such products The limited one 1 year warranty period for products also applies to any implied warranties that may exist under applicable law Some jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to the purchaser All other warranties expressed or implied with respect to the product its comp
19. equences for the environment and human health The recycling of materials will help to conserve natural resources For more information about collection and recycling of used batteries please contact your local municipality or your waste disposal service Note please operate remote transmitter at a slow measured pace Press the remote control buttons with an even motion and gentle pressure Repeatedly pressing buttons in rapid succession may cause the transmitter to Malfunction 24 CARE AND MAINTENANCE CLEARANCE TO COMBUSTIBLES Keep electrical cords drapery furniture and other combustibles at least 3 ft from the front of the heater and away from the sides CLEANING TRIM Clean the metal trim using a soft cloth slightly dampened with a citrus oil based product and buff with a clean soft cloth Do not use brass polish or household cleaners as these products will damage the metal trim Citrus oil based products can be obtained at supermarkets or hardware stores WARNING Make sure the power is turned off before proceeding Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes lf repairing or replacing any electrical component or wiring the original wire routing color coding and securing locations must be followed WARNING Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire
20. h NO HEATER local codes In the absence oflocal codes MOTOR HEATER us the current CSA C22 1 Canadian Elec 4W MOTOR FLAME trical Code in Canada or the ANSI NFPA Appliance Width 81 or 205 7 cm alee Electrical Code in the United Appliance Height 23 or 58 40 cm Appliance Depth 6 3 4 or 17 30 cm Gross Weight 1331 21 Ibs or 52 41kg Plug Location Left side Cord Length 74 81 or 190 00 cm Rough Wall Opening Size 72 1 2 X 22 or 184 cm X 55 9 cm ALLELLA mi f n 4 lt 4 21 3 8 LLL LL LLL LLL LILLY SIII III IIIS ZII III IIIZ Lo 81 71 1 2 23 BI 50 FLUSHMT BLKGLS WHTGLS NO HEATER AW MOTOR FLAME Appliance Width 51 or 129 6 cm Appliance Height 23 or 58 40 cm Appliance Depth 6 3 4 or 17 30 cm Gross Weight 80lbs or 36 35kg Plug Location Left side Cord Length 74 81 or 190 00 cm Rough Wall Opening Size 49 X 22 or 124 46 cm X 55 9 cm V7 XN This appliance has been tested in accor dance with the UL Standand 2021 for fixed and location dedicated electric room appliances in the United States and Cana da If you need assistance during installa tion please contact your local dealer NOTE This appliance must be electrically wired and grounded in accordance with local codes In the absence oflocal codes us the current CSA C22 1 Canadian Elec trical Code in Canada or the ANSI NFPA 70 National Electrical Code in the United States
21. hing the fireplace mood light ON OFF Switching the color of mood light There are 16 different colors FLASH Switching flash kind of mood light There are 4 different flash styles 19 This remote control will be used on WM BI 26 3623 WHTGLS WM BI 34 4423 WHTGLS WM BI 48 5823 WHTGLS WM BI 72 8123 WHTGLS The button located at the top position of the remote control is ON OFF Press it the flame and ember will be on The heater will be off Press again the fireplace will turn off F Switching the fireplace flame and ember bed light ON OFF It has functions of setting memory Adjust the blue colour brightness of flame and ember Adjust the yellow colour brightness of flame and ember Figure 20 The heater works at 1500W j l The heater works at 750W lO 2 DISPLAY ONOFF BLUE YELLOW TEMP The heater keep working if the room temperature lower than 22 C lt G gt sey The h t working if th t ture higher than 25 e heater not working if the room temperature higher than HEATER Jonorr aaa MOOD LIGHT ON OFF Switching the fireplace mood light ON OFF od anst C FLASH D Switching the color of mood light There are 16 different colors i Switching flash kind of mood light There are 4 different flash styles a 20 This remote control will be used on BI 50 FLUSHMT WHTGLS 1 For remote to function make sure the heater Is plugged in and mains power switch located on the
22. ly done in its sole discretion Amantii may in lieu of replacement choose to refund the purchase price for such product or part Limitations In no event will Amantii including without limitation any of its directors officers shareholders employees consultants agents heirs executors administrators and assigns be liable to the purchaser or any third party whether in contract in tort or on any other basis for any indirect special punitive exemplary consequential or incidental loss cost or damage arising out of or in connection with the sale maintenance use or inability to use the product even if Amantii including without limitation any of its directors officers shareholders employees consultants agents heirs executors administrators and assigns have been advised of the possibility of such losses costs or damages or if such losses costs or damages are foreseeable In no event will Amantii including without limita tion any of its directors officers shareholders employees consultants agents heirs executors administrators and assigns be liable for any direct losses costs or damages that exceed the purchase price of the product Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to the purchaser Application of Provincial and State law This limited warranty gives you specific legal rights and you may also have other
23. nction block 3 Put the plate back and screw back Fix plate Wall Power adaptor port h WARNING Do not attempt to wire your own new outlets or circuits To reduce the risk of injury electric shock or fire use a licensed electrician Appliance has overheated and safety device has cause the thermal switch to discount Unplug the appliance allow appliance to cool for 15 minutes then plug back in Inspect for an objects on or adjacent to the heater that may have locked the airflow or otherwise caused high temperatures to have occurred OPERATING THE UNIT re Plug the fireplace in and turn the power switch to to turn the power on The indicates ON and O indicates OFF When the unit is turned on there will be chiming sound NOTE The power switch is located at the bottom left hand side of the unit When using remote control always point it at the middle of the fireplace and keep not far away than 6 metres This remote control will be used on WM BI 26 3623 WM BI 34 4423 WM BI 48 5823 WM BI 72 8123 The button located at the top position of the remote control is ON OFF Press it the flame and ember will be on The heater will be off Press again the fireplace will turn off ON OFF Switching the fireplace flame and ember bed light ON OFF It has functions of setting memory Adjust the brightness of flame Adjust the brightness of ember MOOD LIGHT ON OFF Switc
24. onents and accessories or any obligation liabilities on the part of Amantii are hereby expressly excluded Limitations to Coverage Under Limited Warranty This limited warranty does not apply to products that have been repaired except by Amantii or its authorized service representatives or otherwise altered This limited warranty further does not apply to defects resulting from misuse abuse accident neglect incorrect installation improper maintenance or handling or operation with an incorrect power source Products made by other manufacturers sold with the product or thereafter are not covered by this limited warranty The use of un authorized components will render this warranty null and void Service Under Limited Warranty Defects must be brought to the attention of Amantii Technical Service by contacting Amantii at 1 888 406 8764 or at 1503 7088 18th Avenue Burnaby British Columbia Canada V3N OA2 Please have your proof of purchase catalogue model and serial numbers available when calling any and all service under the limited warranty requires a proof of purchase of the product Defects Should a product or part covered by this limited warranty be proven to be defective in material or workmanship and during the one 1 year limited warranty period Amantii will replace such defective product or part without charge If Amantii is unable to replace such product or if replacement is not commerically practicable or cannot be time
25. ones Remove the batteries if the remote control won t be used for a long period of time 1 The battery compartment is located on the back end of the remote 2 Press the small tab inward as you slide the battery door open and remove the old batteries 3 Replace with 2 AAA batteries not included making sure the and sides of the battery match the inside of the battery compartment 4 Replace the battery door CAUTION e Always purchase the correct size and grade of battery most suitable for the intended use e Replace all batteries of a set at the same time e Clean the battery contacts and also those of the device prior to battery installation e Ensure the batteries are installed correctly with regard to polarity and e Remove batteries from equipment which is not to be used for an extended period of time e Remove used batteries promptly Note Do not mix old and new batteries Do not mix alkaline standard carbonzinc or rechargeable nicad nimh etc batteries Caution for Ingestion DISPOSAL OF USED BATTERIES Batteries may contain hazardous substances which could be endangering to the enviroment and to human health This symbol marked on the battery and or packaging indicates that used battery shall not be treated as municipal waste Instead it shall be left at the appropriate collection point for recycling By ensuring used batteries are disposed of correctly you will help to prevent potential negative cons
26. re switched off The LED log is shipped in place The log has tabs on each side that hold it secure Remove the side panel to remove the log set and the LED strip 2 Installing the fire glass media Pour the fire glass media into the tray as shown below Fee free to use any combination of fire glass media that you find most appealing 16 FRONT INSTALLATION cy NOTE BEFORE YOU INSTALL It is recommended that two people install the front onto the appliance wear safety glasses and gloves when handling glass 1 Lift fireplace front and line up the brackets with the four 4 shoulder screws on the side of appliance body NOTE Before you lift the front glass Unscrew two screws on both side of the fireplace as below shown 2 Attach the front to the unit Mount Unit Wall Shoulder Screw Built In Installation Wall Mount Installation 17 OPERATING THE UNIT 1 Make sure the appliance is switched OFF refer to page 19 for instruction 2 Attach the provided adaptor to the power port on the right hand side of the unit 3 Plug unit into electrical outlet HARD WIRE INSTALLATION If it is necessary to hard wire this appliance a qualified electrician may remove the cord connection and wire the appliance directly to the house hold wiring 1 Unscrew two screw show in the below Remove the cover plate and the power cord fix piece remove power cord Remove the knockout 2 Attach the wiring to the ju
27. ss of ember bed press and release the button Each time you press this button the brightness will increase small amount until the maximum is reached To decrease the brightness of ember bed press and release the button Each time you press this button the brightness will decrease a small amount until the minimum brightness is reached b The FLAME INTENSITY or buttons control the brightness of FLAME i To increase the brightness flame Intensitypress and release the buttorEach time you pres A j i button the brightness will increase by a small amount until the maximum is reached DIEPLAY mi ONOFF To decrease the brightness flame Intensitypress and release the button Each time you pres Ea E button the brightness will decrease by small amount unit the minimum brightness is reached You can m pinta ember and the flame to create a realistic flame effect HIEH ea Lie es TEP 5 Heater ON OFF button Press this button to turn the heater ON The heater will always start at high heat se PEIS 1500W To turn the heater off press this button again HIGH button Press the high button to switch the heater to high heat setting 1500W LOW button Press the low button to switch the heater to LOW heat setting 750W TEMP button Press the TEMP button to switch the heater to AUTO mode See page 15 for details I 6 To turn off the heater unit completely press the C button once 22 B Main Unit Buttons Operations
28. t be used ensure that plastic anchors are used 1 Affix the provided mounting bracket to the wall e Make sure it is level Height from floor 2 Lift fireplace unit and insert the stakes for 13 3 4 inch N hanging into the keyholes on the back of the unit Floor 3 Check the appliance for stability ensuring that the appliance will not pull free from the wall 4 Drive mounting screws into the mounting bracket on the bottom of unit J Stakes for hanging Wall F Case Feel deel a ee T yi e m i M Back of unit Side view 14 Media options P Models WB BI 26 3623 WM BI 34 4423 WM BI 48 5823 WM BI 72 8123 BI 50 FLUSHMT BLKGLS are shipped with an LED ember log that is pre installed 3 colours of fire glass media are also included See page 16 for log removal instructions See page 16 for media installation instructions i TAn K e5 p A os za F an i i Ti f 5 Koat f fa Clear Harvest Moon Sun Tea LED log Models WB BI 26 3623 WHTGLS WM BI 34 4423 WHTGLS s WM BI 48 5823 WHTGLS WM BI 72 8123 WHTGLS a ep T BI 50 FLUSHMT WHTGLS are shipped with 3 large glass nuggets clear and blue diamond shaped media See page 16 for media installation instructions a Glass nuggets clear and blue diamond shaped media 15 Fire Glass Media Log Installation P 1 Removing the log Unplug the unit from wall and make sure controls a
29. uld service and repair this electric appliance SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Fireplace inner temperature over Reset switch by turning main power switch off and waiting five heatng or home circuit breaker mimutes then turning it back on Fireplace doesn t work has opened Wiring may be loose or the flame Call a qualified service technician Inspect all wiring for motor may be defective loose connections If the wire connections are good replace the flame motor Flame is fixed unmoving LED Light s burt out or wiring is Inspect all wiring for loose connections and repair or replace loose if necessary Inspect light bulbs and replace if necessary Dim or poorly visible flame or log set and ember is not glowing Flame motor is defective Flame sputters Call a qualified service technician and replace flame motor Replace AA batteries in remote control If problem persists there may have been a loss of power to the unit as a pos sible result from a power failure i E Breaker tripped Turn off main power on off switch see figure 4 and or optional wall switch if applicable Low batteries Unit switch and or wall switch in OFF position Remote Control does not work Call a qualified service technician Check the house circuit to ensure it is on a dedicated circuit with proper amp rat ing If the circuit breaker continues to trip or blown fuses insp
Download Pdf Manuals
Related Search