Home

V1.0.1.GV-Smart Box User Manual(SBV101-B-EN).

1. Dynamic Domain Name System provides a convenient way of accessing the GV Smart Box when using a dynamic IP DDNS assigns a domain name to the GV Smart Box so that the Administrator does not need to go through the trouble of checking if the IP address assigned by DHCP Server or ISP in xDSL connection has changed 39 GeoVision Before enabling the DDNS function the Administrator should apply for a host name from the DDNS service provider s website There are 2 providers listed in the GV Smart Box GeoVision DDNS Server and DynDNS org To enable the DDNS function 1 Enable Enable the DDNS function 2 Service Provider Select the DDNS service provider you have registered with 3 Host Name Type the host name used to link to the GV Smart Box For the users of GeoVision DDNS Server it is unnecessary to enter the host name The system will detect the host name automatically 4 User Name Type the user name used to enable the service from the DDNS 5 Password Type the password used to enable the service from the DDNS 6 Click Apply The Update Time from the DDNS will be displayed HTTP Port Settings The HTTP port enables connecting the GV Smart Box to the Web For security integration the Administrator can hide the server from the general HTTP port by changing the default HTTP port of 80 to a different port number within the range of 1024 through 65535 40 U Administrator Mode 4 5 4 IP Filter Setting The Admi
2. Box User s Manual on Software DVD 1 3 System Requirements These are the requirements for the computer that displays the image or controls the GV Smart Box OS Microsoft Windows XP Vista 7 Server 2008 Web Browser Internet Explorer 7 or later E Introduction 1 4 Optimal Camera Installation To get the optimal results for the People Counting and Face Counter function follow the instructions below to install the camera People Counting e The camera should be installed to the ceiling at least 2 5 meters above the floor The camera should face straight down e Position the camera in the middle of the two defined detection zones so that the system can easily identify people when they pass through Positioning the camera in the middle of two gt defined detection zones a e Don t install the camera in such an angle that the size of people varies dramatically in the camera view e Make sure that no doors or any items are ever crossing the middle line where the camera is installed If a door is opened towards the camera place the camera further away from the door e Avoid placing the camera where it can be subjected to direct sunlight or reflections If sharp shadow edges are visible in the camera view the count accuracy might be less than what it normally is e lf the camera has the Auto Gain Control AGC and Auto White Balance AWB features disable them Face Counter e Install the camer
3. Counting f Face Counter r Definition Define Detection Zones Define Object Size Sensitivity 3 r Setting Option v Enable Counting Show ze Counting Result Demo C 1 way counting In Reset at 2way counting o clock Firmware Update Reset Counter j Color Adjustment 2 Save Figure 3 3 1 In the Definition section there are two options m Define Detection Zones Use the mouse to outline detection regions on the video image Number 1 indicates region 1 and number 2 indicates region 2 Defining multiple regions 1 and 2 is practicable Clicking J will clear all defined regions m Define Object Sizes Use the mouse to outline a region matching the normal size of people on the video image If the video is playing first click the Snapshot button to freeze the image before defining 14 BI Accessing the GV Smart Box 2 In the Sensitivity section adjust the detection sensitivity by moving the slider The higher the value the more sensitive the system to motion The default value is 4 3 In the Setting section select Enable Counting and select how you want to count the people m 1 Way Counting When a person appears in region 1 and then enters region 2 it will be counted as 1 in m 2 Way Counting When a person appears in region 1 and then enters region 2 it will be counted as 1 in and when an object appears in region 2 and then
4. Figure 4 13 33 s GeoUision 4 4 Schedule The Schedule section allows you to set a schedule to begin counting upon motion or I O trigger Schedule Settings In this section you can configure schedule time Span 1 Motion 09 se 00 a 217 Iv 00 m C Span 2 Uo w 00 v a0 s 00 v 00 v Next Day Span3 IO wj Q0 w 00 ne 00 100 Next Day C Weekend W 9 Saturday and Sunday Only Sunday C Special Day I m MM DD 01 02 05 DE Qa 10 Figure 4 14 To set up a schedule 1 Select Span 1 and select to detect upon Motion or I O 2 Specify a time period The period that you specify is effective from Monday through Sunday 3 To have the GV Smart Box function all day on the weekend select Weekend and define whether the weekend includes Sunday amp Saturday or Sunday Only 4 To enable GV Smart Box on a specific date select Special Day select the detection mode and type the date Note The detection mode selected in the Schedule section has priority over the settings in the Detection Mode section See 4 1 2 Detection Mode for details 34 U Administrator Mode 4 5 Network The Network section includes some basic but important network configurations that enable the GV Smart Box to be connected to a TCP IP network 4 5 1 LAN According to your network environment select among Static IP DHCP PPPoE and UMTS LAN Configuration In this section you can configure GV Smart
5. System Information Enable a Apply Figure 4 2 20 U Administrator Mode Video Signal Type The GV Smart Box supports both NTSC and PAL video signals Select either NTSC or PAL The live resolution is set to be 360 x 240 NTSC or 360 x 288 PAL There are several frame rates available NTSC 1 3 5 7 10 15 Frame Rate m Overlay Text Enter a text message that will be overlaid on live and captured images e g company name m Overlay Time Select this option to display the time stamp on live and captured images Text Alignment Select a position for the text and time stamp to appear on live and captured images e g down left down right top left or top right Video Saving Setting m Save Image Size Select the size of the captured image to be saved to the mini SD card There are two options CIF and D1 TV Output Port Setting The GV Smart Box allows the direct connection of an external monitor to output live images and counting results immediately When the unit is installed at a place where the network is not accessible the TV Out port can be used for camera adjustment to ensure the image of people or face is captured properly m Frames per second Select a frame rate of 1 5 or 10 for the TV output m Overlay System Information Select Enable to overlay time date detection mode and counting results on the live images of TV output 21 GeoVision 4 1 2 Detection Mode The Detection Mod
6. The table below lists the pin assignment for the shielded wires of the I O Cable with RJ 45 Connector White with Brown Stripe Digital Out 2 sje imm S wne win Orange Sie weoma Note The Wiegand interface is NOT functional now o4 n The I O Terminal Block Relay Output The relay outputs on the terminal block can only drive a maximum load of 5 volts Working in conjunction with the GV Relay V2 module it can drive heavier loads Refer to the figure and table below to connect the GV Relay V2 module to the GV Smart Box Output Device 1 4 GeoVision www geovision com tw l GV RELAY V2 U O 2 99 Connect to Power raran Figure 6 2 White with Brown Stripe Note The GV Relay V2 module is an optional product 55 s GeoUision 6 2 RS 485 RS 232 Terminal Block The 6 pin terminal block located on the rear panel provides the RS 485 and RS 232 interfaces Note RS 485 and RS 232 interfaces are NOT functional now 5V RS485 RS232 TX RS485 RS232RX G Figure 6 3 mm Funeon o 56 Integration with other GV Applications Chapter 7 Integration with other GV Applications The GV Smart Box can integrate with GV applications such as GV Web Report GV System and GV Compact DVR for viewing live images and receiving counting results Compatible Versions e GV Web Report V2 0 or later e GV System V8 34 or later e GV Compact DVR V1 03 or later G
7. enters region 1 it will be counted as 1 out 4 n the Reset at section type a reset counting time between 0 and 23 For example if you type 23 the number of In and Out in the Counting Result section will become zero at 23 o clock daily The daily counting data will be saved in the mini SD card The GV Smart Box then starts counting In and Out numbers again 5 Click the Save button to start the People Counting function Other Configurations available on this Web page Setting m Firmware Upgrade Upgrades the firmware of GV Smart Box over LAN See 5 1 1 Upgrading System Firmware over LAN m Color Adjustment Adjusts the brightness contrast saturation and hue of the video Option m Show Objects If you enable Show Objects the defined masked regions will be displayed on the video image for your reference Demo Illustrates the optimal distance between the camera and object Counting Result Presents the number of people in or out m Reset Counter Resets the number of In and Out to zero immediately The counting data will be saved in the Mini SD card The GV Smart Box then starts counting In and Out numbers again Note To get the optimal people counting results follow the instructions to install the camera See 1 4 Optimal Camera Installation 15 s GeoUision 3 2 1 2 Face Counter To configure the GV Smart Box to count detected faces click the Face Counter tab 1 16 Live View Live View Confi
8. or modify manually 9 Modify manually Date 4000 01 15 Gwylmmidd Time 04 26 54 thh mm ss d Synchronized with your computer Figure 4 19 42 U Administrator Mode Date amp Time on GV Smart Box Display the current date and time on the GV Smart Box Time Zone Set the time zone for local settings Select Enable Daylight Saving Time to automatically adjust the GV Smart Box for daylight saving time Type the Start Time and End Time to enable the daylight saving function Synchronized with a Network Time Server Use the NTP server to automatically update the date and time of the GV Smart Box every 24 hours Type the host name or the IP address of the NTP server for connection Synchronized with your computer or modify manually Manually change the date and time of the GV Smart Box Or synchronize the date and time of the GV Smart Box with the local computer The default date and time setting is set to modify manually The default date is 2000 01 15 while the default time is 04 26 54 43 GeoVision 4 6 2 Storage Settings The GV Smart Box has one SD card slot You can store the counting results or images to the SD card The image is stored in the JPEG compressed format Storage Settings In this section you can configure the disk storage to archive videos and events Storage Settings Enable saving results an Mini SD Card Enable recycling Stop recording or start recycling disk when free space of disk is smalle
9. subnet sequence of the GV Smart Box 1 Insert the Software DVD select IP Device Utility and follow the onscreen instructions to install the program 50 5 Advanced Applications 2 Double click the GV IP Device Utility icon created on your desktop This dialog box appears GV IP Device Utility File Tool Qi x Mac Address IP Address NOTE Test182 D0019DBBBFAF8 192 168 2 49 v1 00 2009 10 12 geovisio 5lpi1r 00055DE0A459 192 168 0 240 v1 00 2009 10 12 Cloud xp1 001D7DA24581 192 168 2 207 v1 00 2009 10 12 AS 400 0013E20100A2 192 168 3 222 v1 00 2009 12 08 Controller 3 0013E20100C1 192 168 3 221 v1 02 2009 12 08 Controller 1 0013E2010757 192 168 2 21 v1 02 2009 12 08 Controller 1 0013E20100C2 192 168 3 44 v1 02 2009 11 18 I0BOX 01 0013E2020202 192 168 1 100 v1 00 2009 09 11 Eddy xp 001D7DA249AF 192 168 2 37 Unknown v8 02 0013E2013EF2 192 168 1 121 v1 47 2009 05 26 GV Smart Box 0013E2018D36 192 168 1 34 v1 00 2009 11 27 BoxCam Demo 0013E20131B1 192 168 1 167 v1 08 2009 06 26 Joe IPCAM1 3M 0013E2013097 192 168 1 116 v1 09 2009 09 22 GV IPCAM1 3M 0013E2012308 192 168 1 13 v1 07 2009 03 13 GVDSP LPR 0013E201255E 192 168 1 253 v1 26 2009 11 18 GV IPCAM1 3M 0013E201519E 192 168 1 221 v1 05 2008 11 06 GVDSP LPRv2 0013E2018D3A 192 168 1 222 v1 00 2009 11 20 Matt IPcam 00D08900A238 192 168 1 231 v1 08 2009 06 26 GVLX 4 V2 0013E2014899 192 168 3 86 v1 02 2009 11 12 Gv Smart Box 0013E2018D64 192 168 2 253 v
10. use this function the Administrator must install I O devices and set up I O BI Accessing the GV Smart Box triggered settings in advance To install I O devices see 4 2 I O Control to configure I O triggered settings see 4 1 2 Detection Mode O Face Only Detects and counts faces only When a face is detected a green circle will appear on the face The Face Only detection can be activated by motion or input trigger To use this function the Administrator must install I O devices or set up trigger types in advance To install I O devices see 4 2 I O Control to configure trigger type see 4 1 2 Detection Mode m Sensitivity Adjust the detection sensitivity by moving the slider The higher the value the more sensitive the system to motion The default value is 4 m Reset at Type a reset counting time between 0 and 23 For example if you type 23 the Viewer and Total numbers displayed on the bottom of the live view window will reset to O at 23 o clock daily The daily face counting data will be saved in the mini SD card Show minimum face size Shows the minimum face size that the GV Smart Box is able to detect For optimal results position the camera so that the area of the detected face takes up 10 to 50 of camera view 2 Click the Save button to start the Face Counter function Other Configurations available on the page Setting m Firmware Upgrade Upgrades the firmware of GV Smart Box over LAN See 5 1 1 Upgrading S
11. 1 00 2009 12 07 GVLX4 RL 3 235 0013E201659E 192 168 3 235 v1 02 2009 10 29 Vandal Proof Demo 0013E2014DEF 192 168 1 165 v1 08 2009 06 26 GVLX 4 V2 008414430003 192 168 1 210 v1 02 2009 12 14 GV IPCAM H 264 0013E2019054 192 168 1 59 v1 00 2009 12 02 VS 02 0013E201415B 192 168 1 92 v1 46 2009 02 11 v8 02 0013E2010FEA 192 168 1 11 v1 46 2009 02 11 GV V802A 001400000001 192 168 3 108 v1 01 2009 12 14 GVDSP LPRv2 0013E2018D0B 192 168 1 155 v1 00 2009 12 15 GV IPCAM1 3M 0013E20151AA 192 168 3 33 v1 08 2009 06 26 GVLX 4 V2 0013E201977D 192 168 3 85 v1 02 2009 12 10 CDYR V2 DemoRoom X 0013E2016CD9 192 168 1 164 v1 02 2009 08 31 GVDSP LPRv2 0013E2012802 192 168 1 144 v1 00 2009 12 11 GV VS02A 008414430002 192 168 3 238 v1 01 2009 12 14 GV V802A 008414430014 192 168 1 50 v1 01 2009 10 05 EX 090650069593939S e e 0 e9Si9S7S99 93 999 Figure 5 2 3 Double click one GV Smart Box in the list This dialog box appears Mac Address 3E201 640 IP Address User Login User Name VSS Port 10000 Password Set IP Address Firmware Upgrade Device Name Export settings Import settings Reboot IP Address 192 7168 209 Subnet Mask 255 255 Default Gateway DNS Server VSS Port oane Figure 5 3 51 GeoVision 4 Click the Firmware Upgrade tab This dialog box appears Mac Address IP Address User Login User Name ERIT VSS Port 10000 Password SetIP Address Firmware Up
12. 3 13 08 43 127 daemon notice GY Smart Box 117 7z MemTotal 110412 KB Figure 4 22 47 s GeoUision 4 6 5 Tools This section allows you to execute certain system operations and view the firmware version Additional Tools In this section you can set the additional tools Firmware Version In this section you can see GV Smart Box firmware version noozo100527 System Settings Restore to factary default settings Load Default Reboot Do vau wish to reboot now Figure 4 23 Firmware Version This section displays the firmware version of the GV Smart Box System Settings Clicking the Load Default button will restore the GV Smart Box to factory default settings The Ready LED on the front panel will turn off Wait until the Ready LED turns on and then you can re log in the GV Smart Box Note After applying default settings you will need to configure the GV Smart Box s network settings again Reboot Clicking the Reboot button will make the GV Smart Box perform software reset The Ready LED on the front panel will turn off Wait until the Ready LED turns on and then you can re log in the GV Smart Box 48 5 Advanced Applications Chapter 5 Advanced Applications This chapter introduces more advanced applications 5 1 Upgrading System Firmware GeoVision will periodically release updated firmware on the website The new firmware can be simply loaded into the GV Smart Box over LAN or by using th
13. Box to work inside of LAN LAN Configuration 9 Dynamic IP address Select this option to obtain IP address from a DHCP server Static IP address Selectthis option ta enter a Static IP address manually PPPoE Selectthis option ta establish a OSL connection User Namel oo Password 0 O Configure connection parameters IF Address 92168 0230 Subnet Mask 2552552550 Fauteriiateway is215801 Primary D NS is216801 Secondary ONS 9216802 Optional Test DHCP Figure 4 15 LAN Configuration m Dynamic IP address The network environment has a DHCP server This option should only be enabled if you know which IP address the GV Smart Box will get from the DHCP server or you have obtained a domain name from the DDNS service provider m Static IP address Assign a static IP or fixed IP to the GV Smart Box Type TCP IP and DNS parameters of the unit in the Configure connection parameters section 35 GeoVision m PPPoE The Network environment is xDSL connection Type the Username and Password provided by ISP to establish the connection If you use the xDSL connection with dynamic IP addresses you must use the DDNS function to obtain a domain name linked to the changing IP address of the GV Smart Box first Configure connection parameters Type the IP address Subnet Mask Router Gateway Primary DNS server and Secondary DNS server of the GV Smart Box IP address 192 168 0 230 Subnet Mas
14. C GeoUision The Vision of Security Smart Box User s Manual V1 0 1 GeoVision GV Smart Box Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use GeoVision 2010 GeoVision Inc All rights reserved Under the copyright laws this manual may not be copied in whole or in part without the written consent of GeoVision Every effort has been made to ensure that the information in this manual is accurate GeoVision Inc makes no expressed or implied warranty of any kind and assumes no responsibility for errors or omissions No liability is assumed for incidental or consequential damages arising from the use of the information or products contained herein Features and specifications are subject to change without notice GeoVision Inc 9F No 246 Sec 1 Neihu Rd Neihu District Taipei Taiwan Tel 886 2 8797 8377 Fax 886 2 8797 8335 http www geovision com tw Trademarks used in this manual GeoVision the GeoVision logo and GV series products are trademarks of GeoVision Inc Windows and Windows XP are registered trademarks of Microsoft Corporation January 2011 Important Notice After updating the firmware from V1 0 to V1 1 you must restore GV Smart Box to factory default settings Refer to 5 2 Restoring to Factory Default Settings for detailed instruction Contents Ghapier i ree elt leiilo aT OO 1 UNE Cau u
15. Hast tC In another PE Local DONS Server IP donec simmer Browse Device Setting Device Port 4000 Login ID admin Password cae Figure 7 8 9 Type the IP address of the GV Smart Box The default value of Device Port is 4000 Click OK The people counting results are now displayed on the specified camera channel 10 To view the people counting results displayed on the POS Live View window go to the main system of the GV System select View Log and select POS Live View wwe EEEE Y mpm 2 Les n e n MPO REO EO E 2 R99 Main system POS Live View Figure 7 9 61 GeoVision 7 3 Connecting to GV Compact DVR The integration enables the GV Compact DVR to overlay the people counting results from the GV Smart Box on the live images of GV Compact DVR To connect to the GV Compact DVR follow the steps below Note You can not access live images from the GV Smart Box in the integration with the GV Compact DVR 1 Enable GV Compact DVR Settings on the Web interface of GV Smart box Figure 4 8 2 Open the OSD menu of the GV Compact DVR select ADVANCED select DISPLAY SETTINGS select INFO DISPLAY SETTING and select GV SMART BOX INFO This dialog box appears IEL INFC INEL II MART BOX INFO SHOW POSITION 1 INSTRUCTIONS SHOW POSITION 1 CANCEL 2 js Figure 7 10 3 Select a position for the recognition results to appear on the live view POSITION 1 refers to the area belo
16. TS Setting Video In Connects a camera Connects an external monitor to output live videos and people counting and face counting results immediately It is useful when you TV Out cannot access the GV Smart Box through the network For details on setting the TV Out function see TV OUTPUT Port Setting in 4 1 1 Video Settings 1 8 2 Rear View e RAO GeoUision Nero uM Ecc Wm LAN 10 100 Mini SD Figure 1 3 No Name runction DC 12V Connects the supplied power adaptor Ethernet Port Connects a 10 100 Ethernet network Connects RS 485 and RS 232 devices See Chapter 6 The I O RS 485 RS 232 Terminal Block 3 Terminal Block Note RS 485 and RS 232 interfaces are NOT functional now 5 A port for digital inputs and relay outputs Insert the supplied I O Port I O Cable with RJ 45 Connector to this port See Chapter 6 The I O Terminal Block _ Inserts a Mini Secure Digital SD card The Mini SD card is Mini SD Card Slot used for storing log data and images 2 4 PJ Getting Started Chapter 2 Getting Started This section provides basic information to get the GV Smart Box working on the network 2 1 Installing on a Network These instructions describe the basic connections to install the GV Smart Box on the network x w bx Power A N Q Ready 9 Load Default lt lt GeoUision Figure 2 1 1 Connect the video output of your came
17. V Smart Box Live View uc reap oun People Counting Results People Counting Results and Face Counting Results GV Compact DVR GV Web Report GV System Figure 7 1 57 GeoVision 7 1 Connecting to GV Web Report The integration enables the GV Web Report to keep track of and analyze people counting and face counting results from the GV Smart Box To connect to the GV Web Report follow the steps below 1 Enable GV Web Report function on the Web interface of the GV Smart Box Figure 4 9 2 Type the host name or IP address port number user name and password of the GV Web Report and click Apply The default port number is 30000 3 Onthe main screen of GV Web Report click Service and select Data Service to start receiving data from the connected GV Smart Box amp GeoVision GV Web Report service Browse Tools Help Start all services Stop all services Data Service Web Service Logout Exit Figure 7 2 4 Select Web Service Figure 7 2 to enable the Web interface of GV Web Report 5 Go to the Web interface of GV Web Report You can start accessing the live view people counting and face counting results from the GV Smart Box 58 Integration with other GV Applications 7 2 Connecting to GV System The integration enables the GV System to overlay the people counting results received from the GV Smart Box on the live images To connect to the GV System follow the st
18. V Smart Box can connect to up to 2 VSM centers for central monitoring onnection 1 Connection 2 Vital Sign Monitor Server Setting In this section you can configure the connection to VSM Server and tasks to perform Activate Link Host name or IP Address 197 1880 11 Port Number S609 User Name emartBox Password 22222 Connection Status Status Connected Connected Time vwVed Mov 3 11 47 22 2010 Figure 4 7 To set up VSM 1 2 3 4 5 Select Activate Link to enable the function Type the Host Name or IP address of the VSM server Type a port number or keep the default value 5609 Type a valid User Name and Password to log into VSM Click Apply The Connection Status should display Connected and the connected time 2f s GeoUision 4 3 2 Compact DVR Setting The GV Smart Box can connect to the GV Compact DVR For details on the connection see 3 Connecting to GV Compact DVR Type the IP address port number user name and password of the GV Compact DVR Select one channel of the GV Compact DVR to overlay the people counting results on the channel The default port number is 10000 Compact DVR Settings In this section you can configure the connection to Compact DVR and tasks to perform Compact DVR Settings Enable IP Address 132 158 0 1 Fart Number DOO User Name admin Password Device Mame GY Smeart Box Mapping Compact DYR Channel Number Channeli Channel 2 Cha
19. a inside an entrance pointing horizontally outward The face counting function is designed to detect front view faces only e Avoid installing the camera where it can be subjected to direct sunlight or reflections The lighting of the entrance where you set the camera should be sufficient but not be too bright or dark Light should be distributed evenly across faces without too much light coming from one side If sharp shadow edges are visible in the camera view the count accuracy might be less than what it normally is 1 5 Recognition Limitations on Face Counter e Recognition Angle Front face only side face cannot be recognized e Face with Mask Filter Not recommended for people with long beard or mustache e Recognition Area Range The area of the detected face must take up 10 to 50 of camera view EE Introduction 1 6 Reference for Recording Capacity of a 1G Mini SD Card For Face Counter function a mini SD card with 1G capacity can store approximately 40 000 log events both MDB and images at D1 resolution and 97 000 log events at CIF resolution For People Counting function a mini SD card with 1G capacity can store approximately 52 000 log events at D1 resolution and 122 000 log events at CIF resolution Function People Counting CIF 122 000 Face Counter CIF 97 000 People Counting BEA Face Counter D1 40 000 Log Events MDB and Images 1 7 Options Optional GV applications can expand your GV Sm
20. art Box s capabilities and versatility Contact your dealer for more information For details on connecting to optional devices see Chapter 7 Through the Web browser the GV Web Report keeps track of and analyzes the people counting and face counting results from multiple GV Smart Boxes The integration brings you the following benefits e live view display from GV Smart Boxes e Data analysis of people counts and face counts Compatible version V2 0 or later GeoVision Analog and Digital Video Recording Software In most of documents the GV System also refers to Multicam System GV NVR System and GV Hybrid DVR System at the same time The integration brings you the following benefits e live view display from GV Smart Boxes e People counting results overlaid on the live images Compatible version V8 34 or later The GV Compact DVR is a mobile video recorder The integration brings you the following benefit e People counting results overlaid on the live images Compatible version V1 03 or later E Introduction 1 8 Overview This section identifies the various components of the GV Smart Box 1 8 1 Front View Figure 1 2 No Name Fu nction Power LED Indicates the power is supplied Ready LED Indicates the unit is ready for connection 3 Default Button It resets all configurations to their factory settings See 5 2 Restoring to Factory Default Settings USB Port Connects a UMTS modem See 4 4 3 UM
21. cel Status standby Camera list Preview Record Emart Bax Cameral GX Smart BoxiCameral Apply Clase Figure 7 5 Click Query After the GV Smart Box is found click Apply This dialog box appears pomme E PEERS 182 158 0 230 10000 Camera Connected 360x240 JPEG Gy 5mart Box Scan Camera OK Figure 7 6 Right click the GV Smart Box to select a display channel To overlay the people counting results on the live images from the GV Smart Box go to the main system of GV System select Configure select Accessories select POS Application Setting select POS Device Setup and click the New tab This dialog box appears Printer Type TCRAP Pot Device h POS1 Manning cameet I POS Module General gt COM Part 1 e m o E t Use Codepage Mapping Trace mode g Add Cancel Figure 7 7 Integration with other GV Applications 8 Select TCP IP Port from the Printer Type select a POS device to display people counting results select the same camera number you selected in step 6 to map live images and counting results together from the GV Smart Box select General from the POS Module and click Data Capture IP Address Setting This dialog box appears Data Capture Box IP 5etting i Fixed IP Device IP 182 188 0 230 t IP Info in DONS Server O dipmap carn EY Domain Name t IP info in GV Data Capture Local DONS Server Device Mame f n
22. d Period From 2010 06 01 00 00 00 To 2010 06 01 23 59 59 33 in Total Back to Search 2 3 5 6 1 Start Time Age mart 2010 06 01 0 i6 744 na Photo f f n3 nt 1 434 na Photo na Phota na Photo Figure 4 12 Up to 100 log events can be listed on each page You can click Photo to see the snapshot of the log event No Description Display the total number of the detected faces within the queried period Display numbers of events Display the host name of the GV Smart Box Display the start time of the event Display the recognition time spent on the event Click to display the snapshot of the event 32 U Administrator Mode Producing Statistic Diagrams The GV Smart Box can present the people counting results in a diagram You can only query the People Counting log events on a specified date Select the desired date and click Display The following diagram appears You can easily see the peak time of people counting results in the statistical diagram The hourly numbers of people in and out are illustrated both in the diagram and the table Units Day View Statistic Diagram U 1 2 3 4 5 7 B 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 27 Time 2010 06 01 Total IN 4288 OUT 2851 Time 1 2 3 4 a 6 Fi a 9 10 11 1 1314 15 16 17 18 19 20 21 22 23 24 In 309 361 354 364 358 368 371 357 3613613613130 0 0 0 00 00 0 0 0 OD Out 241 241 239 240 240 240 242 241 241 241 240 2050 0 0 0 0 0 0 0 0 0 0 0
23. device designed for indoor environments such as shops and offices Connecting to any analog camera the GV Smart Box counts the number of visitors or faces Having this data not only helps you keep an eye on your properties but also helps retailers identify peak traffic hours providing valuable information for making strategic decisions Without installing any software you can easily access the live images and counting data of the GV Smart Box from anywhere in the world through a computer using the IE browser You can also integrate the GV Smart Box with GV applications such as GV Web Report GV System and GV Compact DVR to support extended functionality tn Live Images People Counting and Face Counting Results f Network N EE eee E S E User 1 User 20 IE browser IE browser Figure 1 1 1 1 Key Features Counts the number of visitors Counts the number of faces Easily accessible Web based interface to watch live views query database and customize settings Triggers alarm when faces covered with masks are detected Supports UMTS Integrates with GV Web Report GV System or GV Compact DVR Connects to VSM and sends alerts in the event of I O trigger video lost and network disconnection Supports adjustment of video attributes Sets detection mode by schedule 1 2 Packing List p o mp N GV Smart Box x 1 I O Cable with RJ 45 Connector x 1 Power Adaptor x 1 GV Smart Box Software DVD x 1 GV Smart
24. e IP Device Utility included in the Software DVD Important Notes before You Start Before you start updating the firmware please read these important notes 1 While the firmware is being updated A the power supply must not be interrupted and B do not unplug the Ethernet cable if the cable is the source of power supply Power over Ethernet or PoE supported 2 Do not turn the power off for 5 minutes after the firmware is updated 3 If you use the IP Device Utility for firmware upgrade the computer used to upgrade firmware must be under the same IP and subnet sequence of the GV Smart Box WARNING Interruption of power supply during updating causes not only update failures but also damages to your GV Smart Box In this case please contact your sales representative and send your device back to GeoVision for repair 49 s GeoUision 5 1 1 Upgrading Firmware over LAN 1 In the Live View window People Counting or Face Counter click the Firmware Upgrade button This dialog box appears Remote Config Firmware Upgrade Browse Version File Figure 5 1 2 Click the Browse button to locate the firmware file img saved at your local computer 3 Click the Upgrade button to begin upgrading 5 1 2 Upgrading Firmware by Using the Utility The IP Device Utility provides a direct way to upgrade the firmware to multiple GV Smart Boxes Note the computer used to upgrade firmware must be under the same IP and
25. e a valid password to enable the UMTS service from your network operator MTU Type the Maximum Transfer Unit The default value is 1500 Keep Check UMTS Connection Select this option to check the UMTS connection status and use the drop down list to specify the desired time length for check frequency Check VPN Connection Select this option to check the VPN Virtual Private Network connection status To check the IP address type the target IP address in the Check Target IP Address field UMTS Authentication Protocol Use the drop down list to select the UMTS Authentication Protocol provided by your network operator 3G Connection Status Indicates the connection status of UMTS or VPN 38 U Administrator Mode 4 5 3 Advanced TCP IP This section introduces the advanced TCP IP settings including DDNS Server and HTTP port Advanced TCP IP In this section you can set the advanced TCP IP configuration Dynamic DNS Server Settings In this section you can configure your GV Smart Box to obtain a domain name by using a dynamic IP Enable Service Provider Geovision DDNS Server v ex Rex i Update Time Refresh HITP Port Settings In this section you can change the default HTTP port number 80 to any port within the range 1 65535 It is a simple method to increase system security using port mapping You can configure HTTP connection to an alternative port HTTP Part Figure 4 17 Dynamic DNS Server Settings DDNS
26. e section allows you to set the GV Smart Box to begin counting upon input trigger or upon motion detection When face detection fails an output device will be triggered for example an alarm may be activated for warning in Face with Inverse Mask Filter function or a door lock may not be unlocked in Face with Mask Filter function To have the I O application you must set up the I O devices on the GV Smart Box first by referring to 4 2 1 Input Settings Detection Mode In this section you can configure the detection mode GPIO 9 Enable Trigger Input C Input 1 Input 2 Trigger digital output relay output1 Output 2 TrggerPeriod 3 second Motion Enable Figure 4 3 GPIO Begins face counting upon input trigger m Trigger Input Select Input 1 and or Input 2 and the GV Smart Box will begin face detecting after the input device is triggered If both options are selected face detecting will begin after either input device is triggered m Trigger digital output relay Select Output 1 and or Output 2 to trigger an output device if a face in Face with Mask Filter function or no face in Face with Inverse Mask Filter function is detected after the time interval specified below m Trigger Period The GV Smart Box will attempt to detect faces for the number of seconds specified For example of the Face with Inverse Mask Filter function if you set the interval to 30 seconds the output device will be trigger
27. ed if the system cannot detect any faces within 30 seconds after the input device is triggered Note The GPIO function works with Face with Mask Filter Face with Inverse Mask Filter and Face only options in Face Counter See 3 2 1 1 Face Counter 22 U Administrator Mode Motion Begins people or face counting upon motion detection The Motion triggered counting option applies to the People Counting function and the Face Only option of Face Counter function 23 s GeoUision 4 1 3 GV Smart Box Settings The GV Smart Box can connect to the GV System For details on the connection see 7 2 Connecting to GV System Once you have connected the GV Smart Box to the GV System the live images of the GV Smart Box will be transmitted to the GV System and the people counting results can be overlaid on the live images as well GV Smart Box Settings Name Setting Mame G Smart Box PP Apply Period of Connection Checking Second 0 256 sery OO AB 0 255 sec c Connection Port Settings FOS Part Number 4000 POS poe oe 3088 Number Live Center Port fife Apply Figure 4 4 Name Setting Type a descriptive name for the GV Smart Box Period of Connection Checking Set the time interval in seconds between each reconnection attempt Connection Port Settings Both POS Port and POS ACK Port are used for transmitting the counting results to the GV System The default port numbers are 4000 and 3999 respec
28. eoUision Chapter 3 Accessing the GV Smart Box Two types of users are allowed to log in the GV Smart Box Administrator and Guest The Administrator has unrestricted access to all system configurations while the Guest has the access to live view and network status configurations only Note To access the Web interface of GV Smart Box make sure the Web browser you use is Internet Explorer 7 or later 3 1 Accessing Your Surveillance Images Once installed your GV Smart Box is accessible on the network Follow these steps to access your surveillance images people counting and face counting results 12 Start the Internet Explorer browser Enter the IP address or domain name of the GV Smart Box in the Location Address field of your browser Is Ip view Favorites Tools He z ites Meneses gt ix a j Search ser avori tes 44 A Address E http 192 168 2 58 ssi cgi Login hkm C GeoVision GV SMART BOX SETUP Figure 3 1 Enter a login name and password e The default login name and password for Administrator are admin e he default login name and password for Guest are guest A video image similar to the example in Figure 3 2 is now displayed in your browser Accessing the GV Smart Box Note To enable the updating of images in Internet Explorer you must set your browser to allow ActiveX Controls and perform a one time installation of GeoVision s ActiveX component onto your computer 3 2 F
29. eps below 1 To configure the GV Smart Box to connect to the GV System select Video and Motion and select GV Smart Box Settings See 4 1 2 GV Smart Box Settings 2 To add the live view images from the GV Smart Box go to the main system of GV System click the Configure button select General Setting select Camera Audio Install and select IP Camera Install This dialog box appears IP Device Setup Serer address Pot Cam NO Status Video Resolution Brand Add Camera 192 158 2 205 Mo Disconnect 182 158 3 211 Ma Disconnect GY IPCAM 1 3M H 264 GV Scan Camera 192 158 1 148 Mo Disconnect GV Smart Boxilamerat 192 158 3 183 Cameras Connected 1280x102 4 H 2 64 GV Fish Eye Camera GV FE 192 158 0 187 Camera Connected 352x2BB JPEG GV P Speed Dome GV SDD 192 158 3 232 Camera Connected j52x288 JPEG GV IP Speed Dome GV SD Impart Camera IP Device Utility OK Figure 7 3 3 Click Add Camera This dialog box appears Select Brand Serwer lP 192 168 0222 HTTP Pot 80 User name almn Password Brand Device Please select the brand of IP camera ia Close Message Close Figure 4 59 GeoVision 4 60 Type the Server IP HTTP Port User name and Password of the GV Smart Box Select GeoVision from the Brand and GV Smart Box from the Device This dialog box appears GV Smart Box Livery Server Port 10000 Can
30. ge SeNGS eieaa een ene ee eee ee IET eee eee 44 1 6 ero MES lt 1 2616 0 U 9 TR T tm 46 4 6 4 Log Information ueesessessssesssessseeennen enne nnnm nnne nnn nnn nnns 4T AO TOON f 48 Chapter 5 Advanced Applications 49 5 1 Upgrading System Firmware ccccccccseccceeceeeceeeeeeeeeeeeeesueeseeeeseeeseeeesueeseeesaneees 49 5 1 1 Upgrading Firmware over LAN ccccccseccseeceecceecceeceeeceeeseesseeesseeseeenaes 50 5 1 2 Upgrading Firmware by Using the Utility eesseessesssssse o0 5 2 Restoring to Factory Default SettingS cc cccccccceecceeeseeeeeeeeseeeseeeeseeeseeeeseeees 53 Chapter 6 The I O Terminal Block 54 OL GIL FRED 54 62 RS 485 RS 232 Terminal BIOCK 5 eon ret eren pue mundi aede ces cts a Sive ida te pa OKu ene 56 Chapter 7 Integration with other GV Applications 57 7 1 Connecting to GV Web Report sesessssssssssseseeeeenenn nennen nennen nnns 58 7 2 Connecting to GV SYSICM essiensa eu ee dente rtasuciuscndPsES pacUu d PE NUNG inn 59 7 3 Connecting to GV Compact DVR ssssssssssssseeeen nennen nennen nna 62 a ce J ecin a ji a ee DEDE EROR ORDER QUI DATA LINE a ieee nT arene 63 PE Ie b NM RR RR m 64 E Introduction Chapter 1 Introduction The GV Smart Box is a standalone
31. grade Device Name Export settings Import settings Reboot wm SIRE O Upgrade all devices Figure 5 4 5 Click the Browse button to locate the firmware file img saved at your local computer 6 If you like to upgrade all the GV Smart Boxes in the list select Upgrade all devices 7 Type Password and click Upgrade to process the upgrade 02 5 Advanced Applications 5 2 Restoring to Factory Default Settings To restore to default settings use the Load Default button on the front panel of GV Smart Box See No 3 Figure 1 1 1 Unplug and plug the power cable The Ready LED turns off 2 Press and hold the Load Default button until the Ready LED turns on 3 Release the Load Default button The process of loading default values is complete and the GV Smart Box starts rebooting itself Note Before Ready LED is on again do not unplug the power cable otherwise the loading of default values will fail 53 s GeoUision Chapter 6 The I O Terminal Block 6 1 I O Port GV Smart Box provides the I O Cable with RJ 45 Connector for the extensible connection to other I O devices A RJ 45 connector and a bundle of shielded wires are on the each end of the cable Strip the desired wires first and connect the auxiliary devices with the right wires according to the following pin assignment Then insert the RJ 45 Connector to the I O Port on GV Smart Box No 4 Figure 1 3 Figure 6 1 Pin Assignment
32. guration nthis section you can see and configure the default camera view People Counting Face Counter Setting Alarm Type Face Only Sensitivity 3 Reset at o clock ne m ET T 3 h Show minimum face size E330 A3EOJ I Y Color Adjustment Firmware Update Reset Counter Save Figure 3 4 In the Setting section the following options are available m Alarm Type three detection alarm types are available for Face Counter Face with Mask Filter The alarm type needs I O devices to work with After the input device is triggered the system will start detecting faces the output device will only be triggered when a face is detected within the time interval specified For example after a door sensor input is triggered the door lock output will only open if a face is detected by the system within 30 seconds To use this function the Administrator must install I O devices and set up I O triggered settings in advance To install I O devices see 4 2 O Control to configure I O triggered settings see 4 1 2 Detection Mode Face with Inverse Mask Filter The alarm type needs I O devices to work with After the input device is triggered if the system is unable to detect faces within the time interval specified the output device will be triggered For example after an ATM card is inserted into an ATM machine a security alert will be sent if GV omart Box is unable to detect a face within 30 seconds To
33. k 255 255 255 0 Router Gateway 192 168 0 1 Primary DNS server 192 168 0 1 Secondary DNS server 192 168 0 2 For details on the DDNS function Dynamic DNS Server see 4 4 4 Advanced TCP IP 36 U Administrator Mode 4 5 2 UMTS UMTS stands for Universal Mobile Telephone System UMTS is a third generation 3G broadband packet based transmission of text digitized voice video and multimedia at data rates up to 2 megabits per second UMTS offers a consistent set of services to mobile computer and phone users no matter where they are located in the world After a mobile broadband device supporting UMTS HSDPA etc is attached to the USB port on the front panel and the UMTS function is enabled the GV Smart Box can have wireless broadband access For supported mobile broadband devices see Appendix n this section you can configure the UMTS settings UMTS Settings Set Up UMTS Device Enable FIM Number AFN User Name Password MTU keep Check UMTS Connection Check Interval Check VPN Connection Check Target IP Address Inann UMTS Authentication Protocol 36 Connection Status Disconnection Figure 4 16 3 GeoVision UMTS Settings PIN Number Type the PIN number that is provided by your network operator APN Type the Access Point Name that is provided by your network operator Username Type a valid username to enable the UMTS service from your network operator Password Typ
34. l m 2 WZ Packing Sleesia 2 1 3 System Requirements ssesssssssssssseseseseeee nnne nne nnne nena nnne sn se ass s asas a sese nis 2 1 4 Optimal Camera Installation leeeseeeseeseeeseeeeeerennnnnnnnn nnn 3 1 5 Recognition Limitations on Face COuntel ccccceccceececeeeceeeeceeeeeeeeaeeeeeeeseeseees 4 1 6 Reference for Recording Capacity of a 1G Mini SD Card ssss 5 Mee ORION RR m 6 FE i1 nee nee een een ree eee nee er een eee eee ree ene eee 7 MEL CU E T 1 892 Rear View craters cence reste ees etre tee acess petty bathers ees roc seem rome EH 8 Chapter 2 Getting Started 9 2 1 Installing on a Network cccccccecceseceecceeeceeeceeeceeecueecseeceeecaeeeeeeeaeseeesaeesaeeseeeseeenes 9 2 2 Assigning an IP FC SS aes ses du eea LED EE Coe MUN UU Resp MEE E UU M UNE DUUE 10 2 3 Configuring Basic Features seessssssssessesseseseeee nennen nnne nnns nnne nn nnn nns 11 Chapter 3 Accessing the GV Smart Box 12 3 1 Accessing Your Surveillance Images ccccceccceececeeeceeeeceeeeeeeeeeeeseeeeseeeseeeeaeess 12 3 2 Functions Featured on the Main Page ccccccceccceecceeeseeeeeeeeeeeeeeeeeeteeeseeeeeeesees 13 3 2 1 People Counting and Face Co
35. n 4 2 2 Output Setting The GV Smart Box can connect up to 2 output devices e g alarms There are six output signals available N O Open Circuit N C Grounded Circuit N O Toggle N C Toggle N O Pulse and N C Pulse Choose the one that best suits the device you are using For Toggle output type the output continues to be triggered until a new input trigger ends the output For Pulse output type the output is triggered for the amount of time you specify in the Trigger Pulse Mode for x seconds field Output Setting In this section you can configure GV Smart Box digital output port Digital Output 1 Normal State Enahle General Made 9 Open Circuit N O Grounded Circuit Mic Toggle Made Open Circuit MO Grounded Circuit WC Pulse Mode Open Circuit Mio Grounded Circuit NIC Trigger Pulse Made for seconds 60 Digital Output 2 Normal State Enable General Mode 9 Open Circuit WO CO Grounded Circuit NIC Toggle Mode Open Circuit WO CO Grounded Circuit WC Pulse Mode Open Circuit Mio Grounded Circuit NIC Trigger Pulse Made for seconds 60 Figure 4 6 26 U Administrator Mode 4 3 Events amp Alerts 4 3 1 VSM Vital Sign Monitor The GV Smart Box can connect to the central monitoring station VSM and VSM can receive text alerts in the event of video lost I O trigger and network disconnection To monitor through VSM you must already have a subscriber account on VSM One G
36. nd Motion Live View gt Video Settings Detection Mode GV Smart Box Settings Y I O Control Input Setting Output Setting Y Events and Alerts gt VSM Compact DVR Setting Web Report Setting Inquire Database Y Schedule Camera 1 Y Network Status gt LAN UMTS Advanced TCP IP gt IP Filtering Y Management Date and Time Storage Settings User Account Log Information Tools Y Logout ive View Live View Configuration n this section you can see and configure the default camera view People Counting Face Counter 3 o and Motion 4 iew gt Video ettings gt Detection art Bo ettings ontrol Input Setting Output Setting its and Alerts LI gt Compact D Setting Web Report Setting cE EE I 9 Ca Io o e s Ham g S Figure 4 1 19 s GeoUision 4 1 Video and Motion This section introduces Video Settings and GV Smart Box Settings GV System connection settings that allow you to customize People Counting and Face Counter functions 4 1 1 Video Settings Video Settings In this section you can set video signal type Video Signal Type Frames per Signal Farmat Live Resalutian second NTSC 360 240 15 PAL 360 288 Overlay Text GEOVISION Overlay Time Text Alignment Down Left Iv Video Saving Setting Save Image Size CIF v TV OUTPUT Port Setting Frames per second 1 Overlay
37. nistrator can set IP filtering to restrict access to the GV Smart Box IP Filter Setting In this section you can allow or deny network connection listed in the table Only 4 filter entries are supported IP Filtering Enable IP Filtering Mo IP Address Range in CIDR format Action Customize 192 168 0 3 Deny Filtered IP dee 192168 1 20r192 168 1 0 24 Actian ta take Figure 4 18 To enable the IP Filter function 1 Enable IP Filtering Enable the IP Filtering function 2 Filtered IP Type the IP address you want to allow or deny 3 Action to take Select the action of Allow or Deny to be taken for the IP address you have specified 4 Click Apply 41 s GeoUision 4 6 Management The Management section includes the settings of date and time SD card and user account Also you can view the firmware version and execute certain system operations 4 6 1 Date amp Time Setting You can set up the date and time appearing in the image s caption Date and Time Settings In this section you can configure time and date or just synchronize with a HTP server Date and Time on GV 5mart Box Thu Jun 3 15 21 10 2010 Time Zone Enable Daylight Saving Time Stat Md hha End three Synchronized with a Network Time Server Synchronized with Network Time Server MTP Hostname or IP Address o Update period 24 hours Update Time AM 05 10 Synchronized with your computer
38. nnel 3 Channel 4 Figure 4 8 28 U Administrator Mode 4 3 3 Web Report Setting The GV Smart Box can connect to the GV Web Report For details on the connection see 1 Connecting to GV Web Report Type the host name or IP address port number user name and password of the GV Web Report and click Apply The default port number is 30000 You can click Export all button if the network was interrupted to resend all data to the GV Web Report The Connection Status is shown on the bottom of the page to show whether GV Web Report is connected and the time of connection Web Report In this section you can configure the connection to Web Report Web Report 4 Enable Host name ar IP Address 192 158 0 123 Port Number 30000 Password Connection Status Status Connected Connected Time Wved Mov 3 11 47 22 2010 Figure 4 9 29 s GeoUision 4 3 4 Database Inquiry You can query people counting and face counting data from the mini SD card In addition the people counting results can be presented in statistical diagrams Note The log data is recorded in the mini SD card Make sure you have inserted the mini SD card into the GV Smart Box before you query the data Web Query In this section you can query data from local database Web Query Event Filter 9 counter Face Counter DST Enable Non DST DST From To oou via WEB poro w i SiC Hour wj Hour wj Day View Statistic Diagram Co
39. o types of password protection Guest password for restricting unwanted users from accessing the GV Smart Box and Administrator password for restricting who can enter privileged commands Default Guest login name and password are guest Default Administrator login name and password are admin User Account In this section you can change the administrator account and password Administrator Account Guest User Account Figure 4 21 46 U Administrator Mode 4 6 4 Log Information The log contains dump data that is used by service personnel for analyzing problems Log Information In this section you can see all system activities Startup time log In this section you can see latest booting time of system System Log In this section you can see all system activities Jun 3 13 07 37 127 daemon notice cGV 2mart Box 117 23 Cached 34256 kB Jun 3 13 07 37 127 daemon notice cGV 2mart Box 117 23 auapcached 0 kB Jun 3 13 07 37 127 daemon notice GY Smart Box 11 72z How time Thu Jun 3 13 07 37 2010 Jun 3 13 07 37 127 daemon notice GY Smart Box 11 72 Total mem 11 231z Total Free 35466 Jun 3 13 07 38 127 daemon info GY Smart Box 1163 1l92 168 2 152 777 Message CheckConnectOR Size a8 Jun 3 13 06 09 127 daemon info GY Smart Box 1163 192 168 2 152 777 Message CheckConnectOKR Size 8 Jun 3 13 06 40 127 daemon info GY Smart Box 1163 192 168 2 152 779 Message CheckConnectOK Size 8 Jun
40. ra to the BNC video input Connect the hub or switch on the LAN to the unit s 10 100 Mbps Ethernet port Connect the power supply to the power input 2 I9 Wait until both Power and Ready LEDs are on Then you can set the IP address for the unit s GeoUision 2 2 Assigning an IP Address Designed for use on an Ethernet network the GV Smart Box must be assigned an IP address to make it accessible Note The GV Smart Box has a default address of 192 168 0 230 The computer used to set the IP address must be under the same IP and subnet sequence assigned to the unit 1 Open your Web browser and type the default IP address http 192 168 0 230 2 n both Login and Password fields type the default value admin Click Apply 3 In the left menu select Network and then LAN to begin the network settings e GeoVision LAN Configuration Video and Motion inthis section you can configure GV Smart Box to work inside of LAN pO Control Events and Alerts LAN Configuration Network k c Status Dynamic IP address Selectthis option ta obtain IP address from a DHCP server Static IP address Selectthis option ta enter a Static IP address manually k UMTS PPPoE Select this option ta establish a DSL connection Advanced UserName i ICPP Password 0 IP Filtering hk Man Management Configure connection parameters Logout IP Address 192 168 0230 Subnet Mask 255 255 2550 RauteriGate
41. rthan 32M Disk Infomation Total Size Used Size Free space Utilization Remove Format 7625 200 7426 2 Unit Megabyte Must format far initial SO card set up Figure 4 20 To add a SD card 1 Insert a SD card to the SD card slot 2 Click the Refresh button to detect the SD card The total size used size free space and utilization of the SD card will be displayed Note that it may take several seconds for your Web browser to update the information from the SD card 3 If you like to format the SD card or erase all data stored on it click the Format button To remove a SD card 1 Click the Remove button 2 When you are prompted to confirm the action click Yes The page will be refreshed and the partition information will be cleaned 3 Remove the SD card from the SD card slot Note The captured images may be lost if you do not remove the SD card properly 44 U Administrator Mode Storage Settings m Enable saving results on SD Card Enable this option to save the counting data and images onto the SD card m Enable recycling If this option is checked the system will overwrite the oldest stored files when the space of the SD card is lower than the specified space If this option is not checked the system will stop recording when the specified space is reached Note The GV Smart Box does not support SD High Capacity SDHC cards 45 s GeoUision 4 6 3 User Account The GV Smart Box has tw
42. tively The Live Center Port is used for accessing the Web interface of GV Smart Box on the browser When you want to access Web interfaces of multiple units of GV Smart Box on the same computer set different Live Center Ports for each GV Smart Box otherwise you cannot access more than one GV Smart Box at the same time 24 U Administrator Mode 4 2 l O Control The I O terminal block on the rear panel of GV Smart Box provides the interface for digital inputs and relay outputs For details on the I O terminal block see Chapter 6 4 2 1 Input Setting The GV Smart Box can connect up to 2 input devices e g sensors Input Setting In this section you can configure GV Smart Box digital input port Digital Input 1 Enahle Mame Input Normal State Open Circuit Mio Grounded Circuit NIC Latch Made Enable Trigger digital output relay Output 1 L Output 2 Digital Input 2 Enable Harme Input2 Normal State Open Circuit Mio Grounded Circuit NIC Latch Made Enable Trigger digital output relay Output 1 L Output 2 Figure 4 5 m Name Type a descriptive name for the input device m Normal State Set up the input state to trigger actions by selecting Open Circuit N O or Grounded Circuit N C m Latch Mode Enable this option to have a momentary output alarm m Trigger digital output relay Select the output s to be triggered after the input is activated 25 GeoVisio
43. unctions Featured on the Main Page This section introduces the features of the Live View window and Network Status on the main page The two features are accessible by both Administrator and Guest Main Page of Guest Mode C GeoVision pares Y Video and Motion _ 7 Video and Motion Live View Configuration n n Live View gt Live View Network inthis section you can see and configure the default camera view gt Status Y Network Logout People Counting Face Counter Definition Status gt Define Detection Zones Region 1 EHEH 2 C Define Object Size c3 Sensitivity 3 Setting Option Counting Result M Enable Counting B uus C 1 way counting Demo In 58 Reset at 2 way counting o o clock Out 40 Firmware Update Reset Counter Color Adjustment 2 E Figure 3 2 13 C GeoVision 3 2 1 People Counting and Face Counter In the Live View configuration window the People Counting and Face Counter functions are available for configuration These two functions cannot be enabled simultaneously You can only enable either People Counting or Face Counter at one time The configuration of these two functions is accessible by both Administrator and Guest 3 2 1 1 People Counting To configure the GV Smart Box to count people click the People Counting tab Live View Live View Configuration this section you can see and configure the default camera view People
44. untel cccccccceeceeecceeeeseeeeeeeeseeeeeeeeseesaues 14 322 NOBNOIK SAUS ieruistexqeboked ue E EEEREN d RUE 18 Chapter 4 Administrator Mode 19 Me WACO ANG MOTO MU 20 4 1 1 Video Settings ees mmm 20 A2 WI CUS CUOM MOOG creeren ae nE EEEE EOR 22 4 1 3 GV Smart Box Settings ccc cceccceseeseeeceeeeeeeceseeeeeeseeesgeeseeesseeenaees 24 cv TO CORTO eee ee eee ce eee ee ne ne ee eee ee eee 25 d 2 1 VON S ING scessextends iussus eE saver Enden oa cones NOR S 25 z E MER Geb drin o RE MT 26 4 3 Events amp Alerts MRNIRRORCCE 27 4 3 1 VSM Vital Sign Monitor sseeeseesseseseeeeeennnmnnnennnnnnnn 2f 4 3 2 Compact DVR Setting uus eiuniese pre tbt eta pn paper Oui uu tu udduaul depre duce sapnvx cuu duse 28 4 3 3 Web Report Setting eeeseesssesssessseeseeennenen nnne nnne nnne nnn nnns 29 AOA DADIS gels RN 30 ed Sonde ccussmescsimu delete ice cece uicem ese csuPsu deed NNNM PN i ies eee e OUI MIA DUI ER EM IPIE UNUS 34 z Ho INS ONG M E ER 35 BN EAN E m 35 2H UMT c 37 25 5 Jgvdiced TC PIT accums de etd ua TREK RUpIUN mA NIE MA PH UM EFC FU De QE 39 mor M FET NN RETE 41 46 AVIA GCG WE M RR m 42 4 6 1 Date amp Time Setting 20 0 0 cece ceccceeceeeeeceeeeeeeeseeeseeeeseeeseeeeseeseeeeseeeeaes 42 402 Stra
45. unter event only z010 Du wi AE Figure 4 10 30 U Administrator Mode Querying Data To query log data of People Counting 6 T Select Counter from the Event Filter If you want to query log events recorded during the Daylight Saving Time period select DST from the DST Enable otherwise select Non DST Select time period and click Search This log event list appears 1 Quired Period From 2010 06 01 00 00 00 To 2010 06 01 23 59 59 1179 in Total in Total BecktoSearh Search 2 3 METET m 4 5 6 7 8 9 10 11 12 Next gt gt NO Time CNT12 CNT21 Picture 1 GY Smart Bo v 1 2010 0 1 41 35 Photo 2010 06 1 11 41 355 1 Photo Figure 4 11 Up to 100 log events can be listed on each page You can click Photo to see the snapshot of the log event 1 Description Display the total number of people counted within the queried period Display numbers of events Display the host name of the GV Smart Box Display the time of the event Display the number of people in T Display the number of people out Click to display the snapshot of the event 31 GeoVision To query log data of Face Counter 1 Select Face Counter from the Event Filter 2 f you want to query log events recorded during the Daylight Saving Time period select DST from the DST Enable otherwise select Non DST 3 Select time period and click Search This log event list appears 1 Quire
46. w the camera name POSITION 2 refers to the top of the live image POSITION 3 refers to the area above camera name HIDE refers to hiding the text on the live image 62 Specifications Specifications 63 C GeoVision Appendix Supported Mobile Broadband Device HUAWEI E169 E220 E1692 E1750 EC169C USB Modem HSDPA UMTS EDGE GPRS GSM Verizon U727 U760 USB Modem EVDO MC950D HSDPA UMTS EDGE GPRS GSM 64
47. waw is215801 Primary DMS ig2t68 01 Secondary DINS 9216802 Optional Figure 2 2 4 Select Static IP address Type IP Address Subnet Mask Router Gateway Primary DNS and Secondary DNS in the Configure connection parameters section 5 Click Apply The GV Smart Box is accessible by entering the assigned IP address on the Web browser lg Getting Started Important 1 Dynamic IP Address PPPoE and UMTS should only be enabled if you know which IP address the GV Smart Box will get from the DHCP server or ISP Otherwise you must use the Dynamic DNS service to obtain a domain name linked to the GV Smart Box s changing IP address first For details on Dynamic IP Address and PPPoE settings see 4 4 4 Advanced TCP IP 2 If Dynamic IP Address PPPoE or UMTS is enabled and you cannot access the unit you may have to reset it to the factory default and then perform the network settings again To restore the factory settings see the Default button in 1 8 1 Front View 2 3 Configuring Basic Features Once the camera is properly installed these important features can be configured using the browser based configuration page and are discussed in the following sections in this manual e Date and time adjustment see 4 5 1 Date and Time Setting e Login and privileged passwords see 4 5 3 User Account e Network gateway see 4 4 Network e Video format resolution and frame rate see 4 1 1 Video Settings 11 e G
48. ystem Firmware over LAN m Color Adjustment Adjusts the brightness contrast saturation and hue of the video Reset Counter Resets the number of Viewer and Total on the Live View window immediately The counting data will be saved in the Mini SD card The Viewer presents the current number of detected faces on the image The Total presents the total number of detected faces Up to 8 faces can be detected on the image at the same time Note To get the optimal face counting results follow the instructions to install the camera See 1 4 Optimal Camera Installation For details on the limitations of Face Counter function see 1 5 Recognition Limitations on Face Counter 17 GeoVision 3 2 2 Network Status To view the network status in the left menu click Network and select Status 18 Network Status Information In this section you can see an overview of GV Smart Box status Current Status Information interface IP Acquirement MAC Address IP Address Subnet Mask Gateway Domain Mame Server 1 Domain Marne Server 2 Figure 3 5 Wired DHCP 013E201B88D 182 158 0 23U 255 255 252 0 192 168 0 1 158 935 1 1 8 8 8 8 U Administrator Mode Chapter 4 Administrator Mode The Administrator can access the system configuration via the Internet Five categories of configurations are included in the system configuration Video and Motion I O Control Events and Alerts Network and Management Y Video a

V1.0.1.GV-Smart Box User Manual(SBV101-B-EN).

Contents

Download Pdf Manuals

Related Search

Related Contents