Model D3128 - User Manual, Revision 1.04
Contents
1. Please note that the LabVIEW development suite version 6 1 or greater from National Instruments is required to use the included VI s and Meadowlark Optics Inc does not provide this development package with PixelDRIVE 3000 Itis assumed that the customer has experience programming in LabVIEW and understands good programming practices Meadowlark Optics Inc cannot offer customer support for LabVIEW application development If a developed or modified LabVIEW application is to be distributed in any way please contact Meadowlark Optics for licensing and copyright details 6 Care and Maintenance of the SLM Optics The D3128 Spatial Light Modulator is a precision instrument and should be treated accordingly It is especially important to observe good optics laboratory practices with the optical head Do not allow the optics components to become soiled and avoid excessive unnecessary cleanings If cleaning is required the drop and swab method is recommended Wear finger cots or gloves and use lint free optics tissue Laboratory grade methanol is recommended and then only in evaporative amounts 1 e use one drop do not douse the optics Laboratory grade acetone can be used only if deemed absolutely necessary and again only in evaporative amounts Never use water based cleaning solutions never use methyl ethyl ketone MKE or other solvents never immerse the optical head or saturate the optics with solvent and never scrub or b2. The selected pixel is highlighted yellow in the On Screen Pixel Array Changes to the voltage will be rendered in the On Screen Pixel Array Selecting or changing the voltage of a pixel by clicking the On Screen Pixel Array will update these controls 4 1 6 Pattern Generation e CONSTANT Sets each pixel in the array to a uniform value e LINEAR The voltages will vary linearly across the array from the voltage of pixel to the voltage of pixel 128 e PARABOLA Varies the voltage quadratically across the array o NEG POS Specifies whether the parabolic voltage function will open down or up o MAGNITUDE Scales the parabolic voltage function o HORIZONTAL Shifts the parabolic voltage function left or right o VERTICAL Applies a DC offset to the parabolic voltage function e SINUSOID Varies the voltage sinusoidally across the array O AMPLITUDE The zero to peak amplitude of the sinusoidal voltage function O CYCLES The number of sinusoidal cycles across the pixel array O VERTICAL The DC offset of the sinusoidal voltage function O PHASE Horizontal shift of the sinusoidal voltage function e RANDOM Randomly calculates a value between the specified upper and lower limits for each pixel 4 1 7 Pattern Adjustment e OFFSET o HORIZONTAL Shifts the pixel pattern left or right Pixels at the ends wrap as they are shifted o VERTICAL Applies a DC offset to the array pattern o APPLY Adjusts the pixel array by the specified vertical and hor
3. 000000 2 000000 3 000000 lt lt Pixel 3 Values 1 000000 2 000000 3 000000 lt lt H Pixel 127 Values 1 000000 2 000000 3 000000 K Pixel 128 Values Frame 1 Frame 2 Frame 3 Pixel Values Pixel Values Pixel Values Figure 11 PixelDRIVE 3000 ASCII Data File Format Linear Array One header row one row of frame durations and 128 rows of pixel data Each column denotes a frame of pixel data meadoulark optics polarization D3128 User s Manual rev 1 04 16 solutions Appendix B Firmware Updater The D3128 internal firmware can be reprogrammed by the user when new versions are released by Meadowlark Optics Update is accomplished by using the firmware updater program included on the PixelDRIVE CD In order to use the firmware updater program the D3128 must be powered on and connected to an available USB port on the host computer Perform the following steps to reprogram the D3128 firmware 1 Install the firmware updater software on a PC running Microsoft Windows 98SE or later Place the included CD in the CD ROM drive open the Firmware updater folder and double click setup exe 2 Start the firmware updater software by clicking StartIPrograms Meadowlark Optics Firmware updater The following screen will appear Ef Meadowlark Optics Firmware Up dat meadoulark optics Firmware Erasing Programming Updater a xi File Name Cycle power on the controller in preparation fo
4. development for the D3128 Future releases might include development resources for alternative programming platforms What is the purpose of the SYNC and TRIGGER connectors on the front panel The TRIGGER connector generates an output pulse coinciding with any update to the pixel array This signal can be used to synchronize external devices to the D2138 The SYNC connector is not presently active it is reserved for future applications What are valid x y pixel indices for the hexagonal array Pixel indices must occur as odd odd or even even pairings For example 0 0 and 1 1 are valid pixel indices but 0 1 is invalid Horizontal index boundaries are 6 lt x lt 6 Vertical index boundaries are 12 lt y lt 12 I calculated a frame of pixel values for the hexagonal array using a spreadsheet and a formula f x y When I loaded the frame into PixelDRIVE 3000 the function was distorted appearing stretched verticall y or horizontally What happened The aspect ratio of the indexing convention the x and y coordinates of the pixels is 1 4 3 not 1 1 When calculating pixel values use f x V3 y or f x y V3 What are the power on default voltage and temperature values After powering on the D3128 the array will be driven to 10 volts for 500 ms switched to 5 volts for 500 ms then switched to zero volts Upon completion of the power on voltage cycle the USB connection to the PC will be established The
5. e OFFSET RESCALE o DC ADJUST is a constant value to be added to each pixel o RESCALE is a multiplier by which each pixel will be scaled o APPLY rescales and offsets the pixel array e ADD NOISE Adds or subtracts a random value to each pixel o NEG LIMIT The maximum value that would be subtracted from each pixel o POS LIMIT The maximum value that would be added to each pixel 3 1 5 Temperature Control STATUS LED illuminates green when the SLM temperature is within 1 C of the setpoint UPDATE LED blinks when the SLM temperature is measured SETPOINT C Sets the desired operating temperature of the SLM TEMP C Shows the current measured temperature of the SLM updated automatically at 2 sec intervals Note that automatic temperature measurement is disabled when frame cycling is active 3 1 6 On Screen Pixel Array e Shows the voltage settings of each pixel as a greyscale value black corresponds to zero volts maximum retardance and white corresponds to ten volts minimum retardance e Clicking a pixel highlights it as the selected pixel with a red dot the angle of the red dot is indicative of the pixel value e Clicking and rotating a pixel varies its value e The extra pixel control at x y 6 12 of the on screen pixel array controls the large test pixel 3 2 The Indexing Convention of the Hexagonal Pixel Array The on screen pixel array locates pixels in the SLM by x y coordinate indices Fig 7 shows t
6. go to My Computer or Windows Explorer double click on the CD ROM drive and double click on Autorun exe in the Autorun directory 3 Hexagonal 127 Pixel Array Two available D3128 optical configurations are the 127 pixel hexagonal array and the 128 pixel linear array Both optical configurations include software that has been customized to the geometry of the pixel array The software that drives the hexagonal array is detailed here please refer to Section 4 for a discussion of the software that drives the linear array 3 1 PixelDRIVE 3000 Software for the Hexagonal Array The D3128 includes PixelDRIVE 3000 a user friendly software interface for control of the spatial light modulator Here we detail the functions of PixelDRIVE 3000 Also included on the CD are LabVIEW VI s meadouwlark optics D3128 User s Manual rev 1 04 4 polarization solutions compatible with National Instruments LabVIEW versions 6 1 or later that end users can include in their own development efforts Voltage levels here refer to the amplitude envelope about a 2 kHz square wave with zero DC offset Never apply a voltage with a non zero DC component to a liquid crystal cell As voltage levels are mentioned in the present context it is important to bear in mind that we are describing the amplitude envelope about a 2 kHz square wave For instance a driver signal described as invariant actually refers to a square wave with a steady amplitude
7. liquid crystal spatial light modulator solution The optical head includes the LC pixel array configured in either a 128 pixel linear or 127 pixel hexagonal geometry The LC is thermally stabilized by two independent temperature feedback control sub circuits The optical head mounts in a laboratory setup using standard 14 20 or 8 32 hardware and it electrically connects to a compact control module by one convenient 25 pin cable The control module includes an output trigger channel for integrating the SLM with other laboratory equipment and connects easily to a PC with a USB cable The software provides control of individual pixels as well as functions that treat the array as a whole dual channel temperature control multiple frame configuration timing control and file 1 0 all through an attractive user friendly interface The CD includes LabVIEW development resources for customers wishing to design control features using National Instruments Lab VIEW 1 Nematic Liquid Crystal Technology The Basics 1 1 Nematic LCVR Physical Architecture Typical nematic Liquid Crystal Variable Retarders LCVRs such as the LVR and LRC series by Meadowlark Optics are constructed using optically flat fused silica windows coated with transparent conductive indium tin oxide ITO A thin dielectric layer is applied over the ITO and gently rubbed creating parallel micro grooves for liquid crystal molecular alignment Two windows are then carefully aligned and
8. optics D3128 User s Manual rev 1 04 19 polarization solutions As the firmware is being erased and reprogrammed the status will be displayed as shown below DO NOT disturb power to the D3128 while it is erasing or reprogramming if memory 1s corrupted it will be required to return the unit to Meadowlark Optics for reprogramming 7 Es Meadowlark Optics Firmware Updater x Ef Meadowlark Optics Firmware Updater 3 xj Firmware meadowlark optics Firmware meadowlark optics Updater Erasing Programming Updater Erasing Programming File Name Code Size File Name Code Size Exit Program Exit j emi kein d3128_305 hex 16CE Pilea ral d3126_305 hex 16CE WARNING WARNING Do Not Disturb Power to the Controller Do Not Disturb Power to the Controller While Programming While Programming After programming is complete the following screen appears When the controller power is cycled the status light should flash a pattern corresponding to the version number of the new firmware The new firmware version may also be determined by clicking the Meadowlark Optics logo in the upper left corner of PixelDRIVE 8 Es Meadowlark Optics Firmware Updat er meadowlark sptics Firmware a igr Erasing Programming complete Cycle power on the controller File Name d3128 305 hex Thank you For using the Meadowlark Optics Firmware Updater Have a nice day Do Not D meadoulark optics D3128 User s Manual rev 1 04 20
9. polarization solutions Appendix C Software Licensing IMPORTANT CAREFULLY READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT BEFORE USING THIS SOFTWARE This Meadowlark Optics Inc License Agreement is a legal agreement between you Licensee and Meadowlark Optics Inc Licensor for the enclosed computer software and any associated media printed materials and online or electronic documentation Software By installing or otherwise using the Software Product you agree to be bound by the terms of this License Agreement If you do not agree to the terms of this License Agreement do not use or install the Software Product you may however return it to your place of purchase for a refund SOFTWARE LICENSE AGREEMENT This Software License Agreement Agreement is entered into between Meadowlark Optics Inc Licensor and you as Licensee Licensee 1 Definitions a Software The term Software shall mean the enclosed computer software and any associated media printed materials and online or electronic documentation The term Software includes any corrections bugs fixes enhancements updates or other modifications including custom modifications to such computer programs ds License a Grant of License Licensor grants Licensee pursuant to the terms and conditions of this Agreement a limited revocable non exclusive non transferable license to use the Software which has been bu
10. sequence until the user deactivates frame cycling USB DEVICE Selects among several Meadowlark Optics USB devices when several Meadowlark Optics USB devices are connected to the PC OPEN FILE Reads frame and pixel array configuration data from an ASCII text file see Appendix A for the file specification SAVE FILE Writes the current frame and pixel array configuration to an ASCII text file see Appendix A for the file specification RESET Performs a soft reboot of the D3128 controller and re enumerates the USB connection EXIT Quit PixelDRIVE 3000 3 1 2 Frame Control FRAME SELECTOR slider and numeric control Selects a pixel array from the sequence and renders it on the display ADD FRAME Adds a new frame to the sequence after the current frame DELETE FRAME Removes the current frame from the sequence DURATION MSEC Specifies the duration time in milliseconds of the current frame APPLY TO ALL Sets the duration time of all frames to that of the current frame meadoulark optics D3128 User s Manual rev 1 04 6 polarization solutions 3 1 3 Hex Frame Generation e PIXEL Use the arrows or enter horizontal and vertical pixel indices to change the selected pixel Change the pixel value to the desired level Hint The horizontal and vertical indices must both be either odd or even 1 e 0 0 and 1 1 are valid but 0 1 1s not valid e UNIFORM Sets each pixel in the array to a uniform value e LINEAR Applies a linear gra
11. spaced a few microns apart The cavity is filled with birefringent nematic liquid crystal material Electrical contacts are attached and the device is environmentally sealed Anisotropic nematic liquid crystal molecules form uniaxial birefringent layers in the liquid crystal cell An essential feature of nematic material is that on average molecules are aligned with their long axes parallel but with their centers randomly distributed as shown in Fig 1 With no voltage applied the liquid crystal molecules lie parallel to the glass substrates and maximum retardation is achieved Fused Silica ITO a Alignment Layer Maximum Spacer Retardance j V 0 LC Molecules b Minimum LC Molecules tipped with Retardance applied voltages V gt gt 0 PP 9 Figure 1 Liquid Crystal Variable Retarder construction showing molecular alignment a without and b with applied voltage drawing not to scale meadoulark optics D3128 User s Manual rev 1 04 polarization solutions When voltage 1s applied liquid crystal molecules begin to tip perpendicular to the fused silica windows As voltage increases molecules tip further causing a reduction in the effective birefringence and hence retardance Molecules at the surface however are unable to rotate freely because they are pinned at the alignment layer This surface pinning causes a residual retardance of 30 nm even at high voltage 20 volts We achieve zero or any custom retardance
12. the envelope is unchanging in time but the signal itself Gf measured with an oscilloscope for instance oscillates about the zero voltage axis It 1s important to note that the square wave is always symmetric about the zero voltage axis As previously mentioned zero offset is critical for nematic liquid crystal cells 4 PixelDRIVE 3000 HEr meadowlark optics PIXELDRIVE 3000 Es STO LIGHT MODULATOR INTERFACE Main Functions Configure Live I j Cvde A Once Repeat Frame Frames ntrol Hex Pattern Gene F a P ER 0 ge Hex Pattern Adjust 2 0 DC Adjust Rescale To 000 Eio E Aceh Temperature Control E l Setpoint emp Duration msec ap Status Update C _ eso Mosz Apply to A Figure 4 PixelDRIVE 3000 Hex User Interface Pixel DRIVE 3000 provides an easily accessible user interface by which to control the pixels of the spatial light modulator The software grants control of the pixel array through manipulation of the individual pixels and through spatial functions that can be applied to the pixel array as a whole Multiple arrays called frames can be configured independently of one another A sequence of frames can be cycled and the duration of each frame can be specified The software also enables temperature control and monitoring From here the user interface will be considered in six sections shown in Fig 5 In addition to the controls and indicators within the six sections highlight
13. 000 3 000000 lt Test Pixel Values Horizontal Vertical Frame 1 Frame 2 Frame 3 Pixel Indices Pixel Indices Pixel Values Pixel Values Pixel Values Figure 10 PixelDRIVE 3000 ASCII Data File Format Hexagonal Array One header row one row of frame durations and 128 rows of pixel data Two columns of x y coordinates the remaining columns denote frames of pixel data meadoulark optics D3128 User s Manual rev 1 04 15 polarization solutions A 2 File Format for the Linear Array SLM The second row 1s tab delimited and contains frame duration times in seconds The 128 remaining rows are tab delimited and consist of pixel values Pixel values are sorted in ascending pixel order Columns represent frames and must be tab delimited and the PixelDRIVE 3000 frame sequence order is determined by the order in which columns appear in the data file The file format is illustrated in Fig 11 A voltage vs x function V x can be evaluated to produce pixel values voltage values must be sorted as x varies from 1 to 128 In generating a list of pixel voltages o Po od o ay ae aS ES qe e ES a pa ES A e SE amp x amp K a F se Po ES S S Linear 1 02 2 00 3 128 56 04 2004 23 58 00 Frame 0 100000 0 400000 0 350000 lt Durations sec 1 000000 2 000000 3 000000 lt Pixel 1 Values 1 000000 2 000000 3 000000 lt Pixel 2 Values 1
14. DRIVE 3000 Es STO IGHT MODULATOR INTERFACE ee Setpoint Temp Pixel Select Duration msec a nds status p Amplitude Cycles Vertical Phase Pixel Level s Horizontal Vertical poa a o GENO EMO OM PA Figure 8 PixelDRIVE 3000 Linear User Interface Pixel DRIVE 3000 provides an easily accessible user interface by which to control the pixels of the spatial light modulator The software grants control of the pixel array through manipulation of the individual pixels and through spatial functions that can be applied to the pixel array as a whole Multiple arrays called frames can be configured independently of one another A sequence of frames can be cycled and the duration of each frame can be specified The software also enables temperature control and monitoring From here the user interface will be considered in seven sections shown in Fig 9 In addition to the controls and indicators within the six sections highlighted in Fig 9 clicking the Meadowlark Optics logo displays software and firmware version information meadoulark optics D3128 User s Manual rev 1 04 10 polarization solutions ES PixelDRIVE 3000 EER meadowlark sptics PIXELDRIVE 3000 ns A iat MoOoULATOR INTERFACE Main Functions Configure Live Once Repeat Load Cyde Pattern Open Save oe e EF A IE E inear Pixel Control 1 Setpoint Temp Status Update C EC E pm Duration msec Figure 9 Sectioned PixelDRIVE 3000 L
15. VERS WIN2K_XP directory The drivers for Windows 98SE and Windows ME are in the USB DRIVERS WIN98_ME directory 8 Start the PixelDRIVE 3000 software by clicking StartIPrograms Meadowlark Optics PixelDRIVE 3000 pad eas adi 500 mA cable Power USB Personal Computer meadoulark optics D3128 User s Manual rev 1 04 11 polarization solutions D3128 Spatial Light Modulator Table of Contents IA Po o eects S ii Table of Onte S ein a ai iii 1 Nematic Liquid Crystal Technology The Basics sscccsssccssscccsssccssssccsssccsssccssscccsssccsssccessscessscoeess 1 1 1 Nematic LCVR Physical Architecture occcooccconcncnoncnnnncnnnoncnnnonnonononnnnnnonononnnonnnnonannnnnnnnonannnnnns 1 1 2 Building a Liquid Crystal Pixel Array cooonccoocncnoncnnononononcnnnonnnnoncnnnnnnonononnnonnnnonannnonnnnonannnnnos 3 2 Hardware Setup and Configuration sssecsseccsccesccosseccsseccscosccoscecccceocceocseocseocccosceosscossceosceosseossecsscesseesse 3 2 1 Laboratory and System Requirements for the D3128 oonncccnoncnnoccnnnncnnonocnnoncnnnonccnonacnnoncnnnns 3 2 2 Setup Procedure for the D3128 ooonncconncncoccnnoncnnnnccnnnnnononnnnnonnononnononnnnnnnnnnonnnnnonnnnnnnnnonnnnnns 3 3 Mexaconal 127 PIxClL AGA y rin A E caisa 4 3 1 PixelDRIVE 3000 Software for the Hexagonal Array ooonccconncncoccncnocnnononnnoncnnonnnnnoncnnonacnnonnnnnns 4 3 1 1 Main Functions csscs0hcuiaecn
16. ark optics D3128 User s Manual rev 1 04 2 polarization solutions 1 2 Building a Liquid Crystal Pixel Array The conductive ITO layers of a typical LC cell are uniform so that an applied square wave voltage signal establishes a uniform electric field throughout the LC filled region of the cell With a spatial light modulator the conductive ITO on one piece of glass is etched into a pattern much like the copper layer of a printed circuit board is etched into a pattern that is useful for the desired circuit design The ITO on the other piece of glass is uniform to provide a common ground The etched piece has ITO in the desired pixel pattern and traces that electrically connect each pixel to the edge of the glass The SLM LC cell is assembled and filled in the same manner as a variable retarder A unique type of multi conductor cable adheres to the glass and electrically connects the array of pixel connectors to the circuit that drives them 2 Hardware Setup and Configuration 2 1 Laboratory and System Requirements for the D3128 e 100 240 VAC 47 63 Hz 500 mA utility power e A PC with an available USB port e Minimum PC requirements to run the included PixelDRIVE 3000 software are a Pentium processor 64 MB RAM 20 MB hard drive space 800x600 pixel 16 bit color graphics a CD ROM and Microsoft Windows 98SE ME 2000 or XP e Recommended PC specifications are a 1 GHz Pentium III processor 256 MB RAM 20 MB hard drive space 1024x768 pi
17. asdnesenoatanmsisundoeiteseedecuhasoaoueneadennebansae tinnacdeanasonbaouiseuncncieseabag ous 6 Ae PP A 6 LS TACK Erame Genera ista 7 ial Hex paler AAA S ono a 8 Al FEmperatlte COntal sacos 8 A Ro sn e o reer oer err ene 8 3 2 The Indexing Convention of the Hexagonal Pixel Array oooccccoccncoccnnnncnnnoncnnonccnnoncnnnnncnnoncnnnns 8 d MAC AE LSP LATA a E E 9 4 1 PixelDRIVE 3000 Software for the Hexagonal Array occoooccncncnncnocnnoncnnnonccnnnncnnoncnnonncnnoncnnnnnss 9 A is AA e IN 11 A2 iia o co PAP o ai iE Aea iE 11 4 1 3 On Screen Pixel Array ccccccccssscccsesccesecccnscceescccsuseceecensusceueesensuseesesensuseeneesens 12 4 1 4 Temperature Control coooccccnncnncncnnnnncnnononnnoncnnonnnnnonnononnnnnonnnnonnnnnonnnnnnnnnnonnnnnnnioss 12 4 1 5 Single Pixel Select Control coooncccoocnnnnocnnonccnonocnnonconononnnonnnnonnnnnonnnnnnnnnnonnnnnnnioss 12 4 1 6 Pattern GeneratlON ooccccoooccnnnnoccnnnncnnnnnccnnnnronnnnnrrnnnnnnrn nono rn nnnnnrnrrnnrnnnnnnrnnonnnanonanss 12 4 1 7 Pattern AdjUStMEDt ooocccoocnnnnccnnnncnnononnnoncnnonnnnnonnnnonnnnnnnnnnnnnnnnonnnnnnnnnnonnnnnnnnnnennnnnnnnoss 12 5 User Development with LabVIEW VP s Provided by Meadowlark Optics Inc sscccssssseoees 13 6 Care and Maintenance of the SLM Optics c cccsssscsssscssssccssescssssscnsssocssssccsssovessscssssocessconsssooesssonsssocess 13 T Frequently Asked JUCSUONS gisszescccecissauiet
18. dient across the pixel array The angle specifies the direction of the gradient the gradient value specifies the spatial rate of variation across the array and the offset uniformly adjusts the pixel values e POLY r Applies a radially symmetric polynomial function up to third order The r r r andr coefficients can be entered A small plot of pixel value vs ris displayed e SINE r Applies a radially symmetric sinusoidal function A is the O peak amplitude dA is the pixel value offset R is the radial period and dR is the radial offset A small plot of pixel value vs r is displayed e SINC r Applies a radially symmetric sinc sin r r function A is the 0 peak amplitude dA is the pixel value offset R is the radial period and dR is the radial offset A small plot of pixel value vs r is displayed e AIRY r Applies a radially symmetric Airy disk function A is the peak amplitude dA is the pixel value offset W is the width and dR is the radial offset A small plot of pixel value vs r is displayed e GAUSS r Applies a radially symmetric Gaussian function A is the peak amplitude dA is the pixel value offset W is the width and dR is the radial offset A small plot of pixel value vs r is displayed e RANDOM Randomly calculates a value between the specified upper and lower limits for each pixel meadoulark optics D3128 User s Manual rev 1 04 7 polarization solutions 3 1 4 Hex Pattern Adjust
19. ed in Fig 5 clicking the Meadowlark Optics logo displays software and firmware version information meadoulark optics D3128 User s Manual rev 1 04 5 polarization solutions Es PixelDRIVE 3000 Ea meadowlark 2ptics PIXELDRIVE 3000 Es SO Tio iat MoOoULaATOR INTERFACE Main Functions Configure Live TEF cyae a E Frame Frames er Open Save 10 i rrame Contro ex Pattern Generation vau Uniform Linear Horiz Vert ET Pixel Value H w mma Hex Pattern Adjust C zetRescale Add Noise DC Adjust Rescale pum fma EA Figure 5 Sectioned PixelDRIVE 3000 Hex Interface 1 Main functions 2 Frame control 3 Hex pattern generation 4 Hex pattern adjustment 5 Temperature control 6 Pixel control display 3 1 1 Main Functions CONFIGURE LIVE In LIVE mode changes made to the on screen pixel array are immediately relayed to the SLM hardware In the CONFIGURE mode changes will not be updated until either LOAD FRAME or CYCLE FRAMES is pressed LOAD FRAME Loads the current on screen pixel array to the SLM hardware CYCLE FRAMES Activates frame cycling loading each frame in sequence to the SLM hardware for the specified duration When frame cycling is activated a small window replaces the main user interface indicating cycling progress and allowing the user to cease frame cycling ONCE REPEAT Controls whether the CYCLE FRAMES control will load the frame sequence only once or repeat the
20. esstusccacacusacus saunecusbcuseneceueacusecesccastaucececenuncessaeusncuseseseasbeusenusens 13 Appendix A Pixel Data File Formats scsscsscscssscscccisccusecestenccavsccacendesausesusdcaseenstencocesescsssesteutatessieasasbensatessas 15 Appendix B Firmware Updater scccesscccccnsececescceccetsacecessccceiestascedscucseecectescecoacsecocccdshcedstusececensetccdecwescucnessess 17 Appendix Ce SOM Ware icensini sosisini aaa S Sa ENaren 21 Software License Agreement wax ptcoasccierencaciGeesietie doncasatriatatierentaneket A pA DT ACTA a e ccc tie tnt o PUE Po A 23 meadoulark optics D3128 User s Manual rev 1 04 111 polarization solutions Information in this document is subject to change without notice Meadowlark Optics may have patents patent applications trademarks copyrights or other intellectual property rights covering subject matter in this document Except as expressly provided in any written license agreement from Meadowlark Optics the furnishing of this document does not give you any license to these patents trademarks copyrights or other intellectual property Please contact Meadowlark Optics for a list of applicable patents trademarks and or copyrights Copyright O 2010 Meadowlark Optics Incorporated All rights reserved Printed in the United States of America meadoulark optics D3128 User s Manual rev 1 04 1V polarization solutions D3128 Spatial Light Modulator The D3128 from Meadowlark Optics Inc is a complete
21. f receipt of this agreement and shall remain in full force until terminated Without prejudice to any other right Licensor may terminate this agreement if you fail to comply with any of the terms and conditions of this license agreement b Procedure upon Termination Within ten 10 days after termination of this Agreement Licensee will return to Licensor at Licensee s expense the Software and all copies thereof delete or destroy all other copies of the Software and deliver to Licensor a certification signed by an meadoulark optics D3128 User s Manual rev 1 04 22 polarization solutions 10 11 12 13 14 15 officer of Licensee that the Software has been returned all copies deleted or destroyed and its use discontinued Force Majeure If performance hereunder other than payment 1s interfered with by any condition beyond a party s reasonable control including any Act of God the affected party shall be excused from such performance to the extent of such condition However 1f a force majeure detrimentally affects a party s performance of a material obligation hereunder for 14 days or more the other party can terminate this Agreement Mediation Arbitration The parties shall endeavor to resolve any dispute by mediation in Boulder CO under the CPR Mediation Procedure If the parties have not resolved this matter within 45 days from the selection of a mediator the parties shall settle any controversy ar
22. greement may be changed only by a writing signed by both parties The waiver of a breach of any provision of this Agreement will not operate or be interpreted as a waiver of any other or subsequent breach Severability Headings If any provision herein is held to be invalid or unenforceable for any reason the remaining provisions will continue in full force without being impaired or invalidated in any way The parties agree to replace any invalid provision with a valid provision that most closely approximates the intent and economic effect of the invalid provision Headings are for reference purposes only and in no way define limit construe or describe the scope or extent of such section Governing Law This Agreement will be governed and construed in accordance with the laws of the State of Colorado without giving effect to conflict of laws principles Both parties submit to personal jurisdiction in Colorado Trademarks National Instruments LabVIEW and NI VISA are trademarks of National Instruments Corporation Microsoft Windows and MS DOS are registered trademarks of Microsoft Corporation Pentium is a registered trademark of Intel Corporation All other copyrights cited in this document are the property of their respective owners meadoulark optics D3128 User s Manual rev 1 04 23 polarization solutions
23. he coordinate system and illustrates the restriction that valid coordinate pairs must be odd odd or even even Fig 6 shows highlighted pixels at x y 0 0 and at x y 1 3 as examples of valid pixel index coordinate pairs A counterexample at x y 3 6 shows an invalid coordinate pair Fig 6 also shows the index limits of 6 lt x lt 6 and 12 lt y lt 12 de HAS KT N Da a e j 0008 LAE RD J p m VA UVA DY E ARE RIA 2 A 4 4 Wie O e mn lo 7 8 WX ere Ts an tee LA h 9990 Wate a ey wt 6 5 4 3 2 1 O0 1 2 3 4 5 6 Figure 6 Hexagonal Pixel Array Indexing Valid pixel coordinate indices are exemplified at x y 0 0 and 1 3 while an invalid pixel coordinate pair is exemplified at x y 3 6 meadoulark optics D3128 User s Manual rev 1 04 8 polarization solutions The pixel indexing convention results in a 43 1 geometric aspect ratio as shown in Fig 7 In order to adapt an analytical function of x and y the y variables appearing in the analytical form must be divided by V3 or x variables must be multiplied by V3 to achieve proper symmetric rendering on the pixel array A oemei m 0 V 3 Dal 1 Figure 7 Pixel Indexing Aspect Ratio 4 Linear 128 Pixel Array Two available D3128 optical configurations are the 127 pixel hexagonal array and the 128 pixel linear array Both optical configurations include software that has been customized to the geometr
24. icensor may provide Licensee with support services related to the Software Use of Support services is governed by the Licensor policies and programs described in the Service Level Agreement Any supplemental software code modifications or enhancements provided to meadoulark optics D3128 User s Manual rev 1 04 21 polarization solutions you as part of the Support service shall be considered part of the Software and subject to the terms of this License Agreement 4 Ownership a Title Licensee and Licensor agree that Licensor owns all proprietary rights including patent copyright trade secret trademark and other proprietary rights in and to the Software and any bug fixes enhancements updates or other modifications including custom modifications to the Software whether made by Licensor or any third party b Transfers Under no circumstances shall Licensee sell license publish display distribute or otherwise transfer to a third party the Software or any copy thereof in whole or in part without Licensor s prior written consent 5 Limited Warranty Support Services a Scope of Warranty Licensor warrants for a period of one year from the date of receipt of the Software against faulty workmanship or the use of defective materials and that such Software will conform to Licensor s accompanying written specifications This limited warranty shall be void in the event of failure from accident abuse or misapplication b Disclai
25. ilt with National Instruments LabVIEW Application Builder b Restrictions on Use Licensee agrees to use the Software only for Licensee s own business Licensee shall not 1 permit any parent subsidiaries affiliated entities or third parties to use the Software 11 process or permit to be processed the data of any other party 111 use the Software in the operation of a service bureau or iv allow access to the Software through any terminals located outside of Licensee s Site c Copies Licensee solely to enable it to use the Software may make one archival copy of the Software computer program provided that the copy shall include Licensor s copyright and any other propriety notices The Software delivered by Licensor to Licensee and the archival copy shall be stored at Licensee s Site d Modifications Reverse Engineering Licensee agrees that only Licensor shall have the right to alter maintain enhance or otherwise modify the Software Licensee shall not disassemble decompile or reverse engineer the Software e Material Terms and Conditions Licensee specifically agrees that the terms and Conditions of this Section 2 are material and that failure of Licensee to comply with these terms and conditions shall constitute sufficient cause to terminate this Agreement 3 Data Conversion Support a Data Conversion Licensee shall be solely responsible for data conversion data entry and verification of data b Support L
26. inear Interface 1 Main functions 2 Frame control 3 Pixel control display 4 Temperature control 5 Single pixel select control 6 Linear pattern generation 7 Linear pattern adjustment 4 1 1 Main Functions USB DEVICE Selects among several Meadowlark Optics USB devices when several Meadowlark Optics USB devices are connected to the PC CONFIGURE LIVE In LIVE mode changes made to the on screen pixel array are immediately relayed to the SLM hardware In the CONFIGURE mode changes will not be updated until either LOAD FRAME or CYCLE FRAMES 1s pressed LOAD FRAME Loads the current on screen pixel array to the SLM hardware CYCLE FRAMES Activates frame cycling loading each frame in sequence to the SLM hardware for the specified duration When frame cycling is activated a small window replaces the main user interface indicating cycling progress and allowing the user to cease frame cycling ONCE REPEAT Controls whether the CYCLE FRAMES control will load the frame sequence only once or repeat the sequence until the user deactivates frame cycling PATTERN DEFAULTS Resets the default values for the selected pixel pattern see Section 4 1 6 for a discussion of pattern generation OPEN FILE Reads frame and pixel array configuration data from an ASCII text file see Appendix A for the file specification SAVE FILE Writes the current frame and pixel array configuration to an ASCII text file see Appendix A for the file specificati
27. ising out of this Agreement by arbitration to be held in Boulder Colorado in accordance with the rules of the American Arbitration Association A single arbitrator shall be agree upon by the parties or 1f the parties cannot agree upon an arbitrator within thirty 30 days then the parties agree that a single arbitrator shall be appointed by the American Arbitration Association The arbitrator will apply the substantive law of the State of Colorado The arbitrator may award attorney s fees and costs as part of the award The award of the arbitrator shall be binding and may be entered as a judgment in any court of competent jurisdiction Notices Any notice under this Agreement will be in writing and delivered by personal delivery overnight courier confirmed facsimile confirmed e mail or certified or registered mail return receipt requested and will be deemed given upon personal delivery 1 day after deposit with an overnight courier 5 days after deposit in the mail or upon confirmation of receipt of facsimile or email Notices will be sent to a party at its address set forth at the end of this Agreement or such other address as a party may specify in writing pursuant to this Section Entire Agreement Amendment Waiver This Agreement sets forth the entire understanding and agreement of the parties and supersedes any and all oral or written agreements or understandings between the parties as to the subject matter of the Agreement This A
28. izontal amounts e SCALE o MULTIPLIER A factor by which each pixel will be scaled o APPLY Rescales the pixel array e NOISE o NEGATIVE The maximum value that would be subtracted from each pixel o POSITIVE The maximum value that would be added to each pixel e APPLY Adjusts each pixel by a random amount bounded by the Negative and Positive limits meadoulark optics D3128 User s Manual rev 1 04 12 polarization solutions 5 User Development with LabVIEW VPs Provided by Meadowlark Optics Inc Several VI s are included in a library file on the PixelDRIVE 3000 CD They can be found in lt drive letter gt LabVIEW directory LabVIEW VI s that interface with the D3128 are e Meadowlark Hex SLM User Example VI e Meadowlark Linear SLM User Example VI e Meadowlark Hex SLM User VT s LLB o Meadowlark Load Hex Array VI Meadowlark Load Linear Array VI Meadowlark USB Com VI Meadowlark USB Easy Close VI Meadowlark USB Easy Open VI Meadowlark USB Read Temperature VI Meadowlark USB Set Temperature VI O O O OOO The user development directory includes a LabVIEW library file containing fundamental VT s and examples that implement them in rudimentary programs that set the hexagonal and linear voltage arrays The LabVIEW back panels of the hex and linear example VI s have been made accessible to our customers to facilitate independent development Developers are encouraged to open and examine the example VI diagram screens
29. mer of Any Other Warranty THE LIMITED WARRANTY SET FORTH IN SUBSECTION 5 a IS IN LIEU OF ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 6 No Consequential Damages NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR INDIRECT SPECIAL INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION LOST PROFITS RELATED TO THIS AGREEMENT OR RESULTING FROM LICENSEE S USE OR INABILITY TO USE THE SOFTWARE ARISING FROM ANY CAUSE OF ACTION WHATSOEVER INCLUDING CONTRACT WARRANTY STRICT LIABILITY OR NEGLIGENCE EVEN IF THAT PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES 7 Limitation on Recovery Under no circumstances shall the liability of Licensor to Licensee exceed the amounts paid by Licensee to Licensor under this Agreement 8 Indemnity Licensor shall indemnify and hold harmless Licensee from and against any claims based on infringement of any United States copyright or patent by the Software Licensee agrees to cooperate fully with Licensor during such proceedings Licensor shall defend and settle at its sole expense all proceedings arising out of the foregoing In the event of such infringement Licensor may replace in whole or in part the Software with a substantially equivalent computer program or modify the Software to avoid the infringement 9 Term and Termination a Term This license agreement is effective from the date o
30. on RESET Performs a soft reboot of the D3128 controller and re enumerates the USB connection EXIT Quit PixelDRIVE 3000 4 1 2 Frame Control FRAME SELECTOR slider and numeric control Selects a pixel array from the sequence and renders it on the display ADD FRAME Adds a new frame to the sequence after the current frame DELETE FRAME Removes the current frame from the sequence DURATION MSEC Specifies the duration time in milliseconds of the current frame APPLY TO ALL Sets the duration time of all frames to that of the current frame meadoulark optics D3128 User s Manual rev 1 04 11 polarization solutions 4 1 3 On Screen Pixel Array e Shows graphically the voltage settings of each pixel vertical vs the pixel index number horizontal e Clicking a pixel highlights it yellow as the selected pixel e Clicking and sliding a pixel vertically varies its value 4 1 4 Temperature Control e STATUS LED illuminates green when the SLM temperature is within 1 C of the setpoint e UPDATE LED blinks when the SLM temperature is measured e SETPOINT C Sets the desired operating temperature of the SLM e TEMP C Shows the current measured temperature of the SLM updated automatically at 5 sec intervals Note that automatic temperature measurement is disabled when frame cycling is active 4 1 5 Single Pixel Select Control Includes pixel select and pixel level controls to precisely set the voltage of a specific pixel
31. osen file Extreme caution should be exercised when deciding whether to program the D3128 with a file that may not be compatible If there are questions about choosing the appropriate file please contact Meadowlark Optics at 303 833 4333 Meadowlark Optics Firmware Updater A meadowlark optics Firmware rasin nn x a WARNING Specified hex file is For a product File Nal other than the controller that is to be programmed d3126_305 Continue Choose a different File Do Not While Programming meadoulark optics D3128 User s Manual rev 1 04 18 polarization solutions 6 After the hex file is loaded and passes the validity tests the ready screen appears as below Code Size shows the size of the firmware code and is present only for troubleshooting Click the Program button to reprogram the D3128 firmware If a final check is desired before reprogramming firmware the Meadowlark Optics logo may be clicked to display a screen shown below showing the old and new firmware versions TEN Optics Firmware Updater x meadouwlark aptics Firmware Updater Erasing Programming File Name Code Size d3126 305 hex WARNING Do Not Disturb Power to the Controller While Programming Meadowlark Optics Firmware Updater med LA Firmware Updater Info eae Meadowlark Optics File Version 1 0 e2004 Meadowlark Optics All Rights Reserved Existing Firmware Mew Firmware 3 05 3 05 Do d3128 meadoulark
32. r programming Do Not Disturb Power to the Controller While Programming 3 Cycle power on the D3128 controller to ensure the USB connection is properly made After the front panel status LED is done flashing wait at least 2 seconds before clicking OK If the power is not cycled or the OK button is clicked too soon the following error will be displayed If this error appears close the firmware updater program and re run it E Meadowlark Optics Firmware Up ESO al T x meadowlark optics Firmware DH O O Era 9 A LabVIEW An exception occurred within the external i code called by a Call Library Mode This might hawe corrupted LabWIEW s memory Save any work bo a mew File location and restart LabWIEW WI loader vi was stopped at node Ox1046 of subyI loader vi meadoulark optics D3128 User s Manual rev 1 04 17 polarization solutions 4 The following screen will appear after the USB connection is made ES Meadowlark Optics Firmware Updater Choose Hex File 2 d3128_305 hex History Desktop EN My Documents A My Computer ES tl File name a3128_305 y My Network P MN Files of type Custom Pattern d _ hex y A 5 Choose the new hex file and click OK The program will check 1f the new firmware file is valid for the D3128 1f not the following error screen will appear At this point the user may elect to choose a different file or go ahead and program the D3128 with the ch
33. rush the SLM optics Frequently Asked Questions The controller is not working Check that the power supply is plugged in front panel switch is on and the green power light is steady Check the status of the D3128 under Windows Device Manager Occasionally it helps to reboot the controller turn off the controller wait a few seconds then turn 1t back on Then click the RESET button on the PixelDRIVE 3000 user interface ZEN Why might the SLM pause or freeze when I run very fast frame updates frame durations 10 ms High speed frame cycling can experience software conflicts with other USB devices network activity and other applications e g anti virus software If the system hangs during high speed frame cycling it is recommended that the host PC be removed from any network that all other applications be closed and that any other peripheral devices especially those connected to USB ports be removed PQ Q Are there Apple Linux OS 2 or UNIX versions of PixelDRIVE 3000 Can I use PixelDRIVE 3000 on a PC running MS DOS Windows 3 1 Windows 95 or Windows NT A No PixelDRIVE 3000 runs under the 98SE ME 2000 and XP versions of Microsoft Windows only meadoulark optics D3128 User s Manual rev 1 04 13 polarization solutions PQ PQ PQ PQ PQ Can I write a program in C FORTRAN or Pascal that will talk to the D3128 Meadowlark Optics Inc presently supports only LabVIEW software
34. s The file format is illustrated in Fig 10 Each row must contain data for a unique pixel 1 e the x y indices of each row must not be repeated in a different row For hexagonal SLM data files the order in which the pixels appear 1s not important they will be sorted by the x y coordinates when PixelDRIVE 3000 reads the file Columns represent frames and must be tab delimited and the PixelDRIVE 3000 frame sequence order is determined by the order in which columns appear in the data file A voltage surface function V x y can be evaluated to produce pixel values In calculating analytical functions 1t should be noted that the pixel indexing convention results in a 43 1 aspect ratio In other words in order to adapt an analytical function of x and y the y variables appearing in the analytical form must be divided by V3 or x variables must be multiplied by V3 to achieve proper symmetric rendering on the pixel array S S N S E S A Ka SE r amp SK Q lt O O OS we Oy os SC LS G S L y Hex 1 02 3 00 3 128 06 04 2004 23 25 00 Frame x y 0 100000 0 400000 0 350000 lt Durations sec 0 000000 12 000000 1 000000 2 000000 3 000000 lt Pivel 0 12 Values 0 000000 10 000000 1 000000 2 000000 3 000000 lt Pivel 0 10 Values 0 000000 8 000000 1 000000 2 000000 3 000000 lt Pixel 0 8 Values 0 000000 12 00000 1 000000 2 000000 3 000000 lt Pivel 0 12 Values 12 000000 12 00000 1 000000 2 000
35. spatial a SR light modulator D3128 Spatial Light Modulator User s Manual Revision 1 04 meadoulark optics polarization solutions D3128 Spatial Light Modulator Quick Setup Guide 1 Install the PixelDRIVE 3000 software on a PC running Microsoft Windows 98SE or later Place the included CD in the CD ROM drive Wait for the PixelDRIVE menu to appear then click on the Install PixelDRIVE button 2 Connect the D3128 control module USB connector to a PC USB port using the included USB cable 3 With the SEM optics head positioned as desired connect the optics head to the control module using the included 25 pin cable 4 Plug the power supply cable into the power connector on the D3128 control module Connect the power supply to a properly grounded outlet 5 If array updates are to be synchronized to other experiment equipment connect the TRIGGER output SMB terminal to the high impedance trigger input of other laboratory devices 6 Power on the D3128 control module The POWER light will illuminate and the STATUS light will blink the firmware version during initialization After initialization the STATUS light will go off The POWER light remains illuminated until the power is turned off 7 The first time the unit is powered on Windows will detect new hardware and prompt for a driver The driver files are on the PixelDRIVE 3000 CD For Windows 2000 and Windows XP drivers are in the USB DRI
36. temperature setpoint initializes to 35 C What is the purpose of the extra pixel control in the hexagonal pixel array This controls the test pixel which is a large uniformly driven region of the SLM optic outside of the patterned hexagonal pixel array Meadowlark Optics Incorporated P O Box 1000 Frederick Colorado 80530 303 833 4333 www meadowlark com sales meadowlark com meadoulark optics D3128 User s Manual rev 1 04 14 polarization solutions Appendix A Pixel Data File Formats PixelDRIVE 3000 offers a feature for saving and loading pixel configurations as ASCU text data files The first row of a Pixel data file is a space delimited header line that includes the type of SLM PixelDRIVE 3000 software version number D3128 firmware version number number of frames number of pixels and the date and time the file was generated When a pixel data file is opened with PixelDRIVE 3000 the SLM identifier must match the hardware configuration of the SLM e g Hex for the Hex SLM and Linear for the Linear SLM The remainder of the file includes tab delimited columns of pixel values that differ depending on the type of SLM hexagonal or linear A 1 File Format for the Hexagonal Array SLM The second row is tab delimited and contains header characters x and y followed by frame duration times in seconds The 128 remaining rows are tab delimited and consist of x pixel indices y pixel indices and pixel value
37. with a subtractive fixed polymer retarder called a compensator attached to the liquid crystal cell Negative retardance values are sometimes preferred for example when converting between right and left circularly polarized states Fig 2 illustrates retardance as a function of voltage for a typical LCVR with and without an attached compensator Placing a compensated LCVR between two high extinction polarizers creates an excellent optical attenuator with convenient electronic control 0 75 0 50 0 25 Retardance waves 0 00 a 0 3 10 15 20 Voltage volts RMS 0 75 0 50 0 25 Retardance waves 0 00 b 0 5 10 15 20 Voltage volts RMS Figure 2 Liquid Crystal Variable Retarder performance at 632 8 nm 21 C a without compensator and b with compensator As with any birefringent material retardance is dependent upon thickness and birefringence Liquid crystal material birefringence depends on operating wavelength drive voltage and temperature The overall retardance of a liquid crystal cell decreases with increasing temperature approximately 0 4 per C Liquid crystal devices should be electrically driven with an AC waveform with no DC components to prevent ionic buildup which can damage the liquid crystal layer LCVR s from Meadowlark Optics for instance require a 2 kHz square wave with a zero average voltage Retardance is controlled by varying the peak to peak voltage from zero to 10V meadoul
38. xel 16 bit color graphics a CD ROM and Microsoft Windows 2000 or XP 2 2 Setup Procedure for the D3128 1 Unpack controller and cables from shipping container Please verify that your shipment included D3128 controller unit 1 SLM optical head unit 1 25 conductor optical head cable 1 12V power supply and power cable 1 unit with 12V cable attached and 1 AC power cable USB cable 1 PixelDRIVE 3000 software CD 1 User s manual 1 printed copy 2 Hardware configuration of the D3128 control module Position the SLM optical head securely on an optics table or breadboard The optical head has two 8 32 tapped holes on all four edges as well as 14 20 tapped holes on two edges for mounting the SLM optical head with standard optics hardware Connect the 25 pin optical head cable to the optical head The optical head connector is keyed to disallow improper insertion Connect the other end of the optical head connector to the D3128 control module Connect the 12VDC supply to the D3128 control module Plug the power supply into a properly grounded AC outlet Attach the USB cable to the USB connector on the rear of the D3128 control module and connect the other end to an available USB port on a PC If synchronizing array updates to other experiment equipment connect the TRIGGER output SMB terminal to the high impedance trigger input of other laboratory devices meadoulark optics D3128 User s Manual rev 1 04 3 polari
39. y of the pixel array The software that drives the linear array is detailed here please refer to Section 3 for a discussion of the software that drives the linear array 4 1 PixelDRIVE 3000 Software for the Linear Array The D3128 includes PixelDRIVE 3000 a user friendly software interface for control of the spatial light modulator Here we detail the functions of PixelDRIVE 3000 Also included on the CD are LabVIEW VI s compatible with National Instruments LabVIEW versions 6 1 or later that end users can include in their own development efforts Voltage levels here refer to the amplitude envelope about a 2 kHz square wave with zero DC offset Never apply a voltage with a non zero DC component to a liquid crystal cell As voltage levels are mentioned in the present context it is important to bear in mind that we are describing the amplitude envelope about a 2 kHz square wave For instance a driver signal described as invariant actually refers to a square wave with a steady amplitude the envelope is unchanging in time but the signal itself if measured with an oscilloscope for instance oscillates about the zero voltage axis It 1s important to note that the square wave is always symmetric about the zero voltage axis As previously mentioned zero offset is critical for nematic liquid crystal cells meadoulark optics D3128 User s Manual rev 1 04 9 polarization solutions Es PixelDRIVE 3000 meadowlark 2ptics PIXEL
40. zation solutions meadoulark ptics PAIAL IULATOR D3128 haldid Figure 3 Spatial Light Modulator Components 1 SLM optical head 2 Optical head cable 3 D3128 Controller 4 USB cable 5 Power supply 6 PC running PixelDRIVE 3000 3 Turn on the front panel switch and observe the LED s The green power LED remains illuminated as long as the unit is powered on The yellow status LED blinks the D3128 s firmware version as the D3128 control module performs a power on self test then goes off During the power on self test the entire pixel array will be driven to maximum voltage for 500 ms reduced to half voltage for 500 ms then reduced to zero upon completion of the power on self test 4 The first time the D3128 is powered on Windows will detect a new USB device upon completion of the power on self test For installation to a PC running Windows 2000 Windows XP or Windows Vista direct Windows to look in the USB Drivers Win2K_XP directory on the CD For installation to a PC running Windows 98SE or Windows ME specify the USB Drivers Win98_ME directory Note Windows may say that the driver has not passed certification press continue anyway The drivers have been extensively tested 5 Install the PixelDRIVE 3000 software by first placing the PixelDRIVE CD in the CD ROM drive Then wait for the PixelDRIVE menu to appear and click on the Install PixelDRIVE button If the menu does not appear
Download Pdf Manuals
Related Search