TDS12.. - Amazon Web Services
Contents
1. clear light Steam setting selection button Steam setting indicator lamps green eco red max Shot of steam button Spray button Water inlet Water inlet lid Spray nozzle 11 Water tank 12 Level mark for maximum filling 13 Soleplate 14 Temperature index 15 Temperature control 16 Power cable 17 Descaling fluid 18 Fabric protection soleplate cover Model dependent Ni oND o Before using the iron for the first time Remove any labels or protective covering from the soleplate 13 For further details on the following actions please refer to the related chapters in this user manual With the iron unplugged fill the tank 11 of the iron with tap water and set the temperature control 15 to max Plug in the appliance to the mains When the iron has reached the desired temperature the green light 5 stops flashing and the clear light 3 starts flashing Grip the handle 1 and set the steam control to the maximum position max see setting the steam amount section Hold the iron horizontally and repeatedly press the shot of steam button 6 Some residue may come out of the soleplate 13 If necessary carefully clean the soleplate 13 down with a dry folded cotton cloth When using the steam function for the first time do not use it on your laundry as there may still be dirt in the steam dispenser When turned on for the first time your new iron2. as secondary raw materials Your local town council can give you information about how to dispose of obsolete appliances This appliance is labelled in accordance with European Directive 2002 96 EU concerning used electrical and electronic appliances waste electrical and electronic MIA equipment WEEE The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU Guarantee conditions The terms of the guarantee for this appliance are in accordance with that stated by our representative for the country in which it is sold The details of these conditions can be obtained from the retailer from whom the appliance was purchased The purchase receipt must be presented when making any claims against the terms of this guarantee Bosch ES Trouble shooting The iron does not 1 heat up ActiveControl Advanced indicator lamp 3 flashes Iron difficult to slide on the clothing The clothes tend to stick Water drips out of the 1 soleplate together with steam Steam does not come out ND D Spray does not work 1 Temperature control 15 set to minimum 2 No mains supply 3 The SensorSteam system has been activated The iron is set to stand by The SensorSteam system has been activated The iron is set to stand by Clothing is too wet The temperature is too high Temperature control 15 setting is t
3. cancel continuous steam generation while gripping the handle 1 On this setting steam can only be produced when manually pressing the steam activation button 2 under the handle Press the steam activation button 2 Important e Steam is only available if the temperature control 15 is set at the steam symbols gt R between se and max Adjust the temperature setting and then set the steam control according to the table below Steam will automatically be produced Temperature control 15 setting eco Steam setting eee to max max Note Once a steam ironing setting has been chosen using the temperature control 15 steam generation may be delayed for several seconds until the appropriate working temperature has been reached 4 ES 1 Ironing without steam This enables the iron to be used for dry ironing Grip the handle 1 and set the steam control to the XX setting The temperature control 15 adjusts the temperature of the soleplate 13 Set it to the corresponding position by lining it up with the temperature index 14 on the iron Select an appropriate temperature for the type of material being ironed see setting the temperature section While ironing do not press the steam activation button 2 Spray This can be used to remove stubborn wrinkles Do not use the spray function with silk as staining may occur When ironing press the
4. may smell and emit a little smoke and a few particles this will stop after a few minutes BOSCH Filling the water tank Unplug the iron from the mains Open the water inlet lid 9 Never fill beyond the level mark for maximum filling 12 Use only clean water from the tap without mixing anything with it The addition of other liquids unless recommended by Bosch such as perfume will damage the appliance Any damage caused by the use of the aforementioned products will make the guarantee void Do not use condensation water from tumble dryers air conditioning systems or similar This appliance has been designed to use normal tap water To prolong the optimum steam function you may mix tap water with distilled water 1 1 If the tap water in your district is very hard mix tap water with distilled water 1 2 You can inquire about the water hardness with your local water supplier The temperature control 15 adjusts the temperature of the soleplate 13 Check the temperature instructions shown on the care label of the garment you are ironing Set the temperature control 15 to the corresponding position by lining it up with the temperature index 14 on the iron Setting the temperature Synthetics eo Silk Wool eco Cotton Linen Sort your garments based on their care labels always starting with clothes that have to be ironed at the lowest temperature If you are unsure what type of material the g
5. range of irons is equipped with the following de scaling features AntiCalc 1 self clean The self clean filter between the water tank and the pump prevents scale impairing the steam generation system and ensures the optimum production of steam 2 anti calc The anti calc cartridge has been designed to reduce the build up of scale produced during steam ironing helping to extend the useful life of your iron Nevertheless the anti calc cartridge cannot prevent all of the scale that is produced naturally over time 3 calc n clean The calc n clean function helps to remove scale particles out of the steam chamber Use this function approximately every 2 weeks if the water in your area is very hard Follow the procedure described below a Remove the plug from the socket ensure that the iron has cooled down and that the water tank 11 is empty b Set the temperature control 15 to the calc n clean setting 2 ORTO sosch 44 c Fill the water tank 11 to the maximum level with clean tap water d Plug in the iron and select the maximum steam setting max by pressing the steam selection button 4 e Hold the iron over a sink or a container to collect the water f Grip the handle 1 until the water tank 11 is empty This could take several minutes 9 Repeat the procedure until particles no longer come out of the soleplate 13 of the iron h Turn the temperature contr
6. TDS12 SensorSteam Operating instructions BOSCH Model dependent BOSCH 44 Index Description Before using the ron for the first time Filling the water tank Setting the temperature Setting the steam amount SensorSteam Ironing with steam Ironing without steam Spray Shot of steam Vertical steam Multiple descaling system Anti drip system Fabric protection soleplate cover Cleaning amp Maintenance Storing the appliance Tips to help you save energy Advice on disposal Guarantee conditions Trouble shooting 44 Thank you for buying the TDS12 steam iron from Bosch This iron is a compact steam generator The water is pumped into the steam chamber with pressure via a special pump The steam amount when ironing is higher than in conventional irons therefore the steaming performance is far more effective Please visit www bosch home co uk for more product information or to register your product just follow the link to the Online guarantee registration Introduction This powerful system produces continuous steam for an ideal ironing performance It has a large water tank that can be refilled at any time without switching off the system We hope that you enjoy ironing with this steam station Important Please read these instructions for use carefully before using the appliance and save them for future reference This appliance complies with international safety standards
7. This appliance has been designed exclusively for domestic use and must not be used for industrial purposes General safety instructions The iron must not be left unattended while it is connected to the supply mains Remove the plug from the socket before filling the appliance with water or before pouring out the remaining water after use stand is placed is stable The appliance must be used and placed on a stable surface When placed on its stand make sure that the surface on which the The iron should not be used if it has been dropped if there are visible signs of damage or if it is leaking water It must be checked by an authorized Technical Service Centre before it can be used again With the aim of avoiding dangerous situations any work or repair that the appliance may need e g replacing a faulty mains cable must only be carried out by qualified personnel from an Authorised Technical Service Centre This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Keep the iron and its cord out of reach of children less than 8 years of age when it is
8. arment is made from start ironing on the lowest temperature setting and increase accordingly If the garment is made from mixed fabrics set the temperature for the most delicate material For silk woollen or synthetic materials iron the reverse side of the fabric to prevent shiny patches Avoid using the spray function to prevent stains MS osch 44 3 Setting the steam amount Your iron is equipped with a steam setting selection button 4 and indicator lamps 5 showing the steam setting according to the table below Steam eco max cal selling steam off p EEE Es Indicator En lamps Green Red Off Steam can be generated by gripping the handle 1 or by pressing the steam activation button 2 If the eco steam mode is selected the energy consumption of the appliance will be reduced by means of reduction of electricity and water consumption good ironing result can be obtained on this setting for most garments The steam setting can be changed by pressing the steam setting selection button 4 The iron runs through the following cycle i eco max steam sl The SensorSteam function automatically switches off the iron when the handle is no longer gripped thus increasing safety and energy saving When plugging the iron in during the first minute The soleplate 13 heats up to the temperature corresponding to the selected setting The steam generation is blocked The green
9. detergents or solvents otherwise the iron will drip water whilst steaming FE Cleaning amp Il Storing the appliance Open the water inlet lid 9 Hold the iron with the front facing down and shake it gently until the water tank 11 is empty Set the iron aside in a vertical position to cool down Coil the power cable 16 loosely around the heel of the iron before storing Store the iron in an upright position 4 Tips to help you save R energy Steam production consumes the most energy To help minimise the energy used follow the advice below Start by ironing the fabrics that require the lowest ironing temperature Check the recommended ironing temperature in the label on the garment Regulate the steam according to the selected ironing temperature following the instructions in this manual Iron at eco steam setting see setting the steam level section Try to iron the fabrics while they are still damp and reduce the steam setting Steam will be generated from the fabrics rather than the iron If you tumble dry your fabrics before ironing them set the tumble drier on the iron dry programme If the fabrics are damp enough set the steam to the 3 position see ironing without steam section Advice on disposal Our goods come in optimised packaging This basically consists in using non contaminating materials which should be handed over to the local waste disposal service
10. ed indicator lamp 3 on the handle flashes and the pump will not work Fabric protection soleplate cover protect model dependent The fabric protection cover 18 is used for steam ironing delicate garments at maximum temperature without damaging them Use of the protector also does away with the need for a cloth to prevent shine on dark materials It is advisable to first iron a small section on the inside of the garment to see if it is suitable To attach the fabric protector to the iron place the tip of the iron into the end of the fabric protector and press the rear of the protector upward until you hear a click To release the fabric protector pull down on the clip at the rear Maintenance and remove the iron Attention Risk of burns Always unplug the appliance from the mains supply before carrying out any cleaning or maintenance operation on it If the iron is only slightly soiled pull out the plug and allow the soleplate 13 to cool down Wipe the housing and the soleplate with a damp cotton cloth only If the cloth is synthetic it may melt due to the high temperature on the soleplate 13 switch off the steam and rub off any residue immediately with a thickly folded dry cotton cloth To keep the soleplate 13 smooth you should avoid hard contact with metal objects Never use a scouring pad or chemicals to clean the soleplate Never decalcify the tank 11 or treat it with
11. energized or cooling down CAUTION Hot surface Surface is liable to get hot during use BOSCH This appliance is to be connected and used in accordance with the information stated on its characteristics plate This appliance must be connected to an earthed socket If it is absolutely necessary to use an extension cable make sure that it is suitable for 16A and has a socket with an earth connection If the safety fuse fitted in the appliance blows the appliance will be rendered inoperative To restore normal operation the appliance will have to be taken to an authorised Technical Service Centre In order to avoid that under unfavourable mains conditions phenomena like transient voltage drops or lighting fluctuations can happen it is recommended that the iron is connected to a power supply system with a maximum impedance of 0 270 If necessary the user can ask the public power supply company for the system impedance at the interface point The appliance must never be placed directly under the tap to fill the water tank Unplug the appliance from the mains supply after each use or if a fault is suspected The electrical plug must not be removed from the socket by pulling the cable Never immerse the iron in water or any other fluid Do not leave the appliance exposed to weather conditions rain sun frost etc 4 4 Handle with contact sensor Steam activation button ActiveControl Advanced indicator lamp
12. l to a lower setting Wait 5 seconds between each press of the jet of steam button Mix distilled water with tap water as directed in the Filling the water tank section and never add any other products to the water tank unless recommended by Bosch Set the steam control to eco or max position Fill the tank 11 Set to a higher temperature if compatible with the fabric Fill the water tank 11 Contact the Technical Service This is normal and will stop after a few minutes Carry out a cleaning cycle see calc n clean section This is normal If none of the above solves the problem get in touch with an authorised technical service You can download this manual from the local homepages of Bosch BOSCH 44 4 BOSCH Great Britain Bosch Customer Service Grand Union House Old Wolverton Road Milton Keynes MK12 5PT UK 44 0 844 892 8923 IRL 353 0 1450 2655 www bosch home co uk 002 TDS12GB 07 12
13. lamp 5 flashes After the initial 1 minute period eco setting is automatically selected The green lamp 5 stops flashing The ActiveControl Advanced indicator lamp 3 clear light goes on and starts flashing From this moment on when the handle 1 of the iron is gripped or if the steam activation button 2 is pressed at 3 steam setting The ActiveControl Advanced indicator lamp 3 stops flashing The pump starts working and steam is generated automatically If the handle 1 is released Steam generation will stop The ActiveControl Advanced indicator lamp 3 will flash The iron shuts off automatically If the handle is gripped again the iron turns on If the iron remains plugged in and is not used for several minutes After the handle 1 is touched or the steam activation button 2 is pushed again the green light starts flashing e Steam generation will not be possible for several seconds until the appropriate working temperature has been reached The steam control is used to adjust the amount of steam produced when ironing see setting the steam amount section Steam can be generated in two ways 1 Continuous steam generation Grip the handle 1 e Set the steam control to eco or max position 2 Steam on demand only on models equipped with steam activation button Set the steam control to the x position to
14. ol 15 to the maximum setting The iron will begin to emit steam Wait until the water inside the iron has evaporated i Clean the soleplate 13 of the iron 4 calc n clean with descaling fluid model dependent For deep descaling use the descaling fluid 17 supplied This should be carried out every 3 months The descaling fluid 17 can be obtained from our After sales service or from our website Accessory code Name of accessory After sales Online shop 311144 TDZ1101 Follow the procedure described below a Remove the plug from the socket ensure that the iron has cooled down and that the water tank 11 is empty b Set the temperature control 15 to the calc n clean setting c Fill the water tank 11 with tap water mixed with a measure 25 ml of the descaling fluid 17 d Plug in the iron and select the maximum steam setting max by pressing the steam selection button 4 e Hold the iron over a sink or a container to collect the water f Grip the handle 1 until the water tank 11 is empty This could take several minutes g Then follow the procedure described above in section 3 calc n clean until particles no longer come out of the soleplate 13 of the iron Anti drip system If the temperature control 15 is set too low below s the steam is automatically switched off to prevent water from dripping out of the soleplate 13 The ActiveControl Advanc
15. oo low 2 Steam control is set too high in conjunction with a low temperature You have pressed the shot of steam button 6 repeatedly without waiting for 5 seconds between each press Pure distilled water has been used see Filling the water tank section or other products such as fragrant water have been added to the tank Steam control is set to 28s position No water in the tank 11 The temperature is too low Anti drip system is activated No water in the tank 11 2 Obstructed mechanism Smoke comes out when connecting the iron for the first time Deposits come out through the holes in the soleplate The appliance makes a pumping sound This may be caused by the lubrication of some of the internal parts Traces of lime scale are coming out of the steam chamber Water is being pumped into the steam chamber 1 Turn to a higher position 2 Check with another appliance or plug the 3 1 Wh wN iron into a different socket Grip the handle 1 of the iron to re start it Grip the handle 1 of the iron to re start it Reduce the steam amount by selecting eco or XW settings Turn the temperature control 15 down and wait until the iron has cooled down Turn the temperature control 15 to a higher setting between and max and wait until the green steam setting indicator lamp stops flashing Set the steam contro
16. spray button 7 and water will spray out of the spray nozzle 10 onto the garment PN Air Shot of steam This can be used to remove stubborn wrinkles or to press in a sharp crease or pleat It cannot be used on a synthetic setting for delicate items Set the temperature control 15 to the or max position Set the steam control to the max position Press the shot of steam button 6 on the handle repeatedly at intervals of 5 seconds BOSCH ES Vertical steam T hl This can be used to remove creases from hanging clothes curtains etc Warning Do not iron clothing while it is being worn Never spray or aim the steam at persons or animals 1 Set the temperature control 15 to the or max position Models with steam activation button 2 Grip the handle 1 and set the steam control 4 to the max position Or set the steam control to the 3 position and press the steam activation button 2 Models without steam activation button 2 Grip the handle 1 and set the steam control 4 to the max position Hold the iron in an upright position about 15 cm away from the garment being steamed The shot of steam button 6 on the handle may be additionally pressed at intervals of 5 seconds However after 4 shots of steam wait for 10 seconds to allow for continued steam production Multiple descaling system Depending on the model this
Download Pdf Manuals
Related Search