FC10TE Operating Manual - Equalizer International Ltd
Contents
1. the Reation Plate and the lower Reaction Circlip 7 Unscrew and remove complete collet assembly from the nut body 8 Having removed the collet assembly please note the centre dab marks indicating the position of the first collet section Please also note that the collet segments are arranged on the cage such that the external ridges form one continuous thread FCIOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL RETURN SPRINGS RETURN SCREWS E Hei REACTION CIRCLIPS REACTION PLATE EXTERNAL RIDGES CENTRE DAB MARKS PAGE 20 9 Unclip the Collet Retaining Springs and remove the Collet Segments from the Cage 10 Clean all components with rag and WD40 or similar removing any visible dirt or grit paying particular attention to the Collet Segments Cage and Nut Body Smear all mating surfaces with a high performance molybdenum disulphide grease such as Rocol Sapphire Hi Load 2 Inspect all components for wear and damage Replace all worn and damaged components with genuine Equalizer spares 11 Reassemble by reversing steps 1 9 FCIOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL COLLET RETAINING SY SPRING COLLET RETAINING SPRING PAGE 21 8 PARTS LISTS FCIOTE PART LIST dd PART NO DESCRIPTION 01 070001 01 300901 01 750101 01 750201 01 752101 01 752201 01 752301 01 752401 01 752501 01 752502. CAUTI ON The Pull Rod has a long threaded section and a short threaded section The threads on both sections are different The short threaded end of the Pull Rod must be passed through the flanges to mate with the pull nut FCIOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL 3 The Rod washers are slid over the Pull Rod and rotated to allign with the curvature of the flange 4 The Pull Nuts are threaded on to the pull rod FCIOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL 5 FCIOTE tools are slid on to the Pull Rods until the face of the tools are in contact with the back of the flange you will feel hear a clicking as the Primary Ratchet nut slides along the Pull Rod 6 Secondary Ratchet Nuts are then slid up the pull rods untill the nut retaining pins engage in the key holes the FCIOTE s rear plate RETAINING PIN SECONDARY RATCHET NUT FCLOTE HYDRAULIC FLANGE CLOSING TOOL PAGE 10 OPERATOR INSTRUCTION MANUAL PULL ON THE PULL ON THE MAIN BODY TO RELEASE SLEEVE ADVANCE THE TO RETRACT THE NUT NUT ADVANCE RETRACT ON THIS FACE WILL LOCK THE NUT Note The Ratchet Nut is designed to move freely when advanced along the pull rod indicated by the green arrow The nut can only be advanced by gripping on the nut body The nut will lock on to the pull rod when a force is applied to the load face of the
3. 02 02 23 VALVE COVER SCREW 02 02 24 STEEL BALL 02 02 715800 01 SERVICE KI T H 25 STEEL BALL 01 01 26 SPRING END CAP 01 01 27 L P SPRING 01 01 28 O RING 02 02 29 OVERLOAD COVER 01 01 SCREW 30 CAP 02 02 31 OVERLOAD COVER 01 01 SCREW 32 CONE SEAT 01 01 33 CONE 01 01 34 LONG SEPARATOR 01 01 SPRING 715900 01 SERVICE KIT I 35 BASE PLATE 01 01 36 SCREW 02 02 726000 01 SERVICE KIT J 37 VALVE SCREW 01 02 38 BACK UP RING 01 02 39 O RING 01 02 15 RELEASE KNOB 01 02 16 SCREW 01 02 17 COUPLERS 01 02 716100 01 SERVICE KIT K 40 SCREW 04 04 41 SCREW 01 01 18 CHECK BALL 04 04 57 SCREW 01 01 716200 01 SERVICE KIT L 42 GAUGE COUPLER 01 02 MALE 43 GAUGE 01 02 FC1OTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL KIT PUMP ITEM PART DESCRIPTION QUANTITY QUANTITY 716300 01 SERVICE KI T M 44 PORT GAUGE 0 02 ADAPTOR 45 GAUGE COUPLER 0 02 FEMALE 46 COUPLER 01 02 735100 01 SERVICE KIT 47 RESERVOIR 0 0 BLADDER 48 OIL FILTER 0 0 49 O RING 0 0 50 REFILLING PLUG 0 0 735300 01 SERVICE KIT 51 HANDLE 0 0 52 HANDLE GRIP 0 0 53 YOKE 0 0 54 PISTON PIN 0 0 55 YOKE PIN 0 0 56 RETAINING RING 0 0 57 SCREW 0 0 735200 01 SERVICE KIT P 58 SCREW 04 04 59 TAIL BASE 0 0 60 SPRING WASHER 04 04 61 NUT 04 04 ZN bd Nf bd ONAL PAGE 25 9 WEIGHTS AND DIMEN
4. and warnings before starting to operate the Equalizer equipment WARNING To avoid personal injury and possible equipment damage make sure all hydraulic components are rated to a safe working pressure of 700 bar 10 000 psi WARNI NG Do not overload equipment Over loading causes equipment failure and possible personal injury The risk of overloading can be avoided by using the Equalizer Hand Pump which has its safety valve set to 700 bar by the factory If alternative pumps are used ensure they are rated at a safe working pressure of 700 bar 10 000 psi CAUTI ON Make sure that all system compo nents are protected from external sources of damage such as excessive heat flame mov ing machine parts sharp edges and corrosive chemicals CAUTI ON Avoid sharp bends and kinks that will cause severe back up pressure in hoses Bends and kinks lead to premature hose failure Do not drop heavy objects onto hoses A sharp impact may cause internal damage to hose wire strands applying pressure to a damaged hose may cause it to rupture Do not place heavy weights on the hoses or allow vehicles to roll over the hoses crush damage will lead to pre mature hose failure WARNING Immediately replace worn or damaged parts with genuine Equalizer parts Equalizer parts are designed to fit properly and withstand rated loads For repair or maintenance service contact your Equalizer distributor or service centre DANGER To avoid pers
5. nut It is not possible to move the nut untill the load is removed from the load face of the nut The nut can only be retracted by pulling on the release sleeve in the retract direction indicated by the yellow arrow FC1OTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL PAGE 11 7 Rotate the secondary ratchet nuts clockwise 30 degrees to lock them on to the rear plate 8 Check that the release valves on the hand pumps are open by rotating fully anti clockwise and then connect the Pressure gauges to the pump ensuring all the couplers are fully hand tight Ge PRESSURE GAUGE 5505 os HP550D RELEASE VALVE FC10TE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL PAGE 12 9 The Pumps can now be connected to the tools using the Hoses supplied ensure all couplers are fully tightened HP550S HP550D Note Prior to operating the Equalizer Hydraulic Hand Pumps please read 1 the Hydraulic Hand Pump Manuall This is included in all tool kits and is also available for download from www equalizerinternational com 10 Close the release valve on the pump by turning clockwise To commence flange closing gently prime the pump s adjusting the pressure on each tool as neccessary to RELEASE maintain parrallelism between flange faces If the pressure increases to 10 000 PSI with no movement of the flanges then a greater number of tools wil
6. x 10 000 psi 700 bar HP550D Sealed Hand Pump with Gauges 2 x 10 000 psi 700 bar Hydraulic Hose 2m 78 75 1 x Instruction Manual 1 x Carry Case with Protective Foam Inserts Product Code FCLOTEMAX FC10TE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL 4 TECHNICAL DATA FC1OTE TECHNICAL DATA Closing force 10 tonnes per tool It is recommended that tools are used in pairs giving 2 x 10 20 tonnes If using the Equalizer HP350S D Hand Pump or if a hydraulic pressure gauge is fitted the spreading force per tool can be determined by taking a reading from the gauge Gauge pressures will produce spreading forces as set out below ure psi 1000 3000 5000 7000 10000 ee Closing distance 600mm Omm 23 5 0 Can be used on any flange joint with flange bolt holes of 22mm 7 8 or greater Hydraulic oil grade 15 centistokes cSt 40 C tested by ASTM D 445 The 0 has not been designed or certified as lifting equipment If the tool is being used to close flange joints with a Vertical Axis the FC10TE must be used in conjuction with certified lifting equipment FC1LOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL 5 HOW THE FC10TE HYDRAULIC FLANGE CLOSING TOOL WORKS PULL ROD 1 The Pull Rod is inserted through the coresponding bolt holes in the flanges 2 TheFCIOTE Tool is slid over ple the pull rod untill the face of Ni
7. 2 02 20 OUTLET BALL SPRING 02 02 21 COPPER WASHER 02 02 22 VALVE COVER SCREW 02 02 23 STEEL BALL 02 02 715800 01 SERVICE KIT H 24 STEEL BALL 01 0 25 SPRING END CAP 01 0 26 L P SPRING 01 0 27 O RING 02 02 28 OVERLOAD COVER 01 0 SCREW 29 CAP 02 02 30 CONE SEAT 01 0 31 CONE 01 0 32 LONG SEPARATOR 01 0 SPRING 33 OVERLOAD COVER 01 0 SCREW 715900 01 SERVICE KIT I 34 BASE PLATE 01 0 35 SCREW 02 02 716100 01 SERVICE KIT 36 SCREW 04 03 37 CHECK BALL 04 03 38 SCREW 01 0 54 SCREW 01 0 716200 01 SERVICE KIT L 39 GAUGE COUPLER 01 0 MALE 40 GAUGE 01 0 FC1OTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL PAGE 24 HP350D HYDRAULIC TWIN PORT SEALED HAND PUMP EQUALIZER HOE ESK d KIT PUMP ITEM PART No DESCRIPTION QUANTITY QUANTITY 01 720101 01 PUMP HOUSI NG 01 02 710601 01 RESERVOIR 01 715300 01 SERVICE KIT C 03 O RING 01 0 04 BACK UP RING 01 0 05 H P PISTON 01 0 06 SNAP RING 01 0 07 O RING 01 0 08 BACK UP RING 01 0 09 L P PISTON 01 0 715500 01 SERVICE KIT E 10 YOKE BASE 01 0 11 SPRING PIN 01 0 715600 01 SERVICE KIT F 12 RELEASE VALVE 01 0 SCREW 13 WASHER 01 0 14 SEAL 01 0 15 RELEASE KNOB 01 0 16 SCREW 01 0 17 COUPLERS 01 0 18 CHECK BALL 01 0 715700 01 SERVICE KIT G 19 SPRING 02 02 20 STEEL BALL 02 02 21 OUTLET BALL 02 02 SPRING 22 COPPER WASHER
8. 6 01 752601 01 752701 01 752801 01 752901 01 753001 01 753501 01 754001 01 752510 01 No PART NO DESCRIPTION 01 750301 01 750401 01 750501 01 750601 01 750701 01 750801 01 751001 01 751101 01 751201 01 751301 01 751401 01 751501 01 751601 01 751701 01 751801 01 751802 01 751901 01 752001 01 READ INSTR STICKER HYDRAULIC COUPLER FRONT PLATE REAR PLATE SCKT HEAD SCREW SCKT HEAD SCREW CYLINDER NOSE SCREW CYLINDER NOSE ADAPTOR 5T H CYLINDER SET SCREW COUPLING HOSE BALL WASHER PULL ROD ROD WASHER NUT RETAINING SLEEVE RATCHET NUT PULL NUT CYLINDER REAPAI R KIT Illustrated on next page CAGE REAR RING CAGE FRONT RING CAGE SIDE BAR COLLET SEGMENT 1 COLLET SEGMENT 2 COLLET SEGMENT 3 NUT BODY NUT CAP LOCK WASHER REACTION PLATE END CAP COLLET RETAINING SPRING CAP RETAINING SPRING CAP RETAINING SCREW BUTTON HEAD SCREW BUTTON HEAD SCREW CIRCLIP INTERNAL CIRCILI P EXTERNAL 01 each 01 each 03 each 01 each 01 each 01 each 01 each 01 each 01 each 01 each 01 each 02 each 03 each 03 each 03 each 03 each 02 each 01 each FC1OTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL PAGE 22 5TE HYDRAULI CYLINDER PART LIST DESCRIPTION 300901 01 HYDRAULIC COUPLER 510707 01 SCREW 752502 01 CYLINDER BASE 752503 01 PISTON ROD 752504 01 SPRING 752505 01 SPRING LOCK 752506 01 SET SCREW 771106 01 FASTE NUT 771107 01 SC
9. AULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL PAGE 15 16 Once the flange bolts have been tightened sufficiently to remove any load from the turn the release valves on the pump s anticlockwise to release the E pressure from the hydraulic system z im 17 Now that the pressure has been released from the system the hydraulic Pump and Hoses can be detached FCLOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL PAGE 16 18 Now that the load has been released from the tools the secondary ratchet nut can be removed Rotate the nut anticlock wise through 30 degrees to disengage it from the rear plate then slide the nut off by gripping and pulling on the pull sleeve section of the nut SECONDARY RATCHET NUT 19 FC10TE can now be removed by gripping and pulling on the pull sleeve section of the primary nut PULL SLEEVE PRIMARY RATCHET NUT 20 The Pull Rod complete with pull nut and washer can now be withdrawn from the flange joint FCIOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL PAGE 17 21 Now that the tool has been removed all the flange bolts can be inserted and tightened in accordance with the relevant procedure FC1LOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL PAGE 18 7 EXAMINATION MAINTENANCE AND STORAGE On return from each job and before allocation against subseque
10. FCLOTE HYDRAULIC FLANGE CLOSING TOOL Operator Instruction Manual info equalizerinternational com www equalizerinternational com INNOVATION IN ITS MOST FUNCTIONAL FORM SECTION CONTENTS PAGE NO 1 INTRODUCTION 1 2 SAFETY INFORMATION 2 3 3 KIT COMPONENTS 4 4 TECHNICAL DATA 5 5 HOW THE FCIOTE HYDRAULIC FLANGE PULLERS WORK 6 7 6 INSTALLATION AND OPERATION 8 18 7 EXAMINATION MAINTENANCE AND STORAGE 19 21 8 PARTS LISTS 22 25 9 WEIGHTS AND DIMENSIONS 26 The Equalizer FCIOTE Hydraulic Flange Pulling Tools are tools designed to assist in the maintenance and installation of pipeline flange assemblies The FC10TE Hydraulic Flange Pulling Tools are used to close any flange joint made up of flanges with a bolt hole of 22mm 7 8 or greater producing a pulling force of up to 20T when used as recomended in pairs The FC1OTE can close from a distance of 600mm IM FCIOTE REVO7 07 07 14 HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL PAGE 1 2 SAFETY INFORMATION The operator MUST read this manual prior to using the tools Failure to comply with the following cautions and warnings could cause equipment damage and personal injury read the manual fully Read all the following instructions warnings and cautions carefully Follow all safety precautions to avoid personal injury or property damage during system operation Equalizer International Ltd cannot be responsible for damag
11. REW M5X16 752510 01 5T CYLINDER SERVICE KIT GASKET SEAL O RING BACK UP RING WIPER 01 each 01 each 01 each 01 each 01 each 01 each 01 each 01 each 01 each 01 kit 01 each 01 each 01 each 01 each FC1LOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL f PAGE 23 EQUALIZER PIN Te ike IN AN E EAS INT VN I HP550S HYDRAULIC SINGE PORT SEALED HAND PUMP KIT PUMP KIT PUMP ITEM PART No DESCRIPTION QUANTITY QUANTITY ITEM PART No QUANTITY QUANTITY 01 710101 01 PUMP HOUSING 0 716300 01 SERVICE M 02 730601 01 RESERVOIR 0 GAUGE COUPLER 715300 01 SERVICE KIT C FEMALE 03 O RING 01 0 COUPLER 04 BACK UP RING 01 0 PORT GAUGE 05 PISTON 01 0 ADAPTOR 06 SNAP RING 01 0 735100 01 SERVICE KIT 07 O RING 01 0 RESERVOIR BLADDER 08 BACK UP RING 01 0 OIL FILTER 09 LP PISTON 01 0 O RING 715500 01 SERVICE KIT E REFILLING PLUG 0 YOKE BASE 01 0 735300 01 SERVICE KIT O 1 SPRING PIN 01 0 HANDLE 715600 01 SERVICE KIT F YOKE 2 SEAL 01 0 PISTON PIN 3 WASHER 01 0 YOKE PIN 4 RELEASE VALVE 01 0 RETAINING RING SCREW HANDLE GRIP 5 SCREW 01 0 SCREW 6 RELEASE KNOB 01 0 735200 01 SERVICE KIT P 7 COUPLERS 01 0 SCREW 37 CHECK BALL 01 0 TAIL BASE 715700 01 SERVICE KIT G SPRING WASHER 8 SPRING 02 02 NUT 9 STEEL BALL 0
12. SIONS FCLOTESTD WEIGHTS AND DIMENSIONS TOOL WEIGHT 11kg 24 25 lbs GROSS KIT WEIGHT 23 5kg 51 80 Ibs Carry Case dimension 890 x 570 x 165 mm 35 04 x 22 44 x 6 50 39 37 1000 mm FCLOTEMAX WEIGHTS AND DIMENSIONS TOOL WEIGHT 11kg 24 25 Ibs GROSS KIT WEIGHT 36 5kg 50 47 lbs Carry Case dimension 890 x 570 x 165 mm 35 04 x 22 44 x 6 50 39 37 1000 mm 259 mm 10 21 HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL PAGE 26
13. e or injury resulting from unsafe product use lack of maintenance or incorrect product and or system operation Contact Equalizer International Ltd when in doubt as to the safety precautions and applications To protect your warranty use only good quality hydraulic oil of the grade 15cSt Only people competent in the use of hydraulic equipment should use these tools In all installations the site safety requirements must be adhered to ALSO the safety of the operator and when present any assisting personnel is of paramount importance along with the safety of others including when present the general public These instructions are only to cover the safe operation of THE EQUALIZER HYDRAU LIC TOOLS during normal maintenance installation operations All other safety aspects must be controlled by the operation supervisor FC1LOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL A CAUTION is used to indicate correct operating or maintenance procedures and practices to prevent damage to or destruction of equipment or other property A WARNING indicates a potential danger that requires correct procedures or practices to avoid personal injury A DANGER is only used when your action or lack of action may cause serious injury or even death o i IMPORTANT Operator must be competent in the use of hydraulic equipment The operator must have read and understood all instructions safety issues cautions
14. l be required to close the joint FCLOTE HYDRAULIC FLANGE CLOSING TOOL PAGE 13 OPERATOR INSTRUCTION MANUAL 11 Continue priming the Hand Pump untill the actuators have reached full stroke 100mm 4 12 Release the hydraulic pressure from the system This will allow the Actuators to retract and the secondary ratchet nut to advance along the pull rod automatically 13 Once the Actuators have fully retracted close the release valve and continue priming the hand pump untill the actuators have reached full stroke FCIOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL PAGE 14 closing the gap between flange faces Adjust 14 Repeat steps 12 and 13 to continue m N the pressure on each tool as neccesary to maintain an even gap around the joint Note If you are experiencing miss allignment of the flanges during the final stages of closing the joint Equalizer International s Flange Allignment tools can be used in conjuction with the FC10TE For information on these tools please vist www equalizerinternational com 15 Once the flange joint has been fully nn closed insert and tighten as many bolts as Ea possible with the 0 still in position 22 CAUTION The FCIOTE Ratchet Nuts will not release untill they fullly unloaded this is achieved by tightening the flange bolts untill all the load has been tranfered onto them FC1OTE HYDR
15. nt work the completeness of the Equalizer FC10TE hydraulic tool kits must be established and items examined to ensure that they are serviceable The FC10TE tools should be stored in a cool dry place At regular intervals and specifically after exposure to salt water Equalizer FC1OTE tools should be dismantled and all parts cleaned with a clean rag and WD40 or similar to remove dirt and old grease and then relubricated The following procedure should be followed when distmantling and rebuilding the tools 1 Unscrew and remove the primary ratchet nut retaining screws This will allow the ball washer and ratchet nut to be removed from the assenbly 2 Unscrew and remove the three lock screws and remove the end cap from the ratchet nut 3 Before disasembling the nut any further take note of the three centre dab marks on the cage rear ring the lock washer and the nut cap These marks should be alligned FC1OTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL RETAINING SCREWS BALL WASHER RATCHET NUT LOCK SCREWS CENTRE DAB MARKS PAGE 19 4 Unscrew the lock screws and remove the cage circlip The lock washer can now be removed to expose the Nut Cap Return Screws 5 Unscrew and remove the Nut Cap Return Screws and return springs this will allow the Nut Cap to be removed from the Rathet Nut Body 6 Having removed the Nut Cap you can then remove the upper Reaction Circlip
16. onal injury keep hands and feet away from the tool and workpiece during operation WARNI NG Always wear suitable clothing and Personal Protective Equipment PPE DANGER Do not handle pressurised hos es Escaping oil under pressure can pen etrate the skin causing serious injury If oil is injected under the skin seek medical attention immediately WARNI NG Never pressurize unconnected couplers Only use hydraulic equipment in a connected system IMPORTANT Do not lift hydraulic equip ment by the hoses or couplers Use the car rying handle or other means of safe trans port WARNI NG Never place fingers in a joint held by an activated tool CAUTI ON Never hammer of force the tool into a bolt hole if it does not fit easily you are using the wrong size of tool CAUTI ON Do not operate the equipment without lubricating all moving parts as in section 7 Use only high pressure molybde num disulphide grease FC10TE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL d AL 3 KIT COMPONENTS FC10TE STANDARD KIT COMPONENTS 1 x Tool 2 x 10 000 psi 700 bar 5T Hydraulic cylinders 1 x 10 000 psi 700 bar HP550S Sealed Hand Pump with Gauge 1 x 10 000 psi 700 bar Hydraulic Hose 2m 78 75 1 x Instruction Manual 1 x Carry Case with Protective Foam Inserts Product Code FCIOTESTD FC1OTE MAXI KIT COMPONENTS 2 x FCLOTE Tools 4 x 10 000 psi 700 bar 5T Hydraulic cylinders 1
17. the tool comes into contact with the flange 3 The ratchet nut is slid over the pull rod and locked into the tool REACTION NUT 4 hydraulic hand pump and Hoses are connected v FC1LOTE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL The Hand Pump is actuated untill the cylinders reach full stroke The Hydraulic pressure is released and the cylinders are allowed to fully retract Release Valve The Hand Pump is actuated untill the cylinders reach full stroke Steps 6 and 7 are repeated untill the flange joint is closed FC10TE HYDRAULIC FLANGE CLOSING TOOL OPERATOR INSTRUCTION MANUAL 6 INSTALATION AND OPERATION Note Prior to attaching the FCT10TE it is important that the location of the tools around the flange joint is considered the tools should be attached to the bolt holes at the points where the highest load is expected Consideration should also be given to the flange Gasket Seal ring it may be neccesary to insert the Gasket Seal ring Prior to attaching the tools 1 The flanges are placed with a EEE gap of no more than 600mm between or the backs of the flanges and within p reasonable allignment 2 Having determined the best location for the tools insert both pull rods through the bolt holes in one flange and into the corresponding bolt holes of the mating flange SHORT THREADED SECTION LONG THREADED SECTION
Download Pdf Manuals
Related Search