EMIV-DUAL User Manual Application Information
Contents
1. AnyTime AnyPlace Any Wireless Data Solutions AnyDATA EMIV DUAL User Manual Application Information 01 EMIVDUAL 1 XI June 29 2004 AnyDATA NET Inc Hanvit Bank B D 6F Byulyang dong Kwachon KOREA Tel 82 2 504 3360 Fax 82 2 504 3362 EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information AnyDATA NET Inc Hanvit Bank B D 6F Byulyang dong Kwachon KOREA Copyright 2001 AnyDATA NET Inc All rights reserved Printed in the Republic Of KOREA All data and information contained in or disclosed by this document are confidential and proprietary information of AnyDATA NET Inc and all rights therein are expressly reserved By accepting this material the recipient agrees that this material and the information contained therein are held in confidence and in trust and will not be used copied reproduced in whole or in part nor its contents revealed in any manner to others without the express written permission of AnyDATA NET Inc AnyDATA NET Proprietary Restricted Distribution This document contains critical information about AnyDATA NET products and may not be distributed to anyone without permission of AnyDATA NET Inc All data and information contained in this document are proprietary and confidential information of AnyDATA NET Inc No part of this document may be reproduced in any form or any means without written permission2. A Code 1 023MHz Chip Rate 152dBm EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 2 2 5 Standards IS 95A B C Protocol Between MS amp BTS IS 96A Voice Signal Coding IS 98A Base MS Function IS 126 Voice Loop Back IS 637 Short Message Service IS 707 Data Service Built in TCP IP AnyDATA proprietary software IS 657 packet data EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 2 3 Interface Diagram ANTENNA RS 232C RF UNIT DEBUG MSM6050 External Power DTG2000 DUAL APPLICATION EMIV DUAL Figure 2 1 Interface Block Diagram EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 2 4 EMIV DUAL General Features Figure 2 2 EMIV DUAL General Features 2 5 Internal Modem Features SSC NIE 5 d i Lt d i af ane a m Sai E RW LI 7 cg m eu 3 m e i E TE E 4 LR q T T 1 be L5 f m T Figure 2 3 I
3. IS 707 A IS 2000 e 45MHz for Cellular and 80MHz for PCS Frequency Interval Band Width 1 23MHz Operating Voltage DC 7V 16V E Sleep mode 30mA Idle mode 70mA P Traffic mode 350mA Max at 12V Operating Temperature 30C 60C Frequency Stability 300Hz for 800MHz CDMA and 150Hz for 1900MHz CDMA dut Magnet mount helical antenna 50ohm SS 1dBi Gain for 800MHz and 1900MHz 4dBi for 1575MHz External Interface l RS 232 Analog audio Power Antenna Debug port EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 2 2 2 Receive Specifications PARAMETERS DESCRIPTIONS 869 04 893 97 MHz for 800MHz CDMA and EE 1931 25 1988 75MHz for 1900MHz CDMA Interference Single tone 30dBm 900KHz Below 101dBm for 800MHz Rejection single tone 30dBm 1250KHz Below 101dBm for 1900MHz Suppression Input Dynamic Range 25dBm 104dBm 2 2 3 Transmit Specifications PARAMETERS DESCRIPTIONS e S 824 04 848 97 MHz for 800MHz CDMA and dx a 1851 25 1908 75MHz for 1900MHz CDMA Nominal Max Power 0 32 W 24 7dBm Peak Power in Operation Mode Mini ll inimum Controlled Below 50d Bot Output Power 900KHz Below 42dBc 30KHz 1 98MHz Below 54dBc 30KHz 1250KHz Below 42dBc 30KHz 1 98MHz Below 50dBc 30KHz 0 35W 25 5dBm Max Power Spurious 2 2 4 gpsOne Receiver Specifications L1 1575 42MHz C
4. programmable data sizes programmable stop bits and odd even no parity The UART operates at a 115 2kbps maximum bit rate DP RI Output to host indicating coming call DP RTS Ready for receive from host DP RXD Input data to the modem DP CTS Clear to Send Modem output signal GND Signal Ground Signal ground Figure 4 1 UART Interface Pinouts DP TXD Output data from the modem DP DTR Data Terminal Ready Host ready signal EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 5 Electrical Specifications 5 1 Absolute Maximum Ratings Operating the modem under conditions that exceed those listed in the Absolute Maximum The Ratings table may result in damage to the modem Absolute Maximum Ratings may be considered as limiting values and are considered individually While all other parameters are within their specified operating ranges the functional operation of the modem under any of the conditions in the Absolute Maximum Ratings table 1s not implied Table 5 1 Absolute Maximum Ratings Storage Temperature Voltage On Any Input o 7 90 5 v O VotageOnAnyOupu Supply Voltage 1 Initializing Current o pf pma 5 2 Recommended Operating Conditions Supply Voltage Operating Temperature Operating Humidity 95 50 C Relative Humidity 5 3 Power Consumption 350mA MAX 5 4
5. Serial Interface Electrical Specifications EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 6 Mechanical Dimensions 6 1 EMIV DUAL Outline DEBUG RS2320 BATT DC12V 60mm I Z B 8mm e IO 00000 EKLE H GUST GE Frk 12mm d AnyDATA EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 7 FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 Part22 and Part24 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment i
6. ations 6 Mechanical Dimension 6 1 EMIV DUAL Outline 7 FCC Notice 8 Installation Example EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 1 Introduction 1 1 Purpose This Manual provides hardware interface and programming information for EMIV DUAL CDMA Wireless Data Modem 1 2 Organization The interface and operation section is organized into the following subsections B Section 2 Introduces users to the EMIV DUAL CDMA Wireless Data Modem basic features and general specifications B Section 3 Contains EMIV DUAL Pin description DC12V Input Port 8pin Serial Port and Debugging Port Section 4 Describes the UART Interface Section 5 Specifies the recommended operating conditions DC voltage characteristics I O timing and power estimations for the modem Section 6 Provides package dimensions and outlook features for the modem Section 7 Describes the FCC Notice 1 3 Revision History The revision history for this document is shown in Table 1 1 Table 1 1 Revision History June 2004 Initial Release EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 2 Overview 2 1 Application Descriptions The CDMA Wireless Data Modem is a complex consumer communications instrument that relies heavily on both digital sig
7. evice this device and its antenna should generally maintain a separation distance of 20cm or more from a person s body BP Antenna Gain must not exceed 1dBi Special accessories In order to ensure this device in compliance with FCC regulation the special accessories are provided with this device and must be used with the device only The user is not allowed to use any other accessories than the special accessories given with this device EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information Contents 1 Introduction 1 1 Purpose 1 2 Organization 1 3 Revision History 2 Overview 2 1 Application Description 2 2 Technical Specifications 2 2 1 General Specification 2 2 2 Receive Specification 2 2 3 Transmit Specification 2 2 4 gpsOne Receiver Specification 2 2 5 Standards 2 3 Interface Diagram 2 4 EMIV DUAL General Features 2 5 Internal Modem Features 3 PIN Description 3 1 8 Pin Connector RS232 Standard 3 2 3 Pin Connector Debugging 3 3 DC Power Connector EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 4 Interface Descriptions 4 1 Overview 4 2 RS232 Interface Standard 5 Electrical Specifications 5 Absolute Maximum Ratings 5 20 Recommended Operating Conditions 5 3 Power Consumption 5 4 Serial Interface Electrical Specific
8. nal and embedded processor technologies The Wireless Data Modem manufactured by AnyDATA NET supports Code Division Multiple Access CDMA This operates in 800MHz CDMA and 1900MHz PCS spectrum In a continuing effort to simplify the design and to reduce the production cost of the Wireless Data Modem AnyDATA NET has successfully developed the EMIV DUAL The EMIV DUAL is AnyDATA NET s latest compact Wireless Data Modem operating in 800MHz CDMA and 1900MHz PCS spectrum also contains complete digital modulation and demodulation system for CDMA standards as specified in IS 95 A B and IS 2000 The subsystem within the EMIV DUAL includes a CDMA processor MSM6050 an integrated CODEC with an ear piece and microphone amplifiers and an RS 232 serial interface supporting forward link data communications of a rate of 153kbps The EMIV DUAL provides external interface External interface includes the standard RS 232 Digital Audio External reset control parallel LCD Display Keypad Ringer extension ports and R UIM for China market The EMIII DUAL has the capability to power down unused circuits in order to dynamically minimize power consumption EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 2 2 Technical Specifications 2 2 1 General Specifications PARAMETERS DESCRIPTIONS Code Division Multiple Access CDMA CDMA Protocol IS 95 A B IS 126 IS 637A
9. nternal Modem General Features DTG2005 25 AL EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 3 PIN Description 3 1 8 Pin Male Modular Jacks RS232 Standard Molex 85503 Figure 3 1 Right Angle Modular Jacks 85503 Molex Figure 3 1 Right Angle Modular Jacks Pin Description 85503 Molex 8P 3 2 3 Pin Connector Debugging EE GND TXD RXD Figure 3 2 Debugging Connector 5268 Molex 3P 3 3 DC Power Connector EES DC 12V Figure 3 3 DC 12V Power Connector 5268 Molex 2P RS 232 PC EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 4 Interface Descriptions 4 1 Overview This chapter covers information required to design the EMIV DUAL into a subscriber unit application In addition the internal signals that are necessary for complete understanding of the UART interfaces are described below 4 2 RS232 Interface Standard The Universal Asynchronous Receiver Transmitter UART communicates with serial data that conforms the RS 232 Interface protocol The modem provides 5 0V CMOS level All the control signals of the RS 232 signals are active low but data signals of RXD and TXD Are active high The UART has a 64byte transmit TX FIFO and a 64byte receive RX FIFO The UART Features hardware handshaking
10. nto an outlet on a circuit different from that to which the receiver is connected B Consult the dealer or an experienced radio TV technician for help EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information 8 Installation Example Molex 8 Pin to DBS Cable DEBUG ROO BATT DC POWER SUPPLY HEADSET EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions
11. of AnyDATA NET Inc Although the information in this document has been carefully reviewed and its believed to be reliable AnyDATA NET Inc does not assume any liability arising out of the application or use of any product described herein Neither does it convey any license under its patent rights nor rights of others Send Technical Questions to johnkim anydata net EMIV DUAL Reference Manual Application Information 01 EMIVDUAL 1 XI June 29 2004 EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information Introduction The EMIV DUAL is designed for the test and simulation of the CDMA wireless data communications User can connect the EMIV DUAL to your PC or Notebook and easily test the wireless communications User can use this to develop your applications software even before user s own hardware is ready It also can be used as a debugging during user s hardware test Disclaimer and Limitation of Liability AnyDATA NET Inc assumes no responsibility for any damage or loss resulting from the misuse of its products AnyDATA NET Inc assumes no responsibility for any loss or claims by third parties which may arise through the use of its products AnyDATA NET Inc assumes no responsibility for any damage or loss caused by the deletion or loss of data as a result of malfunctions or repairs The information disclosed herein is the exclusive propert
12. y of AnyDATA NET Inc and no part of this publication may be reproduced or transmitted in any form or by any means including electronic storage reproduction execution or transmission without the prior written consent of AnyDATA NET Inc The information contained in this document is subject to change without notice Reproduction adaptation or translation of this document is prohibited without prior written permission of AnyDATA NET Inc EMIV DUAL V1 0 AnyDATA NET Proprietary Use Subject to Restrictions Interface Description EMIV DUAL Reference Manual Application Information FCC RF Exposure Information Warning Read this information before using this device In August 1996 the Federal Communications Commission FCC of the United States with its action in Report and Order FCC 96 326 adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters Those guidelines are consistent with the safety standard previously set by both U S and international standards bodies The design of this device complies with the FCC guidelines and these international standards IN CAUTION e Operating Requirements Bb The user can not make any changes or modifications not expressly approved by the party responsible for compliance otherwise it could void the user s authority to operate the equipment To satisfy FCC RF exposure compliance requirements for a mobile transmitting d
Download Pdf Manuals
Related Search