User manual for MICA ML
Contents
1. The cushion on the back side of the battery must be placed in between the battery and the back cover be sure not to damage the battery wires when doing this 5 Attach the battery wire to the printed circuit board check that the polarity is correct Close the lamp s back cover Spare parts for ML 600 series lamps 1 H0071 1 ML 601 cover unit orange H0071 2 ML 600 cover unit yellow H0071 3 ML 602 cover unit yellow 2 H0072 1 ML 601 switch replacement unit H0072 2 ML 602 switch replacement unit 3 H0073 1 ML 601 printed wiring board 12 red LED H0073 2 ML 602 printed wiring board 6 red 6 greed LED rS 4 H0074 1 Lens and gasket ax d 5 H0075 1 Reflector and installation A Wey plate with screws La MA 6 H0076 1 ML 600 electronics unit Qe H0076 2 ML 601FIN electronics unit IQ H0076 3 ML 601DB electronics unit Da H0076 4 ML 602 electronics unit 7 H0077 1 Bulb light pattern adjustment bushing 8 H0032 1 Bulb Px 13 5 2 4 W H0032 2 Bulb Px 13 5 4 W ACN 9 H0079 1 600 battery 1800 mAh ISS H0079 2 601 602 battery 1350 mAh Y 10 H0080 1 Back cover orange BS H0080 2 Back cover yellow U 11 H0081 1 Back cover locking band 12 H0082 1 Belt clip basic model H0082 2 Belt clip railway model Spare parts for MICA MLC charging stand H0085_2 Plastic cover and top bolt H0086_1 Back plate and receptacle H0087_1 Bottom bolt H0088_2 Printed circuit board2. voltage for charging stand 12VDC max 30VDC i Weight of charging stand ca 170g BATTERY DISPOSAL A used battery is classified as hazardous waste Please make sure that the battery is properly disposed of in accordance with instructions from the authorities Do not dispose of the battery by burning it TO USER WARRANTY CONDITIONS Manufactured in Finland MICA ML is a small yet effective rechargeable product family for Warranty period for the lamp and the battery is one year The warranty period begins when demanding professional use The frames are splash and shock proof The lamps bright light the lamp is purchased The warranty covers manufacturing and raw material defects in line pattern is achieved by using a high halogen and an aluminum reflector At best the lamps with general warranty conditions Under the warranty period the lamp may be serviced by operating time is three hours with a 4W bulb and a fully loaded NiMH battery an authorized MICA service agent only If you need the lamp to be serviced under the warranty Solas please contact the retailer from whom you purchased your MICA lamp Please read this manual carefully in order to secure your lamp a long service life OTHER MICA LAMPS For more information please contact Mica Elektro Oy directly or visit our web site at www mica fi Mica Elektro Oy LTD 5 2005 We reserve the right to revise any information in this user eae ao Oy ECO noe PNE Bela a Ete One manual w
3. 01877_2 OPERATING TIMES Table A1 The operating times here refer to a fully loaded battery and full brightness With a 2 4 W bulb 4h20min Prior to use remember The signalling LEDs will remain in operation for more than 12 hours with to attach the battery wire a fully charged battery to the printed circuit board ACCESSORIES FOR MLC lt The battery must always 1 Wire for connecting to a cigarette lighter 01112 s 2 IL 1 AC DC adapter 230 VAC 12VDC 11270 f be charged full prior to 3 IL 4 AC DC adapter 230 VAC 12VDC for five charging stands 11322 using the lamp 4 IL 5 automatic exchanger for five charging stands 11311 imi TECHNICAL DATA FOR ML LAMPS Bulbs 6 0V 2 4 W or 4W PX13 5 Battery ML 600 NiMH 6 V 1800mAh Battery ML 601 602 NiMH 6V 1350mAh Electronics 8 bit microcontroller Lens 41 5x 3 mm toughened glass Reflector Aluminum Operation temperature 20 45 C lamp Operating time gt 4h 2 4W full power Enclosure class IP 54 splash proof Dimensions h x w xd 120 x 64 x 55mm with belt clip Weight ca 315g ML 600 amp ca 275g ML 601 602 TECHNICAL DATA FOR MLC CHARGING STAND Quick charge voltage 750mA Maintenance charge voltage 100mA Charging temperature range 10 C 40 C Quick charging time 2h 45min Maximum charging time 4h in fault situation for security reasons mica Conditions for ending charging dV Tmax lt 45 C tout lt 4h Feed
4. arged the green light L3 marked ready will be lit and the light L2 will be turned off At that time the lamp is ready to be used and the charging stand will switch to the maintenance charging mode 4 The lamp must always be stored in the charging stand in order for it to be ready for use at all times The MICA MLC quick charging stand will not overcharge the battery of the lamp REPLACING BULB Free the lamp s locking bolt and lift the back cover off Turn the bulb contact slide to the side please see the figure attached Turn the black bulb locking cap open and remove the faulty bulb Install the new bulb be sure not to touch the bulb glass with your bare hands Turn the locking cap back on secure it tightly Turn the bulb contact slide back over the bulb contact Adjust the light pattern by turning the metal bushing Carefully secure the frame halves back against each other don t forget the gasket and lock the back cover with the locking bolt ONDMNABRWNHE REPLACING BATTERY PACKAGE It is time to replace the battery when the operating time remains clearly shorter than that given in Table A1 1 Open the lamp and carefully detach the battery connector from the printed circuit board 2 Carefully lift off the battery mind the wires note the two sided tape on the bottom 3 Place the new battery in its place in between the plates and press it so that it touches the bottom of the frame Note
5. ithout a preliminary notice e tel 358 9 5617 666 fax 358 9 5617 6688 mic email info mica fi internet www mica fi Cele Kk tro Prior to use Open the lamp and attach the TAKING INTO USE 1 INSTALL CHARGING STAND MLC The stand may not be placed on a platform manufactured of a highly flammable material and its voltage feed must be continuous you may not break it with a timer for example Choose a suitable installation place and mount the MLC charging stand with two screws Connect the power feed wire use either a vehicle battery or a MICA IL 1 AC DC adapter in the charging stand s round quick coupling Alternatively you can connect the feed wire in the screw terminals on the back of the stand be sure to connect the plus and the minus poles correctly and finally tighten the cable clamp please see the figure The red light L1 will show that you have correctly connected the feed voltage and that the MLC charging stand is ready to be used battery wire to the printed circuit board 2 CHARGE THE LAMP FOR AT LEAST 4 HOURS BEFORE USING IT THE FIRST TIME The battery of a new lamp is always empty Please note that the lamp will not offer its full operating time until after it has been charged and discharged ca 5 10 times During the first five times you use it it is important that you completely drain out the battery USE OF LAMP SWITCHES AND SIGNAL LIGHTS The lamp has the following switches and signal ligh
6. sruption in power feed The safety light function can be activated by placing the lamp on the charging stand and by pressing the main switch A once Green LED4 indicates the safety light mode and the LED also shows that the bulb is okay Operation times are given in Table A1 Stepless brightness adjustment halogen bulb The lamp will warn you when the battery charge is low the red warning light L5 at the top of the lamp will be lit ca 15 20 minutes before the battery is empty and the lamp will be shut down Control electronics will automatically turn off the lamp prior to deep discharge of the battery After use the lamp must be stored on the MLC charging stand There is a spare halogen bulb inside the lamp s frame please see replacing bulb CHARGING IN MICA MLC CHARGING STAND The MLC charging holding stand is to be used with ML lamps only The battery will be charged from empty to full in approximately two hours The smart charging technology guarantees optimal and safe charging in any situation Feed voltage must be taken from a MICA IL 1 AC DC adapter or a 12 24V vehicle battery 1 The red light L1 will be lit when the charging stand is attached to proper feed voltage 2 The ML lamp must be placed on the MLC charging stand When charging begins orange light L2 marked charging will come on The lamp will be automatically turned off when it is placed in the MLC charging stand 3 When the battery is fully ch
7. ts Here is a short introduction to the switch and lighting functions of the MICA ML versions ML 600 is a model equipped with stepless power adjustment The lamp will be lit with full power when the main switch A is pushed for a short period of time When you keep the switch pushed down the light output will be automatically adjusted from dim to bright When you release the switch the lamp will burn with the adjusted brightness ML 601 is a signaling lamp equipped with a red LED and a halogen bulb Switch A is an on off switch for the bulb and switch B for the LED You can adjust brightness of the halogen bulb steplessly by holding switch A down a bit longer Then the light output will be adjusted from dim to bright ML 602 is a signaling lamp equipped with a red and a green LED and a halogen bulb The halogen bulb will be lit to full power when switch A is pushed down for a short period of time Switches A B and C are the on off switches for their groups When pushing a switch to position on the light for the previous group will be turned off You can adjust brightness of the halogen bulb steplessly by holding switch A down a bit longer Then the light output will be adjusted from dim to bright COMMON FUNCTIONS FOR THE MICA ML SERIES LAMPS The safety light function is a standard in all of the MICA ML models When in the safety mode the lamp will be turned on if there is a di
Download Pdf Manuals
Related Search