TECHNICAL DETAILS DEVICE INSTALLATION User Manual
Contents
1. Black Ground GND Please Note Our product has the memory back up so the Permanent feed is not required for all installations DISCLAIMER AND WARRANTY Disclaimer lf your cars electrical system begins to behave erratically please disconnect the DAB R device physically immediately and have it checked by your installer Dension and its authorized distributors and retailers are not liable for any incidental consequential or indirect damages or loss and do not assume liability for any diagnostic fees The use of handheld devices while driving may be subject to government legislation Please ensure that your use of the Dension device complies with applicable traffic laws Dension does not assume liability for any events resulting from the illegal or irresponsible use of handheld devices while driving Dension reserves the right to modify its products or specifications without prior notice Warranty Dension devices carry a one year limited warranty that protects you from defects in material and workmanship of products sold by Dension or its authorized distributors and retailers Dension does not warrant any installation work or assume liability for any damage caused due to negligence improper installation or operation For warranty claims proof of purchase is required2. E CONTENTS Main device DAB R module Car side power cable Power wire for active antenna Power cable with cigar lighter adapter Installation accessories Quick Start Guide Remote Controller Front view not in use notinuse SMB antenna Back view Active DCIN Authorised Status AUX In ANT 12V update only LED DEVICE INSTALLATION Use the included car side power cable and connect the 3 power leads as follow e Red 12V Battery permanent 12V or ACC e Purple 12V Switched ACC or ignition e Black Ground GND lt gt Slaw 8 rm O O power connection DAB DAB Digital Audio Broadcast is an international standard for digital radio broadcasts The availability of DAB stations and broadcast coverage are very much location and country specific Please consult your local broadcast information for availability POSITIONING THE DAB ANTENNA The DAB reception and performance depends on many factors both in the vehicle and other external conditions Before you startthe antenna installation and or the producttesting please make sure that you have a good DAB coverage and reception Important notes e If your vehicle comes with metalized windscreen e g windscreen heating the external antenna is required to be mounted outside of the car e The DAB module supports both amplified and non amplified aerials For amplified antennas 12V power is provi
3. PENSION DAB R DAB Radio Receiver with Remote Controller User Manual DBR 9202 1 The Dension DAB R is a universal solution for listening to your favorite DAB Digital Audio Broadcast stations in your car This device offers full DAB information metadata on the display of your car radio through RDS if your car radio supports radio text BBC R2 Now playing White Light by George Michael es a a C This manual will explain how to easily install and use the DAB R device with our remote controller Please study this user guide carefully and keep it handy in case any questions may arise later TECHNICAL DETAILS e Digital Audio Services DAB DAB DMB A Supports DAB DAB standards RF Frequency Range DAB Band III Channels 5A to 13F 174 MHz 240 MHz RF Sensitivity for DAB Band Ill 98 dBm 100 dBm FM Transmission Range 87 6 MHz 107 9 MHz e Power supply 11 V 16V DC Fuse 1 amp Input Connectors DC micro fit power plug 3 5mm stereo audio Auxiliary Input socket AUX in connector for external devices Presets 10 DAB station Presets DAB aerial connector SMB Male Passive and active antenna support Separate power supply output is provided for active antennas Phantom powering is not supported Operating Temperature Range 10 70 deg C Storage Temperature Range 40 85 deg C WARNING Do not expose the remote controller to direct sunlight or heat PACKAG
4. ded by the DAB R receiver via the 2 pin molex connector Read the manual of the antenna used carefully and follow the instructions in order to find the right place for installation Always test read next chapter the DAB functions before finalizing the installation REMOTE CONTROLLER DENSION FM FREQUENCY SETUP Manual Scanning In order to set the FM frequency you need to follow the next steps e Turn the ignition ON e Press and hold the Q button for 3 seconds e Enter the frequency from 87 6 876 to 107 9 1079 e Press the rm button to store the valid frequency Switch to the selected frequency with your radio Automatic Scanning You can also start an automatic FM frequency scan To use this option you need to do the following e Turn the ignition ON e Press and hold the rm button for 3 seconds Press the O up arrow button After this the device will be looking for a free frequency and will set it automatically This frequency can be found if you do an FM scan with your radio OPERATION During the first use or if there is no station selected the DAB R title is shown on the RDS display of the radio First of all you need to perform a DAB scan which you can do by pressing the ean button During the scan you should see DAB SCAN on the display If the NOSIGNAL message appears on the radio that means there is no DAB reception In this case please check the location and the connection of
5. the areal Navigation between stations By pressing the up and amp down arrow buttons you can skip to the next or previous stations If you press and hold these buttons you can skip in 5 station steps alphabetically Presets You can store presets to the O O buttons To store the actually played station you need to press and hold one of the numerical buttons After this you can switch to that station directly by short pressing the same button Auxiliary source The device gives you the possibility to listen to music from an external source through a 3 5mm Jack connector In order to mute the DAB radio and use the Auxiliary input of the device you need to press the button In this mode you should see AUX in the RDS display Pressing the button again reactivates the DAB source Please note The device connected to the auxiliary input has to be paused separately using the controls of the device itself Diagnostic During playback with the 0 button you can switch between the text of the actually played DAB channel and between the software information of the DAB R device and of the DAB module POWER SUPPLY INFORMATION Use the included car side power cable and connect the 3 power leads as follow 3 wire installation Red 12V Battery permanent 12V or ACC e Purple 12V Switched ACC or ignition Black Ground GND 2 wire installation e Red amp Purple Terminated together 12V Switched
Download Pdf Manuals
Related Search