User Manual
Contents
1. Caution Please do not install a machine in the unstable place to which it is shaky or leans There is a danger of receiving an injury When you move have a base There is a danger of receiving an injury When you install a machine please install to a place with no dust and the place which is not influenced with a liquid It becomes the cause of failure if the installation method is mistaken Caution Don t put a hand under the hollow drill bit There is a danger of receiving an injury Turn off the power supply beforehand when attaching or detaching hollow drill bits There is a danger of receiving an injury Don t touch the blade point of the hollow drill bit There is a danger of receiving an injury 1 Setting a drill bit Insert a drill bit into the chuck and tighten with the provided wrench 2 Setting the punch depth After installing a drill bit adjust the stop nut that limits downward travel so that the drill bit just enters the brown fiber plug on the table when the drill bit is fully extended 3 Setting paper Open the paper guide and place the paper on the table Close the paper guide the paper will be centered on the table automatically Push down both sides of the paper clamp to secure the paper Clamping pressure should be set according to the type of the paper VS 15 Do not try to punch more than 30mm of paper VS 25 Do not try to punch more than 50mm of paper WHITAKER 800 243 i W atts 800 243 9222. 6 www WhitakerBrothers com 4 Setting the back margin Distance between the edge of the paper and the center of the holes The back margin can be set at any value from 6mm to 35mm by turning the back margin adjusting bolt use the scale on the table as a guide 5 Distance of the holes The program pitch bar can be set to select any of six pitches Continuous punching can be done precisely thanks to proper paper setting by the clutch stopper Caution Don t put a hand under the hollow drill bit There is a danger of receiving an injury Don t touch any rotating part There is a danger of receiving an injury Don t bring a hand face hair sleeves of clothes and the like close to the rotating parts of the machine There is a danger of receiving an injury When you change into unusual states like smoke comes out please turn off the power switch of a main part and pull out a power supply plug from a wall socket after that There are failure a fire and fear of an electric shock The hollow drill bits become heated when they are drilling Don t touch them when they are drilling Touching them may cause a burn Don t touch the blade point of the hollow drill bit There is a danger of receiving an injury Please do not make a hole in paper with foreign substances such as a needle of a stapling machine Moreover also things other than paper There is a danger of receiving an injury Please do not make a hole hard paper and
3. after that There are failure a fire and fear of an electric shock Caution Please do not install a machine in the unstable place to which it is shaky or leans There is a danger of receiving an injury When you move have a base There is a danger of receiving an injury When you install a machine please install to a place with no dust and the place which is not influenced with a liquid It becomes the cause of failure if the installation method is mistaken Turn off the power supply beforehand when attaching or detaching hollow drill bits There is a danger of receiving an injury Don t touch the blade point of the hollow drill bit There is a danger of receiving an injury The hollow drill bits become heated when they are drilling Don t touch them when they are drilling Touching them may cause a burn Please do not make a hole in paper with foreign substances such as a needle of a stapling machine Moreover also things other than paper There is a danger of receiving an injury Please do not make a hole hard paper and near the hole which have opened in piles There is a danger of receiving an injury Turn off the power supply beforehand when adjusting the fiber plug There is a danger of receiving an injury 10 When a machine stopped during use turn off the power switch and pull out a power supply plug from a wall socket after that There is a danger of begins to turn again And there is a danger of receivin
4. g an injury WAKER 800 243 9226 www WhitakerBrothers com Introduction Read this Operation Manual carefully before use In particular be sure to read Safety Instructions page 1 to ensure that the machine will be used properly Keep the manual at an appointed place with care so that it may be accessible whenever necessary The specifications of this product are subject to change for improvement Therefore don t mistake the Operation Manual of one product of the same model for that of another because descriptions in the Operation Manual of products of the same model may differ 1 Before use 1 Check the kinds and quantities of accessories Standard Accessories U S version 6 5mm X 1pc Hexagonal wrench 4mm X 1pc Fiber plug 2pcs W290xD41xH3 Chip receptacle Sharpener Oilstone Paraffin Eyeleteer Operation manual WHITAKER 800 243 i W atts 800 243 9226 www WhitakerBrothers com 2 Exterior features Clutch stopper handle Handle Chip receptacle Clutch stopper N Paper clamp Va A Switch ZIY S E CIN es P a L Upper lever H Lower lever s to LT fi unclamp 8 nE Down to Adjuster bolt Adjuster Program pitch bar Paper guide Back margin Centering scale adjusting bolt Hexagonal wrench Hollow drill bit WHITAKER 800 243 i W atts 800 243 9226 www WhitakerBrothers com 2 Operating instructions 1 Checks before setting
5. m a wall socket after that There is a ae of begins to turn again And there is a danger of When machine use long hours motor ece hot To avoid the damaging of the motor rotation of drill automatically stops by activating of thermal protector When machine become cold drill automatically rotates again if machine switch is not turned off This might be cause of the injure of operator So when thermal protector works turn off the power switch and pull out the power supply from the outlet 4 Product specifications T aa 5 6 6 5mm Diameter of drill bit 4 5 6mm 4mm Optional adapter is required 6 to 35mm normal PAEAN pio Semin 12 5 to 35 pi drill i Maximum paper length sau a ar Automatic centering Automatic centering Table size W480 x D260 mm W480 x D260 mm W480 x D340 x H430 mm W480 x D340 x H470 mm Net weight Net weight 13kg 14kg 120V 230V 240V 120V 230V 240V Power AC 50 60Hz 90W 50 60Hz 90W AC 50 60Hz 180W Power cord length 2m covered 2m Vinyl covered 5 Ordering consumables etc When ordering consumables or parts such as fiber plug specify the machine model Keep this Operation Manual at an appointed place with care so that it may be available whenever required lf this Operation Manual is stained or lost make contact with the distributor or our salesman or customer service section to ask for a new operation manual after making sure of its contents When transmitting this produc
6. near the hole which have opened in piles There is a danger of receiving an injury 6 Operating the punch Turn on the power then lower the drill bit quickly without stopping until the stop nut halts the descent this should take about one second 7 Finishing the punch After the punch finished turn off the power Take paper after the rotation of a drill bit completely stopped 3 Maintenance 1 Checking the edge of the drill bit If punching requires more force than normally or if the drill bit lifts paper with it it s time to sharpen the drill bit It s a good idea to sharpen the drill bit regularly before this happens 2 Sharpening the drill bit A dull drill bit may make punching hard A dull drill bit is more easily damaged than a sharp one To sharpen it follow these steps WHITAKER 800 243 i W sats 800 243 9226 www WhitakerBrothers com Caution Don t put a hand under the hollow drill bit There is a danger of receiving an injury Don t touch any rotating part There is a danger of receiving an injury Don t bring a hand face hair sleeves of clothes and the like close to the rotating parts of the machine There is a danger of receiving an injury Don t touch the blade point of the hollow drill bit There is a danger of receiving an injury 1 Place the provided sharpener on the fiber plug as shown at the right and turn on the power 2 Turn the handle until the rotating drill bit touches the sharpe
7. ner then turn a little more The drill bit is sufficiently sharp when you hear a high pitched squeal 3 Remove the burrs on the edge by holding the provided oilstone parallel to the rotating drill bit and bringing then in to contact until all burrs are gone 4 Use the paraffin to the drill bit for lubrication Hollow drill bit Bring the dull drill bit down onto the sharpener Paraffin Oilstone Hold the oa parallel to the drill bit as you remove burrs Sharpener 3 If bottom sheets are not completely punched The fiber plug wears out with continued use When the bottom sheets are not punched completely turn the fiber plug over or turn it 180 replace as necessary Caution Turn off the power supply beforehand when adjusting the fiber plug There is a danger of receiving an injury 4 Emptying the chip receptacle The tiny paper disks chips that are punched out of the paper travel up through the hollow drill bit and accumulate in the chip receptacle Empty the receptacle often before it becomes full To remove the receptacle simply lift it out of the machine After emptying make sure you seat it securely again WHITAKER 800 243 i W atts 800 243 9226 www WhitakerBrothers com 5 When thermal protector works Caution When a machine stopped during use turn off the power switch and pull out a power supply plug fro
8. t to another person be sure to attach this Operation Manual to the product UCHIDA YOKO CO LTD 9 15 Shiomi 2 chome Koto ku Tokyo Japan Tel 81 3 5634 6350 Fax 81 3 5634 6856 E mail overseas uchida co jp www WhitakerBrothers com
9. www WhitakerBrothers com VS 15 VS 25 OPERATION MANUAL Use the machine properly after reading the Safety Instructions given below carefully These safety instructions are given to ensure that the machine will be used safely and properly and to prevent operators from sustaining harm and injuries UCHIDA YOKO CO LTD TOKYO JAPAN V 02 WHITAKER 800 243 9226 SINCE 1945 www WhitakerBrothers com SAFETY INSTRUCTIONS Definition of Symbols and Notes In this manual following names and signs stand for possible dangers Danger This symbol stands for immediate danger threatening the life and health of persons Disregarding these instructions may cause severe damage to health and even serious injuries Caution This symbol stands for an endangering situation that may occur Disregarding these instructions may lead to slight injuries or damage to property Explanations of the illustrations used in the Safety Instructions are given as follows Don t put a hand under the hollow drill bit There is a danger of receiving an injury Don t touch any rotating part There is a danger of receiving an injury Don t bring a hand face hair sleeves of clothes and the like close to the rotating parts of the machine There is a danger of receiving an injury When you change into unusual states like smoke comes out please turn off the power switch of a main part and pull out a power supply plug from a wall socket
Download Pdf Manuals
Related Search