Home

OperationsManual1-1

1. Pan Speed Primary and Secondary axes Guide Speed Primary and Secondary axes normally this is 15 sps for 1X Backlash Primary and Secondary axes if used ONNMNBWNR IMPORTANT NOTE 1 SitechEXE can access multiple controllers at the same time on the RS232 serial cable However ServoConfig cannot So be sure to unplug the modular connector for the RS232 port on any Controller that you are NOT updating with ServoConfig and then afterwards remember to plug it back in IMPORTANT NOTE 2 SitechEXE and ServoConfig CANNOT access the controller at the same time There is only one serial link to the controllers and only one program can control it at atime So if you have ServoConfig up and running talking to the controllers be sure and exit it before trying to have SitechEXE try to use that serial link to talk to the controllers and vice versa One last thing some German Equatorial Terminology to remember if you have a GEM It can 33 of 236 be confusing talking about which side of the pier the telescope is on so we have created some terms for this manual If the scope is physically on the east side of the pier and you are looking at something in the western sky side of the meridian then we will refer to this as looking west If the scope is physically on the west side of the pier looking at something in the eastern sky side of the meridian this will be called looking east There will b
2. Note When communicating to the second controller using ServoConfig you MUST unplug the communication link to the first controller and vice versa ServoConfig can only talk to one controller at a time SitechEXE can talk to both at the same time SitechEXE and SerovoConfig cannot talk to the same controller at the same time If you find that the focus In and Out commands are reversed you may have this focus motor working the wrong way Use ServoConfig and reverse both the Azimuth RtAsc Motor direction and Motor Encoder Direction From the main SiTech window you can call up the focuser window by clicking on the Focuser button Two Focusers If you want to use two focusers one for the main scope and one for the guide scope check use two Sitech focusers in the Config menu in SitechEXE Use ServoConfig to configure the Alt channel in the focuser controller for the Guider focuser and set guide pan and slew speeds in ticks per inch or per mm Swap between the two focuser windows in the Telescope Focuser Window Parameters Tab Be sure the main scope focuser is plugged into the Azimuth channel and the guidescope focuser is plugged into the Alt channel on the focuser controller 114 of 236 8 1 DESCRIPTION OF THE FOCUSER WINDOW The Window has an upper area and a lower area The lower area has three tabs to change the contents of the lower area a Absolute Position exactly where the focuser is located i Telescope F
3. Option Explicit Dim Chart Dim ObjInfo Dim CRLF Dim RARate Dim DecRate Dim SPS2DecRate Dim SPS2RaRate Dim Scope 145 of 236 Set Chart CreateObject TheSky6 StarChart CRLF Chr 13 amp Chr 10 GetObjectToTrack Sub GetObjectToTrack Dim x Dim y Dimi Dim Result Dim Didit x Chart WidthInPixels 2 y Chart HeightInPixels 2 Set ObjInfo Chart ClickFind x y The property value is in in seconds of right ascension per lt I gt sidereal second lt I gt To convert a given rate in the more common units of sidereal seconds per UTC clock second multiply the value by 0 9972695677 the number of UTC seconds in a sidereal second then set the property Please note that these units were chosen for the Telescope V1 standard and in retrospect this was an unfortunate choice However to maintain backwards compatibility the units cannot be changed A simple multiplication is all that s needed as noted SPS2RARate 0 066666666666666666666666666666667 1 00273790797 SPS2DecRate 1 0 Didit 0 for i 0 to ObjInfo Count 1 ObjInfo Index i if ObjInfo PropertyApplies 77 then Didit 1 RARate ObjInfo Property 77 DecRate ObjInfo Property 78 Result MsgBox Click OK to Track The Object 1 SiTech Offset Tracking if Result 1 then Set Scope CreateObject SiTech Telescope Scope Connected True Scope RightAscensionRate RARate SPS2RaRate Scope DeclinationRate DecRate SPS2DecRate Scope Conne
4. Options Click on Show Image in PlateSolveXP to see the image with the catalog stars and targets marked This is especially useful if PlateSolveXP doesn t solve It could be smeared star images if the controller hasn t finished it slew Click on STOP in the PlateSolveXP window to stop looking before the 999 FOVs and move on to the next point If you click on Keep Window Open in PlateSolve script will stop till window is closed then it will resume else the window will close in 7 seconds The active script step is highlighted in the scrolling script window If active step scrolls out of sight simply click in scrolling window to have it re appear If you notice the focus has gotten bad mirror shift etc click on the PAUSE button in the script window NOT during a slew Then you may control the camera from the camera s w and refocus then remember to exit focus mode 203 of 236 When script completes script status window will indicate o If you are using Nebulosity you will have to abort the script abort button in Nebulosity Restart the script when done o When re focused and ready to resume script click on UnPause button in the script window eee stopped Scope stays pointed at last Cal Point location Close Script Window Open PointXP window in Sitech Scope Tab it s the large button that shows PointXP stars Loaded number Click on Display Cal Stars and edit out any stars with large er
5. SiTechEXE is actually a set of program files that run together to provide the extensive features available The support files are loaded into the C Program Files Common Files ASCOM Telescope SiTech folder Updates to later versions are just the SiTechEXE exe file plus occasionally additional program feature files that need to manually be placed in the above folder Any new full initial install version will incorporate all the cumulative changes and additional files for all the features available Simple updates to use AFTER you have done a full install can be downloaded from https sites zoogle com a sitechservo info home downloads I recommend that you create a shortcut to SitechEXE on your desktop if the install program did not automatically do that Go to the Sitech folder mentioned above and right click drag the sitechEXE exe ICON to your desktop and select create shortcut do not LEFT click and drag or you will move the program The program itself needs to stay in the Sitech folder You should probably also make a shortcut to the ServoConfig exe program also while you are 32 of 236 thinking about it if you have not done so previously It s in the C ServoConfig folder The two desktop ICONs look the same the titles are different This was done to try to confuse you 3 3 STARTING THE SiTech TELESCOPE DRIVER SiTechEXE Generally speaking before you connect using your planetarium software you should get the driver
6. 0 00000 we blind track if equ if above horizon we init and track Did this for both clicking the track button as well as first ascom track command 2 made better debug reporting not just from top window 3 Fixed bug created when detecting init on wrong side alt az s wouldn t work 4 Made slewing stop when any direction key pressed on real handpad 5 Fixed debug mode not working properly FAs FAS FAS 2g E KE K E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2k K ok 0 37AB Made reporting of parked position smarter for POTH and TheSky EEEE KE K ig K K K K K K K K K K K K K K K K K ig K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K 0 36 1 Made Top Right key pause unpause script 2 Detect init on wrong side GEM give choice to abort init 3 Made the track ascom or button click work on equatorials by doing blind tracking before initialization 4 Made Color File Scheme 5 Added Debug Mode to config EEEE E E E E E E K E K E K K K K k K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2s K K K K 2 K K 0 35 1 Now we can t slew if parked We send message instead 2 if receive a track commnad before init zed we ignore if not previously parked 3 Made the refraction routine slightly more accurate when going from apparent to real ra dec 4 Button for GEM FLip 5 Expanded range f
7. 8 of 236 USING the system out under the stars to get down using the basics before you try to also come to grips with the more powerful capabilities the system has to offer e When you are comfortable with operating the system using your PC and SitechEXE then it is time to start into the advanced operations Use the OPERATIONS manual for this There are some advanced capabilities that make more sense than others to incorporate first such as using the SitechEXE tools to build a model of your mount to dramatically improve both tracking and GOTO accuracy and using the Periodic Error Correction capability to eliminate periodic error in the RA drive for an equatorial mount If you need to go back and change any configuration information in the controller as part of using any of these advanced capabilities the OPERATIONS manual will give the reference to you where to go in the SETUP manual e There are several appendices in each of the manuals that are related to either setup activities or operations activities For instances graphics of how the components are cabled up and the pin outs of the various cables are in the SETUP manual The circuit diagrams for advanced capabilities like an optional autosync detector for the periodic error correction routine and a sensor for the thermal compensated focusing capability are also in the SETUP manual appendices The OPERATIONS manual appendices contain sections on how to configure several of the more
8. Added ServoClockCal to calibrate mSec clock in controller KEKEE KE K E K K K K K K K K K K K K K K K K K K K K K K K K K K K 0504A Fixed Encoder Threshold input Lowered gain on tracking rates 050B Added Air Mass to Numbers Added LST to Numbers Now we Stop Tracking if below alt limit Added No Wrap option on azimuth ra Added Drift Calculator Added MountTerms Enable to config Fixed slew ending bug Fixed IgnoreAl and TickMan both bits set 050C Added Supervisory Pot control including calibration in the configuration 050D Fixed bug when trying to select or not use a star when scrolled down in window Added Enter on handpad loads offset init and Escape loads a cal star init Now once CalStar loaded then all other inits are load cal stars until offset init is performed 050E Added All and None buttons to PointXP display Added RMS and Peak error to Init screen 217 of 236 Fixed if PXP Mount Error Terms not in config takes all as 1 Fixed handpad oscillation OSOF Unpark Waits until PXP is fully built Fixing oscillation still If error too much then we warn to allow inits Fixed Drag Mode Bug 050G and H Made alt az display in pointxp display with gotos added 4 more terms to do with Alt vs az thanks Dave Added Last button to pointxp display Added Wait4 comm on init Improved by about 5 arc seconds peak with short run didn t center Made PXP Modal OSOL Fixed Tick Managment bu
9. Make auto z3 calc instead of alt offset on 3rd star or keep alt offset same as lst two Made feature to update motors or encoders with the value from the encoders or motors 227 of 236 Stuff related to GEM s Smart First Init uses hour angle of object to decide east or west Added separate offset for east side Fixed meridian flip Fixed guide bug on east side East side inits East Side Z123 with calculations FAS FAS 2S 2g 2g 24g E E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2k K K 0 14 Sent out a couple in various states jumping to 0 15 KEKE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 0 13 Fixed Meridian Fuzzy stop tracking Fixed autoinits to be offsets but if a load init happens make the default be load inits unil 3 done Fixed Version 1 8 errors popping up again deleting down to 1 init force lat long etc Start moving the R A to south when performing an auto meridian flip EEEE E E K E E K E K E K 2g 28 K k K K K K K 2g K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2s K K K K 2k K K 0 12 Fixed possible bug in Distance math blowing up Made it impossible to do slewing or even error correction if no receive from the controller KKK 2k K of of K K K K K K K K 2k K of K of K K K K K 2k ok K K K K K K K K K K ok K K K K
10. XI Returns the Integral XD X Derivative 0 32767 XD Returns the Integral XE Maximum position error limit before servo turns off 0 32767 XEL Returns position error limit XE Returns the position error of the servo XO X Output limit 0 255 XO Returns the PWM output of the servo 0 255 XC X Current Limit 0 240 0 2 40 amps XC Returns the X motor current 100 240 MAX XM X to manual mode the number is the PWM value 255 to 255 XA Xto Auto mode XN X Normal Stop ramps down then stops Automatically clears when new position is given XNT Just like XN except when it slows down enough it starts tracking in the DragNTrack or SlewNTrack mode XG X Emergency stop stops immediately XL Set Integral Limit 0 24000 XL Returns Integral Limit XB Number sets the servo bits like direction etc 0 255 XB Returns current X Bits Value 178 of 236 XZ Forces the scope encoder position to be equal to the number 2147483648 to 2147483647 XZ Returns the scope encoder position The following commands don t have a Y command only X They affect both servos XK Returns the handpad info in Decimal XH Returns the temperature of the CPU chip in deg s F XV Returns the firmware version 10 XJ Returns the motor power supply voltage 10 please divide returned number by 10 XQ Resets the servo system both XU Programs factory defaults into the flash ROM XW Werites the configuration of both the x and y par
11. 0 26 Fixed bug where no comm after controller re boot It was the millisecond timer Fixed bug in averaging PEC with slopes Changed PEC file system to be doubles instead of ints KEKE KE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 0 25 225 of 236 Fixed bug in Drag Mode Configuration screen Added Offset Tracking Rate Control FAS FAS FAS 2g 2g E E E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2 K K 0 24 Added to the PEC PEC Fixed misc user interface added filter KKK 2k ok K of K of K K K K K 2k K of K K K K K K K K K K K of K of K K K K K K K of of K of K K K K K K K K of K K K K K K K K K K ok K K K K K K K K 0 23 If unpark commanded from ascom at 1st we let user decide whether to unpark or not Made a button to inspect the inits Added Separate AdjustEncoder screen changed all those buttons on the features to one button Added PEC control and status EEEE KE E E K E K K E K k K K K K k K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2s K K K K 2K K K 0 22 Added tooltips to all windows Added the 3 ascom CommandBool CommandBlind and CommandString methods Still need to TEST Made the Drag Mode be optional with or without encoders EEEE E E E E K K E K E K K K K E K K K K K K K K K K K K K K K K K K K K K K K K K K
12. A Simple Offset Init simply orients SiTech to the overall sky If polar alignment is accurate you will be able to GoTo objects all over the sky If polar alignment is off a bit you may need to update the controller with another Sync when you slew to other parts of the sky The SiTech controller will provide accurate within a couple arc minutes slew positioning as long as the encoder tick settings are accurate and the sync is accurate If you stopped the timer to verify the information on the screen you can continue with the Offset Init by simply clicking on the Simple Offset Init button followed by clicking on the OK button Do NOT forget to click on the OK button But before you do that be sure that if you have a GEM that you verify which way the telescope is looking looking east or looking west and make sure the appropriate Radio Button at the bottom of the screen is selected Your tracking may really get weird on you if you don t remember to do this So if you have a GEM and you are not a speed reader it s a good idea to always stop the timer to verify the right button is selected for your first init After the first one unless you do a meridian flip the software will usually have it right There are a few other things on the init window to learn about Obviously the Init RA Dec Alt Az and hour angle information is pretty straightforward The scope latitude and Longitude information ar
13. Argo Navis If you don t have telescope encoders set the Sidereal Technology Servo Controller in the SlewNTrack mode If you do have telescope encoders put the Sidereal Technology Servo Controller in the DragNTrack mode Please read the section on DragNTrack and SlewNTrack for setting in this mode Be sure all of the parameters are set properly for proper SlewNTrack or DragNTrack operation Be sure the telescope tracks reasonably accurately in the auto track mode Setting your SiTech to be in the DragNTrack or SlewNTrack modes has several advantages In addition to proving that all the telescope encoder resolutions and directions are programmed properly it has the advantage that if you want to simply track without the Argo Navis on a particular evening you can initialize on the Celestial Pole and then you can have tracking without the Argo Navis or if you connect the Argo Navis you can have more accurate tracking and also GOTO s Important If you don t have external encoders you MUST select the Ignore Encoders option so the controller will ignore the external encoders 2 4 3 Operation of the Argo Navis OK now connect the Sidereal Technology Servo Controller to the Argo Navis using a serial cable fabricated as shown in appendix E of the SETUP Manual As soon as you press both top buttons on the handpad ESC and RTN at the same time the communication with the Argo Navis will begin and the Drag
14. Made option to save all of the fits file on a PXP run gt Fixed the Scope Emulator I broke a while ago gt gt gt KKK 2k ok K of K K K K K K K 2k ok of K of K K K K K K K K K K K K K K K K K K of K K K K K K K K K ok K K K K K K K K K K ok ok ok ok K K gt O55F gt At Rowe Ville gt Made the PXP terms be saved and restored with PXP file gt gt ok oi 2k 2k ok of of of of K K K K K 2k ok ok of of K K K K K K ok ok of of of K of K K K 2k ok of of of of of K K K K K ok ok of of K K K K K K ok ok ok ok ok ok K gt O55E gt Added the 500k and 320k gurleys for altitude gt gt Made the TPR be redundant reads from controller since no CS s gt Also took away the decision to accept them 211 of 236 gt gt Made the feedback for the ascitCSMode be from the controller gt This makes it impossible to send a command and not have it take effect gt because of bad communication gt gt 055D gt In the controller firmware version 3 6C the return binary has an gt address character it sends first gt it is A8h controller address gt Home Added the Homing function finally gt gt gt 055C gt We now clear the receive buffer after end of transmitting characters gt gt OSSB gt Fixed a couple of AsciiChecksum bugs gt changed label on the track button gt Let up of move on virtual handpad will stop when scope is not tracking gt SlewToAltAz in scripting w
15. Running PlateSolve from the Command Line Call PlateSolveXP from the command line as follows Path PlateSolveXP exe RARad DecRad XSizeRad YSizeRad MaxRegions Filename RARad The approximate RA in radians of the image center DecRad The approximate declination in radians of the image center XSizeRad The approximate X dimension of the image in radians YSizeRad The approximate Y dimension of the image in radians MaxRegions The maximum number of regions the program will search before it gives up and terminates Filename The full path and filename of the image file PlateSolveXP creates a file with the same name and path as the input image file The extension of the new file is apm for Automatic Plate Matching This file has three ASCII text lines The first line has the format RARadCenter DecRadCenter ReturnCode If plate solving was successful then RARadCenter DecRadCenter is the calculated center of the plate in J2000 0 coordinates in radians and ReturnCode will equal 1 If plate solving was not successful then RARadCenter DecRadCenter will equal 999 999 The return code will be one of the following ReturnCode 1 Valid plate solution ReturnCode 0 Unanticipated problem during plate matching ReturnCode 1 Maximum search limit exceeded ReturnCode 2 PlateSolve was terminated by user ReturnCode 10 Can t open input file The second line has the format PixelScale Angle Stretch Skew Num Pix
16. Setup Silech ASCOM Driver VO 54L Telescope Info Mount Info Scope Encoders Miscellaneous Ascom and Troubleshooting Focuser Rotator Potentiometers Camera Control Software in SiTech Scripting Comm Port Coml C None FOV Calculator Comm Loop Time mSec 250 Camera x Pixels 1024 C MaximDL Mute SiTech Sounds J Camera Y Pixels 768 C AstroArt Nutate Coords I Ee x Microns per Pixel 9 i i 9 CO Nebulosty Y Microns per Pixel Telescope Focal Length 1 549 Meters Refraction On T gt CCDSo Calculate Field OF View Temperature C Aberrate Coords l Camera FOX ArcMins Camera FOVY ArcMins 20 16 Load Backup Config File Save Backup Config File ll Red J Colors ColorFile SiTechCol OK Cancel Help The left side of the miscellaneous tab provides the capability to select the comm port for the PC to use to communicate with SitechEXE If you are using a serial USB dongle and do not know what comm port to select go to Start Setttings System Hardware Device Manager and click on Ports It should indicate what comm ports have been created If not look at Properties for the comm port and it will be shown in there If you use a usb serial dongle we recommend that you use a good quality one and use the latest drivers available from the manufacturer s website Pressure mBar Metric Units Iv The Comm Loop Time is set in milliseconds 1000 milliseconds 1 second A good starting settin
17. This tabbed page provides the ability to enable the use of these Supervisory Pots and once calibrated to provide limits and if the polarity is backwards allows you to correct that Details on how to set up and use this capability is in the Advanced Features section of this manual 4 12 CONNECTING WITH YOUR PLANETARIUM SOFTWARE After the driver is running start your planetarium software and then select the ASCOM 71 of 236 telescope type and the SiTech driver Configuration can be done at this time or also can be done from within the SiTech Telescope Driver at any time After selecting your planetarium software s Connect command you should be up and running and ready for initialization You can connect with any Planetarium or camera software that supports ASCOM at any time Multiple connections are just fine Every ASCOM method and property is supported SiTechEXE has a built in hub so you do not need to run POTH with ASCOM Examples of how to set up a number of the more popular ASCOM compliant planetarium programs are in the appendix B of this OPERATIONS Manual 4 13 EQUATORIAL AND GEM INVERT BUTTON SETUP Use the Invert buttons in ServoConfig Edit Parameters Motor Encoder Tab to change the encoder and motor direction as needed to make your mount move in the proper directions for the hemisphere you are in See the SETUP manual section 8 3 for more details 4 13 1 Northern Hemisphere Setup 1 While usi
18. after arming Click on Sync in ECU STOP timer in Init Window Tweak star position Top Left Cal Star Top Right Offset Init Radius FOV of high power EP Speed DPS Init with Top Left DOWN For Low Pwr EP Top Left UP During Search Faster Top Left UP Slower Top Left DOWN Reverse Direction DOWN Return to fwd UP Pause Search SPD Resume UP DOWN or SPD Exit Search LEFT or RIGHT 205 of 236 Appendix I PlateSolveXP PlateSolveXP by Dave Rowe Version 1 08 2009 07 18 PlateSolveXP extracts stars from a monochrome FITS SBIG JPEG or BMP image file and attempts to match the extracted stars to a custom catalog created from the Hubble Guide Star II Catalog the Tycho Catalog the SAO Catalog and the Yale catalog of bright stars The plate matching routine is based loosely on the algorithms developed by Valdes 1 et al 1995 with many additions and modifications of my own In most cases the program will successfully plate match images larger than 80 arcminutes 2 Smaller images may not have enough catalog stars and success will depend on the density of stars in that region of the sky Images that have been highly modified in a non linear fashion including saturation may not plate match The program can be used in one of two ways from the command line or as a stand alone windows application To run it as a normal windows application just start it in the usual way with no command line parameters
19. and will work its way around going from low to high to low etc This will help you manage your dome slit also since it will always be rotated in the same direction If you have an Alt Az mount have the 3 star in the NE or NW since it will start in the NE if the mount is aimed to the East and NW if the mount is aimed to the west This protects for not slewing thru due north in case the no wrap option is checked for an alt az e When the CalPointsXP graphic comes up click on keep it up so you can watch to see where the next init point is to be ready with the dome If you are having trouble keeping up with the dome movements simply increase the Mount settling time for the scripted PXP run It will do the slew and then wait for the settling time allowing you to make sure the dome is positioned OK Probably will have to use trial and error to pick a long enough time depending on the hassle quotient for moving your dome Remember to set the settling time back to something shorter after the PXP operations are done or it will wait that long to tell you a GOTO slew is completed for normal GOTOs afterwards e Make sure your system is focused well BEFORE you start Its hassle to interrupt things and you can lose your PXP run having to stop and re focus and if you get any image shift when focusing you just trashed your model If you do lose focus during the run do not click on pause during a slew Click on pause during the time
20. change the Platform Goal from positive to negative or vice versa Problem The equatorial mode works but the stars drift in Right Ascension Solution Check for slippage if a roller drive Also check the Equatorial rate using ServoConfig Problem I have a Gurley high resolution encoder on my RA axis but when I turn it on to use with Tick Management my mount tracks way too fast yet doesn t show the RA is changing in the SiTechEXE display Solution Check for slippage of the Gurley encoder and the RA servo motor drive More than likely the settings for the servo motor ticks per rev are set for Sidereal rather than Solar The ticks per rev must be very accurate Check your settings carefully The Gurley is so accurate that small errors in the other settings can be magnified by the calculations SiTech uses to regulate tracking motion Argo Navis Mode Troubleshooting Problem The Argo Navis mode doesn t work at all I pressed both top left and top right buttons simultaneously The encoder values don t change on the Argo Navis when I move the scope Solutions Controller firmware must be at least version 1 6 Argo Navis firmware should be at least 1 1 6 Check the serial cable Check that the SiTech controller is configured for Argo Navis Check that the Argo Navis Com Port is set up to run the SiTech command at startup Check that the Argo Navis serial port is set for 19200 baud Problem I don t have encoders on my s
21. etc etc etc then guiding for absolutely perfect images is going to always be required The Gurley will simply assure that guiding will only have to correct for secondary effects and not the primary effects from bad gears etc And this is exactly what Don and I have found with our systems The Gurley specifications state they have an accuracy or error of up to 30 arc sec for the 5000 line encoders we are using You won t see a jump of 30 arc sec between any two lines but it means the position when you have turned by some amount 45 90 170 or 280 etc might be off by up to 30 arc sec When you complete 360 you should be back on the same line with no error In addition if the encoder is not totally concentric with the axis of the telescope that runout error will also add to an error like the gurley has internally Now an error of 30 arcseconds after 180 degress of rotation is in the noise but if your mounting is only say 0 002 inches out of being perfectly concentric with the axis that will introcuce about 12 arc MINUTES of error in 180 degrees of axis rotation This is NOT unique to Gurley encoders by the way its just we are demanding such unreal accuracy that very small things can disrupt that ultra high accuracy The good news is one of the correction terms in PlatesolveXP the modeling program by Dave Rowe that is built into Sitechexe can actually correct for this eccentricity However you need to do everything you
22. if you re doing a run of Cal Stars Wait until you re done before you adjust the clock 5 2 14 Handpad SlipMode The checkbox on the Features Tab screen labeled Handpad Slip Mode is used when using SitechEXE with a satellite tracking program like SatTracker It allows you to adjust the tracking of a satellite without telling SatTracker that you made the adjustment since satellite tracking adjustments are actually time adjustments If not doing satellite tracking leave this un chcecked or it will screw up your normal handpad operation 105 of 236 5 3 Config Tab 5 3 1 Change Config Potentiometers Tab Setup Silech ASCOM Driver V0 54L Telescope Info Mount Info Scope Encoders Miscellaneous Ascom and Troubleshooting Focuser Rotator Potentiometers Reverse Supervise RA Az I Reverse Supervise Dec Alt I Use Supervisory Pot RA Az l Supervisory Window RA Az Use Supervisory Pot Dec alt T Supervisory Window Dec Al OK Cancel Help Telescope Mount encoders are digital devices that are intended to be read out by digital interface hardware However sometimes it s possible for all those digits to get messed up This is especially important when using a system via remote control So the ability to use an analog device a potentiometer was added The idea is to mount it like a normal encoder would be mounted and the controller simply sends a voltage out to the pot and measures the resistance reading whic
23. pulsar while in the equatorial mode You can configure the equatorial mode to automatically run this motor at the proper speed Dan Gray reports that he tried this and succeeded His report follows A group of about 8 of us were able to SEE the pulsar fade in and out using this approach We were using the 61 inch Kuiper telescope near Tucson Arizona so I dusted off my pulsar detector and took it along It was fairly easy to see the pulsar in the 61 without using anything at all but when the chopper was in it was harder to detect Even with the 61 it was challenging but everyone that tried was able to see it 22 of 236 Pictured above is the 61 Kupier telescope and the group of observers that used the chopper as part of their observing time Dan Gray is second from the right If you do try this please let us know we would really like to hear about it 2 4 USE WITH AN ARGO NAVIS It is possible to use the Sidereal Technology Servo Controller in the GoTo and Tracking mode using an Argo Navis Digital Telescope Computer The Argo Navis needs to have version 1 1 6 or later installed in its firmware You can download and upgrade either or both units by visiting the appropriate website The telescope encoder information comes from the Sidereal Technology Servo Controller instead of the encoders themselves There is only one cable connected to the Argo Navis and it is the Serial Cable See Appendix E in the S
24. 09 50 Dec 57 09 50 Dec 57 09 50 Dec 57 09 50 Tabbed Area Each of the five tabs changes the information and controls in this area Common Area This area is the same and does Dec 57 09 50 Focuser Field Rotate Motors Automatic not change when different tabs are selected Focuser Field Rotate Motors Automatic Focuser Field Rotate Focuser Field Rotate Motors Automatic Focuser Field Rotate Motors Automatic Motors Automatic The vertical panel will come up and be docked to the right side of your screen If you do not have a serial port configured yet on your PC either a native port or one via a USB serial dongle or if the serial port you have is not the one currently selected in the configuration page the program will alert you it cannot configure the serial port Click OK since we will be setting that up in the next step reference the SETUP Manual to set up a serial link to the controller Normally after the comm port is set up and SitechEXE comes up and finds the controller assuming it s powered up this panel will automatically minimize itself down to the task bar at the bottom of your screen No there is NOTHING wrong The ASCOM standards require screens do not stay up in your way even when you really want them to So we have to learn to deal with it Simply click on the icon in taskbar at the bottom and it will come right back Once the comm port is set up
25. C BAS Telescope Position txt A C Hide Server window 5 Close all windows including the TheSky Telescope Setup window by clicking OK or Close Do not click any Cancel buttons This is a VERY important step 6 Make sure both your telescope and TheSky are set for the same geographic location and time When you initially load TheSky it defaults the location to Boulder Colorado and Mountain Standard time When you are using TheSky with SiTech you should have TheSky set for using Computer Time and the computer clock should be set as accurately as possible Operate SiTech with TheSky In TheSky Telescope menu select Link gt Establish You could also link to SiTech using the ICON for Telescope link When you are successfully linked you should see the cross hairs indicating where the telescope is pointing These crosshairs will move as you command any slew pan or extended guide movements with your telescope sh2 171 sky TheSky6 File Edit Yiew Orientation Data Tools Telesc DEH Be Sew t eez a o xe 1x real time vj u dimpr gt 167 of 236 gh2 471 sky TheSky6 Baa DSH BAe SEW tte He eeeviae ala xe a o LEED e ee testing via be os a The above display shows Sitech connected to TheSky Coordinate Settings TheSky does normally Cook the coordinates it uses so you will need to tell Sitech NOT to do that by deselecting nutation precession and refr
26. Guide Rate to the controller XXJ Stores the PicServo Timeout Value to the controller Seconds XXQ Turns off or on the digital outputs of the Radio Handpad Reciever XXN A zero turns off the Argo Navis mode A one turns it on Version 1 6 and later has the following XXK Local Search Alitude Distance XXM Local Search Azimuth Distance XXO Altitude Backlash XXP Azimuth Backlash 179 of 236 When the controller receives a Q as the first character in a line it responds emulating the Tangent Q protocol The encoder resolution is always 18000 the controller uses the configured values for encoder ticks per revolution for the Scope Encoders and converts it to 18000 OAAR Puts the servo into the PicServo Emulation mode no CR required See http www jrkerr com psdata pdf for a description There are some items different all motion control is the same The differences are descibed below The following two ASCII commands with Binary data are for reading and controlling the servo controller in a very efficient manner They have been added at version 1 5 of the controller firmware XXS lt E gt The controller responds with four long ints of position then other bytes for keypad status X and Y Bits and other bits as follows Byte 0 3 Current Altitude Dec Motor Position least significant byte first Byte 4 7 Current Azimuth RA Motor Position Byte 8 11 Current Altitude Dec Scope Encoder Position Byte 12 15 Current Azim
27. In oe 34 Matched 18 Stop Show RMS Difference 0 483 Search Image wy Approximate Image Center r Approximate Image Size RA 013644 4 Ser 51 x 38 arcminutes 154713 Search Limit Edit i f Regions 999 Parameters el ear C8858 _ PlateSolveXP requires a digital camera on the scope and the star catalog database available for download at http siderealtechnology com APM zip The Zip file is nearly 600 MB The data file must be placed in the C Program Files Starry Ridge APM folder for PlateSolveXP to use them Place the file PlateSolveXP exe in the Sitech folder PlateSolveXP works with images from about 8X10 arcminutes to roughly 10X10 degrees Images that are smaller than 75 square arcminutes may not encompass sufficient catalog stars for a positive match The catalog contains stars to approximately magnitude 15 The program is very robust and never produces a false positive It requires at least 10 extracted stars 8 catalog stars and 5 matched stars The background is automatically removed so vignetting and or high background brightness do not normally cause difficulties If you run PlateSolveXP standalone you will need to enter the RA Dec and Camera FOV If the RA Dec is in the FITS header keywords PlateSolveXP will read the coord from there Currently as of version 1 13 this works with MaxImDL but not AstroArt4 since AA4 uses a different format for the RA Dec keyword This is planned to
28. K 0 42 1 got rid of suspect wrong init when doing inspect inits 2 Changed the IC and NGC Text boxes got rid of buttons 3 Fixed Some scroll files displaying the coordinates in the info box 4 Can now control two focusers with 2nd controller instead of just focuser rotator 5 make space possible between M and number in scripting and lower case m n i s EEEE E E 28 K K K E K K K 2g K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2s K K K K 2 K K 0 41 Finally fixed the GEM Parking bug Made a DataBase You can now GoTo or Sync on NGC IC and Messier objects as well as 294 named stars Also a scroll file is available to step through 221 of 236 Coordinates can be specified in the scroll file or also M N and I can be used followed by the messier ngc or ic number Made Scripting be able to use M N and I followed by number for coordinates example Slew M1 Pan NGC7331 0 08 Pan 11300 FAS FAS 2S 2g EKE E E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2 K K 0 40 Fixed the init window focus problem created in 039 Added Scope Alt and Scope Az to Numbers Added armed indicator to pec screen as well as sync detector Extended time that the SiTech dll waits for SiTechExe exe to start Add icon for init and script windows Prevented SiTechExe from running twice Made comm port changeable on the
29. K K K K K K K K of K K K K K K K K K K ok K K K K K K K K 0 11 Fixed Fuzzy Meridian bug Fixed backlash on declination hunting Changed default init to offsets clicking OK and auto both do offsets now Won t correct for position during a forced TakiTimer FES FAS FAS 2g 2g KE E E K K FAS K K K K K ig K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K 0 10 Added ParkMatrix and LastMatrix fixed bug about start tracking from non initialized Stop tracking when end of fuzzy Only GEM can have options on east side Reversed Alt Buttons and on screen buttons when looking east Added AutoGEM Flip FAS FAS 2S 2g EE 2g E E E E K E K E E 2g E K E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K FK K K 228 of 236 0 09 added gem force of pierside on init window KEKE K KE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K K og K 0 08 Added WillPierBeWestLookingEast double ra Added all GEM functions except stop tracking at fuzzy and auto gem flip KEKE KE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 0 07 Sent to Andrew and John Ott 3 25 06 Added InTimer to Taki Timer and made all of them ints instead of bools so in case left set we reset anyway made de rotator track
30. MaxImDL AstroArt PHD etc are examples of autoguider software that is ASCOM compatible This approach does not require anything extra no cables or relay boxes etc Because of this Dan Gray occasionally refers to ASCOM guiding as wireless guiding NOTE Most other servo control system cannot support ASCOM guiding since they end up with significan delays in their responses to the ASCOM guiding commands However Sitechexe does not have any tangible delays with this approach and is actually the cleanest approach to use The controller does not actually even go into guide mode Instead the specific ASCOM guiding commands are acted on directly by the system If you run your imager on one computer and your autoguider on a ae computer you will need to run the autoguider on the same computer that is connected to the sitech controller for ASCOM guiding is to be used From a generic standpoint to setup and connect to your autoguider program in the location for connecting to the telescope look for something that says an ASCOM telescope Selecting that type scope will result in the ASCOM Chooser being displayed and you simply scroll down and select Sitech Then click on Connect as you would for connecting to any telescope That s it ASCOM Guiding uses pulse guiding in case you need that info for your autoguider There are two options for ASCOM Pulse Guiding in the Config menu Config Tab Change Config Button Ascom and
31. N C Slow Focus our N Joe out Jog Dist 0 0100 Enable Handpad HP Jog HP Slow HP Fast Temperature Comp ON Already Focused I Temperature Comp ON Move To Focus Reversal Amt Focuser Park Location Scope Initialize Focuser on Startup f Update Focuser every 60 seconds Use Guider Focuser Focuser Hide Save TA Presets H Colors ag FocuserSetup Sel 0 75 Scope Focuser Out Limit 0 005 Reverse Amount 15 Temperature Slope i ASCOM starts Temp Controlled Focuser in Mowe To Focus mode 7 Focuser has microswitch or optical sensor for initialization Right now Move OUT to change sensor Right now Move IN to change sensor Cancel uonesuadwuoy dwaj suajawese sjulodjag 117 of 236 The In Limit and Out Limit are the absolute limits for the focuser It will not move beyond these limits except possibly while trying to zero with an absolute zero sensor Reversal Amt is the amount the focuser overshoots the focus so that it approaches focus from the same direction This should be large enough to overcome any backlash You may specify a focuser park location and whether to use it at shutdown startup With Zero position sensor You are also given the option to use the sensor to zero the focuser at startup Update focuser This determines approximately how frequently to adjust the focuser position for temperature Th
32. Sync Scope This is the button that will cause Sitech to perform an initialization on whatever you had clicked on in this case Vega In this example we need to perform an initialization so click on Sync Scope This will bring up the Sitech InitPoint window with the ASCOM timer counting down as shown in the next screen grab 162 of 236 IMPORTANT FOR GEMs Make VERY sure the correct Looking East or Looking West labeled Keep window up Manual Control and the timer will stop Then click on Offset Init or CalStar Init if you need that type of init and then click on OK don t forget the OK If you do not have MUTE selected in the sitech config screens you will get a voice report that the sync has occurred and the InitPoint Screen will close it will close for manual ops only after you click OK The cursor where you clicked on Vega will change to a circle and the mount will start tracking After the mount was initialized you can perform a GOTO by clicking on your target and in the target s information window click on Center Scope and the mount will slew to the target When it gets there you will get a voice report that the slew has ended Hint I like to give folks Eyepiece Rides to show off my mount s GOTO accuracy Let them stand at the eyepiece and call out a nearby target and you do a GOTO after warning them to not bump into the eyepiece They stay at the eyepiece and watch stars whi
33. Terms And Cal Stars Clear Stars Leave Terms Update Display Polar Axis Alignment Error Move Down 00 07 22 Move Right 00 09 27 fat eee ae Term 0 01 04 27 Term 1 00 03 28 File Term 2 00 00 05 Term 3 00 00 00 Points 16 Load CalStar File with terms Display Cal Stars Load CalStar File No Terms Save CalStar File Nearest la SE CNE cow enw M AltAz Equatorial IV GEM Latitude 29 5745 Instability 1 9 Longitude 95 13 00 Latitude 29 34 28 Baro Pressure 1000 Temp Deg s 26 666666666 Mount type GEM X Time Zone Daylight Saves True Sky Toggle WriteDatafdebug Pointing Error 19 Stars in model RMS 00 00 48 Peak 00 01 19 Calculate Terms Calculate Offsets Only Help Me 5 1 4 Scripted PxP Setup and Configuration Configure camera to provide a FOV of at least 80 square arc minutes of area Focal Reducer might be required Confirm Database files are unzipped and at c program files Starry Ridge APM Confirm following files are in C program files common files ASCOM Telescope Sitech Sitechexe exe CalPointsXP exe PlateSolveXP exe Interop MaxIm dll AARemote dll SiTech hrz User Builds this horizon file with an ascii text editor like notepad For example a simple horizon text file for everything above 15 is 0 15 180 15 Where Data is Azimuth Altitude in degrees No spaces in or after each line or at the end A couple of degrees of margin sh
34. Troubleshooting tab One is Instant Total Pulse Guiding and the other is IsPulseGuiding Always Returns False They are there to help with autoguider programs that wait to send a second autoguider command till the first one is completed The concept for Pulse guiding is simple Instead of sending a command to change the rate for guiding active and then a second command to remove the rate its all sent in one command change to a TBD rate for TBD period of time That prevents a loss of comm from causing the mount to end the guiding command The problem is some ASCOM autoguider programs will not send a 2 command if the mount is still acting on the first one So the Total command simply figures out how far the mount would have moved if each of the pulses were sent over the time specified and instantly moves the mount that distance The result is the mount is never still working on finishing up a long string of pulses with the autoguider sends another pulse command The downside is this approach can cause the mount to jump if the pulse guide command is large enough So if your mount typically needs BIG guiding corrections you will have to see if this option works well for you The IsPulseGuiding false option is there because some autoguiding programs are impatient and query the mount for the status of the pulse guiding activity If the mount is still working off the previous guiding command it will return a true for the IsPulseGu
35. USING THESKY If you use TheSky you can build a simple Windows Scriptfile that will allow you center the object in TheSky and then when you run the script it will get the coordinates and the offset tracking rates from TheSly and automatically enter them in the Offset Tracking rates tool in SitechEXE TrackObject wsf will track an object asteroid moon sun comet etc that is centered on TheSky screen No need to connect TheSky to SitechExe however it s important that you center the object you want to track To center the object in TheSky click on it then on the information window click the center on screen icon Also be sure SiTechExe is already running and initialized The telescope should already be pointed at the object Then just doubleclick the script that should do it To verify click on the features tab of SiTechExe then Offset Tracking and be sure the numbers RA and Dec offset tracking rates read the same as the objects offset Tracking rates in TheSky information window This works on Alt Az scopes too You can download the script from http tech groups yahoo com group SiTechservo files VBS_Scripts Or you can type it using any ASCII text editor type exactly as shown below or simply cut and paste and save it with the filename TrackObject WSF lt package gt lt job id Star Chart gt lt Reference guid 045C03E0 A59C 1 1CE 9D1C 0000E8C4D586 gt lt script language VBScript gt
36. also automatically enter the guide mode if guiding signals appear on the receiver AutoGuider port If you are using firmware version 1 5 or earlier you will need to use the following methods To enter the Guide mode Hold down the top right key RTN and press the Right button flashlight must be off 137 of 236 10 6 3To Leave the Guide Mode Hold down the Top Right key RTN and press the Right button again flashlight must be off 10 6 4 To Increase the Tracking rate Hold the top left key down ESC and press the Up key Repeat process for more increases 10 6 5 To Decrease the Tracking rate Hold the top left key down ESC and press the Down key Repeat process for more decreases 10 6 6 Platform Rewind If using a platform to rewind the platform press the ESC and the RTN keys simultaneously 10 7 USING THE RADIO HANDPAD WITH THE SITECH ASCOM DRIVER There are no special features used with the SiTech ASCOM driver You can center objects as you normally would or manually slew if needed 10 8 MEL BARTELS STEPPER SYSTEM OPERATION USING SCOPE EXE If not ordered from the factory as such you will need to remove the cover from the receiver using the 4 Philips head screws Find the jumper labeled STP SRV Install the jumper toward the side marked STP You will also need to connect a ground wire from the terminal block labeled Ground to the ground of the stepper system There are two terminals provided b
37. at the setting for Supervisory Threshold If that setting is small increase it by a factor of 10 or more Mounts with a lot of periodic error and other gear errors need a setting of several arc minutes to prevent conflict Problem My mount stopped tracking and won t start again Solution If tracking looking west the mount may thinks the altitude is less than the altitude limit This would be a good time to check your computer clock the longitude etc If you are tracking looking east and the scope is pointing near the meridian the mount will stop tracking if the Meridian Overlap is set low In SiTechExe Change Config Mount Info Tab If you are using TM and the position encoders report different positions the mount will stop tracking but 183 of 236 this usually gives you an error message Problem Every once in a while the scope would just start moving rapidly in one axis without any input from me Solution Most likely an encoder or encoder cable malfunction where the controller sees the encoder report a far off value causing the controller to move to the errant reported position Verify by watching the encoder value display and seeing if indeed the numbers go wild This is most likely a cable problem too long too close to interference or connector problem verify that connectors are plugged in snug Problem I sometimes run it without the telescope connected I do this when I want to experiment or practice and it isn t c
38. be sure the flashlight is off Make sure the transmitter hasn t turned itself off If it has you will have to press the SPD key to turn it back on For other Argo Navis problems see the SiTech Controller Document DragNTrack Mode Troubleshooting Problem I initialize on the zenith then the celestial pole but it doesn t track properly Solution Maybe the firmware version of the SiTech controller is version 1 5 or lower If so please upgrade to version 1 6 or later There was a bug in the calculate latitude routine in versions 1 5 or earlier Problem I live in the southern hemisphere and the tracking is the wrong direction I have initialized on the Zenith then the south celestial pole Solution The SiTech controller has no way of knowing which hemisphere it s in when initializing on the Zenith or the Altitude You ve got to set the Latitude to a negative number 189 of 236 using ServoConfig before it will work properly Once a negative the initialization process will always keep it a negative number Problem I know the Latitude is correct but it doesn t track properly Solutions 1 If you ve a clutched telescope check for clutch slippage on tracking Sometimes the clutches will work on a slew but will slip during tracking Double check the encoder and motor ticks per scope revolution for altitude and azimuth Be sure the scope encoder and motor encoder polarity is set up properly You can do this at the main screen of t
39. can to make your high resolution encoder mounting as accurate as possible The same applies for the motor encoders and main gear When you turn 360 and have the correct ticks rev in the software you should be exactly on 360 In between zero and 360 the ticks tooth or ticks can vary Don measured the total error between the Gurley and motor encoder all around his AP1200 s main gear 225 teeth and found the total error is up to 135 arc sec compared to a perfect linear rotation That means the gear teeth may be off from 2 X to many X compared to the Gurley You can see plots of these errors and even see how his periodic error changes tooth to tooth at https sites zoogle com a sitechservo info don westergren s site Home gurley on ap mount 112 of 236 What other errors can there be that the Gurley or any other high resolution encoder won t see Atmospheric Refraction can be a big one Wind I doubt is much of an error problem unless it is strong enough to move the clutch or make the drive slip Wind and structural lack of stiffness or too much spring can make a scope move or even oscillate but the Gurly won t see it Gravity changes while tracking and can cause errors due to focuser sag differential pointing of a guide scope comapred to the main scope again the Gurley won t see it So what good is the Gurley Plenty good It smooths out the errors it can see to sub arc second resolution tracking with the help of the SiTec
40. driver 2 Select whether you have an automatic PEC sensor or not at the left side of the screen 197 of 236 3 Start guiding on a star either manually or with an autoguider 4 Click on the button labeled Arm PEC Record e If you have an automatic PEC sensor wait for it to line up and recording will start automatically e If you don t wait for the worm to line up with your reference and press the top left button on the handpad When recording is started the status textbox on the left changes to Recording During the next revolution of the worm the controller will record all of your button presses e Once the worm revolution has completed The status will go to Idle and you re ready for playback e If you have an automatic PEC sensor wait for it to line up and playback will start automatically e If you don t wait for the worm to line up and press the top left button on the handpad e When Playback is started you will see the status textbox on the left change to Playing Complex but more accurate PEC training Session A complex recording runs several PE cycles and averages them This method is more accurate for most mounts because the gear teeth are usually not exactly alike Averaging many cycles will ensure the recording is for a typical periodic error Here is what you might consider doing for a complex session assuming motor ticks per worm revolution is programmed BRWN Re Select the PEC screen from th
41. enabled it by checking the Use Focuser Rotator checkbox You will not be able to Set the scope to encoders or encoders to scope if you re viewing the Focuser Rotator controller Reading Controller Parameters You basically have to stop the normal communication loop and ask the controller for a specific parameter As this would conflict with normal telescope communication we ve made it possible to only view one of the parameters at a time Simply hover the mouse over the desired parameter and it will read continuously This feature can be very helpful to see what controller volts you have finding mechanical problems in your telescope can be easier by watching the current and other helpful information Problem I finally got a clear night with little to no wind and I am trying gt to tune the servo clock Calibration but I am kind of at a loss to figure it out Can you help please Solution Yes After the controller has been on for at least an hour then you can click on Save ServoCal this will take the new recommended value and save it to config and start using it as well The idea here is the 1 millisecond clock is much more accurate than anything Windows can do on a short time scale however the clock in the computer is much more accurate over long periods of time This feature will calibrate the SiTechExe software to the controller as it will know how far off it gets From my experience this won t change over time or temp so o
42. errors are periodic in nature or something else There is good information on doing this in the PemPro help files For instance the 17 23 sec Gurley Interpolation error frequency and its harmonics show up quite well in Pempro as to the G 11 76 second error due to the worm bearings if they are not running true You can also calculate and include gearbox fundamentals that can show up a problem with your gear reduction if used 5 2 12 Offset Tracking Rates Let s say a new fast moving comet has appeared and you want to shoot it but would like to track it during the exposures Simply use features of your planetarium program most don t have this feature but TheSky does so does Earth Centered Universe click on the comet jot down the R A and Declination Rates and enter them in this window Be sure they are the same Engineering Units if different you may have to convert them The SiTech Telescope Driver uses arc seconds per second of time Now your scope will track the object There are two features here one for doing offset tracking to follow a comet or asteroid and the other is for tweaking the tracking rate s The top two sliders are for doing Offset Tracking and the bottom slider is for tweaking the tracking rates THE OFFSET TRACKING WILL NOT WORK IF IN DRAG MODE THE TWEAKING OF TRACKING RATES WILL NOT WORK IF NOT IN THE DRAG MODEW TheSky software has a feature where if you click on a solar system object the o
43. focuser is started 5 Indicate whether the focuser should automatically move the focuser to the park position upon shutdown If so set park position The focuser will remember the last position at shutdown and assume the focuser has not been moved while turned off The focuser position will be set to this position at startup 8 2 2 First Time Startup WITHOUT zero position sensor 1 Confirm that the out button moves the focuser out If motion is reversed change the direction settings for the controller using ServoConfig exe 2 Click the Parameters tab then the Setup Dialog button Make sure the Focuser has microswitch checkbox is unchecked Then Click OK 4 Indicate whether the focuser should automatically move the focuser to the park position upon shutdown If so set park position The focuser will remember the last position at shutdown and assume the focuser has not been moved while turned off The focuser position will be set to this position at startup 8 2 4 Finishing the setup for all focuser configurations 1 Use the slew and or jog buttons on the focuser window to move the scope to the IN and OUT limits for travel Set the In Limit and Out Limit values on the Parameters tab 2 Set the reversal amount this should be larger than the backlash of the focuser The focuser approaches focus from the same direction except during TCF operation 3 Set the frequency for updating the focuser position based on the t
44. for downloading it is at http www stargazing net astropc Handy Tip Another freeware by the same group of authors is the Virtual Moon Atlas VMA which can be downloaded from http ap i net avl en start and has a very similar user interface that allows GOTO moves from crater to crater on the moon The main screen of CDC looks like the screen grab below Click on Telescope in the command line and select ASCOM for the telescope interface to be used i ace modai i L 19 O7 0 0 ARC HZ Magn 9 5 Cat DSL hip BSC SKY Images ese Help a O 2 S K EGA aie em ea a EA V ASCOM Configuration Panel Encoder Meade none The 4 options at the top of Telescope window that comes up when you click on Telescope in the command line allow you to have the cursor show where the telescope is aimed and after clicking on a target to do a GOTO or a Sync They become active after connecting to SitechExe Clicking on Configuration Panel will bring up the following screen 169 of 236 amp ASCOM Telescope Interface 1 3 Driver Selection Select sit ech Telescope Configure Refresh rate i 000 as About Observatory Latitude 2946 3 Longitude 95 24 26 eer mwe R oef eA E c Abort Slew Help Connect Disconnect Hide Select Sitech Telescope for the type of ASCOM telescope to connect to and select a refresh rate units are in milliseconds so 1000 is 1 second I suggest us
45. get a feel for all the topics and capabilities but to keep from getting lost in all the capabilities this system has to offer we really recommend when you start reading for content you start with the SETUP manual and read through it first It s written ina building block type of approach The idea is to cover considerations about initially building your drive system or perhaps converting an existing drive system to a servo control system and what components are required and what are optional The next part of SETUP assumes you have mechanically installed your servo motors It covers how to get all the required components hooked up to your controller Motors handpad power supply and a serial port to a PC and if your PC does not have a serial port how to use a USB to serial converter dongle to provide a serial port The next step and the majority of the rest of the SETUP manual then covers how to update the controller with the latest firmware to tell it that it is a controller and to update it with the basic required information about your telescope mount It starts with how to install a very powerful program called SERVOCONFIG which is what you will use to send information to the controller It also has tools for helping you measure and set up critical parameters for your system When you get to this point you should be able to actually USE your mount without a PC None of the really cool bells and whistles w
46. in the Tracking Platform Goal 2 3 2 Operation of the Equatorial or Tracking Platform Mode If using an equatorial platform before powering up the controller be sure the platform is fully rewound This will be its home position Upon power up or after a rewind the Right Ascension motor will turn at the configured speed until it reaches the configured goal To rewind press both top switches This is possible at 21 of 236 anytime The servo motor will return to the same location it was when power was turned on at its programmed slew speed rate To Cancel rewind press any direction key If using an equatorial telescope the above paragraph will not be applicable as the platform goal will be set for 10 000 000 or greater To stop tracking press the top right key To start tracking again press it again or press any of the direction keys When the tracking is stopped both LED s will blink off briefly every few seconds version 1 6 of firmware and later Only the new handpad will allow fine tuning the tracking speed To raise the tracking speed press the top left key and while holding it down think of it as an ALT key press the up direction To lower the tracking speed press the top left key and while holding it down think of it as an ALT key press the down direction The up down adjustment will not work if you have set up the local search feature version 1 7 or later of the firmware To enable the UP Down adjust
47. inputs can be read by the serial port on the servo controller and the digital outputs can be controlled by the serial port on the servo controller The inputs could be connected to limit switches or home switches The outputs could be connected to a relay to activate an accessory of some type such as a toaster or a lava lamp There are 4 digital inputs and 2 digital outputs on the receiver If the digital outputs are used there are only 2 digital inputs as two of the pins are shared with the outputs and the inputs For these to be used the servo controller must have 1 6 or later firmware version The digital inputs appear on Y_Bits bits 4 7 To read the inputs issue the command YB lt E gt the controller will respond with the value of the Y_BITS The upper nibble holds the current value of the digital inputs The digital inputs are floating and must be held low for a zero and pulled high for a one No more than 5 volts should be on the inputs or the outputs It may be a good idea to use an opto coupler to use these digital inputs and outputs 5 volts and ground are provided on the I O connector To turn on the outputs the ASCII serial command XXQ is used To turn on output 1 and keep output 2 off issue the command XXQ1 lt E gt 139 of 236 To turn on output 2 and keep output 1 off issue the command XXQ2 lt E gt To turn on both outputs issue the command XXQ3 lt E gt To Turn them both off issue the command XXQO0
48. is to use the information in sections 5 2 6 through 5 2 10 for using the PEC training as you step through the flowchart and the numbers that are keyed to the PEC screen and flow chart Its not nearly as complicated as it looks 175 of 236 Diog ay yya payeisosse a esaay AMEINYO ACSI JOU St mous eOMPIBIOD YIBLNS JION alld aapallog ajid w anpallo9 aaljaayjo5 JQE4pU dd0 NO Aejdsiq ydeig 93d anaba I scn way BAIPaOD a alge way vad 4 anpalloo pahelaay y yan way aanoayiog i gt a v ereenn way Tayng age BAHDEIIOD pahesaay 3d spue wwog UBITISO 4 40404 ejeg uols Og 1040 aqel 93d d 00N aal asid IWAS agd ienuew z aprnoig Jayng 1811014409 aging UAS 33d My ayng all4 93d Jayng ally 3d WOH Yse 4 1801440 49AUQ i Od SEa 176 of 236 SIU s1010 GZ 440 s0suas ourgoiny 934 IAA SSILUSI Ie s14084 ay EY soe as ie QI flls 0 wa eanoayog anes yoeqreld Jad dos 6L SE SE Aae OT s I L way BAHIAYOD a220 g YSE 4 9 PYF Jayo4uo07 ul ajge aaes 8L ayy oy ayng abeiaay anes aayoajog UID eaey noaj pag 1aionuog omg aige PaBereay puas a4 J3d woy rayng ayy peor Lit Q J2J ONUO o jng a4 Wry 3 92 1 J3q pues A bz PF pence amen haa BANOS IOI Jd 2425 Gik yng aug ow age J3d Iau peey Al eo MEES cL BANDON 23d peo pH yeqe 33d WY apea moys ZL ma al woy way aayoajog peo posay J
49. of telescope you have then be sure to click the Properties button to configure the driver for your telescope SiTech v Properties R Click the logo to leam more ad about ASCOM a set of standards for inter operation Belews of astronomy software Cross hair update frequency ms 500 Close If you do not see this window then TheSky is not seeing the TeleAPI dll on your computer If you have the replacement TeleAPI dll in the proper folder then the problem is probably that you need to update your copy of TheSky A fresh install of TheSky either 5 or 6 will not see the Telescope API TheSky5 has update 108 5 17 2004 available at the Bisque Software web site TheSky6 has update 61 1 21 2009 available Both of these updates work well with ASCOM and SiTech 166 of 236 4 Now click Properties in the Chooser which will display the settings window for the telescope type you just chose Make adjustments as your telescope needs Here you can set up to just allow GoTo or also allow several other capabilities with SiTech Server Settings a C Allow remote connections URL of local horizon cancel _ coneat_ Example Remote client capabilities Cl allow sync C allow set park C Allow set tracking rate Allow goto Allow park C Allow focus control C Allow map using Orchestrate or RASCOM C Remote clients use Orchestrate s ImageThenSlewTo command Log current telescope position to
50. offset from current rate by a certain value for a certain time Made the record and play start on segment 0 if not auto sync and it s been synced at least once KKK K K K K K K K K K K KK K K K K K K K K K K K K K K 2 V34B Made the record and play start on segment 0 if not auto sync and it s been synced at least once 0 IS 2g 2g 2g 2g 2s K K K K K K K K K K K K K K K K K K K K K K K K 2 V34C Fixed floating point version mix up gt V34D Added YXO command to read PEC error KKK K K K K K K K K K K K K K K K K K K K K K K K K K K K re V35A added interpolation error correction for Y axis RA V35B added interpolation X and Y Axis for 500k encoders Another attempt to stop tracking as soon as top right pressed Even in SiTechExe argo navis equatorial and dragntrack slewntrack V35C fixed the stack on the altitude encoder V35D Fixed the cleared the DoingBinRec 2 flag after receiving characters 235 of 236 SRR OR EOE 2 RA OR SEO Ae ak AEA HR OR SEE eae RE RR SEE V36A Working on adding a checksum to ASCII commands this only happens after the receipt of a binary command Use bit OSCICN 3 to detect saved a flag Deleted the XBEquatorial flag so we can use it for ASCII cs While in ASCII Checksum Mode a pause of 40mS or more resets the receive ptr Deleted the Internal Ram Transmit buffer This required a re write of LTOA and associated routines All now go to external ram V36C Added one byt
51. only 3 or 4 arc minutes of drift per hour Howard Banich can track an object at 450 power for an hour in his 28 inch scope Important Note If you are using ServoConfig version 0 9 the Azimuth reads backwards from above description when clicking on Get Angles Problem The telescope doesn t track at all sometimes Solutions 1 Press the top right key to turn tracking on or off 2 Be sure it really is in the DragNTrack mode LED 2 should turn on and off every 8 seconds or so If it does this it really is in the DragNTrack or SlewNTrack mode If it doesn t do this the scope is not in the DragNTrack or SlewNTrack mode Problem I m using an old style handpad the one with a center switch and the DragNTrack doesn t work properly 190 of 236 Solution If you are using an old style handpad and you are using Servo version 1 5 or earlier you must enter negative values for the Slew and Pan rates After you check this be sure the scope moves from north to east when pressing the right button and be sure the scope moves up when pressing the up button SlewNTrack mode Same as DragNTrack mode Equatorial Mode Troubleshooting Problem I have an equatorial telescope The telescope tracks fine for a while then stops Solution Using ServoConfig increase the Platform Goal to a number greater than 9 999 999 or less than 9 999 999 Problem The equatorial mode works but the direction is the wrong way Solution Using ServoConfig
52. panel select the Use DragNTrack Mode checkbox Next select the 3rd tab Misc and Tracking In this panel select the Enable Sky Commander checkbox Be sure to save these settings to the controller by pressing the Send Configuration to Controller Additionally since the controller will be turned on and off for most scenarios press the Save Controller Configuration to Flash ROM button so that the settings remain in effect when turning the controller off and on again It is also recommended that these settings be written to a file for retrieval later should the settings need to be recovered later Press the Save This Configuration to File to create the car file This completes the SiTech controller setup Note that it may be necessary to fine tune the SiTech controller later but these settings above are required for use with Sky Commander The physical connections to the SiTech controller are the power motor and motor encoder wires as well as the mount encoder cables See the Appendix F in the Setup Manual for instructions on how to connect encoders to the SiTech controller The connection between the SiTech controller and Sky Commander is the RS 232 Serial Communications cable provided with the Sky Commander The RJ 22 plugs into the SiTech Controller and the RJ 11 plugs into the Sky Commander Be sure to plug the RJ 11 into the smaller port on the Sky Commander it will plug into either one but will only work with the s
53. popular planetarium programs to interface with SitechEXE and on doing some really cool things like satellite tracking and using your CCD camera to write with a star s images There are also appendices in the OPERATIONS Manual that contain Cue Cards A Cue Card is a shorthand checklist to use out under the stars to remind you of how to do things rather than having to try to thumb through the Ops Manual to try to remind yourself of things e And finally both manuals have troubleshooting sections for when things don t seem to go right Hardware does occasionally have issues and gasp even software and the Sitech system has some powerful capabilities to help with the troubleshooting to allow working your way through correcting things 1 FEATURES There are six ways to use the SiTech Controller on your telescope Stand alone In this mode the controller will track your Alt Az telescope using the DragNTrack or SlewNTrack modes It will also track your Equatorial telescope or Equatorial Platform using the Equatorial mode Many users prefer the stand alone mode for truly no hassle telescope tracking This mode is also the most economical It is also the mode that the SETUP Manual will initially have you configure your system to use to allow basic operations and to confirm your system is wired up right and mechanically functional This is also the logical handover point from SETUP to OPERATIONS to learn how to use the most basic cap
54. position Stop Tracking Click on SET PARK to capture park position alt az and RA Dec it is aimed at If mount will be moved before it is unparked accurately aim scope at a terrestrial target when it is at the park position Click on PARK to actually Park the mount OK to power off mount controller and PC To PARK if SETPARK was already set up Click on PARK Mount will slew to the saved Park position OK to power off controller and PC To UNPARK assuming mount had been properly Parked If mount has been moved since parked e If mount was aimed at terrestrial target in park position re center tgt e If mount was NOT aimed at terrestrial target in park initialization when mount is unparked will only be approximate If a PlateSolveXP set of terms was in place when parked they will be re loaded If the mount config was changed since the PXP terms were generated do a Clear Stars and terms from within the PXP screen after starting SitechExe Click on UNPARK e Mount comes up with initialization data that was saved when mount was parked e If init data was accurate when Parked mount is ready for tracking and GOTO Periodic Error Correction For details reference sections 5 2 7 through 5 2 9 Simple PEC Training Session Note It s a good idea to clear out the PEC curve in the controller before you record a new pec curve Use the PECGraph page and click on Clear Pec Table In Controller 1 Select the PEC screen from the SiTech ASCOM
55. right key to toggle the guide mode If you are using the Radio Handpad Reciever and are using the guiding input provided this shouldn t be a problem because the controller will automatically change to the guide mode when a guiding signal is present if using Servo Version 1 6 or later Problem I generally image facing east amp I have the guider calibrated as such But when I flip GEM over to face West I check the box Pier Flip the R A tracks just fine but the DEC will guide right off the frame If I uncheck the Pier Flip box then the DEC will guide but the RA will move off frame Solution Starting with version SiTechExe054B there is an option where you can reverse the guide mode on a Meridian Flip or not in ChangeConfig Mount Info Problem When using MaximDL to control my auto guider should I use the DEC option Solution No SiTech does the equal area panning and guiding so best to keep the declination at zero for MaximDL and any other program that can use the scope declination However if doing the Ascom guiding this is NOT true so in this case best to use the declination option in MaximDL 193 of 236 inouts iver P RF Handpad Recei Appendix G 1YOd O I l 0d O I 1LYOd HAGIND OLNY 3SOduNd 1VYANAD k FUR TAOM 14918 1SIM 9 43431934 GVdGNVH G NMO HINOS L LNNI t df HLYON ges f EEDE GNNOYD v 3 ON PLNON S 2 SLIONS 9 AUVSSAOAN SI a Ti INO AINO WALSAS H3dd3LS S14LuVa NO ND G
56. s init window Press the simple init button Your telescope will now be inited very accurately and you are ready to start building the PXP model On your next init you should press the Load Cal Star button to start the collection process From that point on all the inits will automatically be of the Cal Star type Collect all the Cal Stars that you want in your model Try to sample most of the available sky You do not need to point to particular stars or targets since Elbrus will take care of figuring out the exact coordinates where the telescope is pointing regardless of there been a target in the center of the chip or not During the process you can press the Errors Stars Togle button in PXP to see where in the sky you ve collected Cal Star points And thus ensure that you don t miss any spots From this point on collecting Cal Stars goes like this With the help of your planetarium point the telescope anywhere Pan the scope West and South for a couple of seconds to pick up any mechanical backslash Take short image Elbrus will automatically solve image Press synchronize telescope in Elbrus Sitech will automatically collect the Cal Star position Repeat through 5 ad nauseum End the process by performing a simple init Each time you add a star to PointXP you can check the progress and the quality of the sightings by calling up the PointXP window from the SiTech exe Scope tab 88 of 236 CM PointXP By Dave Rowe Incorporated by p
57. same side of the equator Be sure to NOT cross the meridian on your star near the meridian Also and this is extremely important if you have a GEM please get used to checking the Looking East and Looking West radio buttons to be sure they agree with your telescope mount Your telescope may run away if this is not done properly Fortunately the default is usually correct One more thing if you re using multiple stars on an Equatorial scope you can t put much faith in the scope longitude calculation it kind of blows up Dan totally ignores the scope longitude when using his GEM 54 of 236 4 9 3 Single Star Init If you have a perfectly level scope and you ve set up the Lat Long properly then you can get away with a single ONE Star OFFSET INIT even on an alt az scope When you enter the first star either offset init or Cal Star init point the ascom driver now assumes you have a level scope at the Lat Long specified or a perfectly polar aligned Eq mount It will now do goto s and tracking based on this Dan did an experiment once on his 14 alt az After initing on a few stars Cal Star init points he wrote down the reported Scope Lat Long He then changed the configured Lat Long to these values After doing this he did another ONE star offset init no other inits loaded and his scope became pretty accurate without doing the two star matrix math 4 9 4 Watch your Scope Latitude The Scope Latitude is the l
58. saved your latitude Choice 2 To initialize if your scope latitude is not programmed into the Servo Controller point the telescope at the scope zenith then press and hold the top right key for more than 5 seconds when the LED on the controller flashes fast you may let up Now point the scope at the Celestial Pole Now press and hold the Top Left key for more than 5 seconds when the LED on the controller flashes fast you may let up Your scope is now initialized and the DragNTrack or SlewNTrack will be working assuming the Servo controller is properly configured Scope latitude is the effective latitude of your scope It is the same as your own latitude if your scope is level but will be a slightly different latitude if the scope is not level in a north south direction This process will calculate your latitude If you want to save this automatically calculated latitude in the Servo Controllers Flash ROM simply press and hold both the top right RTN key and the top left ESC key simultaneously for more than 10 seconds Note The latitude calculation was wrong on the SiTech Controller Firmware versions 1 5 and earlier If you have version 1 5 or earlier you will have to enter the latitude using the ServoConfig software or upgrade to version 1 6 or later Choice 3 If your scope latitude is known and it is programmed in the Sidereal Technology Dual Servo Controller simply point the scope at the Celestial pole now press and hold t
59. suffer Changing the mount error terms used The checkboxes on the left side of the PointXP screen will enable or disable various mount error terms You can see the result after enable or disabling a particular item by watching the stars in the pointXP error display and looking at the RMS or peak errors Some of the values will be 00 00 00 even if the box is checked This is because PointXP will not do some of the Mount Error terms until enough stars are loaded to make sense of the particular terms The Model Sensitivity number This number is not based on how accurate your telescope is but instead is an indicator of what PointXP has to work with This should be as low as possible hopefully less than 25 If higher than 100 please keep adding Cal Stars until the number is acceptable to you Be sure you ve 76 of 236 included azimuths RA s through all 360 deg s if possible and altitude Declinations from horizon to zenith from lowest declination to pole if equatorial This will give PointXP enough information to work with Viewing Editing your Cal Stars You can click on Display Cal Stars button and you will see a window that has all the calibration points in it You can remove any star from being used in the PointXP Engine by clicking on the word USED It will change to Not Used You can change it back to being used by clicking on the Not Used Pay special attention to the column labeled Error This is the devi
60. supports almost every ASCOM Version 2 1 function and later Using SiTechEXE also provides extensive built in capability providing periodic error correction sky mapping for extremely accurate pointing PointXP scripting and automatic sky mapping using a CCD or DSLR camera CalPointsXP and PlateSolveXP This method gives the most functionality to your SiTech system Use Mel Bartels SCOPE II Windows Mac UNIX software Java Based observatory quality incredibly accurate GOTO and Tracking http www bbastrodesigns com BBAstroDesigns html Mel has spent many hours providing almost every possible feature in SCOPE IL If you want better than 1 arc minute pointing sky to sky or want to do serious photography Mels SCOPE II is an excellent tool The ASCOM Driver is not used Use Mel Bartels Windows software ScopeIII We are excited about this and wait with anticipation what Mel will have put together in this new software We understand Mel will have this version available in late 2009 Use a Palm Pilot or Windows Mobile based PDA a Blue Tooth Serial module and Astromist Software by Cyrille Thieullet We are also excited about this option as Cyrille has created a brilliant piece of software with many features Please check out http www astromist com for more details Also soon to come is control using JavaME which can be found on many Cell phones Finally a servo telescope control that is affordable You can purchase a bare bones servo controlle
61. the GOTO and does not try to tweak the Dec position Be sure to save the results in a PXP file from within PointXP so you can reuse it Click on Write Config to save the terms to the Sitech cfg file so they are automatically re loaded the next time you start Sitechexe and also click on Save CalStar File to save the star data to be able to reconstruct the terms if you need to in the future PointXP can be set up using PinPoint in a very similar way Contact Dan directly for the details 89 of 236 5 2 FEATURES TAB 5 2 1 Polar Align This button will assist you in performing a Polar Alignment for an equatorial mount Some users will find this easier than doing a drift align and some will find using the PXP capability better Every time you add your second star or if you have a GEM perform a meridian flip then your polar alignment altitude and azimuth deviations are captured and displayed Selecting your first two stars for this Find two stars near the celestial equator prefer both below or both above the equator These should be close to one another in Declination but as far apart as practical in Right Ascension without going below say about 25 or 30 deg s in elevation Very carefully perform a Load Init Point on these two stars It s absolutely crucial to either use a camera or a crosshair eyepiece It s always best to let the R A catch up so you know it s pushing the drive and always come from the declinati
62. the cursor but not before And as the cursor gets to the edge of the screen the screen will be re drawn To perform an initialization on a target slew the scope to center the target in the eyepiece or camera image a cross hair on your CCD image or illuminated reticle eyepience is handy for this and improves your results but is not mandatory Then click on the target in ECU that the scope is centered on You will get an information screen on that target as shown below 161 of 236 ernet Windg plorer Media H Hd Tycho 2 Star TYC 3105 02070 1 RA 18 36 56 19 18 6156070 hours Dec 38 46 58 8 38 782992 degrees Magnitude 0 1 Extinction 0 11 Azimuth 062 33 Rises at 11 46am Altitude 40 22 Transits at 07 35pm Air Mass 1 5 Sets at 03 27am Other Names HIP91262 HD172167 aj Tycho Magnitude 0 09 Parallax 0 12893 0 00055 Implied Distance 25 3 ly 0 1 Proper Motion RA 0 2010 Dec 0 2875 Galactic Longitude 67 45 Ls Center Scope Sync Scope Copy Center Object Place Target Notes Web Search Precess 2009 09 26 20 35 RA 18 36 00 0 Dec 3900 00 Azim 062 18 Alt 40 3 fo How Many Lal Star rit FightAse 183775 19 03 13 InitHourAnale piys 99 90 00 i Irit Declination 38 47 30 a0 00 00 Scope Latitude Peak 00 00 00 Init Azimuth 2855227 95 07 59 Scope Longitude Just Load Szar No Ter
63. too high already and there s oscillation On others you can get away with taking it up to 2 or 3 If it doesn t oscillate on the end of a slew then you should be able to increase it The other thing you can do is add some Slew Settling time so it won t report that it s done slewing until the slew settling time has elapsed PointXP Troubleshooting Problem I saved the cal star file and parked the scope I have 17 stars in that file Is it now possible to add more stars to that file in an additional session Solution No you have to add all the stars at once Problem Question Now that I ve checked those two boxes nutation aberration will I get better performance or will I need to re do the PointXP run Would these two factors be significant enough to give me the slightly offset slews that I was seeing of about 3 arc minutes Solution Cartes Du Ceil does NOT send nutated abberated coordinates You will do better but you will have to start over on a new PXP run One trick you can use is to Oh yea if you use Cartes Du Ciel then you must certainly turn Nutation and Aberration on in the SiTech config Problem Is it possible to use only 1 2 the sky with PointXP Say if someone has their northern sky blocked by a large group of trees etc Or just using the eastern half As to selection should one move from one star to the next in some defined order or randomly move about the sky until it has been covered swinging back and forth
64. up to the same price except for shipping and handling 10 3 TECHNICAL SUPPORT If you are using Scopell and having issues you need to contact Mel Bartels for Technical 131 of 236 Support Mel is extremely patient and will work with you until you are up and working if necessary he will provide telephone support If you are having problems with the controller radio handpad or the ASCOM driver or are having problems with the Argo Navis controlling your telescope Sidereal Technology will help you We are available by email anytime grayarea sidereal technology com You will receive a response generally within 8 10 hours You can also call Dan Gray anytime before 10 00 PM Pacific Time His phone number is 503 887 3701 132 of 236 10 4 BASIC RF HAND PAD OPERATIONS 10 4 1 Mounting the Receiver The receiver should be mounted where there are no obscuring metal parts for best reception If you want to see the LED s for status mount the unit close to where it will be visible from the eyepiece side of your telescope You can use Velcro to mount the unit 10 4 2 Connecting the Receiver The Receiver connector labeled Handpad Connector should be connected to the SiTech Controller port labeled Handpad Use a flat 6 conductor cable with two 6 position modular jacks Pin 1 should be connected to pin 1 on each connector This cable is normally supplied with the unit If connecting to a Mel Bartels Stepper system the
65. with this checked That assures no wrapping up of wires being fed through a hollow azimuth axle for instance The downside is if you want to slew from NE to NW the mount will have to slew all the way around through the south to get there For a fork mount you have the same behavior since it is really just an alt az mount with the Az axis aimed at the NCP For All mounts you have the ability to set a minimum altitude dd mm ss that the telescope will not be moved below This is very useful for alt az mounts that cannot be lowered all the way down to the horizon or for any mount when you are tracking satellites and the tracking software can end up trying to track below the horizon GAIN Az and RA Gains can also be set The default is set to 1 0 All telescopes are not equal If your telescope oscillates when a goto is finishing then finally comes to a stop put a lower number here If your telescope takes a long time to close in at the end of the slew then try for a higher number To see how well it tracks using different gain values go to the NUMBERS tab and look at the PAxisError and SAxisError Make sure they are as close as possible to 00 00 00 0 before doing a CalStar init by the way if you remember to look here If the value is oscillating around a lot lower it a bit However in Tick Management Mode these numbers do jump around a bit and that is normal 60 of 236 4 11 3 Setup Scope Encoders Tab Setup SiTech ASCOM
66. 1 Used Click on the USED text to disable or re Delete All Delete Selected 2140 enable a point Click on the Star to Select or De Select for zo o j Close deletion a i Common problems Unpark The SiTech driver will automatically load up the pxp file that was in use at the time of your Set 77 of 236 Park command If you ve moved your mount or changed something in your mount you may want to do another calibration run and another set park Garbage in MegaGarbage out PointXP needs truth as we are all searching for If you feed PXP garbage it can sometimes make things even worse Sources of garbage 1 Roller Drive Slippage using mount encoders can help with this one 2 Noise on motor or telescope encoder lines using pull up resistors on early style controllers can fix this The later style controllers have the pull ups built in 3 Adding the wrong Cal Star 4 Large Periodic Error or non periodic error use the built in PEC routine or use high resolution mount encoders in Tick Management Mode 5 Star Catalog Coordinate Errors 6 Backlash set up backlash correction using the tool in ServoConfig or use high resolution encoders in Tick Management mode 7 Wrong use of Nutation and Aberration Story behind PointXP by Dan Gray I m a pretty good programmer however I m not a mathematician so when it goes beyond basic trig or algebra I rely on the internet or some of my friends who are bett
67. 184K _deNieService ava SYSTEM _ an an Cl Show processes from all users End Process w Processes 67 CPU Usage 8 Commit Charge 610M 4959M MICFOSOFC Laiculator 164 of 236 TheSky TheSky versions 5 and 6 can be used to indicate where the SiTech telescope is pointed and also control the SiTech GoTo mount TheSky has direct control features for many popular mounts but not the SiTech In order to use TheSky with SiTech you have to add a file to your computer and set up TheSky to work with the new file Both versions of TheSky 5 amp 6 use the same procedure We haven t verified if these procedures will work with the new TheSkyX The following procedures work with ASCOM 4 and ASCOM 5 You should have ASCOM on your computer before you set up TheSky with SiTech TheSky ASCOM Telescope TeleAPID Plug In There is a Plug in on the ASCOM Website at http www ascom standards org Downloads Plugins htm that allows Software Bisque s TheSky 5 6 Astronomy Software to control telescopes via ASCOM telescope drivers via TheSky s TeleAPI feature For more information see Working with TheSky section 2 at the above link It has a very good explanation of what is going on The Plug in download is a zip file with a read me document describing installation and usage After downloading the Plug in read the installation instructions They are paraphrased here 1 Rename the file C Program Files Common Files System Te
68. 25 102 54 Used INo Coordinat 07 27 27 21 55 42 01 10 40 18 144 15 228 00 10 Used INo Coordinat 07 27 27 21 58 26 01 53 237 34 150 17 siS 01 47 Used No Coordinat 07 27 27 Z1 59 51 01 55 2 1 18 159 06 1 14 01 25 Used No Coordinat 07 27 27 22 04 29 01 32 723 43 164 32 LO 01 18 Used No Coordinat 07 27 27 22 07 08 01 45 212 211 170 42 220 02 30 Used No Coordinat 07 27 27 22 08 08 02 02 248 35 177 09 224 00 33 Used Coordinat 07 27 27 22 10 01 02 19 2 5 48 182 56 oe 2 02 48 Used Coordinat 07 27 27 2Z 11 56 01 S51 17 03 190 14 iea 01 35 Used Coordinat 07 27 27 2Z2 14 10 01 24 207 47 188 02 323 04 09 Used Coordinat 07 27 27 22 17 10 01 09 07 39 190 04 200 01 33 Used Coordinat 07 27 27 22 19 20 00 44 55 501197 57 46 03 18 Used Coordinat 07 27727 22 22 38 00 59 18 08 209 21 249 03 36 Used Coordinat 07 27 27 22 24 53 02 00 701 40 200 55 203 05 27 Used Coordinat 07 27 27 22 27 00 02 45 231 43 198 25 218 06 01 Not Used Coordinat 07 27 27 22 31 35 02 04 222 32 137 34 288 01 41 Used Coordinat 07 27 27 22 43 10 23 04 08 05 27 47 s22 00 52 Used Coordinat 07 27 27 22 47 19 22 S8 234 01 29 56 16 01 56 Used Coordinat 07 27 27 22 49 14 21 47 704 44 16 20 223 02 54 Used Coordinat 07 27 27 22 52 38 20 21 k i iM al or fe 47 100 54 Used Coordinat 07 27 27 22 54 46 20 48 1 27 23 09 41 Sate 00 51 Used Coordinat 07 27 27 22 56 02 20 48 2 9 18 05 14 7 54 40 00 3
69. 9 Focuser Field Rotate Motors Automatic 4 2 1 STOP Stopped Tracking Startup Tracking Just below the Park buttons are two buttons one labeled STOP and the other will change its label depending on what is going on with the default for the second button being Stopped One of the options in the Configuration window for Equatorial mounts is to have the system start blind tracking when SitechEXE is first started In this case the Stopped button label will read Startup Tracking To get the system tracking assuming the start tracking when SitechEXE starts option is not selected in the config window you must tell the mount where it is aimed This is referred to as initializing the mount After the first init is performed the mount will automatically start tracking How to perform Inits will be covered in the section on the GoTo Sync Tab To stop tracking once it has been started simply click on the STOP button The right hand button will change to Stopped To restart tracking click on the Stopped button to change it 36 of 236 back to Tracking 4 2 2 Message Window Just below the STOP Stopped buttons is a message window that will cycle through information one message at a time on what the system is doing If there is more than one message to display it will rotate through all valid messages till all are displayed and then keep repeating the sequence Here are the following messages al
70. ALT key and press the SPD button If this is not done the transmitter will power down by itself to save batteries after about 15 minutes 10 5 DragNTrack AND SlewNTrack HandPad OPS ALT AZ SCOPES ONLY 10 5 1 Tracking Control The top right key will stop and start the tracking flashlight must be off 10 5 2 Initializing To initialize if your scope latitude is not programmed into the Servo Controller point the telescope at the scope zenith then press and hold the top right key for more than 5 seconds when the LED on the controller flashes fast you may let up Now point the scope at the Celestial Pole Now press and hold the Top Left key for more than 5 seconds when the LED on the controller flashes fast you may let up Your scope is now initialized and the DragNTrack or SlewNTrack will be working assuming the Servo controller is properly configured Scope latitude is the effective latitude of your scope It is the same as your own latitude if your scope is level but will be a slightly different latitude if the scope is not level in a north south direction 136 of 236 If you want to save this automatically calculated latitude in the Servo Controllers Flash ROM simply press and hold both the top right RTN key and the top left ESC key simultaneously for more than 10 seconds Note The latitude calculation was wrong on the SiTech Controller Firmware versions 1 5 and earlier If you have version 1 5 or earlier y
71. COM Driver VO 54L Telescope Info Mount Info Scope Encoders Miscellaneous Ascom and Troubleshooting Focuser Rotator Potentiometers Alt z C Equatorial German Equatorial Parameters Altitude Limit 00 00 00 German Equ V GEM Auto Flip GoTo GEM Auto Flip Track f Az Ra Gain Alt Dec f Don t Reverse Guide Mode when Looking East 15 00 00 Meridian Overlap Degrees Freeze Declination Equatorial only E i ey on Start Equatorial OK Sines Help Azim RA Nowrap l You can have 3 types of mounts Alt Az Equatorial or GEM please select the proper type If you have an equatorial or GEM mount you have the following additional selections that are in the area labeled German Equatorial Parameters GEM AutoFlip on GOTO If selected if you try a GoTo to an object on the other side of the meridian the telescope will perform an automatic GEM flip GEM AutoFlip on Track If selected if the tracking comes up to the meridian limit then a GOTO to the same object on the west side of the meridian will be performed and a meridian flip to get there will be executed Don t reverse Guide Mode when Looking East If not checked the autoguider guiding direction which normally needs to be reversed after a flip will get reversed in SitechEXE so the 59 of 236 autoguider does not have to be reversed Since Sitechexe does equal area panning and guiding do not use the option in your autoguider progr
72. Click on the Errors Toggle button to see areas of the sky you ve missed e Click on a blank area and perform a Goto to this area 5 Click on Show CalStars and edit out any stars with large errors click on line to change used to not used Click on Save CalStar file to save your work Click on Write Config to save terms to Sitech cfg file will be saved there anyway when Sitechexe is closed eon 201 of 236 Scripted PointXP Operations For more details reference section 5 1 5 1 Initialize telescope OK to have a planetarium program connected to Sitechexe to do the initializations e Click on Clear all terms and Cal stars in the PointXP window e Perform an Offset Init to start tracking e Manually perform at least one Cal Star Init 2 or 3 separated in alt Dec and az RA are better to provide pointing accuracy to better than your cameras FOV 2 of them should be separated in RA Az as much as possible and the 3rd separated as much as possible in Dec Alt Important to not perform any Offset Inits after these first 2 3 CalStar Inits before performing the Scripted PxP Run 2 Call up camera control s w and connect to camera if not previously done e Verify good focus Make sure Focus mode is exited and not running when script is started e For Nebulosity run the ListenSitech neb script o Click on Edit Run Script and select ListenSitech neb file from the My Documents Folder o Verify the camera c
73. Delete COM a Create COM Hide 9 13 2009 2 44 02 PM Keep connection message sent 9 13 2009 2 44 49 PM Keep connection message sent 9 13 2009 2 45 37 PM Keep connection message sent EO Final Networking products group www HW group com IV Start with Hi Precision Protocol aay a ee Embedded Ethernet Devices 142 of 236 11 1 INSTALLATION 1 First download and install HW_VSP http www hw group com products hw_vsp hw_vsp2_en html Make sure you download and install their version 2 5 10 It may not be the latest but the commandline startup options are gone in later versions 2 Now unzip and copy LXToSiTech exe to the SiTech folder C Program Files Common Files ASCOM Telescope SiTech 3 Now best to start up SiTechExe and get it initialized If you don t LXToSiTech will start SiTechExe for you however you will still have to get it initialized properly 4 Be sure that no copies of HW_VSP are running If it is already running it may well have wrong parameters The correct parameters are sent to the program using the command line when it is started by LXToSitech 5 Now run LXToSiTech exe This will automatically start HX_VSP 6 Take a look at the information window in HX_VSP It should have created serial port Comm5 which is the default You may be using Comm5S for something else If this is the case it will fail However don t be alarmed 6A Close both LXToSiTech and HX_VSP 6B Edit the
74. Driver VO 54L Telescope Info Mount Info Scope Encoders Miscellaneous Ascom and Troubleshooting Focuser Rotator Potentiometers Azimuth RA Altitude Dec Ignore C Ignore Precise Mode C Precise Mode Polite Mode C Polite Mode et Cascade Mat Tick Mnamnt Tick Mngmnt Gurley Interpolation Correction 320K TPR M f Gurley Interpolation Correction 500K TPR I E Supervisory Threshold 00 00 12 00 00 71 2 Supervisory Threshold Drag Mode OK Cancel Help There are two main areas on this tab one for the RA Az axis and the other for the Dec Altitude axis There are 5 ways to use mount encoders 1 Ignore If selected then the telescope position will exclusively come from the motor locations You can override this in the Controller Stuff under the Features tab You can update the encoders to the value of the motors or vice versa in this way 2 Precise Mode If selected then as soon as there is a dis agreement between the motor location and the encoder location that exceeds the Supervisory Threshold then the motor location is updated to the encoder location Please set up the Supervisory Threshold to a value that is GREATER than the resolution of your telescope encoders Lets say you have an 8192 resolution encoder on your telescope This is about 3 arc minutes so you might want to set up your Supervisory threshold to be 4 arc minutes 3 Polite Mode If you are doing photography you may want to use the Polit
75. EC Curve in the Controller is a flat line by clicking on the Read Cntrler PEC Table into Cntrler Buffer button in the left column Make sure Show Latest from Controller is checked on the far right and verify the green line that is displayed is flat 3 Sync the worm period e For autopecsync detector go to the pec page in sitech exe and turn it on e For manual pec sync line up a mark on the worm and an index point Press top left handpad button when lined up No need to even stop tracking 4 In PemPro Verify connected to the camera and also the mount and PemPro sync d e Make sure the worm period set up correctly in PemPro e Always run the PemPro calibration wizard to verify the camera pixel resolution and rotation angle e Click on sync PemPro will query SiTech exe for the phase of the worm and you will see the PemPro display update accordingly 5 Record several worm periods in PemPro by clicking the START button in PemPro and process the data according to the help files in PemPro and save the PEC curve 6 In Sitech verify there are no Collective Items in the Collective in case you were messing with PEC earlier In the middle column it should say You have 0 in Collective If there is something in the Collective click on the Clear Collective button in the middle column Just to make sure click on the Show 5 Collective Items on the right The Pink line should be flat 7 In SiTech exe s PEC graph
76. ETUP Manual for the cable diagram If you don t have telescope encoders not to worry because you can select the SlewNTrack mode of operation and now the encoder information will come from the servo motors not the telescope encoders Also if you do use telescope encoders they will be powered from the Servo Controller power thus the 23 of 236 Argo Navis batteries will last much longer 2 4 1 Setting up the Argo Navis Several items need to be set up on the Argo Navis before operation Go to the Setup menu then select the Serial Port then Serial 1 Make the Startup command be SiTech Also set the baud rate to 19200 Go to Setup and find the Altitude and Azimuth encoder resolutions Change these to 18000 Set up other parameters as required for your telescope such as location etc Be sure to read the Argo Navis manual Note the encoder resolution parameters in the Argo Navis do need to be set for 18000 regardless of the actual encoder resolution This is extremely important The Servo Controller always scales the encoder ticks for 18000 even if you have other resolution encoders 2 4 2 Setting Up the SiTech Controller for Argo Navis Now you need to set up some things in the Sidereal Technology Servo Controller Using the ServoConfig software click on the Edit Parameters button then on the Misc and Action tab You must have version 1 0 or later of the ServoConfig software Check the box labeled Use
77. ING THE FREE SiTtechEXE PROGRAM PointXP is a mount error modeling routine for corrections of pointing errors and is incorporated into the SiTech exe software Using a PC you can align on stars across the sky once and then have extremely high pointing accuracy with corrections for most mount polar alignment and telescope errors on subsequent nights Pointing accuracies of several arc seconds have been achieved PlateSolveXP is a stand alone program that determines the center of field of view of a camera and passes those coordinates to PointXP for exceptional pointing capability with the mount It graphically shows the extracted stars the catalog stars and the matched stars It also displays the J2000 coordinates of the cursor a useful feature for astronomical research and object identification CalPoints is a utility that works with SiTechEXE to help automate the mapping of the sky using PlateSolve and PointXP to generate a sky database of mount corrections for extremely accurate mount pointing Built in periodic error correction and support for PemPro operation is available in SiTech exe with a PC connected You can record periodic error directly in SiTech or use PemPro to determine the correction pattern The controller will then apply the corrections automatically This feature requires either manually synchronizing the worm gear rotation or using an AutoPECSynch sensor on the worm gear Circuits for these sensors are shown in the appe
78. K K EEE EKE E E 28 K K K E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K EEEE E E E 2S K E E K K E 2g 288 K E K K K K K ig K K K K k K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2 K K EEEE E E E E E E E E E E 2g E K E E K K K k 2s K K K K k K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2k K K KEE E KE KE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K KEE E KE E E K K K K K K K K 2g K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2s K K K K 2K K K EEEE E E 28 E K KE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K 229 of 236 Controller Firmware Version History Version 1 0 sent out on 7 1 2000 or so then found altitude scope encoder bug 31 1 fixed altitude scope encoder bug now when you send config to controller it not only writes it but reads it into ram improved motor encoder routines made 50 clocks down to average 25 clocks No new serial numbers can be written turning 1 s into zeros s adjusted the skippid feature less proportional and switch at higher speed disable interrupts for scope encoders if in slew and track mode Added XS and YS display Added XR and YR display RAMP OR ACCELERATION Added XEL a
79. K K K K K K K K K K K K K K K K 2k K K K K 2 K K 0 21 Same as 0 20 except the created bug about goto s not working was fixed KEKE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 0 20 Fixed longitude display in setup Fixed Get String window not on top added checking for return etc works better Added GuideMode and CanSetGuideMode property for John M Added east west correct for park unpark so an unpark will initialize both east and west Made Meridian flip move farther past the pole in declination before moving on Fixed the Init pointer to display properly and work properly after deleting inits Put Try Catches in all timers Found and fixed bug writing new values to configuration if a string was in a string didn t work right Added timeout capability to YesNo Found problem with conflic between autoguiding and r a dec setpoint control 226 of 236 PRS FAS 2S 2g 2g 2g E E E E E K E K K K 2g K K FAS K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K FK K K 0 19 Improved reporting inits made startup autotrack option tested it Added ticks per rev to the configuration Made message if changed EEEE E E E E E E E E E E 2g E K E K K K K K 2s K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K 0 18 Made the z3 calculate on 3rd and following star Altitu
80. Log ASCOM Log Debug Stuff Log Gurley Interpolation There are two options available for communicating with the Windows Operating System Above Normal and High You should use Priority High unless you are troubleshooting with Dan The Gurley Interpolation Periodic Error IPE correction routine can end up with un inverted data The result is the approximate 4 arcsec IPE can be made worse rather than being damped out If that happens check Invert Gurley Interpolation If you are using the program SatTracker to control SitechEXE to track satellites and you are using an Alt Az mount you will need to check the box ASCOM AxisRates to R A and Dec 68 of 236 since Sitech needs to be using RA Dec setpoints instead of the axis rate commands SatTracker sends to an Alt Az mount Otherwise you can leave this un checked Slew Settling time is the time after a slew is completed for the mount to be assured of having resumed normal tracking This is important when SitechEXE is communicating with other programs especially camera control programs and the scripted PXP routine since SitechEXE will wait this long to tell those programs the slew has officially ended and its ok to take images There are two blocks for changing the configuration of Pulse Guiding Autoguiders can send rate commands or a pulse guide commands A rate command adds or subtracts a rate to the mount s movement However it also needs a second rate c
81. NNOYD OL LOANNOO e UIDE MODE TORECEVING Gran MODE LYOd GVdGNVH YadddalS YO OAYAS OL ASSWIHOWW 18Y7 1431 z HINOSINMOG 3dd31SNO 110A S ONNOH HLHONAN S SLIOAS 9 Wa SAS OATES JO 3194 Joguine Wa sks Jeddals 10 9109y 19d WNP 194 of 236 Appendix H Cue Cards A Cue Card is a shorthand version of a checklist The idea is to have a very simplified memory jogger for use at the telescope at 3am when we all get a bit fuzzy and do not want to try to look something up in one of the manuals The Cue Cards listed in this appendix are examples of what I have found useful to me You may find information on them you do not need or want to add your own Use them in the spirit they are provided which is to illustrate how to capture relevant information about the Sitech system in a shorthand format that meets what you want to have at your finger tips Enjoy Normal Startup Assumption is that PXP terms have been calculated and saved in a previous session and controller is not configured to be in Equatorial Mode if the mount is equatorial Mount Was Moved since Last Session Start Sitech exe Start Planetarium Program and Connect to Telescope Perform an Offset Init to get tracking started Update Offsets but do not change PXP Terms Perform 2 5 Just Load Star no terms Inits Click on Calc only Offsets Align Mount was NOT moved since Last Session Start Sitech exe Start Planetarium Program and Con
82. NTrack or SlewNTrack modes will be disabled To check that the communication is working properly go to the Encoder menu item in the Argo Navis and make sure the angles change with telescope movement 24 of 236 You are now ready to initialize the Argo Navis Please follow instructions in the Argo Navis manual for initializing the Argo Navis Now the telescope should start tracking properly when the Argo Navis is initialized For GOTO s simply select an object using the Argo Navis then after confirming that the object is above the horizon press the handpad ESC and RTN buttons at the same time Top Left and Top Right buttons The scope should now move to the object To stop a slew press any direction key on the handpad To restart the slew press the ESC and RTN Top Left and Top Right buttons again To stop tracking press the top right key To start tracking again press it again When the tracking is stopped the LED s will blink off briefly every few seconds version 1 6 of firmware and later Some useful info about the Argo Navis mode The SiTech controller does two slews each time you slew to another object The first slew gets it in the area then the final slew takes it to the exact position The reason it does this is because on long slews the earth will turn and thus the location will have changed after the 1 long slew 2 5 USE WITH SKY COMMANDER It is possible to connect the SiTech controller t
83. Ok to explain what it does or really doesn t do There is an internal RA Dec setpoint in the ascom driver it is RA Dec even on an alt az scope When you command the telescope to move to a different part of the sky all you do is change this setpoint Once the telescope is at this setpoint it keeps comparing the current position of the telescope to the RA Dec setpoint and continually makes correction This takes refraction into account as well and if you have multiple stars it will take this into account as well correcting for any polar mis alignment When you click on the DragMode the only time the RA Dec setpoint is used is just after a command to move to another part of the sky Then only blind tracking rates are sent Now it will not keep it on a given ra dec but if the rates don t keep it perfectly tracking then drift will occur that will not be corrected Advantages of Drag Mode You can drag your telescope around the sky and it will begin tracking at the rates of the new location It will not try to return to the latest setpoint If you select ignore encoders then you won t be able to drag your telescope however the same principle applies there is no RA Dec setpoints it still is blind tracking Disadvantages of Drag Mode You will not be able to do any RA Dec offset tracking The tracking will not be as accurate because the scope isn t tracking to a particular point in the sky but blind tracking rates are sent to t
84. Park UnPrk SetPrk STOP sutupTia Ra 16 54 14 6 H Scp Hr ng 12 00 45 Dec 00 06 30 Focuser Field Rotate Motors Automatic The Scope Tab is the default panel that comes up We will refer to it as the main screen 4 3 2 Virtual Handpad The upper section is a virtual handpad that you can left click on to move the scope Holding down the left mouse button on one of the directions is the same as holding down the arrow buttons on the handpad Release and the virtual handpad arrow button is released The gt buttons are the slower PAN speed and the gt gt buttons are the faster SLEW speed Click in the middle and the speed for the buttons is the very slow GUIDE speed Set the speeds and save in the controller using ServoConfig exe The mode the controller is in is shown the window below the words Controller Mode The Button with the H is to call up the help file to remind you of some of this information The button labeled DBG is to start the De bugging logging This has been there during development and will probably get removed in a future release 39 of 236 4 3 3 PointXP Button ADVANCED FEATURE The large button below the virtual handpad named PointXP 0 Star s Loaded shows how many Calibration Stars have been loaded and clicking on it serves to bring up the PointXP window which is the mount calibration modeling program within SitechEXE The more accurately the mount is
85. Planetarium Program Connected Use Handpad to center telescope on target Click on Target in the Planetarium Program Select Sync from within Planetarium program For GEM VERIFY Looking East or Looking West Verify type of init when Init Window opens default is Offset Stop timer with left button if desired If timer was stopped click on type of init then on OK Drift Align Prior to doing a drift alignment e Mount should be initialized with one Offset init to allow tracking e For Equatorial mounts FREEZE Declination o Config Screen Mount Info Tab o Bottom left corner area check mark in Freeze Declination box Perform Drift Align only watch Dec motion ignore RA drift e RA Axis Altitude Center on star on celestial equator near East Horizon e RA axis Azimuth Center on star on celestial equator near Meridian After Drift Alignment completed e UN Check the box to stop the Freeze Declination option GOTO Mount must be initialized first e Can be initialized via Initialization Cue Card techniques e Can be Initialized by doing an Unpark IF it has been properly Parked 196 of 236 GOTO operations same as Inits except click on GOTO rather than Sync SetPark Park and Unpark For more info reference section 4 3 4 Mount MUST be properly Initialized first To setup PARK for the first time or change Park Position previously saved Either GOTO or Manually move via handpad or Drag n Track mode to desired Park
86. PointXP Platesolve script it is highlighted in red above This highlighted section is explained in the previous section addressing Scripted PlatesolveXP Operations oe Here s a list of the commands and what they do Slew hh mm ss dd mm ss slews to right ascension and declination at a rate at slew speed Slew M31 slews to right ascension and declination of M31 at a rate at slew speed Slew NGC4565 slews to right ascension and declination of NGC4565 at a rate at slew speed Pan hh mm ss dd mm ss dps moves to right ascension and declination at a rate in degs per sec Pan with name of object same as slew Wait secs tracks while waiting Pause waits for topright key will track while paused While label for loop to go to Sound filename plays a wav file with the name substitute the sound file s name for filename Following are commands used for the relative panning mode These commands won t be useful if you aren t using Pan Relative commands Anchor memorizes the current co ordinates that are used in the PanRel command at time of script running not time of adding command SlewToAnchor slews to the anchor RA Dec PanRel hh mm ss dd mm ss dps like pan but instead of absolute co ordinates they are relative 91 of 236 PanToAnchor dps The pan speed dps mentioned above is Deg s per Second Typical Pan Speeds for visual observing would be about 0 03 to 0 2 After you put out the first DPS then y
87. SIDEREAL TECHNOLOGY Operations Manual Copyright Sidereal Technology 2004 2005 2006 2009 Draft Version 1 1 Revised October 20 2009 http www siderealtechnology com 1 of 236 Revision History for the OPERATIONS Manual 7 THE BIG PICTURE READ THIS FIRST 8 1 FEATURES 9 1 1 BASIC BUILT IN STANDALONE CONTROLLER FEATURES 10 1 2 ADDITIONAL FEATURES AVAILABLE USING THE FREE SiTtechEXE PROGRAM 12 1 3 COMPARISON BETWEEN STEPPER SYSTEM AND SERVO SYSTEM 13 1 4 SAFETY 14 1 5 SOFTWARE VERSIONS 14 2 OPERATION WITHOUT A PC 15 2 1 ALT AZ DRAG AND TRACK MODE 15 2 1 1 Setting Up the Drag and Track Mode 16 2 1 2 Operation of Drag and Track Mode 17 2 1 3 Review of Alt Az Initialization options 18 2 2 ALT AZ SLEW AND TRACK MODE 20 2 3 EQUATORIAL MODE 21 2 3 1 Setting Up the Equatorial Mode 21 2 3 2 Operation of the Equatorial or Tracking Platform Mode 21 2 3 3 Observing the Crab Pulsar 22 2 4 USE WITH AN ARGO NAVIS 23 2 4 1 Setting up the Argo Navis 24 2 4 2 Setting Up the SiTech Controller for Argo Navis 24 2 4 3 Operation of the Argo Navis 24 2 5 USE WITH SKY COMMANDER 25 2 5 1 Set Up SiTech Serial Port 25 2 5 2 Setting up SiTech for Sky Commander 26 2 5 3 Setup Sky Commander for use with SiTech Controller 26 2 5 4 Initial Setup and Testing of Alt Az Sky Commander with SiTech 28 2 5 5 Starting and Using SiTech with Sky Commander for Alt Az Ops 29 2 5 6 Initial Setup and Testing of Equatorial
88. Scope on a Fixed Object 4 10 CONFIG TAB 4 11 SiTechEXE CONFIGURATION SCREENS 4 11 1 Setup Telescope Info tab 4 11 2 Setup Mount Info Tab 4 11 3 Setup Scope Encoders Tab 4 11 4 Setup Miscellaneous Tab 4 11 5 Setup ASCOM amp Troubleshooting Tab 4 11 6 Setup Focuser and Rotator Tab ADVANCED FEATURE 4 11 7 Setup Potentiometers Tab ADVANCED FEATURE 4 12 CONNECTING WITH YOUR PLANETARIUM SOFTWARE 4 13 EQUATORIAL AND GEM INVERT BUTTON SETUP 4 13 1 Northern Hemisphere Setup 4 13 2 Set Up and Operation in Southern Hemisphere 5 ADVANCED FEATURES 5 1 SCOPE TAB 5 1 1 PointXP Mount Modelling 5 1 2 Aligning PointXP Using PlateSolveXP 5 1 3 Scripted PlateSolveXP Operations 5 1 4 Scripted PxP Setup and Configuration 5 1 5 Scripted PxP Operations Procedure 3 of 236 5 1 6 PXP Tips and Tricks and Lessons Learned 5 1 7 Aligning PointXP Using other Plate Solvers 5 2 FEATURES TAB 5 2 1 Polar Align 5 2 2 Run Script 5 2 3 Making Scripts 5 2 4 Using the Handpad to control a Script 5 2 5 Controller Stuff 5 2 6 PEC Control 5 2 7 Simple PEC Recording Session 5 2 8 PEC Playback Session 5 2 9 PEC Complex Recording Session 5 2 10 PEC More Info 5 2 11 Periodic Error Correction with PemPro 5 2 12 Offset Tracking Rates 5 2 13 Clock Calibration 5 2 14 Handpad SlipMode 5 3 Config Tab 5 3 1 Change Config Potentiometers Tab 6 AUTOGUIDING 7 HIGH RESOLUTION MOUNT ENCODERS 7 1 Encoder Mounting Acc
89. Sitech may give you a message saying ECU is already connected and you will be confused because you have not yet connected If this happens you need to bring up the Windoze Task Manager with a Cntl Alt Del three finger trick and click on the Processes Tab as shown below Then scroll down to WOW exe and click on it and then click on End Process Windows will warn you terrible things might happen so humor Windows as I am sure you are already used to doing and click OK WOW exe will close and then close the Task manager and ECU should connect just fine Windows Task Manager Applications Processes Performance Networking Image Name User Name CPU Mem Usage EditPadLite exe cshaw oo 3 908 K rapimgr exe cshaw oo 5 244 K wmipryse exe SYSTEM 00 11 860 K taskmgr exe cshaw oo 5 096 K DotixCfg exe cshaw oo 16 784 K weescomm exe cshaw 00 5 100 K Apoint exe cshaw 00 4 648 K wmipryse exe SYSTEM oo 5 508 K WOWEXEC exe cshaw oo ecuS exe cshaw oo ntvdm exe cshaw oo 1 996 K ApMsgFwd exe cshaw oo 1 920 K SynTPEnh exe cshaw oo 3 240 K ccApp exe cshaw oo 7 960 K iFrmewrk exe cshaw oo 18 548 K ctfmon exe cshaw oo 4 248 K stsystra exe cshaw 00 8 200 K pddm exe cshaw oo 4 016K SiTechExe exe cshaw 00 4 284 K RIMAutoUpdate exe cshaw oo 11 200 K WINWORD EXE cshaw oo 6 264 K wmipryse exe SYSTEM oo 4 888 K TimeLeft exe cshaw oo 11 224 K CemExec exe SYSTEM oo 18 448 K explorer exe cshaw oo 31 364 K WLKEEPER exe SYSTEM oo 15
90. Sky Commander with SiTech 30 2 5 7 Starting and Using SiTech with Sky Commander for Equatorial Ops 30 3 OPERATION WITH A PC 31 3 1 SOFTWARE USED 31 3 2 LOADING THE SOFTWARE 31 3 3 STARTING THE SiTech TELESCOPE DRIVER SiTechEXE 33 3 4 CONFIGURING THE SiTech TELESCOPE DRIVER 33 4 1 BASIC FEATURES 36 4 2 COMMON AREA OF THE SiTechEXE SCREEN 36 4 2 1 STOP Stopped Tracking Startup Tracking 36 4 2 2 Message Window 37 4 2 3 RA SHA Dec windows 38 4 2 4 Focuser and Rotator Control Buttons Advanced Feature 38 4 3 TABBED SECTIONS OF THE SiTechexe WINDOW 39 4 3 1 Scope Tab Main SitechEXE screen 39 4 3 2 Virtual Handpad 39 2 of 236 4 3 3 PointXP Button ADVANCED FEATURE 4 3 4 Park UnPark SetPark 4 4 NUMBERS TAB 4 5 FEATURES TAB 4 5 1 Polar Align ADVANCED FEATURE 4 5 2 Do GEM Flip 4 5 3 Run Script ADVANCED FEATURE 4 5 4 Controller Stuff ADVANCED FEATURE 4 5 5 PEC Control ADVANCED FEATURE 4 5 6 Offset Tracking Rates ADVANCED FEATURE 4 5 7 Colors 4 6 GoTo SYNC TAB 4 6 1 Scroll FileName 4 6 2 Select File Line 4 6 3 Star and Messier buttons 4 6 4 NGC and IC windows 4 6 5 GoTo and Sync Buttons 4 7 INITPOINT WINDOW 4 8 OFFSET INITS VS CAL STAR INITS 4 8 1 Offset Inits 4 8 2 Cal Star inits 4 9 THINGS TO KEEP IN MIND 4 9 1 First Two Stars 4 9 2 GEM Special Instructions 4 9 3 Single Star Init 4 9 4 Watch your Scope Latitude 4 9 5 Know when to use Cal Star Init Points and when to use Offset Inits 4 9 6 Initializinging the
91. Tech Init Window Do a single photo init Add While Add Loop Click here for HELP Cancel Colors The information below addresses how to use the powerful scripting capability in SitechEXE However in the scripting window there is a special section that creates a PointXP Platesolve 44 of 236 script This section will be explained in the section on how to use the PlatesolveXP program What SiTech Scripting is It will smoothly Pan your telescope across the sky in a predetermined pattern playing wav files if desired for your line of people looking through your telescope What it isn t You probably won t use this for doing photography of multiple objects as there are several other better ways to do this one being the free program by John McClusky called Photolyze You can download this software on the SiTechServo Yahoo users group Details on using this capability are in the Advanced Features Section 4 5 4 Controller Stuff ADVANCED FEATURE You can set the Motor Encoders to the value of the Scope Encoders or vice versa using this window You can also have a look at many controller internal parameters and also there is a terminal mode for direct access to the controller ag Controller Stuff Controller Information Window Colors R24 or Focuser Dec Altitude Rotator or Focuserll RA or Azimuth Motor 00 00 00 Dec or Altitude Motor 00 00 00 Set Motor Location to Scope Encoder Location Set Motor Location t
92. The Par Angle Rotator icon Help Colors Track Parallactic Angle Rotator Setup 127 of 236 9 2 EARLY VERSION OF THE SITECH ROTATOR Prior to Dr John McClusky building the Temp Compensated Focuser routine Dan had simple focuser and rotator routines to control servo motors linked to focusers and rotators If you have a version of SitechEXE that is earlier than 56A you will have the earlier version of the focuser and rotator routines The earlier version of the rotator window is shown below FieidRotate adig Field De Rotator 7 Rotator Angle 00 00 00 Paralactc Ang 3260 00 00 ParalacticRae 0 ccw cw Lett Fast Right Lett Slow Right Enable Sow Handpad _Fast LtFid Stopped RtFid Field Jmp Size 1 Move To Ang 0 Rotate to Stop Par Angle Init Rotator to Zero The Par Angle Rotator Hide Window Help Colors l Track Parralactic Anale There are really no basic functional differences in the routines from the user s standpoint The updated version has been slightly re arranged to use fewer buttons and now has a Rotator Setup button to get to a setup screen Since the basic user functions are the same there are not dedicated early and later version descriptions since the look and feel of the later buttons is similar to the later version of the focuser routine 9 2 1 Parking and UnParking the Rotator When you click on SetPark
93. This is done inside the controller Now SiTechExe reads the current motor position the current scope encoder position AND the position of the motor at the last Scope Encoder Tick Using this information SiTech interprets the overall scope position based on how far the motor position has made it into the current scope position tick I hope that makes sense There is more information on this routine in the appendices of this manual I m throwing out an educated guess based on some experience that this will make your scope encoders perform as if your telescope encoders were about 10 times more accurate as their ticks imply A 10 000 tick encoder has a resolution of about 2 arc minutes This is terrible information to feed PointXP But 12 arc seconds is MUCH better So even if you have only 10 000 count encoders and are doing a PointXP run please use tick managment It will increase your accuracy over using simply 10 000 tick encoders tremendously A couple of folks have used the 10 000 tick encoders with tick managment with good results Jim Roe reports a jump once in a while while using this mode If this happens please still use Tick Mangament while taking your PointXP telescope Model you ll have much better results gauranteed Having about 10 times more accuracy than the encoder implies that you can literally Close the Loop and scope position can be determined to a fraction of an arc second with a relatively economical 320 000 tick Gu
94. To ASCOM manual that will help get you started The Main screen in Megastar and the connection menu is shown below In MegaStar you would select the com port created in the com0com application setup per the MegaStar To ASCOM manual when setting up the telescope communications and select the LX200 telescope for the type telescope to connect to in the Megastar connect config window 172 of 236 ef MEMES Sar Fe maa Comm setup mal oe mema am aE olalla else amal 90 5 D200 z re mma eama Gt 4a 44 4 m gt p gt foe TTBS TES TEE TIE NUp O7h 14m 47 95 1 0 days a Com Port E Seeded BeudRate 9600 C 2400 C 4900 3600 14400 Dist CMa Urano 319 Alt 66 4 Az 94 5 DataBis 8 Ready Stop Bits C Ant tot Iptions for L Zh 30m d 200 interface 7h 00m 6h 30m iV Lock Onto Telescope When the telescope field marker gets near the edge of the field the display will automatically re center on the marker position Set the distance from the edge of the field as a percentage of field size for triggering a refresh Co gs 10 C15 Ca 08 V Show Field Marker Diameter 60 0 Pixels Arc minutes Use Eyepeice Field Polling Interval ms f 100 200 300 400 500 600 Local Syne Radius 5 0 degrees Cancel 173 of 236 Appendix C Database File formats The database files
95. VERY sure if you do a drift alignment that you check the Freeze Declination during the drift alignment process then be equally sure you Uncheck it after you are done and BEFORE you do your PXP run Also be sure you did a 86 of 236 clear stars and terms BEFORE you do the drift alignment e Use the shortest image integration time that still gets you a solveable image when you do the scripted run e I HIGHLY recommend doing three CalStars BEFORE the scripted run Make sure you do a clear stars and terms BEFORE doing these 3 The first two must be separated as much as possible in RA or Azimuth and for a GEM need to be on the same side of the meridian If you have an equatorial mount non GEM ok to have on either side of the meridian but do not make them the same distance on each side of the meridian Do not choose one that is lower than about 20 deg due to refraction also be sure that refraction is turned ON as well as all the other corrections unless you are using a program that cooks the corrections itself The third needs to be as separated as much as possible in Dec or Altitude also on the same side of the meridian if you are using a GEM Try to have this 3rd star low and in the south about 10 deg from the meridian if possible fora GEM The reason is when you go to the scripted PXP Operations which is your next step for a GEM it will start in the SE if the mount is on the east side and SW if the mount is on the W side
96. a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user s authority to operate this equipment C Tick Manufacturers Name Sidereal Technology Manufacturers Address 6040 N Cutter Circle 302 Portland OR 97217 USA Australia Representative Name Wildcard Innovations ACA Suppliers Code N11511 Declares that the products Dual Servo Telescope Controller Model DSTC 1 Handpad Transmitter Model HT1 140 of 236 and Handpad Receiver Model HR 1 conforms to the following standards EMC AS NZS 3548 Class B Complies AS NZS 61000 4 3 Complies Criterion A These units are not for mains connections Industry Canada United Sates Company number 5942A Canadian Representative Nova Astronomics Canadian Representative Company number 5930A 141 of 236 11 LX200 to SiTechExe INTERFACE LXToSiTech exe is a stand alone program so works with any version of SiTechexe after 0 47 It is intended to help folks that use MegaStar or other software that has an LX200 interface but not an ASCOM interface It has been tested with TheSky Earth Centered Universe and Satellite Tracker LXtoSitech automatically calls up and configures a second program called HW_VSP freeware to create a virtual serial port for the non ASCOM program to
97. ability of the system Using the Argo Navis from Wildcard Innovations for complete and accurate Goto and Tracking of your telescope This is a really cool way to go if you don t want the perceived hassle of using a PC at the telescope Using the SiTech unit along with the Argo Navis has several advantages over other systems which use the Argo Navis If optional telescope encoders are 9 of 236 used they are connected to the SiTech unit instead of the Argo Navis the Argo Navis encoder port is un used and the serial port of the SiTech unit is connected to the Argo Navis serial port Some of the advantages are that the encoders draw power from the more powerful Servo Controller Batteries so the Argo Navis batteries last much longer and also the fact that the telescope simply doesn t need external encoders to work with the Argo Navis The user has the option of using external encoders or simply use the motor location instead if you have a system that doesn t slip the best of both worlds Use the provided FREE ASCOM driver SitechEXE exe from Sidereal Technology This requires a Laptop or Desktop PC running Windows 98 through Windows XP The advantage of using the ASCOM driver is almost any planetarium program that supports ASCOM will accurately control your Alt Az or Equatorial telescope No special Virtual Serial Port drivers or NULL modem cables to otherwise unused serial ports This ASCOM driver is very powerful and
98. action on the Configuration page in Sitech on the Miscellaneous Tab TheSky Extras One feature of TheSky 5 amp 6 is that when linked to SiTech TheSky reports the RA and DEC as well as the Altitude and Azimuth to a text file The frequency and location of this file can be set in TheSky in the Server Settings window Don Westergren uses this to pass the current mount RA and DEC to his dome control program by having his program periodically read the position file and then keep the dome slot in front of the scope TheSky Funnies When you click on a star or other target in TheSky you will activate an information window that tells what you are looking at size magnitude etc It also tells you the altitude and azimuth of the object If you leave that window up for a length of time the altitude and azimuth data will not be accurate The RA and DEC will be accurate so if you want to slew to the target you can press the green Telescope Icon on the bottom of the Information Window You can also use the Telescope Tab to use other features you enabled like synch on the object When you are finished operating your scope with TheSky you will have to turn off the link it s the red telescope Icon at the top of TheSky If you forget when you try to close TheSky you will get a message that you are still connected 168 of 236 Cartes du Ciel Cartes du Ciel CDC is a freeware Planetarium Program that is also ASCOM compatible The website
99. after m 1 second Multiple Errors rs N 1 F i i i n X i P i i E Telescope Type and General Settings x Telescope Interface Type P ASCOM Controlled Telescope Silech Telescope l ASCOM Controlled Telescope SiTech Telescope Orion CTI amp JMI SGT MAX 2 00 and later JMI SGT MAX before 2 00 JMI NGC MAX NGC Sky Vector Celestron Ady Astro Master Sky Enginneering Sky Commander Losmandy DSC Meade Magellan Meade Magellan Il Astro Physics GTO Mount Starmaster Sky Tracker Losmandy Gemini System Levels 1 to 3 Now you can click OK in the telescope Type and General Settings window and allow it and the original menu to close Start SitechExe NOTE you do not HAVE to start SitechExe since the next activity will have ECU call it up and start it if it is not running but that can sometimes be a slow process so its quicker to already have SitechExe already running 160 of 236 Now either click on the little Telescope ICON in the command line or click on the word Telescope again and in the menu click on Enable Telescope Interface A small window will briefly appear reporting the progress of ECU connecting to Sitech If it connects OK the screen will then disappear If there is a problem the problem is reported on this screen and you can click on OK to acknowledge it OK did not capture in this screen grab ECU Status BS Connecting to focuser FocusSim Focuser Successfull
100. ailable you can create a virtual serial port using a freeware program called HW_VSP Download it from http www hw group com products hw_vsp hw_vsp2_en html Make sure you download and install their version 2 5 10 It may not be the latest but the commandline startup options are gone in later versions You can read more about using this software as part of how to use LX200 commands with SitechEXE in section 10 1 of this manual Problem How do I set the tracking to Lunar to track the Moon Solution In the overall 0 51 installation package there are scripts including a lunar rate script They re called LunarRate vbs SiderealRate vbs SolarRate vbs KingRate vbs Just run LunarRate vbs and it will track the average RA lunar rate A more accurate way to do this is to go to TheSky software click on the moon and in the information window you have the 184 of 236 RA and Dec Rates Just plug these numbers into the SiTech Offset Rates and you will track the moon very accurately Problem Why is SiTech reporting the slew complete before it actually is This is really prevalent on long slews It will say Slew complete and the ASCOM driver will show it has gone back to tracking the RA and Dec quit moving Yet if I take a 10 Second exposure the stars will trail Solution Two things to help out If you can increase the tracking gain in the configuration it will converge sooner Each system is different on some the default 1 0 is
101. al Catalogue HCNGC Ver 1 11 Copyright 2006 by The NGC IC Project LLC http www ngcic org All rights reserved Permission is given for any non commercial use of this data For commercial use Magazines software starcharts permission for limited use is granted if the following acknowledgement is provided The data used in this product in whole or in part is used with permission of The NGC IC Project LLC http www ngcic org please contact Bob Erdmann at hcngc ngcic org for any questions or clarifications I have also changed the format of their data as well I have noticed that the coordinates do not always result in a target being perfectly centered NGC 7667 for instance so there may be some descrpancies If you find any and have corrections please share them Also there is a file called ICMissing txt If you have extra time on your hands you could update ICO dat IC5 dat with the missing data It was missing from the ngcic org website at the time I downloaded it There are about 100 or so IC objects missing 174 of 236 Appendix D Periodic Error Correction Flow Chart There are two charts The first is the overall flow chart for the Processes It looks complicated but that is because of all the options available and how they relate to each other The second chart is an annotated version of the PECGraph display with the buttons keyed to what they do in the processes The easiest way to see how this works
102. ally e If you don t wait for the worm to line up and press the top left button on the handpad e When Playback is started you will see the status textbox on the left change to Playing 5 Watch the PEC correction happen by examinging the star or image if using a ccd camera It should be much better than before 6 If you re happy with the PEC correction then you can click on the button Save Table in Controller RAM to Flash This table will be loaded each time the controller is powered up 5 2 8 PEC Playback Session If you ve a PEC table saved to flash then this is the procedure to get playback going If you ve an automatic PEC sensor then you can program the controller to start playback automatically on powerup To do this use ServoConfig version 1 1 or later 1 If you don t have an automatic PEC sensor call up the PEC screen in the SiTech ASCOM driver 2 Click the button labeled Arm PEC Playback 3 Wait for the worm to line up with your reference and press the top left button on the handpad PEC will now be active and will be even after slewing the scope 5 2 9 PEC Complex Recording Session A complex recording runs several PE cycles and averages them This method is more accurate for most mounts because the gear teeth are usually not exactly alike Averaging many cycles will ensure the recording is for a typical periodic error Here is what you might consider doing for a complex session assuming motor ticks
103. am to correct for scope declination if you are using relay guiding or a direct guider input from your camera like from an SBIG cable connection or you get twice the proper correction However if you are using ascom guiding i e your autoguider is connected via ascom this is not true so for ASCOM guiding it s best to do the declination correction from within your autoguider program Meridian Overlap This is the number of DD MM SS of meridian overlap before a meridian flip is needed This allows you to track past the meridian if your mount allows it but limits how far if you get into interference Freeze Declination The declination may move slowly for two reasons it will track the declination very slowly to keep up with refraction and if you have two or more stars loaded then it will track to compensate for any polar mis alignment HINT If you are doing a Drift align you may want the Dec axis to NOT make these movements so Freeze Dec during the Polar align and then un check it after the drift alignment is completed Track on Start Selecting this will force the SiTech driver to start tracking on startup It may not be initialized though However this is very handy to keep an Offset Init star centered after you start up Az RA No Wrap For both Alt Az and Equatorial mounts like a Fork Mount but not a GEM you have an additional selection available It is the Az RA No Wrap For an Alt Az mount it will not slew through north
104. ameters from working RAM to the flash ROM XT Reads the configuration from the Flash Rom into the working RAM FC Flash Configure Send 128 more bytes then 2 bytes of checksum Simple Addition of all data bytes sent and it will write the new data to configuration It also reads the new data into the working RAM SC Send Configuration The controller Sends 128 bytes followed by two bytes of checksum This data is what is in the flash not necessarily what is in the working RAM All of the following XX extended commands have a corresponding read command as an example if you type XXL lt E gt it responds with the latitude XXL Store the latitude to the controller 4500 45 deg s north 4500 45 deg s south XXZ Store the azimuth encoder ticks per full circle XXT Store the altitude encoder ticks per full circle XXU Store the number of encoder ticks for the Altitude Motor Encoder to the controller XXV Store the number of encoder ticks for the Azimuth Motor Encoder to the controller XXA Stores the Altitude Slew Rate to the controller XXB Stores the Azimuth Slew Rate to the controller XXC Stores the Altitude Pan Rate to the controller XXD Stores the Azimuth Pan Rate to the controller XXE Stores the Platform tracking rate to the controller XXF Stores the Platform up down adjuster to the controller XXG Stores the Platform Goal to the controller XXH Stores the Altitude Guide Rate to the controller XXI Stores the Azimuth
105. and errors out Solution Try running the SiTechExe software first and then run ACP Yes SiTech takes quite a bit of time to start It is reading information from the controller So probably ACP is timing out before it s done So until I change the code to completely start and then read the information it s best to start up SiTechExe before hand Guide Mode Problem I have an equatorial mount and I m writing my own software to control the scope The declination doesn t guide properly Solution The controller adds or subtracts the guide rate to the current rate It is possible if your declination motor is at it s destination the guide mode gets mixed up Try giving the motor a 192 of 236 command to move far far away with a rate of ZERO This should fix the problem This is not an issue with Servo version 1 6 or later Problem The guiding doesn t seem to work properly Solution Connect up the autoguider and try the test mode on your guiding software Run the ServoConfig software Be sure each of the virtual handpad keys are highlighted when the guider is guiding in a particular direction Be sure that the SiTech controller is in the Guide mode Problem It doesn t seem to guide at all but it is panning or slewing when guide commands are sent Solution Be sure it s in the guide mode This is a software issue if using the ASCOM software or Scopell If in DragNTrack or Equatorial mode hold down the top right key and press the
106. and select ListenSitech neb file from the My Documents Folder ii Verify the camera controls gray out and Listen Mode reported on bottom left margin of Nebulosity Window If Nebulosity drops out of Listen Mode simply re run the file ListenSitech neb At the end of the PxP script Nebulosity will automatically drop out of Listen Mode 3 Call up Features Run Script window in Sitech and set the following parameters a Select how many Cal Stars to image Select at least 6 At least 16 are required to calculate all terms b Set Exposure time in seconds c Set Binning Mode SUGGESTION Move the script window and any other open window out of the upper left part of your screen CalPointXP and PlateSolveXP will open their windows in the upper left corner of your screen and if something else is already there they may end up being covered up 4 Click on Make PointXP Run to build script If a script already is resident in the window on the right you may get a message that asks if you want to overwrite it or replace it Click Yes NOTE Occasionally overwriting the script will kick Nebulosity out of Listen mode If that happens simply re run the file ListenSitech neb from within Nebulosity click on Edit Run Script and select the file ListenSitech neb 5 CalPointsXP graphic will open showing location of init points a If desired to keep CalPointsXP graphic visible of init point locations click on Keep Window o
107. anual If this is not correct change the direction using Edit Parameters button on ServoConfig 2 Make sure that pressing the right button moves the telescope even more west goes below horizon if still looking at the western horizon If this is not correct change the direction using 72 of 236 Edit Parameters button on ServoConfig 3 Exit ServoConfig and call up SiTechExe this assumes lat and long are set in the SiTechExe Configuration 4 Manually point to a star in the Western Horizon Perform an offset sync You may get a window suspect bad GEM init Click on YES Click on Keep window up once the SiTech init window appears Make sure the button labeled Looking West is active Perform an offset init 5 Now you should be able to GoTo and track properly while looking west 6 Now if you want to view on the East side you will have to manually do a meridian flip Center on a star and perform a Synch again You ll get the Suspect bad init again Go and say Yes Make sure the Looking East is active Perform an Offset init Now you can view on the east side all you want and things should be fine 73 of 236 5 ADVANCED FEATURES The following sections provide additional details on areas previously introduced but annotated Advanced Features 5 1 SCOPE TAB 5 1 1 PointXP Mount Modelling An application called PointXP is built in to SiTech exe that allows measuring and correcting for many errors
108. arameters are stored to the flash ROM Use X and Y for module address 1 If the module address is 3 use T and U for address 5 it s V and W Description of the bits for the XBits and YBits if 1 the motor encoder is incremented the other direction if 1 the motor polarity is reversed if 1 the azimuth or altitude encoder is reversed if 1 x only we re in the computerless drag and track mode if 1 y only we re in the computerless slew and track mode no clutches must use handpad to slew must be in drag and track too 4 if 1 x only we re in the tracking platform mode 5 if 1 x only we enable the hand paddle 6 if 1 x only hand paddle is compatible with New Hand Paddle allows slewing in two directions and guiding 7 if 1 x only we re in the guide mode The pan rate is added or subtracted from the current tracking rate Note about the Guide Mode If PC software puts the controller in the guide mode and you are controlling an Equatorial mount you must give the declination motor a destination even if you want it to be stopped If you want the declination axis to be normally stopped give the declination a far far away goal and set the speed to zero This is because the controller adds or subtracts from the current speed and direction and the controller gets confused if the axis is at its destination This is changed inf servo version 1 6 and this is automatically done for you in the controller The Y_Bits bits 4 7
109. are the digital input status for the 4 digital inputs from the radio handpad reciever This is only available if you re using servo version 1 6 and also if you have a handpad reciever connected WWNre 181 of 236 Appendix F Troubleshooting Initialization Troubleshooting Problem My GEM mount is physically positioned in the Looking West position and when I click on a star in the west and tell it to sync on it I get a warning message window telling me Sitech thinks the mount is actually aimed to the east and do I REALLY want to do this What do I do Solution Make VERY sure that you are actually trying to sync on a star in the West DST may be wrong or the date or time in the PC or in your planetarium program And make sure the Looking West button in the InitPoint wondow is checked You might also want to verify the latitude setting in the config pages is for the appropriate hemisphere 9for the north and for the south Then Click on Yes to the message window or let the countdown timer simply count down This sometimes puts the init timer in manual so if that happens simply click on Offset Init or CalStar init and then click on OK This should fix the problem but if things are still screwed up close Sitechexe you may have to disconnect your ASCOM planetarium Program first and opwn_ the Sitechcfg file its at C Program Files Common Files ASCOM Telescope Sitech Then change the OFFSET terms to be equal t
110. at best with a good mount you may be able to get 1 arc minute of polar alignment If you need more accuracy the drift method should be used Special thanks to Ralph Pass who published this http www rppass com align pdf 90 of 236 5 2 2 Run Script The SiTech ASCOM driver has a powerful script feature You can pan the Lunar terminator using relative pan commands Pan the Veil Nebula with absolute pans write your name with starlight etc Making the scripts is as easy as moving your scope or the virtual scope during the day and clicking on various options Ei Script CurrentCommand Stopped Add Slew Slew 20 47 10 30 1 4 00 0 06 Sound C Program Files Common Files 45COl Add P Prompt Press OK to start panning the Veil Neb Stopped Adan Pan 20 46 30 30 33 03 0 06 Add Anchor Pan 20 46 15 30 44 25 0 Load Script Add SlewT o amp nchor Pan 20 45 55 5 31 Pause __ toad soit 43 01 31 08 Stop UnPause F Add PanToAnchor Play Save Script Add Pan Relative Add Pause Clear Then Paste M Make a Point lt P Platesolve Script Add Prompt s E Se How Many Cal Points xposure Binning Make PointXP Run Add Wait GE P 2 4 Add Sound F Use SiTech Init Window Do a single photo init Add While 3 Add Loop Click here for HELP Cancel Colors The information below addresses how to use the powerful scripting capability in SitechEXE However in the scripting window there is a special section that creates a
111. ate a simple GoTo Tracking Database to a JavaME program so the scope can be controlled by a cell phone We monitor the SiTech forum on Yahoo at http tech groups yahoo com group SiTechservo where any SiTech user can suggest features and fixes to the system 16 ACKNOWLEDGEMENTS The SiTech System owes its existence and continued development to Dan Gray and the many volunteer members of the SiTech Users Group As one of those volunteers Don Westergren assembled and edited this manual update and included the following acknowledgements If the list overlooks significant contributors it is not intentional Listed in alphabetical order thanks to Mel Bartels has provided longstanding development and continued support of so many telescope mounts and drive systems software and commercially making the SiTech system components available to all at http www bbastrodesigns com BBAstroDesigns html Dan Gray developed the SiTech System and wrote updated the software as well as answered thousands of questions from users He started development of the software in 2005 and released first software in 2006 Since then Dan has made the SiTech System into the most versatile and feature rich mount drive system available to the Amateur Astronomy community John McClusky has developed the routines for operating the Rotator and Focuser controllers from SiTech John also has helped a lot in reviewing code for Dan Jim Roe set up and maintains the Google sit
112. atesolveXP as part of its algorithm to calculate the coordinates of the center of the images that will be taken during the scripted routine When you click OK any new data or configuration entered in any tab is saved in a file named Sitech cfg in the Ascom Sitech folder If you have more than one camera you may be using or more than one telescope or both you can save backup copies of the config file using the Save Backup Config button at the bottom of the page and then re load them using the Load Backup Config button 67 of 236 4 11 5 Setup ASCOM amp Troubleshooting Tab Setup SiTech ASCOM Driver VO 54L Telescope Info Mount Info Scope Encoders Miscellaneous Ascom and Troubleshooting Focuser Rotator Potentiometers Log Serial Communications J LogASCOM ASCOM AxisRates to AzA and Dec J Log Debug Stuff I Slew Settling Time 0 Priority Above Normal J Proskos tion hy Instant Total Pulse Guiding T sPulseGuiding Always returns false Log Gurley Interpolation Invert Gurley Interpolation I OK Cancel Help This tab provides options for supporting different logging options used for troubleshooting and other misc settings Its is recommended to not have the following checked unless you are working with Dan on gathering data for troubleshooting a problem you are having since the logging can slow down the comm routines between SitechEXE and your PC Log Serial Communications
113. ation from the RMS that this particular star has Viewing the Cal Stars makes it easy to see if a particular calibration star s is causing problems You can select multiple stars by clicking on the line of text just not the Used portion The line will turn red You can then delete your selected stars if you want Note Since the names of the stars aren t sent to the SiTech telescope driver then the names are found by searching the co ordinates of the star The star name comes from a file called C Program Files Common Files ASCOM Telescope SiTech Database CoorToName dat If this file is not there all star names will be No Coordinat If you don t have this file you can copy your NamedStars dat file to CoorToName dat If you re so inclined adding more stars to this file would be worthwhile Be sure the co ordinates are from epoch 2000 Please share your work on the SiTech users group if you do this EE DisplayCalStars No Star Name Date Time RA IDec Ang 1 No Coordinat 07 27 27 21 36 21 02 43 216 35 176 42 S02 01 40 Used INo Coordinat 07 27 27 21 40 38 23 04 08 05 151 46 z 5 z 21 Used INo Coordinat 07 27 27 Z1 43 06 23 05 215 27 164 41 Sere 01 40 Used No Coordinat 07 27 27 21 46 03 23 28 228 55 173 33 223 03 07 Used No Coordinat 07 27 27 21 49 05 00 13 214 14 164 43 52 01 40 Used No Coordinat 07 27 27 21 51 09 00 08 208 39 150 43 239 703 32 Used INo Coordinat 07 27 27 21 53 13 00 39 2 4 49 148 57
114. ation with the Argo Navis Now align the Argo Navis following the Argo Navis instructions Once alignment is complete you can select an object using the Catalog menu of the Argo Navis Now press both the ESC and RTN keys at the same time The scope will GoTo the selected object and start tracking If the object is not centered you can center it using the handpad If the scope is moved manually you can return to the last object by pressing the two buttons again 10 10 USING THE HANDPAD AS A WIRED HANDPAD There is a 6 position modular connector on the end of the handpad This can be connected to the SiTech Controller directly Any SiTech handpad will work for this whether it has radio components or not If your handpad has radio components the radio is disabled when connected to the SiTech controller This can be useful if the battery runs down in the middle of the night with no 7 11 around the corner to purchase a new one or if there is interference for some reason You can purchase the handpad without the radio components It will then simply serve as a wired handpad You will not be able to use the guide mode from the handpad from software only and then you will have no indication of which mode you are in unless it is on screen It will not work properly as a wired handpad on Mel Bartels Stepper System 10 11 ACCESSING THE RECEIVER I O There is a 6 position modular jack which has the digital inputs and outputs on it The
115. atitude the scope would be at if the primary axis the Az axis for Alt Az and the RA axis for an equatorial was pointing straight up To explain further let s say your alt az scope is at latitude 45 degrees but the South end of the base is 1 degree lower than the North end of the base This is the same thing as having the scope at latitude 44 degrees and being perfectly level There is a text box called Scope Latitude and Scope Longitude It s hard to have accurate results for the scope longitude so don t pay too much attention to this but your scope latitude is crucial When you add the 2nd star to the matrix get the habit of looking at the scope latitude If you have an equatorial telescope theoretically the scope latitude will indicate how far you are away from the celestial pole If you have an alt az scope it should agree with your site latitude within the errors of your mounting levelness 4 9 5 Know when to use Cal Star Init Points and when to use Offset Inits It is extremely important that you understand this If you follow these directions you can have up to 1 or 2 arc minutes of GoTo accuracy as well as extremely accurate tracking for long periods of time if you have a reasonably accurate telescope mounting Basically the ground rules are Use Cal Star Inits if you are trying to model your mount or to correct for the mount not being level for an Alt Az or to correct for not being accurately polar aligned for an Eq
116. be updated by 1 14 Rotation angle does NOT have to be entered since the plate solution routine will figure this out Darks are also 79 of 236 not required since the program does its own image optimization PlateSolveXP has been integrated by Dan Gray into the SiTech system He has developed routines to send images from various cameras to the program Solved image centers are sent to PointXP for mount calibration There is additional detailed information on PlatesolveXP in the appendices of this manual For integrated platesolving with SitechExe the telescope focal length and camera pixel size and array sizes are read from the SitechExe config setup so be sure to input this information there For scripted operations described in the next section the binning is also provided by SitechExe to PlateSolveXP For scripted operations nothing is used from the Fits header since the RA Dec is also obtained from SitechExe Starting with version 1 13 there is an object information feature do a plate solve then press the object info button and move the cursor over a star and also an edit parameters feature complete with a built in help button Defaults usually work great however The program now builds an ini file so if you update from an earlier version your previous updated parameters will be reset to defaults and will ned to be updated again Blank images like for clods passing through used to crash things but not now You can also save the
117. cently added point is bold You may right click on points to toggle them on yellow or off red Only the on data points are used to calculate the calibration line Write Stars writes all the data to the file Focuser Calibration in the SiTech directory The format is raw temperature focuser position Use 1 or Don t use 0 Clear All Stars clears all data from the window It does not erase the Focuser Calibration file Read Stars adds the stars from the Focuser Calibration file NOTE they are only valid if the absolute focuser position is exactly correct 119 of 236 8 2 FOCUSER OPERATIONS Before use use Servoconfig to set the encoder counts for inch of focuser travel Make sure the counts increase as the camera eyepiece moves outside focus 8 2 1 First Time Startup WITH zero position sensor 1 Confirm that the out button moves the focuser out If motion is reversed change the direction settings for the controller using ServoConfig exe 2 Click the Parameters tab then the Setup Dialog button Check the Focuser has microswitch checkbox and then the appropriate radiobutton indicating the direction the focuser must travel to change the output of the sensor This will be used so the focuser travels in the correct direction when it is being initialized to the zero position Then Click OK 4 Indicate whether the focuser should automatically initialize the focuser to zero whenever the
118. confirm the setpoint 4 To use another E C simply put it in then left click the corresponding MOVE TO setpoint the ones on the top You may tweak the focus with TCF still on using the window or handpad if necessary 5 Should the focuser ever get lost or confused you can always focus with the window buttons or handpad then click the bottom SET FOCUSER setpoint button to tell the focuser the correct setpoint TCF can be on or off although if it is far off it is better for TCF to be ON 8 2 7 To calibrate TCF 1 Put in the eyepiece or camera you will be using A camera or high magnification eyepiece is best 2 If you are refining a calibration TCF can be ON Otherwise turn TCF OFF 3 Click the top MOVE FOCUSER setpoint to move to focus 4 Select the Temp Compensation Tab 5 Tweak the focus to perfection 6 Click the Add Temperature Calibration Point button The latest point added is bolded 7 Continue adding calibration points throughout the night as the temperature drops The more points the better the line however garbage points will give a garbage calibration 8 You can activate yellow or deactivate red specific data points by right clicking on them Deactivated points are not used in determining the calibration 9 Click Calculate Calibration Line to calibrate the focuser The calibration is automatically saved to the focuser cfg file The Write Stars button saves your calibration points t
119. cope and I m trying to use the Argo Navis but the encoder locations on the Argo Navis don t change when I move the scope Solution Be sure the SiTech controller is in the SlewNTrack mode Problem I can do a normal Argo Navis Initialization but the tracking and GoTo s are inaccurate Solutions Set up your telescope in the DragNTrack or SlewNTrack if you don t have scope encoders mode Be sure to get that working well If the DragNTrack or SlewNTrack doesn t work properly neither will the Argo Navis mode Be sure the Argo Navis is set up 191 of 236 properly Check the encoders on the Argo Navis They should change at the same angles as you move the telescope If not check the Argo Navis encoder resolution It should be 18 000 Check the motor and scope encoder values in the SiTech configuration If necessary use ServoConfig and Ticks Determination to find the encoder values Remember the math in the Servo controller has been proven time and time again it is a mechanical or a configuration problem Problem When I do a slew the telescope moves close to the object then moves again about the same distance in azimuth or altitude Solution Sounds like one of your scope encoders is not working properly Check the scope encoders and or wiring This is easiest using the ServoConfig main screen Sky Commander Troubleshooting Problem I want to use my Sky Commander on my SiTech mount I don t know how to confi
120. cope encoder be a faster routine for pmo hi rez enc 1A moved volts from direct mem to indirect mem 1B added r a scope encoder byte increment dec to old mem location of volts 1C changed the r a scope encoder routine to make faster 1D Made ext int 0 and 1 hi priority 0 IS 2g 2g 2g 2g K is K K K K K K K K K K K K K K K K K K K K K K K 3 Version 3 1 final 1 Made the dec alt scope encoder be a faster routine too 0 IS 2g 2g 2g K K K K K K K K K K K K K K K K K K K K K K K K K bi Version 3 2 working on tick management 32B Fixed ArgoNavis Bug wouldn t get offsets only rates jumped to wrong label Argo Navis still doesn t work Version 3 2C Adding safety if motor output on but no movement we stop after delay Version 32D Fixed PEC bug if changes over 127 per segment Made it impossible to save negative slew pan guide rates to flash 234 of 236 0 FIG 2g 2g E K E K K K K K K K K K K K K K K K K K K K K K K K 5 Version 33A Fixed ArgoNavis bug Added offset init for argonavis Version 33B Fixed new bug in floating point routines made the azimuth rate pan and guide work bad as a function of altitude Fixed the negative guide rate for GEM s I think Version 33C make 3 speeds with wired handpad Version 33D Trying to make stop tracking work with dnt an modes 0 IS 2g 2g 2g 2g 2g K K K K K K K K K K K K K K K K K K K K K K K K gt V34A Change in comm protocol to allow
121. cted False Result MsgBox We re all done now 0 SiTech Offset Tracking End If End If if Didit 0 then MsgBox Didn t find object to track Did 146 of 236 you center it on TheSky Screen Next End Sub lt script gt lt job gt lt package gt 147 of 236 13 SATELLITE TRACKING Brent Boshart wrote an outstanding program called SatTracker that was built to allow tracking satellites with Meade telescopes or any scope that responds to the LX200 command set Unfortunately SatTracker is not ASCOM compliant and SitechEXE does not directly support LX200 commands Mons Sariento built a converter named EQMOD for his mount that converted LX200 commands to ASCOM That worked GREAT but was a bit cumbersome to use So Dan updated LXtoSitech exe to include the LX200 commands used for satellite tracking Refer to section 10 of this OPERATIONS manual for setting up and running LXtoSitech exe SpaceTrack TLE Source hyou must register to get auserlD TLERetriever exe Lx 200 Cmds Virtual SatTracker exe Com PortS HW _VSP Le2o0 Crmids LXtoSite ch exe iconmverts LE2ZO00te ASCOM Site chEXE exe ASCOM mads Meanwhile Brent provided SatTracker as freeware You can join the Yahoo Group for SatTracker to get access to the file and a very active user group Download SatTracker and install it http tech groups yahoo com group satellitetracker There is a VERY active user group at the Ya
122. curate alt az mount You can enter these two numbers in your configuration latitude and longitude and now your alt az scope will be accurate with only a one star Offset Init Focuser Position in engineering units you ve set in ServoConfig ticks per inch ticks per millimeter ticks per fortnight or whatever SAxis Error Secondary Axis Error This is the deviation of your altitude or declination axis from its setpoint i e the target where Sitech commanded it to actually be If you ve selected the drag mode this will be zero as there is no setpoint PAxis Error Primary Axis Error This is the deviation of your azimuth or right ascension axis from its setpoint i e the target where Sitech commanded it to actually be If you ve selected the drag mode this will be zero as there is no setpoint SAxis Position Secondary Axis Position This is the position of your altitude or declination axis PAxis Position Primary Axis Position This is the position of your azimuth or right ascension axis in degrees ScopeAz Position This is the current local Azimuth of the telescope ScopeAl Position This is the current local Altitude of the telescope 42 of 236 4 5 FEATURES TAB Polar Align Add Stars find AlOffset Add Stars find AzOffset Do GEM Flip Run Script Controller Stuff PEC Control Offset Track Rates Handpad SlipMode T Colors Close STOP Stopped frp o O a gt O m 3 io Ba
123. d Collective Item from Controller Buffer Show Current Collective Item I Arm PEC Record Load Collective Item from File Buffer Show Average IV Arm PEC Playback Load PEC Collective Show Latest From Controller IY Read Cntrler PEC Table into Crtrler Buffer Save PEC Collective of n Show PEC File Buffer I Send PEC Table From File Buff to Controller Load File Buffer from PEC File Send Averaged Table Buff to Controller You have 5 in Collective Save Average Buffer to File Save Table in Controller RAM to Flash Delete Collective Item 1 2 Save Controller Buffer to File Stop PEC Playback Save Collective Item to File Ee What the heck is all PEC AutoSyne Sensor OFF Colors IERIE aie this This screen looks complicated at first but after spending some time at it it will hopefully make some sense and will certainly be worth your time so please hang in there In the graphic area the magenta lines show the raw results of 5 worm cycles of guiding data that were recorded The buffer this data is saved in is referred to as The Collective The dark blue line shows the averaged and smoothed data from those 5 raw pec training runs 98 of 236 On the left of the bottom section of the window you see a column of buttons These buttons all have something to do with the controller In the middle of the bottom section of the window you see another column of buttons These buttons all have something to do with the c
124. d Scope Commun Ra 05 46 29 3 H Sep HrAng 11 59 59 Dec 00 06 31 Focuser Field Rotate Motors Automatic All of the capabilities on this tab except for Do GEM Flip should probably be considered Advanced Features since none of them are mandatory for basic operations except for the GEM Flip 4 5 1 Polar Align ADVANCED FEATURE This button will assist you in performing a Polar Alignment for an equatorial mount Some users will find this easier than doing a drift align and some will find using the PXP capability better More details on this will be in the Advanced Features section 4 5 2 Do GEM Flip This button will command a German Equatorial mount to perform a Meridian flip Be sure any 43 of 236 cables are rigged to not get tangled or snagged Use this button if you do not want to use the automatic GEM Flip capability that will be addressed in the Configuration Tab for instance if you have to manually tend cables etc and do not want to be surprised by the mount doing anything automatically GEM Flip Motion If the mount is initially on the looking east side scope is on the west side looking east counterweights are on the east side a GEM Flip will rotate the RA axis till the counterweights are down and the scope is up At the same time the scope will rotate in Dec until it is looking due north One axis may get to this position before the other and it will stop and wait till the slower axis com
125. d target Already Initialized you ask How do I do that Well that s where the Sync button comes in Aim the telescope at a known star use the handpad to manually slew it or de clutch and move and re clutch If you just click on Sync without aiming at something above the horizon and if the loaded target is below the altitude limit set in the configuration windows you will get a message telling you its below the altitude limit While you CAN sync to something below the limit you will be lying to the software about where the telescope is pointed so all bets are off on what it will do 50 of 236 4 7 INITPOINT WINDOW Assuming you selected a target the scope is actually aimed at you will get the InitPoint window shown below There is a timer counting down till the init actually happens This needs to be this way to remain ASCOM compliant where no popup will remain up and possibly freeze the ASCOM driver if it is being controlled from remote controlled software It s only a short 5 second timer though and the status of the timer and the type of initialization that will be done when the timer finishes is shown in the second from the left button the example shows two seconds left till a Simple Offset Init will be done If you want to stop the timer to verify everything looks ok click on the far left button that says Keep Window Up Manual Control Don t worry you will get used to clicking on the left button when
126. d the scope If they have a Refocus using the window buttons or the handpad b Click the bottom SET FOCUSER setpoint button to tell the focuser that you are really still at Setpoint 1 Remember it is the relative positions between setpoints that is important not the absolute position 9 Repeat steps 5 through 8 for each additional eyepiece camera and filter combination eke Click SAVE PRESETS to save your presets 8 2 6 Startup instructions for a typical night 1 Open the focuser window Put in the eyepiece or camera E C you wish to use and click the setpoint corresponding to that E C 2 Turn on TCF with Move to Focus option will work to a perfect focus only if the following are true 1 The focuser position was updated with an absolute zero position init sensor or if it does not have an absolute zero position sensor the focuser ewas not moved since it was last shutdown AND 2 the scope was focused when the TCF was turned off last AND 3 you have and accurate temperature calibration saved 121 of 236 a If the focuser senses a large shift it may ask you to confirm the setpoint b You may tweak the focus using the window or handpad if necessary Do not turn off TCF to tweak the focus and you don t have to do anything after tweaking 3 You may also focus manually prior to turning on TCF In this case start TCF with the Already Focused option If the focuser senses a large shift it may ask you to
127. dded Separation of ra az encoder action with dec alt action 11 Changed 3rd star in matrix to remain fixed as 3rd entry instead of latest 12 Added Nutation Aberration to the local database 13 Added Pressure and Temperature to the refraction routine Do eee E E K K ee ee K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K 0 45 same as 0 44 1 Add RotatorAngle OffsetSync LoadStarSync for john mcclusky 2 Made hot config not move scope when changeing critical things like lat long telescope type 3 fixed bug in Meridian flip sound plays when new sync 4 Fixed scripting Pause indicators not working right and scope pad needs to pause unpause 5 Fixed script prompt window goes behind other windows 6 Inspect Inits could get into trouble when clearing all init points Tries to do offset bad idea Fixed 7 Made inits work in the precise mode if they ve configured for polite mode 8 Make controller information screen with terminal mode viewing current voltage etc 9 Now Park Setpark and Unpark works on 2nd focuser EEEE KE E E K E E K E K E K K K K k K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 0 43 1 Play some sounds Slew Ended Slew Pan Guide MFlip in 1 minute Lost Communication KEKEKE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K
128. de offset calculated on second star and then left alone Tried to make auto track on start and then track on exit don t think it works ran out of time Made a reporting inits feature KKK K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K K 3K 3K 0 17 Found and fixed trouble with east calc z123 EEEE KE E E E E KE K E K E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K FK K K K K 2K K K 0 16 Found possible divide by zero in average altitude offset Found I should leave the alt adder same as before so changed back to previous EEEE E KE K E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K FK K K K K 2k K K 0 15 Fixed the elevation conversion from metric to english Added update text boxes only when changed This helped memory usage Working on the time stamp issue now time stamp comes from the controller Working on error being taken up each loop instead of over 10 seconds Error amount has display of 1 seconds now Split arrow keys for slow and fast when letup scope stops Found offsets were being re added every time fixed Found TheSky sends refracted co ordinates so made a Refraction option Made Unpark work correctly even when unparking right away TheSky 6 Polar alignment routine Added Slew Pan indicators Added Freeze Declination option
129. dian instead of average Changed in Telescope the CommTime uses the median instead of the last interval 053K Working on Gurley interpolation 053L AArt done not tested 053M AAtt bug fixed Nebulosity scripting finished So now the new feature that does automatic plate solves should be finished except for ccdsoft It works with MaximDL AArt and Nebulosity Added line highlights in the scripting as it plays 053N Made option to NOT reverse the guide rate while looking east Added F O V Calculator Stopped axis rates or axis moves if below horizon Fixed the OnScreen Virtual Buttons problem Fixed reading another pempro file actually seemed to work fine 053P no O Log RA and Dec on the move axis command 053Q Hopefully AArt waits for the new fits file Added auto sizing of script window if you make it longer can see the complete line of script text 053R some stuff 053S Working on Gurley interpolation Added a check when unparking does the park pxp file have the same kind of scope if not doesn t use 215 of 236 053T Working on Gurley interpolation caught the logging exception Changed logging reporting KEKEKE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 052A Fixed focuser bug the ascom part now keeps appending the commands so I now read the last line 052B Made Pulse Guide work better hopefully Fixed scope location display on PointXP All Sky chart equatorial
130. display down in the lower right corner click on Load PemPro File Select the ppc file you just saved and it will load e If you have file buffer checked it will also show up on the graphic area and an orange dotted line Verify it looks like the plot in PemPro If not you may have to invert the file in PemPro and re save it then re load the file into Sitechexe again e Inthe middle column of buttons click on Load Collective item from file buffer Then make sure the averaged buffer is checked and you should have a nice smoothed PEC curve e Load the curve into the controller using the Send averaged Table Buffer to Controller button on the left And after its uploaded click on Save controller Ram to flash 8 Make sure that the data in the controller matches what was sent to it e Click on the Read Controller PEC table into the Controller Buffer 200 of 236 e Make sure the Show Latest from Controller is checked on the right side The curve should be the same as the averaged buffer curve 9 From now on if you have an autopecsync detector just make sure use autopecsync is checked on the PEC graphic page and it s all taken care of Otherwise after starting up the controller you should simply do a single manual PEC sync marks lined up and use Top Left handpad button e The biggest issues with this are usually not getting the Pec Sync done correctly so pay particular attention to getting that
131. do this inside without being connected to anything to get used to it Satellite Tracker v2 4 9 Freeware Meade LX200GPS File Satellite Telescope View Options Help Object Data NORAD No 31207 Launch Yr No 1999 025 T Epoch 47 235203 Julian Date 2455088 113227 Local Time 14 43 02 7 UTC Time 14 43 02 7 Azimuth 328 703 Elevation 17 157 Range 1916 986 km Velocity 26868 76 km hr Latitude 12 6682 N Longitude 7 8070 E Altitude 802 509 km Mm AA Wh m49s Dec 54 43m 5 s Sun North West Descending Location 410 2 3 Atitude m Sitename Latitude N Longitude E UTC Offset EE hours TLE Data Satellite Name FENGYUN 1C DEB Sep 13 2009 14 43 02 7 Set lt lt Close Monitor f All Above Horizon Select Object M Elevation gt 25 H Altitude Low v I Ascending Only F In Sun Only l Favorites l Never Observed Direction NW Reset Filters Geostationary Only J List by NORAD Refresh List FENGYUN 1C DEB 3 object s View Plan NV 13608 total Observation Log Sky World Map Map Predict Pass View Plan TLE File Download Continuous Batch Predict Open Fil Telescope Tracking e START Tracking R A Tracking Stopped Dec Tracking Stopped Timing Offset sec at ot an Fa Alignment Adjustment steps ED co ronal P ca api Up Joystick Adjust Mouse Adjust Tracking Method Leap Frog Tele
132. e after a slew before expecting perfect tracking Initial testing of equatorial mounts using the Gurley encoders indicate that unguided astro photography can be done for a few minutes with most mounts but exposures longer than two to three minutes benefit from guiding Autoguiders with 1 second or longer exposures do not seem to interfere with the Gurley IPE corrections Autoguider aggression can be set for about 30 in both RA and DEC to correct for slight drift The wiring diagrams for the cables for the Gurley encoders can be found in the appendices of the SETUP Manual The benefits of using the Gurley encoders in the IPE Mode requires that Periodic Error correction routine be turned off in the SiTech controller Go to the Features PEC Control screen PECGraph and press Stop PEC Record or Playback The best way to assure that the PEC routine will not disrupt the Gurley IPE routine for future sessions is to clear out the PEC table in the Controller On the PECGraph page click on the Clear PEC in Controller button top left part of the buttons area and then click on Save Table in Controller RAM to Flash button 110 of 236 which is nearly the bottom button in the lower left corner 7 1 Encoder Mounting Accuracy First the ONLY way to make sure the gurley is sensing ONLY the rotation of the axis it is measuring is if it is axially coupled to the axis shaft That means the shaft of the gurley is stuck into a hole in the
133. e error between the optical axis of the scope and the altitude declination axis 2 Hub Z1 This is a fabrication error It is the error between the azimuth RA axis and the altitude declination axis 3 Dec Imbalance As the scope moves in Altitude declination the scope may flex Also will correct for a non centered encoder 4 RA Imbalance As the scope moves in azimuth RA the scope may flex Also will correct for a non centered encoder 5 Dec Transvers Same as 3 however it is as if a weight was on the side of the scope 6 RA Transvers Same as 4 however it is as if a weight was on the side of the scope 7 Dec Droop cos Corrects for the Cosine of the Declination or altitude as your secondary cage or camera flexes position during different altitudes or declination 8 Dec Droop Sin Same as 7 but the Sine instead of the Cosine 9 12 Alt Sin Cos These parameters can have the same effect as flattening the bottom of your azimuth axis It can help an alt az scope more than an equatorial scope As you use PointXP the star locations are plotted so you can see how they fit and how they contribute to overall accuracy The display also gives you control of which terms are active and several button controls to clear load save or display information Pay particular attention to the Model Sensitivity box at top center You want to keep this box green as you turn the terms on or off on the left and accumulate more Ca
134. e Buffer I Send PEC Table From File Buff to Controller Load File Buffer from PEC File Send Averaged Table Buff to Controller You have 5 in Collective BE Save Average Buffer to File Save Table in Controller RAM to Flash Delete Collective It i ave Table in Controller o Flas elete Collective Item Gave Controler Buffer to Fie Stop PEC Playback Save Collective Item to File E Tamni atthe heck is al PEC AutoSync Sensor OFF Colors Pte aies lie le this 46 of 236 4 5 6 Offset Tracking Rates ADVANCED FEATURE The ability to change Offset Tracking Rates to track fast moving objects fast relative to the stars like comets and some asteroids is built into SiTech Since this capability is not mandatory for basic telescope operations it will be explained in more detail in the Advanced Features Section However since it is a VERY useful capability be sure to come back to it S RateA djust m IF you Don t use the DRAG mode IN fia Mins Drifted 2 Are Secs Calculate Offset Tracking Rates Arc Seconds Per Second Works on Alt Az scopes with RA Dec too Rate To Zero Declination IN fia Mins Drifted Right Ascension 2 AteSees Calculate Rate To Zero oc DER Dismiss HELP ME SPOCK Colors If you use the DRAG mode Tracking Calibration Rate To Nominal Servo Cal to 1 0 Recommended ServoClock Ratio 0 08 Re Sync Sav
135. e ServoCal 47 of 236 4 5 7 Colors The colors used in the windows for SitechEXE can be customized using this button to open up the color adjustment page This is not mandatory for basic operations but its easy to do and you may find it easier to use SitechEXE if you change some of the colors ColorSelection Main Window ForeGround Main Window BackGround OK Button ForeGround Button BackGround This is aButton_ Label ForeGround This is a Label Label BackGround TextBox ForeGround This is a TextBox TextBox BackGround GroupB ox ForeGround fg te rn Eny GroupBox BackGround Sample Text Sample TextBox CheckBox ForeGround F checkBox1 CheckBox BackGround Clicking on the different buttons on the left side brings up a color choosing page to easily change the colors associated with the item named on the button Examples of buttons labels text boxes etc are on the right side The color picker window is shown below Basic colors E Gey eee ee tee Fe ee Et hee GC ERE EEE E EE EEE EE E LE E f imi iu Custom colors ee ae ee E Hue 160 net BEES eS aa w SS Pe eel D Color ColorlSolid arr fo Blue fo af Cancel aa Help Add to Custom Colors 48 of 236 4 6 GoTo SYNC TAB This tab provides a handy standalone capability to call up and use a built in database of stars and VO 54L al ae Select File Line ScrollFileN ame Star Messier Nec ic
136. e SiTech ASCOM driver Select whether you have an automatic PEC sensor or not at the left side of the screen Start guiding on a star either manually or with an autoguider Click on the button labeled Arm PEC Record e If you have an automatic PEC sensor wait for it to line up and recording will start automatically e If you don t wait for the worm to line up with your reference and press the top left button on the handpad When recording is started the status textbox on the left changes to Recording During the next revolution of the worm the controller will record all of your button presses from the handpad or from an autoguider e At this time click on the check boxes at the right so the Average 5 collection items and Current Collection item are displayed on the graph e Once the worm revolution has completed The status will go to Idle and you re ready for your next record session Click on the button labeled Read Controller PEC Table into Internal Buff After the table is loaded click on the button labeled Load Collection Item from Controller Buffer You ll notice that you will have one more item in the collection Repeat steps 3 through 6 as many times as required We recommend about 6 8 record sessions Now you will have several PEC tables in the Collection You may want to save the collection by clicking on Save PEC Collection At this point run through all of the PEC tables in the collect
137. e a test on this later 34 of 236 4 SiTechEXE Introduction Double click the SitechEXE ICON on the desktop After SitechEXE opens you will see the first left of the following 5 vertical panels This vertical Panel is the Sitech window The title bar at the top shows the version of SitechEXE that you are running The window has two parts a tabbed area and a common area The 5 tabs at the right side allow selection of different controls and displays from each of the panels You will only see one of these tabbed areas at a time The common area at the bottom provides the same information for any tab selected PointXP O Starfs Loaded Controller Mode SLEW UnPrk SetPrk k Run Script l Offset Track Rates Add Stars find AlDffset Add Stars find AzDffset Do GEM Flip Controller Stuff PEC Control Handpad SlipMode _ Byuo9 audgo109 samea Colors STOP Stopped Select File Line Star Messier NGC IC Description STOP Stopped ScrollFileName f SMtrTix 29487179 PScpTix 33418803 SSopTix 33418803 SSlwSpd 01 05 29 PGidSpd 00 00 13 SGidSpd 00 00 13 Reading Servo Parms Reading Servo Parms Ra 12 50 57 0 Faking Servos H Ra 12 52 03 7 Ra 12 52 35 3 Ra 12 52 51 1 Ra 12 53 15 7 Bop HrAng 12 00 00 H Scp Hr ng 12 00 00 Scp HrAng 12 00 00 Sep Hr ng 12 00 00 Sep Hr ng 12 00 00 Dec 57
138. e controller that you used ServoConfig to send to and save in the controller Terms starting with a P are for the Primary axis RA or Azimuth and those starting with an S are for the Secondary axis Dec or Altitude Eg H PMtrTix 20924183 SMtrTix 231 89662 PScpTix 2081 7627 SScpTix 53939404 PSlwSpd 01 32 17 SSlwSpd 01 23 16 PPanSpd 00 03 05 SPanSpd 00 02 47 PGidS pd 00 00 18 SGidS pd 00 00 17 Change Config audga jor gt Ra 02 42 45 0 Sep Hr amp ng 1 4 45 31 Dec 89 1 8 08 Focuser Field Rotate Motors Automatic At the bottom of the tabbed area is a button labeled Change Config This is the access to the SitechEXE configuration screens 57 of 236 4 11 SiTechEXE CONFIGURATION SCREENS Clicking on the Change Config button will bring up the following Setup window eS Setup Sifech ASCOM Driver VO 54L Telescope Info Mount Info Scope Encoders Miscellaneous Ascom and Troubleshooting Focuser Rotator Potentiometers Name Statiner Description Scope Controlled by SiTech Servo Controler M Optical Info M Geographical Information Aperture 0 36195 Inches Longitude West IV 95 07 59 J East Optical Area Ber Latitude North 23 34 29 South Focal Length 15494 Meters Elevation Feet J 7 3152 V Meters OK Cancel Help The Setup window has a series of tabs at the top to make access to the various configuration information m
139. e discussed a bit more in the information below The altitude offset is how much off of the zenith the azimuth axis is aimed for an alt az mount There are two additional buttons on the right side of the InitPoint window Just Load Star No Terms and Calc Only Offsets Align are capabilities that are used as part of using the PointXP tool and will be discussed in detail in the Advanced Features section on PointXP At this point before you press on you should read up a little more about Inits in the information that follows since you want them to become second nature 52 of 236 HINT If you want to remain standing at the eyepiece to command the init to verify the star is centered you must first click on Keep Window Up large button on the left after you have roughly centered the star and clickednc in your planetarium program or in the sitech synch Goto window Now finish centering the star use pan or guide modes as required Try to make all the final moves for centering using the same buttons to remove the effects of backlash Now you can command an Offset Init by pressing the ESC key Top left key on the handpad or you can perform a CalStar Init by pressing the RET key the top right key on the handpad If the init window remains up click on OK in the init window 4 8 OFFSET INITS VS CAL STAR INITS 4 8 1 Offset Inits I like to explain an offset init by the analogy of grabbing the sky and moving it unt
140. e for exchange of information on the SiTech System at http www sitechservo info Dave Rowe has contributed some of the most useful software routines and worked with Dan to make the SiTech software really world class Dave s routines are fully and freely integrated into the SiTech software PointXP PlateSolveXP and CalPointsXP are Dave s routines Dave was also instrumental in many other algorithms such as the Gurley IPE corrections Chuck Shaw has beta tested literally all of the SiTech software working with Dan and Dave to make the software work properly without bugs or other problems Next to the software authors Chuck knows more about how the system works and the procedures to use A lot of both manuals was written by Chuck David Thompson in England is an active user of SiTech and has helped work out bugs to make SiTech work smoothly with ACP for automated observatory operation 155 of 236 APPENDICES Appendix A Tick Management The purpose of Tick Management is to use an economical medium resolution encoder to close the loop for your telescope axis which can remove all backlash and periodic error Tick management works like this You must have an encoder on your motor and a medium resolution encoder on each of the telescope axis s on which you want to apply tick management Inside the SiTech servo controller every time a new scope tick happens the motor location is captured When a communication is sent from the ser
141. e information window on a target you just clicked on longer than you need to in order to take action on it The problem is the screen update clock stops while that information window is up So why is this a problem Well lets say you click on a target but then you delay clicking on Center the Scope or worse you delay clicking on Sync the Scope The RA Dec at the time you clicked on the target were captured in the information window but the sky keeps moving ok the earth keeps rotating so when you do get around to clicking on the center or the sync button in the information window it will obediently GOTO or Sync to the coordinates that were valid at the time you initially clicked on the target However the target is not there any more The result is your sync 163 of 236 or your GOTO will not be accurate There is an easy fix however If you have had a delay because you are reading about the target or got distracted simply close the info window and click on the target again and click on your GOTO or Sync Another ECU Funny to occasionally have to deal with is due to the fact ECU is a 16 bit program So to run in a 32 bit environment ECU automatically runs a program in the background called WOW exe The problem is when you close ECU WOW exe does not also automatically close Most times you do not care However if you disconnect and then closed ECU and then changed your mind and re started ECU and tried to re connet to Sitech
142. e mode In this mode the encoders are used when slewing and when initializing but not when tracking Thus there will be no jump if the disagreement reaches the supervisory threshold Please set up the Supervisory Threshold to a value that is GREATER than the resolution of your telescope encoders Lets say you have an 8192 resolution encoder on your telescope This is about 3 arc minutes so you might want to set up your Supervisory threshold to be 4 arc minutes 61 of 236 The Drag Mode is a new word invention of mine it means the tracking of the telescope is totally based on the location in the sky the telescope is at a certain point There is no RA Dec setpoints it s blind tracking actually most telescopes use this exclusively The drag name came from the reason I included this If you have external encoders and clutches then you may want to drag your scope to another part of the sky If there wasn t a drag mode the computer would move the scope back to where it was The drag mode keeps this from happening Later on I thought it may be useful to have a drag mode even if you didn t have external encoders so I turned it from a radio button to a checkbox and it s a feature that can be used anytime NOTE Drag and Track Mode is similar but is used when there is not a computer attached to the controller i e in standalone mode Drag mode is when SitechEXE is being used with the controller Setpoint Definition
143. e pans smoothly change from one pan command to the other or I could end the pan at the proper place and restart it I chose the former so the pans would appear smooth at the eyepiece They are mainly for visual so that s why I chose it This is less accurate because we check to see if the Pan has ended in the PC and you have the comm loop time which allows errors It may detect the pan is finished after it s crossed its end point so in effect the next pan will start from slightly the wrong point So when you are trying this be sure you set up your comm loop time to 50 or 100 mS and turn off and deselect your focuser s in the Config screen so it won t communicate with the 2nd controller Also slow speeds work best and are the most accurate This will make the design on the ccd more accurate Also scope balance backlash can be an issue So I was thinking a really cool tri color rose design or something would make APOD and also be one of the featured photo s in back of skyNTel magazine I also found out that when drawing arcs it s much better to turn them into longer lines The PU and PD commands pen up and pen down are so close together on an arc or circle that the script has to actually move backwards sometimes So I zipped up a flower with 3 different colors Fancy cad and if you view the cad drawing you ll see how the arcs are actually fairly long lines 154 of 236 15 FUTURE PLANS We are planning the following Cre
144. e temperature is averaged during this time so longer times reduce temperature sensor noise Try 60 seconds initially Set the buttons to control the primary scope focuser or the guide scope focuser if present TCF is not available for the guidescope 118 of 236 8 1 3 Temp Compensation Tab f j Telescope Focuser o1 778 Absolute Positon 0 1755 Effective Postion 1521 21 4 Temp Switch sensor Fast Focus IN C Slow Focus our IN JOG OUT Jog Dist 0 0100 HF Jog HP Slow HP Fast Temperature Comp ON Already Focused I Temperature Comp ON Move To Focus ie Add Calculate emperature hral Calibration a Point Temperature i ae Clear All Stars Stars Hide Save Window Presets H Colors uonesuadwoy dwaj ssayaweieg syulodjag The Temp Compensation tab is for calibration of the TCF It should only need to be run once TCF CAN be running assuming you have a rough calibration line while adding additional calibration points Add Temp Calibration Point does just that Add as many as practical up to 100 over as wide a temperature range as possible Of course the scope must be focused when a point is added and the same eyepiece or camera must be used for each calibration point Calculate Calibration Line fits the best line to the data The data are shown in the gray plot area The plot is zoomed in around the data so the lower left corner is NOT 0 0 The most re
145. e to SiTech you need to disconnect the PC cable from the SiTech RS 232 port and It is a good idea to have both the SiTech controller and the Sky Commander turned off when connecting and disconnecting the RS 232 cables The cable diagram to connect the two units is shown in Appendix E in the SETUP Manual 25 of 236 2 5 2 Setting up SiTech for Sky Commander This section addresses only the ServoConfig settings specific to using the Sky Commander with the SiTech controller First connect your SiTech controller to your PC via the supplied DB 9 to RS 232 cable Launch the ServoConfig exe program Press the Edit Parameters button on the left panel When prompted you will likely want to get the settings from the SiTech controller or possibly a configuration file if you have created one earlier At this point it is assumed that you have already configured your controller with motor and encoder info and confirmed that the SiTech servo motors and encoders move in the proper directions using the hand pad buttons Follow the instructions in Section 2 1 1 Setting Up the Drag and Track Mode for Alt Az mounts Follow the instructions in Section 4 13 EQUATORIAL AND GEM INVERT BUTTON SETUP for GEM and Equatorial mounts Setting Up SiTech for Sky Commander with Alt Az Mounts The Configuring Sidereal Technology Servo Controller window has 3 tabs Motors Encoders Auto Tracking and Misc and Action Select the 2nd tab Auto Tracking In this
146. e to binary response The first byte is 101010nn nn is the address of the controller 236 of 236
147. econd controller and a motorized focuser and or rotator is beyond the basic setup the details on these capabilities are in the Advanced Features Section 70 of 236 4 11 7 Setup Potentiometers Tab ADVANCED FEATURE Setup Silech ASCOM Driver V0 54L Telescope Info Mount Info Scope Encoders Miscellaneous Ascom and Troubleshooting Focuser Rotator Potentiometers Reverse Supervise R Az l Reverse Supervise Dec Alt T Use Supervisory Pot RA Az Supervisory Window RA Az Use Supervisory Pot Dec Alt J Supervisory Window Dec Al OK Cancel Help Telescope Mount encoders are digital devices that are intended to be read out by digital interface hardware However sometimes it s possible for all those digits to get messed up This is especially important when using a system via remote control So the ability to use an analog device a potentiometer was added The idea is to mount it like a normal encoder would be mounted and the controller simply sends a voltage out to the pot and measures the resistance reading which varies as the pot is rotated by the telescope axis The accuracy is not great but its plenty accurate to have a reasonably close measurement of the position of the mount after you calibrate the pots use the procedure for this in ServoConfig exe The instructions and the schematics for how to wire this up and a recommendation for what pots to use are in the SETUP Manual and its appendices
148. ed Once the unit is in configuration mode there are 11 settings that can be changed The first parameter lets you choose between 4 different setups presumably for using the Sky Commander with 4 different scopes Select the desired configuration number and hit enter There will be a confirmation message that this has been saved to EPROM so it will take effect the unit is turned back on I believe that you need to press enter after changing each value for the values to take affect when the unit is turned back on 1 Select Setup D 1 2 3 4 Press the down arrow to get to the next and all subsequent configurable items Note the current setting is capitalized sometimes completely sometimes just first letter 2 Scope Mount 2 lt fork DOB germn gt 3 Set Hemisphere 3 North south This parameter is scope installation dependent I do not think this is used when the encoder info comes from SiTech controller over the RS 232 cable encoders connected to SiTech controller If you confirmed the SiTech direction of encoders and motion as earlier directed then set this to NORM 4 RA Direction 4 NORM rev This parameter is scope installation dependent I do not think this is used when the encoder info comes from SiTech controller over the RS 232 cable encoders connected to SiTech controller If you confirmed the SiTech direction of encoders and motion as earlier directed then set this to NORM 5 Dec Direction 5 NORM
149. ed for screen space it might be best to let it automatically close e However the graphic shows the current Alt Az of the scope and the cursor on the graphic shows the current position which is VERY handy for monitoring the progress of script 6 When ready for the Really Big Show click on PLAY Click on the SCOPE tab in the Sitech window to be able to watch the PointXP Stars Stars Loaded counter increment The counter will already show the 2 or 3 initial cal stars you did and will increase from there The script will slew the scope to each of the points calculated by CalPointsXP then after the slew will settle for the time you selected Then the script will take an image using the camera s w and save it in the Sitech folder as Default fit Then the script calls up PlateSolveXP and PSXP solves the image for the RA Dec and sends that back to Sitech Check the Use Sitech Init Window in the script window if you want to watch the init window in Sitech useful to intervene to only do Load Stars Calc Terms if all you are doing is updating the polar alignment measurement Sitech then performs a Cal Star Load Init and the PointXP Stars Loaded counter on the Sitech Scope Tab increments If a solution is not quickly found PlatesolveXP will search 999 default value FOVs around tgt Alt Az the script will move on to the next star and then the whole process repeats till it has slewed to each of the init points in the script
150. elScale The x directed pixel to pixel spacing in arcseconds Angle The rotation angle between the image and the catalog in degrees Stretch The scale factor between the y axis and the x axis Skew The normalized image skew from the complete Affine transformation Num The number of stars extracted from the image 206 of 236 The third line in the file is the textual status of the search as given by the above return codes The PlateSolveXP Catalog PlateSolveXP requires that its catalog be placed in the following directory C Program Files Starry Ridge APM There are 4502 files in this catalog containing approximately 667 MB of data Each star entry is 10 bytes so this catalog contains position and magnitude information for approximately 66 7 million stars Running PlateSolveXP as a Windows Application When PlateSolveXP is started without command line parameters it is a normal MS Windows application On startup you ll see two windows The window to the left is the Parameter form and the window to the right is the Display form 1 Load an image into the Display form using the File icon or the File pulldown menu The image format must be JPEG BMP monochrome FITS 8 or 16 bit or SBIG 2 In the Parameter form enter the approximate J2000 0 image center in the RA and Dec text boxes The format for RA is HH MM SS or HH MM SS or DD D The format for declination is DD MM SS or DD DDD where D is degrees M is minutes S is seconds a
151. ely slow I think I fixed the oscillation when backlash is on at slow speeds 054J No I Working at RoweVille Took off the test button made invisible from the main SiTech Window Logging the TDiff in PulseGuideMethod If Pulse Guide duration is zero we stop any guiding in progress Taki Timer runs in force mode if bad checksum This is an experiment Re ordered something in GetOffsetTrack for more logical operation Looking for file instead of program exit on PlateSolveXP 054H Put back the old Thread Sleep msecs routine instead of my new one that might not be working right Worked extensively on the southern hemisphere bug 054G Fixed the PhotoInit so binning works delay for the save script starts after the exposure time photo init OS4F Fixed the Photolnit so it hardly ever hogs the system 054E Worked on AArt Camera stuff again This worked 054D Fixed bug with two controllers Made the camera FOV Calculator parameters sticky Worked on the AArt Camera stuff 054C Hopefully fixed the Photolnit button Made FOV and RA Dec come from Config Tak instead of fits file Can Bin up to 6 054B 213 of 236 Nothing I guess 054A Added checkbox for doing SiTech Inits in the auto mapping scripting screen Added button for doing a SiTech init and plate solve scripting screen EEEE K E K K K K K K K K K K K K K K K K K K K K K K K K K K K 0 53A Made Drag mode use pointxp
152. emPro and process the data according to the help files in PemPro and save the PEC curve Verify there are no Collective Items in the Collective in case you were messing with PEC earlier In the middle column it should say You have 0 in Collective If there is something in the Collective click on the Clear Collective button in the middle column Just to make sure click on the Show 5 Collective Items on the right The Pink line should be flat Now finally in SiTech exe s PEC graph display down in the lower right corner click on Load PemPro File Select the ppc file you just saved and it will load If you have file buffer checked it will also show up on the graphic area and an orange dotted line Verify it looks like the plot in PemPro If not you may have to invert the file in PemPro and re save it then re load the file into Sitechexe again Then in the middle click on Load Collective item from file buffer Then make sure the averaged buffer is checked and you should have a nice smoothed PEC curve that you can then load into the controller using the Send averaged Table Buffer to Controller button on the left And after its uploaded click on Save controller Ram to flash Make sure that the data in the controller matches what was sent to it by clicking on the Read Controller PEC table into the Controller Buffer and then make sure the Show Latest from Controller is checked on the right
153. emperature Longer times average the temperature reading over longer periods so can reduce temperature sensor noise eke Click SAVE PRESETS to save your presets 120 of 236 8 2 5 To Set the Setpoints Setpoints can be used to memorize the focus positions of different eyepieces cameras and filter combinations Setpoints must be set with TCF OFF The absolute position of a setpoint is not nearly as critical as the relative position between setpoints The absolute focus position for an eyepiece camera E C depends on the temperature However the distance between focal points for different E C s remains virtually constant Therefore while setting the setpoints it is most important that the relative distance between each E C is as accurate as possible 1 Right click each setpoint button to give it a meaningful name By using the four setpoint groups you can save up to twenty setpoints 2 Confirm that TCF is OFF 3 Zero the focuser 4 Putin E C 1 and focus It is best if this is the E C that you normally start the evening with Click the M button to the right of this setpoint to memorize this position 5 Put in E C 2 and focus using either the window buttons or the handpad 6 Click the M button to the right of this setpoint to memorize its position 7 Put E C 1 back into the focuser and left click setpoint 1 The focuser should move to the focal point for this E C 8 Confirm that temperature changes have not defocuse
154. end of the actual mount axis shaft being measured or is attached via a perfectly symetrical coupler to the end of the mount s axis shaft There can be no slippage with this and the axis of the gurley must run perfectly true with the axis of the mount However if you couple the gurley to the mount axis with a cog belt or with spur gears or with a roller drive any tiny errors in this connection will be added to the actual mount axis motion and the gurley has absolutely no way to know that is happening since it thinks it is directly coupled to the mount s shaft Another way to look at this is to assume that if the Mount shaft is actually turning at a perfectly smooth sidereal rate then the errors the spur gears introduce will be what the gurely actually sees and the software in sitechexe will think the RA shaft is NOT moving smoothly and will correct for that not smooth motion The result will be the RA shaft s smooth motion would be ruined by correcting for the spur gear errors An autoguider does not get affected that way It just simply watches the guidestar and sends commands to make the RA shaft match the sidereal rate in the sky However just like with imperfect spur gears for the gurley if a guidescope is not perfectly ridgidly attached to the main scope OTA you will get smeared stars due to differential flex So in a way you can think of bad spur gears for the gurley coupling as differential flex for the encoder So botto
155. er than Iam Well in the summer of 2007 I attended a workshop on doing science with small telescopes http www orionobservatory org Word 20Files STAR 20W orkshop pdf I gained a new friend at this workshop David Rowe After Dave saw what I was doing with SiTech he was pretty interested also appreciative of all the work that went into it So he causually mentioned I ve got a telescope mount modeling program would you like to incorporate it Well I said yes He said well it will take me a couple of months to go through the source and make sure it s documented etc but we ll be in contact about this I took a deep breath and was wondering if it was vaporware Well it wasn t true to his word Dave emailed me the source code which is in visual basic I went through all his source line by line and converted it to C After getting out the bugs I introduced it worked I was thrilled So after much testing adding to the user interface etc I ve finally been able to release this Please email a note of appreciation to David Rowe if you are so inclined He is a member of the SiTech users group 5 1 2 Aligning PointXP Using PlateSolveXP PlateSolveXP is a stand alone program written by Dave Rowe that extracts star centroids from an image and matches the extracted information to a large database of stars complied from several catalogs The user must enter the approximate center coordinates and the field of view of the image Pla
156. ere is no communication with the primary controller at addr 1 this message is displayed Check to see if the controller is powered on and the RS232 plug is connected and the RS232 plug and USB dongle if used is also connected to the PC Tracking Displayed while the telescope is tracking Slewing Displayed while the telescope is slewing Scope Parked 37 of 236 Displayed if the scope is parked Stopped Displayed if the scope is stopped Move By HandPad If the Telescope Handpad or Auto guider is giving inputs to the SiTech Controller you will see this message 4 2 3 RA SHA Dec windows Just below the message window is an area that has three windows The top one shows the Right Ascension that the telescope is currently aimed at If the mount is tracking this value will not be changing since it is tracking that RA location If tracking is OFF this value will constantly be changing as the RA of the sky the scope is aimed at rolls by The middle window is the Scope Hour Angle This is static when the scope is not tracking and is changing if the scope is tracking as you would expect The bottom one is the Declination that the telescope is aimed at To the left of these windows a vertical button labeled Hide provides the ability to shrink the SiTech window down to something the size of the button and have that button remain docked to the upper right side of the screen Some folks like this better than the alternative sh
157. ermisson Teams to Inchade in Model Term 0 00 03 30 Termf1 00 00 53 Cone Z2 00 05 32 ee Term 2 00 00 00 Term 3 00 00 00 HIj 00 01 49 Dec Imbalance 00 02 38 7 RA imbalance 00 04 00 Dec Transverse 00 07 31 W RA Transverse 00 00 12 Dec Dicop cos 00 09 50 7 Dec Droop sn 00 05 14 Al Sin 2 Phil 00 10 23 Al Cos 2 Phi 00 00 00 AR Sin 3 Phi 00 00 26 Ak Cos 3 Phi 00 0542 AltEncO 359 59 59 42EncO00 00 02 Daybght Saves Read Conhig Write Contig Fake Cea Tems AndCalStars Cisa Stars Leave Teems Losd CalStat File with terms Display Cal Stars Enos Toggle Update Display Load CaSta Fie No Tems SaveCaStarFie __WiteDoteldebug Polar Anis Alignmert Enot Pointing Eror 31 Stars mn modell Ponting Errot Al 32 Stars Move Down 00 00 44 RMS 00 02 05 RMS 00 07 09 Move Right 00 06 18 Peak 00 05 21 Peok 00 38 45 Calculate Terme Calcudate Offsets Only You can tell a lot about what is causing the mount errors by inspecting the error graph The data plotted above shows there are very small errors left to right in RA and most significant errors are up and down in Dec The most likely source of the errors in this example are from Dec backlash To help avoid Dec backlash errors always make your final approach to the CalStar using the same button on the handpad either up or down The Scripted PlateSolve technique avoids these Dec backlash errors since the mount drives to the location in
158. erms Load CalStar File with terms _ Save CalStar File __Errors Toggle Load CalStar File No Terms Display Cal Stars WriteData debug m Zenith Axis Alignment Eror p Pointing Error 16 Stars in model l Move Down 00 27 58 RMS 00 01 21 Move Left 00 25 45 Peak 00 02 46 Calculate Terms Calculate Offsets Only Okay Help Me 74 of 236 About the PointXP User Interface The left side of the PointXP screen holds the telescope Error Terms You can see a checkbox and also the current value of the error term If the error term is enabled but the value is zero then probably the error term is blocked by the number of calibration stars included in the model In other words for all of the terms to be enabled at least 16 cal stars have to be included Below this are buttons for various purposes Read Config Reads the previously saved Telescope Erorr Terms from the SiTech cfg file Write Config Writes the current telescope Erorr Terms to the SiTech cfg file Clear Terms and Cal Stars Clears all terms and Cal Stars from the PointXP model Clear Stars but Leave Terms This will leave the error terms Below these buttons are the current Polar or zenith Aligment Errorrs If you are using an equatorial telescope this will tell you how far to move your mount to get it polar aligned What are the mount error terms 1 Cone Z2 This is a fabrication error It is sometimes called Collimation error as it is th
159. es are called Two Line Elements TLE s You have two choices The SPACETRACK website probably the best quality data at http www space track org perl home pl or you can download from Celestrack at http celestrak com You will need to register at SPACETRACK to be able to download the TLE data from there Costs nothing and is highly recommended The accuracy of TLE s degrades quickly so be sure to download the latest files just before your observing session You also need to have the time in your PC set as accurately as possible to 1 second accuracy or less Windows can do this or you can use a program like ATOMIC CLOCK SYNC from http www worldtimeserver com atomic clock SitechEXE also will need to be configured if you have an alt az scope In the Config ASCOM and Troubleshooting Tab place a check in the box ASCOM AxisRates to R A and Dec B Setup SiTech ASCOM Driver V0 54L Telescope Info Mount Info Scope Encoders Miscellaneous Ascom and Troubleshooting Focuser Rotator Potentiometers Log Serial Communications I Log ASCOM T ASCOM AxisRates to R A and Dec J Log Debug Stuff I Slew Settling Time 0 Priority Above Normal Priority High 7 Instant Total Pulse Guiding sPulseGuiding Always returns false Log Gurley Interpolation I Invert Gurley Interpolation Ok Cancel Help 149 of 236 Sat Tracker s layout is easy to learn after you play with it for a while You can
160. et you to the starting point if you are not already there since the Anchor command does not use the co ordinates as you are building the script When you click on Add Anchor it uses the co ordinates when the script is actually executed IMPORTANT Before you run the script be sure the telescope is pointed at the exact location you want to start the script If you don t the script will be relative from wherever the telescope is pointed at the time the script is started Here s an example of a Pan script that Pans the Veil Nebula You should have a wav file named Veil wav in the SiTech folder for the Sound command to work If the file is not found it simply skips over the script line Slew 20 47 10 30 14 00 0 06 Sound C Program Files Common Files ASCOM Telescope SiTech Veil wav Prompt Press OK to start panning the Veil Nebula Pan 20 46 30 30 33 03 0 06 Pan 20 46 15 30 44 25 0 Pan 20 46 05 30 58 32 Pan 20 45 55 5 31 15 13 Pan 20 49 01 31 08 58 0 2 Pan 20 48 25 31 46 11 06 Pan 20 48 37 31 58 49 Pan 20 54 58 31 58 03 2 Pan 20 56 40 31 42 09 06 Pan 20 57 28 31 24 01 Pan 20 57 17 31 11 06 Pan 20 56 28 31 03 21 Loop 5 2 4 Using the Handpad to control a Script To pause the script you can press the Top Right Button RTN To Unpause press it again 94 of 236 When the Prompt or the Pause command is in use pressing the Top Right button RTN will make the script continue When a count dow
161. ffset tracking rates appear You can enter these tracking rates into the two text boxes or use the sliders and your scope will now track the solar system object You can type in an offset rate of up to 10 arc seconds per second but the sliders only move to One arc second per second The Offset tracking rates are applied to RA Dec even if you have an Alt Az telescope One thing to keep in mind that many planetarium programs use different Engineering Units for 103 of 236 the Offset Tracking Rates for instance TheSky uses Arc Seconds per Second of Time same as the SiTech Telescope Driver but Earth Centered Universe uses Arc Seconds Per Minute of time so you would have to divide the ECU values by 60 for the SiTech Driver to track properly HE RateAdjust mM If you Don t use the DRAG mode N fo Offset Tracking Rates Mins Drifted 2 Are Secs Calculate Arc Seconds Per Second Works on Alt 42 scopes with RA Dec too Declination Rate To Zero IN fio Dismiss Mins Drifted HELP ME Right Ascension f Ate Secs SPOCK Calculate Colors Rate To Zero p If you use the DRAG mode Tracking Calibration Rate To Nominal Mi LIUITIIEITE TT ITEITETIT TTT TIT TIETEET TETIT TTET TEITTE ETETETT TETTETETT TIETEET ETETETT Servo Cal to Servo Clock Calibration fi 1 0 Recommended ServoClock Ratio 0 08 Re Sync Save ServoCal Cool Feature Drift Calculator So if
162. ffsets and the alt az offsets Ok to use Polaris for an Alt Az mount but not anything at the zenith e Next star 3 one has to have signigicant movement in altitude because the cone error is added as another term after the 3 star If you went UP for the 3 star then go DOWN 20 30 deg for your 4 star because the hub term is added after the 4 star After this look at the all sky plot in the PointXP screen and just fill in the empty places You can do this by simply clicking in an empty space on the plot the All Sky Plot toggles between the error plot and the all sky plot with the button below the plot Then do a GOTO to a nearby identifyable star for the init e You need to get at least 16 stars to have enough to calculate all the terms You should take a few more in case you need to delete some from the Cal Star file if you have any with large errors during the editing of the results e If you do not want the full 16 then 6 well placed stars will have a HUGE effect on accuracy Probably a lot more than the increase from the remaining 10 stars e A ring of stars at the same altitude will make the hub and cone terms blow up Hub and cone are probably the two most important terms and in order for PointXP to calculate them it needs a lot of data at different altitudes e Accuracy for all other terms is also affected by separation Do not cluster all your points in one area of the sky even if all the altitudes are covered or accuracy will
163. file C Program Files Common Files ASCOM Telescope SiTech LXToSiTech cfg with notepad Find the line that has the comm port and change the number to an unused comm port 6C Now run the LXToSiTech exe again it should all work this time 7 Now run your planetarium software Specify LX200 and then be sure to select the proper comm port 8 Connect your planetarium or SatTracker software Everything should work 143 of 236 11 2 LX200 COMMANDS IMPLEMENTED Focuser commands F Move toward primary at selected speed F Move away from primary at selected speed F lt n gt Set Speed FF Set Fast Speed FS Set Slow Speed FB IsBusy FPsDDDD Position relative Fp Get focuser position FQ Stop focuser motion CA Sync to alt az CM Sync To Ra Dec U Toggles Hi Precision Co ordinates GR GetRA GD Get Dec GA GetAlt GZ Get Az hP Park hS SetPark hW UnPark Q all Q s simply stop SrTNN NN N Set RightAscension SdNN NN Set Declination SaNNN N Set Azimuth SZSNNN N Set Altitude RC Rate to Center Rate RG Rate To Guide Rate RM Rate To Find Rate RS Rate To Slew Rate RANNN N RA Az rate RENNN N DeAlt rate RENNN N Guide Rate MS Slew To Coordinates MA Slew To Alt Az Mn Move North Ms Move South Me Move East Mw Move West MgnNNNN Guide North MgsNNNN Guide South MgeNNNN Guide East MgwNNNN Guide Wes 144 of 236 12 NON SIDEREAL TRACKING
164. flat cable will be the same type but you will also need to connect a ground wire from the connector labeled Ground to the Ground of the Stepper board You must also be sure the internal jumper inside the receiver is set to the side labeled Stepper instead of the side labeled Servo 10 4 3 Transmitter LED s The transmitter has 4 LED s on the front which mainly operate as a flashlight If the transmitter is used as a wired handpad and there is no battery only two of the LED s work because there is not enough voltage from the 5 volts to operate the 4 LED s in series If the power is on and the flashlight is off the 4 LED s will be on very faintly This is the only indication that the power is on If the flashlight is off whenever a transmit burst happens the LED s flicker This is an indication of the radio transmission If you are using the handpad in the wired mode the radio transmitter is disabled but the flicker is still visible If you press a button you will see the initial transmission and when you release the button you can see the release transmission If you press and hold a button you can see the initial transmission then every second there will be another transmission as the receiver expects a transmission every second to assume the button is still pressed 10 4 4 Receiver LED s There are 4 LED s on the receiver Three LED s on the receiver are for indicating the current handpad speed of the syste
165. fly Made system come up even if there is a bad comm port Start Minimized after a short delay Made 10 lines available instead of max of 5 PEC lines in the collective Made AdjustAngles window Modal Fixed false accept ticks per rev window when focuser enabled Tracking and parked at the same time fixed Made unpark be available anytime with prompt no prompt if already parked EEEE E E 28 E K E K K E K 2g K K E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2 K K 0 39 Fixed focuser moved from SiTechExe to SiTech so ASCOM could communicate Fixed read EEEE E E E K E K K E K E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K 0 38 Made the SiTechExe exe and SiTech dll separate files Many SiTech dll instances and only one SiTechExe instance Now many things can control the telescope This took over a week to do a lot of work Found bug if your computer was on a really long time then the environment ticks would roll over to a negative number which blocked the timer routine in ServoComm FAS FAS 2g 2g 2g KE 2g E K E FAS K E K K E 2g K K K K K K K K K K 28 K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K FK K K K K 2 K K 0 37 222 of 236 1 Make a better solution for the ascom track before initialized if alt az we init and track tracking may be wrong if equatorial if below horizon or raw dec
166. for better tracking accuracy Made read keypad ascom command by using CommandString method If using version 3 4 or later of controller firmware it uses a standard rate then an offset rate for so much time This make tracking better if there is a communication error todo Controller make a command to ignore bin2bytesexpected on YXR make sure guide mode still works after all this without messing up xbits 053B Fixed reading PemPro file bug Using scope tix instead of motor tix 053C Made CommandString return the worm phase if received a PECIDX Made PEC Window modal Made Tracking Rate Window modal 053D New feature Keypad Slip Fixed meridian crossing bug 053E Made the M Flip reverse the keypad directions with one long string instead of 3 separate strings This prevents the scope from stopping at the pole if there is a focuser O53F Some scripting components working on camera control 053FJ Version for juan that doesn t reverse the guide mode 053g Put reversing guide mode back in and fixed jumping 053G Blocked the ascom guide function if Taki Timer forced Hopefully prevents jumping while pulse guide is used 214 of 236 Inverted pempro file reads fixed pempro file reads for shorter files 053H not done yet Fixed Synch returning right away so acp continuted with script b4 synch was finished 053J no 53 Working on getting the scripting to do an unmanned pointXP run Made the commtime be me
167. for the Help menu and is a convenient reminder of the following information Scope Latitude If you have an alt az scope or are doing Multiple Star Inits with an equatorial scope then pay attention to this number It s also on the Initialization window Before you add the second star this number is your latitude if you have an alt az scope or 90 degs if you have an equatorial scope When you add the 2nd star this number is updated based on the calculated matrix math by the initialization engine It should be close to your latitude if your scope is level and you ve an alt az scope or should be close to 90 deg s if you have an equatorial scope If this number moves very far from where it should be then you ve an initialization problem which should be corrected Depending on your mount and your init points this will hopefully be less than 30 arc minutes Scope Longitude If you have an alt az scope or are doing Multiple Star Inits with an equatorial scope then this number is updated once you add the 2nd or later star It s also on the Initialization window Before you add the second star this number is your longitude When you add the 2nd star this number is updated based on the calculated matrix math by the initialization engine Don t pay too much attention to the longitude if you have an equatorial scope The math blows up so it s never accurate if you ve an equatorial scope The latitude and longitude can be useful if you ve an ac
168. for the telescope the Rotator position is also remembered Now when you click on Park it will return to this position If you click on Unpark it will initialize 128 of 236 itself for the parked position 9 2 2 Initializing the Rotator To initialize the rotator set it at the zero position and then click on the button labeled Zero the Rotator OR set the rotator to the parallactic angle and click on Init Rotator To Par Angle The top text window is the current rotator position The number is based on your Ticks Per Revolution specified using ServoConfig The next text window is the current Parallactic Angle This should remain close zero for equatorial telescopes The next text window is the current Parallactic Rate This is how fast the rotator moves when tracking This should remain close zero for equatorial telescopes It will be zero unless you add two or more stars to your initialization then it may track very slowly to compensate for you telescope misalignment If the red button between the CCW and CW labels is shown there is no communication between the computer and the 2nd controller The next layer of buttons is the Fast jog buttons CCW or CW The next layer of buttons is the Slow jog buttons CCW or CW The next layer of buttons allows you to use the telescope handpad as a rotator adjustment If you click on the Slow button pressing the top left and the top right buttons will rotate CCW and CW slow If you clic
169. g Put testing information in the goto on click the azimuth display Re arranged some configuration things for pointxp 050J Added a lot to the PXP screen mostly buttons Fixed inits after init screen with topleft and right buttons 050K and L I forgot Probably various small stuff 050M Made the Init window be a permanent window that is just visible or invisible 050N Fixed synch bug ignoring nutation and aberration created in earlier 050M 050P Possibly fixed the pulse guide bug duration of 0 Found funny bug where the scope would track but the timer routine in takitimer wouldn t read the scope position so things went crazy Hopefully fixed Added scope position to the pointxp sky display Made PXP Win come back up when clicking on pointxp button even if minimized 218 of 236 Did same for focus and rotate windows made focuser and rotator move buttons be click on then off when released Made the controller altitude be updated if a change of altitude is gt 10 0 050Q Make Pointxp clear all terms when loading the Ist star Make pointxp recalc when changing star data OSOR Added AzErrorGain and AlErrorGain to config Fixed some cosmetics Make loading up an alt az config with an equatorial pxp file provide warning 050S Made gain lower for tracking gain Fixed reading and applying motor scope offsets when starting up Possibly fixed the crashing bug when SiTech crashes when ECU AND Maxim c
170. g in calculating the latitude and azimuth if south of equator 2 DONE optimize routines for speed 3 DONE Add Backlash 4 DONE XX W Backlash Rate command added 5 DONE add local search 6 DONE Added the XX X command which makes an offset for the altitude 7 DONE if backlash is too big set to zero in case upgrade from version 1 5 or earlier 8 DONE Make the 1 Cos Alt happen only if configured for dNt or if updated by computer 9 DONE now that we can know the altitude expand the azimuth Pan and Guide rates 310 DONE Add XX Y command to set and read the azimuth 311 DONE Test high speed two at once Max is 6 500 000 while both running 312 DONE Make local search work both ways 313 DONE Make local search pause feature 314 DONE Make drop out of argonavis mode if detect cr alone 315 DONE if in search mode don t save the ramps 316 DONE Fix Local Search being locked out by other move commands 317 DONE Make Binary Protocol recognize other addresses but not act on them 318 DONE Lock Out Local Search if not address 1 319 DONE Test all commands Test High Speed with Communication Scopell and Binary 20 DONE Test using two controllers 321 DONE Send XandYBits via picServo 322 DONE Make local search work with argonavis 323 DONE Lock out PicServo mode if binary mode started 324 DONE Default Integral 2500 from 3000 325 DONE Any Key cancels the
171. g is 250 ms This will have SitechEXE communicating with the controller 4 times per second If you are using SitechEXE routines that benefit from more frequent contact with the controller like Gurley IPE the fastest comm loop time is 50ms 20 times second as of SitechEXE version 054L If you use two controllers on a Y cable one for the mount and one for focusers for example the actual achieved comm loop time is double this setting You can observe the actual comm loop delay the system is operating at on the Numbers Tab commdif You can use any setting as long as it is 50ms or greater There are a number of Voice status reports Slew ended Offset Init Cal Star Init etc Most users find them handy but if you do not want to hear them click on Mute Sitech Sounds It s important to know if your planetarium software sends fully cooked co ordinates or not By Fully Cooked we mean precession nutation and aberration of light have been corrected before SiTechExe receives the co ordinates All planetarium software precesses the co ordinates to the 66 of 236 current date however most don t correct for Nutation or Aberration This can make a large difference if you are trying to do telescope modeling with PointXP If you don t know for sure ask technical support for your planetarium software I know of only one that sends fully cooked coordinates TheSky So if you are using TheSky then turn Nutate and Aberrate Coords OFF To improve the
172. gd Wig e SUN MOYS p ang ajonuog woy way aAnoayog peog TH JaONUOD Ul alge 734 a3 w Oz BANISYOT G MOYS aAnaayO7 139 _ suds 93d any asn L spuosas ay gz dwg smes yng nug Bt 0 IP S 3d yde19J d fa 177 of 236 Appendix E Sidereal Technology Servo Controller ASCII Command Set Notes 1 All commands MUST BE IN ALL CAPS Both ServoConfig terminal and also the Terminal in The SiTech Telescope driver ToUpper the commands for you 2 The character represents a decimal number that you must type 3 After each command press the ENTER key 4 All Altitude commands begin with an X All Azimuth RA commands begin with a Y Q No cr after Send scope encoder data in Tangent format SB Set Baud Rate 1 9600 2 19200 Changes all controllers on serial bus 1 5 or later X Move Servo 2147483648 to 2147483647 You can tag a speed command at the end Example X 2345S 1000000 lt E gt X Returns the X position of the servo XF Forces the X position to be equal to the number 2147483648 to 2147483647 This stops the controller if moving XS Velocity of X Servo 0 2147483647 XS Returns the X velocity of the servo what it would be if it was currently moving at fully accelerated speed this may not be what it acually is at the moment XR Ramping speed or Acceleration of X servo 0 3900 XR Returns the Ramp speed XP Proportional Band of X servo 0 32767 XP Returns the Proportional band XI X Integral 0 32767
173. ger No resonant frequency s to battle Motors will never miss steps Many times stepper motors will simply stop instead of turning during slewing The computer controlling the stepper motors will lose its position information when this happens 13 of 236 A real time operating system is in the Servo Controller itself thus making a real time operating system unnecessary for the controlling computer some stepper systems have this too This means the same computer can operate your telescope with a planetarium software interface while still tracking perform imaging autoguiding the telescope controlling a dome etc all at the same time using the same computer This can be a significant cost savings of a servo system over a stepper system evening the cost savings of a stepper over a servo system Much smaller size in the case of the SiTech controller anyway If only simple tracking is desired no external computer is necessary SiTech feature If no external computer is desired but GoTo s are the SiTech Controller can be controlled by an Argo Navis a Palm computer a Windows Mobile PDA or a Sky Commander The stepper system has only one advantage over the servo system that we can think of Cost although a servo system can be less than four or five hundred dollars including controller using surplus motors and software if you do most of the work yourself Although cost is an advantage of the Mel Bartels DOS based Stepper
174. gure the SiTech controller to work with the Sky Commander Solution Using ServoConfig you need to be sure of the following You need to set the altitude and azimuth encoder settings in Sky Commander to 18 000 The SiTech servo encoders should be set for the proper ticks per revolution for the drive gear ratios The sky Commander will get the encoder data from SiTech through the serial cable The mount encoders normally used with Sky Commander should be connected to the SiTech controller In the ServoConfig configuration be sure that the Ignore Encoders is NOT checked You can select DragNTrack mode so it will track on power up if you point to the North Celestial Pole Also after rebooting the controller be sure that the up button moves the scope up and the right button moves the scope to the right Then be sure on the Misc and Action tab that it s set up for a Sky Commander To sync on a star you don t press the top two buttons Pressing the top two buttons initiates communication and or does a GoTo To sync on a star you make sure the star is centered and then you use the SkyCommander to do the sync Obviously you have to have the communication working before you perform a sync Be sure the internal sidereal clock in the Sky Commander is ON Interface Troubleshooting with other Programs Problem I can t get ACP up and running for the SiTech system When the SciTech scope mount is selected in ACP it attempts to load the SciTech installer
175. h TM and IPE running That is not the same as sub arc second accuracy Tracking means movement at some rate TM and IPE keep the tracking rate close to constant and close to the Earth s rotation With the Gurley the effectiveness of using an autoguider is improved since the amount of guider corrections is reduced Since Don shoots CCD images that are almost always 10 to 20 minutes each He has said he has no hope or plans to image unguided Don s SiTech mount is an older AP1200 non GoTo made in 1996 It has a native periodic error about 57 arc sec peak to peak that is smooth enough for an autoguider to control to sub arc sec error Using PemPro with 10 cycles recorded and applied to SiTech his tracking is about 14 arc sec peak to peak Using the Gurley with TM IPE he gets tracking to about 0 76 arc sec peak to peak on the errors he is able to measure But the other errors mentioned above are still there Then there s seeing seismic human bumbling and a host of other errors that come into play that there s no hope of the Gurley and TM or any other system being able to handle alone 113 of 236 8 SiTech ASCOM DRIVER FOCUSER The SiTech Focuser is an ASCOM compliant focuser so may be used with MaximDL AstroArt and CCDSoft or any other focus software that is ASCOM compliant To get a SiTech focuser you need to have a second SiTech Servo Controller You can control a rotator with the other channel if desired You need a Y RS232 com
176. h varies as the pot is rotated by the telescope axis The accuracy is not great but its plenty accurate to have a reasonably close measurement of the position of the mount after you calibrate the pots use the procedure for this in ServoConfig exe The instructions and the schematics for how to wire this up and a recommendation for what pots to use are in the SETUP Manual and its appendices This tabbed page provides the ability to enable the use of these Supervisory Pots and once calibrated to provide limits and if the polarity is backwards allows you to correct that If you have a remotely controlled telescope it may be advisable to use Supervisory Potentiometers on both of your axes This can help shut your telescope down if things go bad and also the potentiometers act as low resolution absolute encoders that can initialize your telescope to within 1 or 2 degrees There are several things in the Configuration File that you need to set up before you can use the 106 of 236 potentiometers There is a diagram that shows how to connect these pots in the appendices of the SETUP manual Most of the configuration for these potentiometers is done by editing your SiTech cfg file which is in the SiTech folder C Program Files Common Files ASCOM Telescope SiTech SiTech cfg Use an ascii text editor like notepad or EditLite Here are the parameters and descriptions AlPotVolts 5 02 You can measure this voltage from Pin 4 t
177. hat the correct setpoint is If you do not have an absolute zero init sensor or if you do but TCF is OFF these buttons also use the current temperature to reset the absolute true position of the focuser Save Presets saves all the focuser setpoints and focuser parameters in the file Focuser cfg in the SiTech directory Hide window does just that Find it minimized on the taskbar at the bottom of the PC s screen must save them to the focuser configuration file or they will be lost when you close the focuser Click this button to save them H brings up the help file with some of the more important info to remember Colors works like the other color buttons in the SitechEXE pages to customize the colors to your personal preferences If you click on the X in the upper right you will get a cute reminder that once the Focuser routine has been started it cannot be closed until SitechEXE is closed It is very much a National Secret why it must work this way so please do not ask It s really better not to know 116 of 236 8 1 2 Parameters Tab The Parameters tab has general setup parameters and access to the setup window The Setup Dialog button will bring up the Focusersetup window and MUST be used the first time after adding an absolute zero position sensor x E i Telescope Focuser amp 0 1 774 Absolute Position 0 1755 Effective Position TERNA Temp Switch sensor Fast Focus
178. he Handpad Off 10 5 DragNTrack AND SlewNTrack HandPad OPS ALT AZ SCOPES ONLY 10 5 1 Tracking Control 10 5 2 Initializing 10 5 3 Entering and Leaving the Guide Mode 10 6 EQUATORIAL MODE HANDPAD OPERATION 10 6 1 Tracking Control 10 6 2 Entering and Leaving the Guide Mode 10 6 3To Leave the Guide Mode 10 6 4 To Increase the Tracking rate 10 6 5 To Decrease the Tracking rate 10 6 6 Platform Rewind 10 7 USING THE RADIO HANDPAD WITH THE SITECH ASCOM DRIVER 10 8 MEL BARTELS STEPPER SYSTEM OPERATION USING SCOPE EXE 10 9 ARGO NAVIS amp SKY COMMANDER MODE HANDPAD OPERATION 10 10 USING THE HANDPAD AS A WIRED HANDPAD 10 11 ACCESSING THE RECEIVER V O 10 12 AUTOGUIDER PORT 10 13 RADIO HAND PAD AGENCY APPROVALS 11 LX200 to SiTechExe INTERFACE 11 1 INSTALLATION 11 2 LX200 COMMANDS IMPLEMENTED 12 NON SIDEREAL TRACKING USING THESKY 13 SATELLITE TRACKING 14 SKY WRITING 15 FUTURE PLANS 16 ACKNOWLEDGEMENTS APPENDICES Appendix A Tick Management Appendix B Planetarium Program Interfaces 5 of 236 130 131 131 133 133 133 133 133 134 134 135 135 136 136 136 136 136 136 137 137 137 137 138 138 138 138 138 138 138 139 139 140 140 142 143 144 145 148 152 155 155 156 156 158 Earth Centered Universe ECU TheSky Cartes du Ciel MegaStar Appendix C Database File formats Appendix D Periodic Error Correction Flow Chart Appendix E Sidereal Technology Servo Controller ASCII Command Se
179. he ServoConfig program While you watch the scope encoder and motor encoder location for the altitude raise the scope Both the Scope encoder and the Motor encoder should increase Check also the azimuth They should both increase when the scope moves from north to east Problem It tracks fairly ok but I think it should track better Solutions This could be caused by several factors the most common one is celestial pole mis alignment Use the maps provided in this document and star hop to the celestial pole It could be that the latitude isn t set up properly It could be that your mount is not level in the north south direction It could be that your drive system or encoders are slipping It could also be caused by the wrong values in the scope encoder configuration or Motor Encoder if using the SlewNTrack mode To check this use ServoConfig and from the main screen keep clicking on the Get Angles button Start at the horizon then move the scope to the zenith It should have moved 90 deg s Do the same for the azimuth Moving you scope clockwise will give you an increase starting at North should be 0 then to the East as 90 South is 180 West is 270 etc Also check the motor encoder ticks per rev If these are wrong the motors will operate at the wrong rates Keep in mind that the tracking math is proven and it works great When things are set up properly and you ve a good mount with no slippage the scope should track with
180. he Top Left ESC key for more than 5 seconds when the LED on the Servo Controller flashes fast you may let up Here are some screen shots from Earth Centered Universe which show placement for celestial pole alignment The QuickFinder has the two middle circles but not the outer circle The two middle circles are the same size in both the QuickFinder and the Telrad Limiting magnitude is 6 0 18 of 236 Telrad Placement for South Celestial 19 of 236 Pole Alignment 3 Ctarnaeleon b While the controller is in the DragNTrack mode the serial port can be connected to a laptop running almost any planetarium software Set your software to connect to a Tangent encoder interface box and you will be able to surf the sky using the planetarium software When setting up your planetarium software set up both encoder resolutions to 18000 Also do not use the option that your telescope is on a tracking platform Think of it like a telescope without a platform where you have this little guy pushing it all the time exactly keeping up with the stars That s what your planetarium program will think Also set the baud rate of your planetarium software to 19200 no parity 8 data bits and 1 stop bit If your software doesn t support 19200 baud rate contact us there is a way to set the controller to 9600 baud if you have firmware version 1 5 or later It s a good idea to set up the DragNTrack mode even if controlling with a comp
181. he current telescope azimuth and altitude are displayed numerically in the upper left hand corner When CalPointsXP is run from the command line it will automatically close in one minute A countdown timer displays the remaining time in seconds To prevent the program from terminating click the check box labeled Keep Open 210 of 236 Appendix K Version History SiTechExe Version History gt 055J gt Made Focusers work again I broke it last version I think gt ee k k k kk k k k k k k k k k k k gt 055H gt Added Reverse RA Guide mode while looking east gt Tried to get rid of the maxim camera in scripting so it calls up a new one gt Added if there is a comm timeout it tries to restart by going to gt normal mode then back to asciiCS Fixed the PXP date and time string gt when writing it for instance the date looked like this 09 10 202 for gt 09 10 02 gt Added debug to platesolve reading the co ordinates gt SPE TEETE EEEE E E E E E E E E E E E E E E e E e k E k E k E k E k k k k k k k k k k k k k kk kk k k k k k k gt 055G gt At RoweVille gt Working on pxp with Dave Made the terms be enabled by the Sensitivity gt instead of number of points gt gt Fixed the Script stopping if you stopped the script without finishing gt a slew gt Fixed the gem mode being to enable no wrap which screwed up the gt meridian flip gt Added J2000 coordinats to the goto thingy gt
182. he error in the interpolation routine seems to be pretty repeatable However to complicate things the distance between each of the 5000 lines is not 111 of 236 absolutely perfect either which makes the overall spacing between each of the very ticks between the lines 4 16 64 small ticks for the 320k and 4 24 100 for the 500k encoders not uniform It has the right numver of small ticks but they are not even The overall pattern of their not even ness is repeatable however due to the interpolation routine errors And that pattern repeats about every 17 23 seconds which is how often each of the 5000 lines comes by So Dan and Dave put their heads together and came up with a way for the software to watch how often the major lines come by i e every 64 or 100 ticks and then figure out the irregularity of how often they come by This is what has been called IPE Interpolation Periodic Error and then knowing this pattern of irregularity in the interpolation routine Dan applies a correction for it The results are quite amazing The PE for a mount is reduced to something around 1 to 2 arcseconds peak to peak for the mounts it s been used on with some mounts achieving results that even more accurate Unless the gurley and RA axis are perfectly coupled to the axis of the telescope i e no flex between the OTA and RA axis and no flex within the OTA to change the optical axis and the sky has no issues like seeing or refraction error
183. he servo controller 5 Tick Management TM Mode uses both the servo motor encoders and the mount encoders to adjust tracking speeds of the servo motors to correct for periodic error and slippage This is the mode to use with high resolution mount encoders such as the Gurley encoders If you select Tick Management Mode and you also use either the 320 000 or the 500 000 tick Gurley encoders you also have the option of using the Interpolation Periodic error correction routine to correct the interpolation errors inherent with the high resolution Gurley encoders by 62 of 236 checking the appropriate box TM mode is by for the most accurate mode It uses the telescope encoder information along with Motor Encoder information which creates a location that is much more accurate than the encoders themselves You can literally close the loop and eliminate all Periodic Error Non Periodic Error Backlash etc if you use fairly economical medium resolution encoders of 320 000 ticks or more Important Note Turning on and off TM mode on the fly after you have initialized the mount and while the system is running and keeping up with where it is can screw things up So right after you turn TM on or off on the fly perform an Offset Init to reset the system s knowledge of where it is How Tick Managment works When a new telescope encoder tick is received the controller grabs the position of the motor encoder at this point
184. heir eyepiece The latest release of MegaStar version 5 has a lot of great features including control of automated telescopes Please read more about Megastar at http www willbell com SOFTWARE MEGASTAR index htm However the version 5 release was made before the ASCOM initiative got rolling and therefore lacks the interface to the large number of ASCOM complaint telescope drivers that are available today MegaStar To ASCOM is a program that allows MegaStar to connect to these ASCOM compliant telescope interfaces MegaStar To ASCOM makes use of the LX200 telescope interface that is built into MegaStar Version 5 The program is basically an interpreter that converts the LX200 language that MegaStar speaks into the ASCOM complaint language that the ASCOM telescope drivers use The simple block diagram below outlines the concept Virtual Null Modem Connection com0com MegaStar v5 ASCOM Telescope Telescope Driver Another Astro Program The block diagram above is in the user s manual for MegaStar To ASCOM and reflects using the ASCOM Hub POTH to be able to connect multiple ASCOM Programs to the telescope driver SitechExe exe SitechExe already has an ASCOM hub built in so you should not have to use the POTH option to connect multiple ASCOM programs to SitechExe In addition the LXtoSitech program also provides the same type of LX 200 interpreter capability also available for download from the Sitech user s web
185. his is a fast moving error it s hard for an autoguider to compensate We should point out that this error is well within the specifications of the Gurley encoder it s just that none of us were expecting it to be that fast of an error So after thinking about the problem for a few days Dan came up with a solution He mentioned this to Dave Rowe who was skeptical However he modeled it and found out it would work quite nicely Here s the concept There is an average number of motor encoder ticks between each scope encoder tick This value will vary from scope tick to scope tick depending on the interpolation error but it is consistent for each cell of different 64 scope ticks per scope encoder line Dan programmed the SiTech controller to count each motor tick between the telescope encoder ticks and put them in a 64 byte buffer This buffer is read out to the SiTechExe program every time the 64 ticks roll over to zero again just over 17 seconds with the 5 000 line Gurley encoder while moving at the sidereal rate Now the SiTechExe program averages these ticks to average any changes because of worm gear periodic error and then converts the 64 cells representing motor ticks to scope ticks into an angle This angle is integrated depending on which scope tick the scope encoder is currently on Then a standard tick management is applied to the cell that is the current cell to find the fractional angle of that particular cell N
186. hoo listserver site and in the files section of their listserver there is an excellent user manual for overall Sat Tracker operations 148 of 236 Configure Sat Tracker to control a Meade LX200GPS Polar mount no matter what type mount you actually have using the Telescope Interface screen as shown in the screen grab below After starting LXtoSitech exe which will also start the freeware program HW_VSP to create a virtual comm port 5 connect Sat Tracker to Comm Port 5 W Telescope Interface Note Meade Lx200 2 7 7 This setting allows for continuous tracking with the Meade Meade Lx200GPS LX200GPS telescope Firmware 1 5c or later is required C AltAz Polar For Leap Frog tracking use the Autostar 497 interface Meade AutoStar 494 setting If the tripod if carefully levelled tracking will be improved Changes to the Timing Offset or Alignment Meane autos A ARN Adjustment while tracking will take 5 to 10 seconds before 1x200 Compatible taking effect Remember having your computer time set Ultima 2000 NexStarGPS NexStarGT very accurately and a fresh TLE file is critical The NexStarGPS Continuous Tracking Tracking Method and Tracking Factor settings have no ie Cc ic effect with this interface Celestron CGE Continuous Tracking NexStar 5 8 Log File OK Cancel You will need to download the trajectory data for the satellites that SatTracker exe uses to generate its tracking command These fil
187. hould look something like this lt 2 7 20 2 This means that APN_0001 in Cepheus is 2 7 degrees east and 20 2 degrees up from the scopes current location First test the azimuth encoder for direction by pressing the left directional button on the SiTech hand pad Move the scope about 10 degrees toward the north west with the left button The 28 of 236 display should look something like this gt 352 7 20 2 If your azimuth encoder is setup correctly it will show that the scope needs to move back east 7 3 degrees 360 352 7 7 3 Since the scope started 2 7 degrees from the target and we moved the scope 10 degrees in that direction it overshot the target by 7 3 degrees This is correct If the azimuth display on the Sky Commander did not change see the trouble shooting section below If the azimuth number incremented from 2 7 to 12 7 roughly then the encoder direction is probably reversed in the Sky Commander see setup above Next test the altitude encoder setup Press the up arrow on the SiTech controller Move the scope up about 10 degrees The display should look something like this gt 352 7 10 2 This shows that we moved 10 degrees toward our target still APN_0001 If the altitude encoder value changed from 20 2 to 30 2 then the encoder direction is reversed in Sky Commander Once the encoder direction is correct the system should be ready for use Note that proper pointing requires
188. ht and top left key presses ESC dim the flashlight When the flashlight is on the normal functions of the top right and top left key are disabled The flashlight automatically turns off after about 7 5 minutes 135 of 236 10 4 9 Keyboard Lock Mode In this mode the only keys that are operational are the direction keys Up Left Right and Down keys and the combination ESC and RTN pressed at the same time You must select your preferred speed before locking the handpad This mode is very useful at public star parties and provides the option of giving the handpad to the general public for panning the moon etc without re initializing slewing etc It may also help you on those very late nights fumbling in the dark To lock the keypad hold down the ALT key and press the Up direction key scope will not move if the ALT key is pressed When the handpad is in the locked mode and the flashlight is off the LED s will flash if an illegal key is pressed To unlock the keypad hold down the ALT key and press the Down direction key scope will not move if the ALT key is pressed After an automatic power down the keyboard will automatically be unlocked 10 4 10 Turning the Handpad On To turn the handpad on simply press the SPD key The unit powers up and remains on until about 15 minutes have elapsed or a user turns it off 10 4 11 Turning the Handpad Off To turn off the handpad hold down the
189. i RA IRA DEC Dec yuog sudgojor sampay siaquiny adoas Cre AltiAz STOP Stopped Bad Scope Commun Ra 07 54 09 0 Sep HrAng 11 59 59 Dec 00 06 31 Focuser Field Rotate Motors Automatic non stellar objects to use for Initializations and GOTO capability Most of the time you will simply use an ASCOM compliant planetarium program like TheSKY or Earth Centered Universe ECU or the free Cartes Du Ciel to connect to the Sitech driver SitechEXE and do your initializations and GOTOs using a Graphical Unser Interface GUI by just clicking on your target In the spirit of walking before we run however the manual will cover the basic capabilities on this tab and in doing so also introduce you to how to do initializations for the system We will leave some of the more advanced capabilities like Scroll files and building your own 49 of 236 Database files to the Advanced section Explaining how to set up and use various ASCOM Compliant planetarium programs will also be covered in the Advanced Features Section 4 6 1 Scroll FileName Data files are saved in the c program files common files ascom telescope sitech database If no data file has already been loaded the second button from the top will be labeled ScrollFileName If a file has been loaded the filename will be the label for the button Database files are just that data on targets with their identifying information a
190. ic pwm frequency Tracking is 31 KHtz slewing is 7 or 8 KHtz 0 FAS 2g 2g E K os K K K K K K K K K K K K K K K K K K K K K K K zd Version 1 6 Changes Added reciever 2 way protocol added support for ArgoNavis Goto s fixed calculate latitude bug Fixed old Stepper handpad bug Fixed guide bug with stopped declination Press TopTwo buttons on handpad and system will try to put motors back in auto DONE Added Ascii Commands add command to operate the digital outputs XXQ 0 1 2 or 3 added command XXN for argo navis setup 0 or 1 following four commands have been added for future use gt lt XK Local Search Distance gt XXM Local Search Speed gt XXO Altitude Backlash XXP Azimuth Backlash Changed the Default Speed in the flash rom to be backlash unused in 1 6 made default platform goal be 10 000 000 default is a telescope not a platform made default integral be 3 000 Made lights alternate flash if tracking paused equatorial DnT SnT and ArgoNavis Improved some code to make more efficient Moved all flags to the bit area Now resets itself after an upgrade 2 on encoder bugs me fix drop out of all auto tracking when recieving any valid picservo command 0 AS 2g 2g 2g 2g ig is K K K K K K K K K K K K K K K K K K K K K K K kd Version 1 7 1 8 1 8A 1 9 changes 232 of 236 0 DONE Three bug fixes EStop and X_Bits and another guide bug 1 DONE found bu
191. iding status Selecting this option will always have the answer be false even though the mount is still working on the previous guiding pulse command So a second guiding command to that same axis can be sent immeadiately improving response time If the previous command has not finished being executed it will simply stop being executed and be replaced by the later command if for the same axis The beauty of these commands is they are different ways to allow an autoguider to keep hammering away at an RA error without ignoring the Dec axis However there is a caveat there always is right You should NOT use either option during the autoguider calibration sequence since at that time you do NOT want to fool the autoguider program Then check one or both after the calibration has been completed 109 of 236 7 HIGH RESOLUTION MOUNT ENCODERS SiTechEXE has a feature called Tick Management TM that enables the mount to combine the information from the mount encoders with the motor encoders to dramatically increase the effective resolution of the mount encoders can be up to 10x better If you use high resolution encoders on the mount such as the Gurley 320 000 tick or their 500 000 tick encoders along with the servo motor encoders you can virtually eliminate periodic error while tracking You can also use a normal 8192 tick encoder if you gear it up to get more ticks per rev of the axis it is attached to There are examp
192. ies OOK On Off Keying transmitter and receiver chips The crystal controlled frequency used is 433 92 Mhz The antenna is internal to both the transmitter and the receiver A very quick bit rate and only 16 bits per packet including address data bits and error checking are needed to activate the receiver This is one reason for the perceived instantaneous response While a button is pressed on the transmitter there is an initial burst of data and following this there is a burst of data every second Each burst is very short and is 2 packets of data in case of interference during one of them Included in this burst of data is the address and the data and a checksum Now when the button is released there is another burst of data which has the key released information The receiver is programmed to expect a burst every second and if it doesn t get an expected burst it will stop Normally this will not happen as it will get a burst when the key is released which will stop the movement of the telescope but it is there for safety in case both key release bursts are missed You can order the handpad without the radio components and it will serve as a wired handpad SiTech Controller only In order to upgrade from a wired handpad to a wireless system you will have to purchase a receiver and send the handpad back to our factory for addition of the radio components The cost of the wired handpad and upgrading to the wireless will add
193. ight Ascension axis enter that number on the green text box to the right After pressing the Enter key the proper Equatorial rate will be calculated and will appear in the equatorial rate text box this rate will account for Sidereal You need to set the direction of tracking fofr operation in either the Northern or Southern hemisphere The way to set this is to point the scope toward the west and observe the direction of motion when the handpad buttons are pushed Pushing the West button on the right should make the scope move down toward the horizon Pushing the UP button should make the scope move toward the pole North or South depending on the hemisphere If the movement is not as described you will need the reverse the servo direction using ServoConfig software You can adjust the tracking rate up and down by pressing a certain sequence on the handpad The amount it is adjusted per handpad press is in the text box labeled Equatorial Up Down Adjust If you have a platform set the Tracking Platform Goal to the number of motor encoder ticks where you want the platform to stop The SiTech controller will stop at this point and then you can then perform a re wind If you have an equatorial telescope set this platform goal to over 10 000 000 This will make it impossible to stop at the platform goal it will continually track forever if you don t stop it If the motor tracks the wrong way you can put a negative number
194. il the star is centered As soon as you do an offset init your telescope will start to track If you ve an Alt Az telescope the tracking will be based on your latitude and longitude that you will need to have entered in the configuration window and assumes your scope is level If your Lat Long is accurate and the mount is perfectly level you are probably fine with a single Offset Init However if not perfectly level or Lat Long is only approximate even though your GoTo s will probably not be too accurate yet since the mount will be tracking this will give you time to re center the star to accurately re load load your first init point If you ve an equatorial telescope if you re polar alignment is good and you have a good telescope mount model loaded you may not want to add the complexity of adding Cal Star init points it may be accurate enough as it is 4 8 2 Cal Star inits Instead of shifting the sky which effectively the Offset Init does the Cal Star inits load the hour angle declination primary axis angle secondary axis angle into a matrix As soon as the 2nd star is loaded the polar transformations are performed to convert between the telescopes primary and secondary axis and the Hour Angle and declination of the object s If you have a mis aligned equatorial telescope your goto s will be accurate even though you re mis aligned after you load the 2nd star Cal Star inits are also the type of inits that are used when you d
195. ill finish even with bad pointxp file gt gt 055A gt Added checksums on the ascii protocol gt fixed the HH MM DD Time2Rads bug gt Logged error when writing fits file default fit gt SCTimer can t run two instances FAS 2g is FAS K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 054M Created TrapLog of SeriallO Fixed the interface with the latest version of PlateSolveXP Added the direction switches when calling calpointsxp Made won t go into slew if in the offset rate mode We let the offset rates do it Mad Handpad slip mode return the ra and dec if there was no errot Took out the write over pxpscript message Not necessary and annoying Maybe fixed the jumping problem I ll find out soon Has to do with the time from controller If Axis Rate command is faster than the slew speed it makes it be the slew speed Made errors work even if motors reverse if in handpad slip mode 054L Trying a couple of options with PulseGuiding 1 Return never pulse guiding 2 Instant total movement Log the RA and Dec setpoints in the PulseGuide method 212 of 236 054K Only try 2 times to write to SeriallO txt instead of 10 times Logging more stuff average tdiff in PulseGuide Can SyncToAltAz down to 0 0 deg s elevation not the lower limit in cfg Alt Low Limit will accept 0 0 deg s now added RA moves to goal when moveing extrem
196. ill have been covered and in fact basic operations of the mount do not even need a PC to be hooked up to the controller Remember we want to learn how to walk before we run This section includes information on how to use your mount in a standalone mode without a PC connected i e in Drag amp Track mode Slew amp Track Mode or Equatorial Mode You should do this to get familiar with this capability even though in the future you plan to normally always have a PC connected to be ready for those times if when your laptop dies At this point you will want to transition to this OPERATIONS manual It starts with a review of the basics of using the system without a PC Then it focuses on learning the basics of using the powerful Sitechexe program on your PC to add important capabilities like GOTO and how to use external programs like planetarium programs to control your mount i e click on a target in the planetarium program to aim the telescope at that target etc The Operations manual will start with how to install Sitechexe and some related software that it needs to have installed And just like with the controller Sitechexe will need to be updated with some basic information about your mount and your location etc So that will be one of the first things covered Now you will have a mount that has a really sophisticated control capability but a very straightforward user interface We recommend you spend some time at this point simply
197. image from within PlateSolveXP and the Fits header will have RA Dec plate match parameters and FOV saved to it 5 1 3 Scripted PlateSolveXP Operations Dave Rowe wrote an additional program called CalPointsXP that calculates optimum locations for calibration points based upon the number of points desired the user s local horizon and the type of mount The integrated software is able to perform a complete mount calibration by automapping without user intervention Place the file CalPointsXP exe in the Sitech Folder To use PlateSolveXP and CalPointsXP just click on SiTech Features Run Script SiTech will open the Script dialog box and the Camera Control software specified in the SiTech Change Config Miscellaneous 80 of 236 Ei Script CurrentCommand Stopped Add Slew tichT extBox1 Stopped Add Pan Add Anchor Add SlewTo amp nchor Pause Load Script Add PanTo amp nchor Stop Play Save Script UnPause Clear Script Add Pan Relative Add Pause Make a PointXP Platesolve Script Add Prompt How Many Cal Points Exposure Binning Make Poin P Run Add Wait je 4 py p H Add Sound Use SiTech Init Window Do a single photo init Add While r Add Loop Click here for HELP Cancel Colors The script Window in the features tab has a section titled Make a PointXP Platesolve Script This allows you to setup a script for SitechEXE to run that will automatically figure out what the optimal spaci
198. in SitechEXE to allow it to communicate with the controller if the information in the controller does not match the default info on SitechEXE you will get asked if you want to use the information in the controller Click on YES That will update some but not all of the SitechEXE configuration information The remaining configuration information will be done using the SitechEXE configuration screen We will do that as part of introducing you to the various screens in SitechEXE 35 of 236 4 1 BASIC FEATURES There are a LOT of capabilities to learn about and at first glance it might seem very intimidating So the idea in explaining this is to divide things into the Basic Features and the Advanced Features As the features of each of the Sitech Windows are introduced the details of the Basic Features will be covered in detail and the Advanced Features will be introduced at an overview level with the details of the Advanced Features covered later in the section on Advanced Features If a feature is considered an Advanced Feature its title will be identified as ADVANCED FEATURE After you have gone through this Basic Features section of the Manual you will be able to initialize and operate your telescope using many of the powerful capabilities like GOTO at a basic level using your PC 4 2 COMMON AREA OF THE SiTechEXE SCREEN STOP Tracking Ra 14 50 41 3 Scp HrAng 1 7 18 23 Dec 74 06 5
199. in database capability with alignment stars and Deep Sky Objects Messier NGC IC for synch or GoTo slewing Customization of the display of SiTech exe controls on a PC allows you to set the colors of buttons and displays to suit your taste Windows Configuration program is supplied free with the unit or is available online for free downloading Very active user community with an e mail list server and a user community Website http www sitechservo info 1 3 COMPARISON BETWEEN STEPPER SYSTEM AND SERVO SYSTEM A servo system has many advantages over a stepper system Wider dynamic range This means a servo system will track your telescope nearly perfectly and still obtain faster slew speeds than a comparably geared stepper system Angular accuracy of the motor while tracking is much better There are many errors in a stepper system when being micro stepped Generally speaking the micro steps are not nearly as accurate as the resolution of the micro step There are many errors such as mechanical winding differences magnetic hysteresis torque error and several others that can be partially compensated for in software with a stepper system but never will be as good as a servo system which will almost all the time be within 1 encoder tick of it s desired location at all times while tracking More torque Small servo motors will control telescopes as large as 41 inches Much lower current during tracking Batteries will last much lon
200. in pointing so that the scope can achieve extremely accurate pointing down to a few arc seconds accuracies and because the mount geometry is now corrected also results in significantly improved tracking accuracy PointXP was created by David Rowe Dave generously loaned Dan Gray the source code for PointXP and Dan converted from Visual Basic to C Special thanks to David Rowe The PoimtXP engine takes a series of Calibration Stars performs some very complex transformations Gauss Jordan Partial Derivatives and more stuff that s way over my head and does a fine job in correcting for many telescope mounting errors and mount flexture PointXP By Dave Rowe Incorporated by permisson iol xi Terms to Include in Model 91 NF N0 10 Model Sensitivity 141 1 Term 0 01 05 33 Term 1 00 19 15 M Cone Z2 00 14 12 X Term 2 00 00 01 Term 3 00 00 02 MV Hub 21 00 06 24 N V DecImbalance 00 07 03 E Longitude M RAlmbalance 00 02 12 122 42 05 MV DecTransverse 00 01 43 Latitude IV RATransverse 00 02 55 A 45 33 55 V Dec Droop cos 00 01 48 z M Dec Droop sin 00 01 01 Baro Pressur pe 1020 31 8320 MV Alt Sin 2 Phi 00 00 28 MV AltCos 2 Phi 00 00 37 F Temp Dea s IV Alt Sin 3 Phi 00 00 27 L k AltCos 3Phi 00 00 36 Sanat Jalt az 7 AltEnc0 359 59 58 Time Z AzEnc0 360 00 00 a ight Sav Read Config Write Config Save Clear Terms And Cal Stars Clear Stars Leave T
201. indicates how far the scope needs to move The direction is represented by an arrow and degrees from 0 that the scope needs to move See initial setup section above To perform GOTO s at any time simply select the intended target in Sky Commander and then press the top 2 buttons on the SiTech hand pad The telescope should begin slewing to the object immediately It is a good idea to watch the countdown values on the Sky Commander until you are confident that everything is setup correctly Additionally it is good to check that the intended target is reasonable in terms of the limits of your scope particularly for Dobsonians which have lower altitude limits If your initial slew was correct then you should be able to select subsequent objects in the Sky Commander and then press the top 2 buttons on the hand pad to GOTO that object 2 5 6 Initial Setup and Testing of Equatorial Sky Commander with SiTech TBS 2 5 7 Starting and Using SiTech with Sky Commander for Equatorial Ops TBS 30 of 236 3 OPERATION WITH A PC 3 1 SOFTWARE USED The SiTech controller system can operate without a PC connected as described in the previous sections however a PC must be initially connected with a serial cable to setup the controller and configure it to match the mount Two software programs are required to configure the Controller to work with the mount ServoConfig exe is used to set the ticks and motor control parameters for your mo
202. ing something like 250 or so If the cursor movement is too jerky during slews use a smaller value for the refresh rate The Observatory data and the RA Dec will fill in from data passed from Sitech after you connect Click on Configure if you want to go directly to the Sitech Config screens When ready click on Connect bottom left button and the red box will change to green when connected ASCOM Telescope Interface 1 3 Driver Selection SiTech Telescopd Refresh rate 1000 About Observatory Latitude 29 46 3 Longitude 95 24 26 Set Location Set Time RA OOhOOm00s DEC 00 00 00 wi az ALT Tracking Abort Slew Help Disconnect Hide 170 of 236 MegaStar NOTE A good deal of the information in this section was used paraphrased with the permission of the author of the program MegaStar To ASCOM and per the permissions stated for com0com The files required that are mentioned in this information are available on the Sitech user website DOWNLOADS page at https sites google com a sitechservo info home downloads in the file MegaStar To ASCOM zip MegaStar Sky Atlas is a great sky mapping program With its first release back in 1991 it became the first start charting program to include the 15 million plus stars in the Hubble Guide Star Catalog GSC The GSC provided the reference stars that were essential for serious deep sky observers to identify all those faint fuzzy objects in t
203. ion by incrementing or decrementing the numeric up down button You will see the black line on the graph change If there is a black line that is in bad disagreement 198 of 236 with the others delete it by clicking on the Delete Collection Item 9 When you re happy with all PEC tables in the collection be sure to save the collection for later use Now you re ready to load the final averaged PEC table to the controller Click on the button labeled Send Averaged Table to controller 10 Be sure to save the table to flash ROM by clicking on Save Table in Controller RAM to Flash PEC Playback If you have a PEC table saved to flash then this is the procedure to get playback going If you have an automatic PEC sensor then you can program the controller to start playback automatically on powerup To do this use ServoConfig version 1 1 or later 1 If you don t have an automatic PEC sensor call up the PEC screen in the SiTech ASCOM driver 2 Click the button labeled Arm PEC Playback 3 Wait for the worm to line up with your reference and press the top left button on the handpad PEC will now be active and will be even after slewing the scope 199 of 236 PemPro PEC Training For details reference section 5 2 11 1 Verify tweak polar alignment 2 Clear out any PEC curve in the sitech controller e PECGraph display in Sitechexe click on Clear PEC Table in Controller in the left column of buttons e Verify the P
204. ith this information to eliminate this uncommanded motion for the RA axis of an Equatorial Mount currently it only works for equatorial mounts not for Alt Az mounts It is only as accurate as your inputs are so it allows recording several runs and averaging and smoothing them Alternatively you can also use the outstanding PEC correction routine PemPro by CCDWare SitechEXE has a custom interface to PemPro that makes using PemPro very easy Since programming your PEC is not mandatory for Basic operations the details of this powerful tool will be covered in the Advanced Features Section This should probably be the first of the Advanced Features to come back to unless you are using a high resolution encoder like the 320 000 or 500 000 tick Gurley encoders The reason is excessive PE can degrade using PointXP to model your mount If you ARE using high resolution encoders 8192 encoders are NOT considered High Resolution then do not use this capability PEC is Playing 174 24 03 04 Cntr Buff Status Loaded 10 Arc Seconds x Use Auto PEC Syne V Clear Collective m Show 5 Collective Items IV Clear PEC Table in Controller Load Collective Item from Controller Buffer Show Current Collective Item I Arm PEC Record Load Collective Item from File Buffer Show vernge V Arm PEC Playback Load PEC Collective Show Latest From Controller IV Read Cntrler PEC Table into Cntrler Buffer Save PEC Collective P n Show PEC Fil
205. k on the fast button pressing the top left and the top right buttons will rotate CCW and CW fast There is a communication delay for this and the start and the stop of the focuser will be delayed somewhat It would be better to use a separate handpad for the focuser The next layer of buttons is Jog LftFld or RtFld to a specified amount Set up the Field Jump Size then when you click on the LftFld and RtFld the rotator will move exactly that far Between these two buttons is a Track or Stopped button If the rotator is stopped click this to start the tracking at the parallactic rate Next you can set up an angle then click the button on the left and the rotator will move to this new position 129 of 236 10 SIDEREAL TECHNOLOGY RADIO HANDPAD This exciting new product from Sidereal Technology has many cool features in addition to remote handpad control of your telescope or tracking platform This product was engineered and tested by amateur astronomers for amateur astronomers 10 1 RF HAND PAD FEATURES 1 2 Connects to the Sidereal Technology Dual Servo Controller for wireless remote control of your telescope Eliminates the wired Handpad for tangle free operation Emulates the old standard Mel Bartels Stepper System Handpad The receiver has a mode which emulates the original Mel Bartels handpad so can be used with the Mel Bartels Stepper system with only the application of a jumper and a ground wire Addressable easil
206. k to fix this Solution You may have slippage or dropped ticks You can use the determine tics window in Servo Config moving the scope through 90 to verify by moving back and forth whether the error is different each time If your mount uses friction drive or a soft clutch look for signs of slippage However if there is no slippage then you are dropping ticks on one or both servo motors Dropped ticks usually occur from a weak electrical signal or electrical noise Long cables or cables running near other electrical devices may have electrical noise and cause tick count errors You probably need to add pull up resistors on the A and the B wires Use a 2 2K resistor from the A and B encoder leads to the 5volt pin You can put these resistors anywhere near the controller or near the motor Also shortening a long cable may work and we have experience that flat phone type cable works well but computer cable like Cat5 doesn t work very well Problem On my new SiTech installation on an equatorial mount my mount tracks for a while in RA then jumps a couple arc min then jumps back several times in a 10 minute period Solution This shouldn t happen it could be that your integral is set too low One thing to do is click on the numbers tab and watch the PAxisError It should be near zero all the time If it suddenly starts moving then we know that is where the problem is occurring Another thing to do is call up the features tab then c
207. king east we force AltOpposite to be east so the proper z s are displayed FAS 2g 8 FAS KE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K og K 0 30 Fixed R A Dec display to display true ra dec instead of apparent ra dec Fixed No Semi colon on co ordinates bug in scripting Changed scripting message to Stopped instead of current command Added Hot Configuration changing and fixed scope latitude on change Added auto unpark on startup ignored if not parked previously If declination rate then declination hyst is ignored EEEE E E K E K K E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2k K K 0 29 First attempt at scripting Fixed crashing on help in ECU EEEE KE E E 28 E E K E K E E E K K E K K E K K 2s K K K K K K K K K 8 K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2 K K 0 28 Tried to fix the scaling issue of the PEC Graph no scale on right this AutoScale false This worked KKK 2k ok of of K K K K K K K 2k K K K K K K K K K K 2k K K K of K K K K K K K K ok of K K K K K K K K K K K K K K K K K K K K K ok ok K K K K K K K 0 27 Added Calibrate Tracking Rate feature Added Directory Path Automation so it will work with other languages KEKE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K K 3K K
208. l reading Then save your PointXP file Also save your terms to the config by clicking on Save Config in the PointXP screen Now next time you set up at home call up PointXP click on clear terms and cal stars Just in case an auto reload from an unpark command then click Read Config This will load up all the terms you previously saved but still no cal stars are loaded Now load about 3 or 4 stars using the Just Load Star No Terms button this is on the Init screen then after you load the last one click on Calc Only Offsets Align You will be keeping the terms of your full run but just fitting the best alignment with these stars Alternatively build a very accurate Sitech hrz horizon file for the sky you have This will not be as good as building a model of the mount using the whole sky but will hopefully allow you to improve your performance till you can build a complete model and it will be good practice for when you are out in the open Just be sure to not use the constrained horizon file while you are out in the open Build a new one that reflects the open area Problem When I use PXP and load Cal Stars I see the Model Sensitivity for the terms checked but I don t know which terms I need What are the terms Solution Generally use the terms in order from the top down keeping the model sensitivity in the green 1 Cone Z2 This is a fabrication error It is sometimes called Collimation error as it is the err
209. lack eyes 10 4 7 Normal Slew Pan Guide operation The arrow keys on the handpad will operate the telescope You can move Altitude Declination and Azimuth Right Ascension at the same time if using the SiTech Servo system If using Mel Bartels Stepper System simultaneous combinations are not possible To change speeds simply press the center SPD button for 1 8 to 1 4 of a second If using the SiTech system you will toggle between the Slew mode to the Pan mode and then the Guide mode then it will be in the slew mode again You can watch the lights on the receiver to see which mode you re in You must be using version 1 6 or later in the SiTech servo controller for the lights to operate properly and also to sequence into the guide mode If you are using Servo version 1 5 or earlier in the SiTech controller you will only have the Slew Pan modes and the indicator lights will not work properly This will be evident because the slew and pan LED s will be on faintly but when the SPD button is pressed the slew and pan LED s will get brighter If using the Stepper system your choices are Slew and Pan modes The guide mode will only be available from the Guide port and also the Scope exe software will have to be put in the guide mode 10 4 8 Flashlight Operation The top center button among many other uses is used to turn the flashlight on and off When the flashlight is on top right key presses RTN brighten the flashlig
210. leAPI dll to TeleAPI Original dll The TeleAPI that comes with TheSky is really just a dummy dll that doesn t do anything 2 Copy the ASCOM TeleAPI dll to C Program Files Common Files System TeleAPLdll One time Telescope Setup 1 In TheSky Telescope menu select Setup You must tell TheSky what scope you will be using and what features you want to use TheSky6 jentation Data Tools Telescope Help Bere se eva i via 4 m Options Server Settings 165 of 236 2 In the Control System box select Telescope API You must have loaded the replacement TeleAPI dll before this step Telescope Setup PR Telescope or control system Name Telescope API X Simulator Ultima 2000 by Celestron International Telescope API Deep Space Navigator Autostar by Meade Instruments Corporation NexStar 5 or 8 non GPS model by Celestron International Paramount ME or Paramount GT 11005 by Software Bisque TheSky Box by Software Bisque Astro Physics GTO German Equatorial Mount Sky Tour by Tele Yue SkySensor 2000 by Vixen Gemini by Losmandy NexStar 5i 8i 8 GPS 11 GPS 60 80 114 and CGE models by Cel L200 GPS by Meade Instruments Corporation Temma by Takahashi ServoCat by AxDesign 3 Click Settings to open the ASCOM Telescope Chooser and select the ASCOM compliant telescope you wish to use Telescope Setup Telescope or control system Name Telescope API Settings Select the type
211. les in the appendices for attaching mount encoders to your mount The TM feature can be turned on in the Change Config Scope Encoders tab TM benefits RA axis on equatorial mounts the most The DEC axis doesn t need TM since there is no tracking however even using lower resolution encoders like the standard 8192 tick versions slewing to targets and pointing can be enhanced with TM SiTech can also use TM and these mount encoders on Alt Az mounts where tracking requires motion of both axis The recommended Gurley 320K encoder is part number RIS8SOSOO0OQSLI6AN18SPO4EN The recommended Gurley 500K encoder is part number R158SO5000Q5L25AN18SPO4EN SiTechEXE supports both encoder models As of the writing of this manual the 320K Gurley is used on several mounts and provides exceptional tracking accuracy with virtually no periodic error on equatorial mounts The 500K Gurley has been tested and works well also Other high resolution encoders can be used however the Gurley encoders are specifically accommodated by the SiTech software Initial testing of the Gurley encoders shows that they have an internal interpolation periodic error IPE Dan Gray and Dave Rowe devised a way to automatically measure this IPE and correct for it in SiTechEXE This compensation is automatically turned on when the SiTechEXE IPE option is set for the Gurley mount encoders It takes SiTech a couple minutes to fully incorporate the IPE corrections so let the mount settl
212. lescope mount s servo motors are controlled In addition autofocusing software routines that are ASCOM Compliant can directly interface with the focusers It also allows you to store 20 different setpoints to remember focuser positions for different cameras and eyepiece and filter combinations to quickly and accurately refocus There are two focusers supported because many users have both an imaging telescope camera and an autoguider telescope camera For imagers that do not use a motorized focuser you need to use one Once you experience the ease of making tiny focus adjustments with a motorized focuser you will find the difficultly of achieving a sharp focus for your CCD camera is greatly reduced A recently added capability by Dr John McClusky provides for Temperature Compensated Focusing TCF control for the Imager Focuser not for the 2 Focuser that can be supported normally reserved for the Guider Focuser This allows you to calibrate your system for how its focus changes as the telescope changes temperature and then using a simple temperature sensor that plugs into the Focuser Controller AUX Inputs Port will automatically adjust the focus as the temperatures change There are separate screens for the focuser and rotator capabilities and they are enabled by checking these boxes Then you call them up by clicking on the appropriate boxes at the bottom of the Common Area on the Sitech Main Screen Since the use of a s
213. libration points PointXP PXP is simple to use 1 Be sure you ve done a ClearTerms and Cal Stars Then perform an Offset Init on a star to ensure tracking is active 2 Do at least 16 Load Cal Star initializations you can use your planetarium program s Sync button after slewing to a target and centering it These should be scattered around the sky Click on the Errors Toggle button to see area s of the sky you ve missed You can click on a blank area and perform a Goto to this area 75 of 236 3 Click on Save CalStar file to save your work Important Once you start LoadCal Stars type of Sync then don t do a Simple Offset Init until you re all done loading cal stars Once you do a Simple Offset Init then you shouldn t do any more Load Cal Star inits unless you want to start over PointXP calculates many errors but it needs at least 16 Load Cal Star locations to calculate all the terms For GEMs these stars should be both looking East and looking West The SiTech driver will automatically load up the pxp file that was in use at the time of your Set Park command If you ve moved your mount or changed something in your mount you may want to do another calibration run and another set park Suggestions for Alt Az scope initializations e Take your first two stars at about 45 deg elevation and from about 90 to 120 deg apart in azimuth The two stars will then give PointXP enough to calculate the zenith o
214. lick on controller stuff Put your mouse in the Primary Axis OUTPUT window and watch the controller output If during the problem this climbs and climbs then suddenly lowers when the scope returns then you may want to look for a mechanical problem like worm or axis bearing binding or cable hang ups etc You can also put the mouse in the primary axis Error window to see what the controller error is during the problem Problem I just added a Gurley encoder to my RA axis and tried to use Tick Management and the Gurley IPE My mount doesn t track well at all sometimes tracking slowly backward and sometimes jumping several arc minutes When I turn off TM and ignore the scope encoder tracking is very good Solution The SiTech compares the position from the servo motor encoder with the Gurley when using TM If there is ANY slippage in the servo drive OR the Gurley encoder shaft connection to the mount you will have problems If you do not have slippage make sure the Gurley installation doesn t put a side load or an axial load on the encoder shaft A flexible shaft coupling or a soft mount of the Gurley should prevent problems Also check the comparison of motor and mount encoder position by opening the Features Controller Stuff in SiTechExe If these numbers become more different you probably have slippage somewhere There is one more place to check if you are using Precise or Polite Mode Click on Change Config Scope Encoders and look
215. llowed a remote chance of the flash memory to be erased You will have to send the controller back to the factory for a re program Problem Motor gets abnormally hot Solution Check the motor current You can do this using the ServoConfig software The motor current appears on the main screen If more than 0 5 amp while the scope is moving slowly you may have more friction on the gear train or maybe your scope is out of balance Sometimes worm gears add a lot of friction to a drive system Be sure the thrust clearance on the worm is not too tight and be sure the worm pressure against the wormgear is not too much Be sure lubricant is applied properly Problem Upon applying power one of the motors starts slewing all by itself Nothing will stop it Solution Unplug the handpad and see if it still happens If it stops moving you ve a faulty handpad If it keeps on moving it may be there is a problem with the digital input for the handpad Please contact us Problem I hooked up things again as I had unplugged some of the cables from the controller box stupidly I switched the power cables to the motors where they plugged into the controller box IE had the altitude cable plugged into the azimuth port on the controller and the azimuth cable plugged into the altitude power port I did have the telescope encoder cables plugged into the correct ports When I powered up the system in a few seconds the scope just starting moving in altitude at a
216. log stars by a cyan X and matched stars by a yellow circle These symbols can be turned on and off by clicking on the appropriate toolbar buttons The button labeled lt gt toggles between the original image and the image processed by background subtraction and spatial filtering Using toolbar buttons one can also zoom in zoom out and adjust the white and black levels Right click on the image to zoom or center 6 Inspect the match in the Parameter form In the Stars frame find the number of catalog extracted and matched stars and the RMS difference between catalog and image positions over 207 of 236 all matched stars The exact image center is given in J2000 0 coordinates in the mage Center frame and the details of the plate geometry are given in the Plate Geometry frame The Stretch is the scale ratio between the x and y axes and therefore should be close to unity in absolute value The Skew is the image shear and should be very close to zero The Pixel Size is given in arcseconds and the Plate Size is given in arcminutes or degrees 7 After a successful match the cursor location will be displayed in J2000 0 coordinates in the readout bar along with the image coordinates and the intensity of the image at that pixel The brightness and background of the displayed image can be adjusted using the Set Levels command button denoted by the histogram icon and also available from the View pull down menu Adjust the minimu
217. low cost and as it turns out slow periodic error The disadvantages are a Possible slippage if used as a roller b Adding backlash gears c Fast periodic error gears or timing belts d Can have a very large slow periodic error rollers gears or timing belts It turns out that a very small 1 to 2 thousandths of an inch de centering of the roller creates a considerable amount of slow periodic error so it pays to make sure the encoder mounting is as accurate as physically possible 2 Purchase a medium resolution Gurley Encoder I recommend the 320 000 tick per rev after quad 157 of 236 Appendix B Planetarium Program Interfaces One of the most powerful and useful Sitech capabilities is to interface with ASCOM Compliant Planetarium programs and telescope control routines inside CCD imaging programs Four very popular Planetarium programs are addressed in this Appendix There are certainly others but these provide a good cross section of the basics But first a generic look at what is done Generic Approach The overall approach is to use the configuration tools in the Planetarium Program to select a specific telescope to connect to In this case you would select an ASCOM telescope Then you would use the Ascom Chooser screen that comes up to select WHICH ASCOM telescope you want to connect to and at this point you would select SITECH A window may come up after that that allows you to click on Prope
218. lt E gt To read the current output status issue the command XXQ lt E gt response will be 0 1 2 or 3 When the outputs are on the associated inputs will read a 0 The outputs are open collector sinking current 10 12 AUTOGUIDER PORT There is a 6 position modular jack which has the 4 digital inputs for the autoguider port This is set up to work with an SBig camera The inputs normally float high and to guide the associated pin is pulled low See appendix C for the pinout 10 13 RADIO HAND PAD AGENCY APPROVALS FCC This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on
219. m They are 3 different colors so you can easily see the current mode with a quick glance at the receiver The fourth LED flickers whenever the receiver receives a valid signal from the handpad transmitter 133 of 236 Slew LED This Red LED is on if the handpad is in the slew mode Pan LED This Yellow LED is on if the handpad is in the Pan mode Guide LED This Green LED is on when the SiTech Controller is in the guide mode The LED is on medium brightness if the controller is in the guide mode but it is on brighter when there is a guiding signal present When the controller is in the guide mode guiding pulses can appear on the external Guide port or the handpad arrow keys however the LED only gets brighter when a guiding signal is on the guide port Whenever a guide signal is present on the guide port the receiver will put the SiTech Controller in the Guide mode To exit from the guide mode press the middle SPD button Servo Version 1 6 or later If the receiver is used on a Mel Bartels Stepper system the Guide mode LED only illuminates when a guide signal is received The receiver only assumes that the Stepper system is in the guide mode Receive LED This Red LED flickers brightly each time a valid radio signal with a valid address and valid checksum is received It flickers faintly if it receives a valid signal with the wrong address 10 4 5 Setting Address To select the address of the transmitter hold down the ALT ke
220. m and maximum displayed levels by moving the two sliders underneath the histogram To zoom in to the histogram drag a zoom frame by holding down the left mouse button The button labeled vvvv allows access to search parameters that were hidden because the program was run from the command line Interacting with SiTech If the SiTechExe process is running PlateSolveXP will use as the initial guess the current RA and Declination of the telescope by pressing the Load button Pressing the Sync button sends the coordinates of the computed image center to SiTech for use as a calibration point Version History Version 1 07 2009 07 11 Version 1 08 2009 07 18 Open output file as late as possible References 1 http adsabs harvard edu cgi bin nph bib_query 1995PASP 107 1119V amp amp db_key AST 208 of 236 Appendix J CalPointsXP CalPointsXP by Dave Rowe Version 1 09 2009 07 11 CalPointsXP creates an ordered list of azimuth altitude pointing directions above a userdefined local horizon These calibration points are typically used to create a telescope pointing model by successively slewing to the pointing direction taking an image performing a plate solve and passing the center coordinates of the image to a telescope modeling routine such as PointXP The Horizon File CalPointsXP requires a horizon file The file must be an ASCII text file of the form Az1 Alt1 Az2 Alt2 Etc where Az and Alt are the azimuth and al
221. m line is the attachment of the gurley to the axis must be as mechanically accurate as you can make it or you may be introducing errors that the software will think it needs to correct since it has no way to know if they are real or you introduced them with your mounting There is more information and examples of mounting high resolution encoders in the SETUP Manual Also in the SETUP manual Appendices is information on an encoder testing routine named ChucksLogger exe that Dan Gray wrote that allows you to log Sitech motor and mount encoder data to assess your encoder performance There are also recommended test procedures to run using ChucksLogger that will show you errors that may be present from mounting inaccuracies 7 2 Gurley Internal Errors The encoder disk has 5000 lines for both the 320 000 tick and the 500 000 tick encoders The 5000 lines are read in quadrature so they effectively become 20 000 ticks per rev So the spacing between each of the 5000 lines on the disk get divided into 4 parts In addition each of those 4 parts is further subdivided into either 16 divisions or 25 divisions depending on whether its a 320k or 500k encoder That final division is done using a routine called Interpolation The problem we discovered is this interpolation routine while dividing each of those 4 quadrature parts into 16 or 25 smaller parts each of those smaller parts are not of an equal size That s the bad news The good news is t
222. maller RJ 11 port Placing a piece of electrical tape over the RS 232 port on the Sky Commander will prevent inadvertently using the wrong port 2 5 3 Setup Sky Commander for use with SiTech Controller The XP4 version of the Sky Commander is required for use with SiTech systems At the time of the writing of this document firmware 5 0 2 is the current version and is used to prepare these setup instructions Earlier versions that have firmware 3 38 and lower are not supported 26 of 236 Using the Sky Commander to perform GOTO operations with your telescope is easy but there are a few specific steps that need to be taken to get it working well The following procedures were contributed by Randy Pufahl thanks Randy To set up the Sky Commander for use with SiTech it is necessary to program the flash memory settings that remain in effect from session to session with information such as the communication baud rate encoder info and of course whether it is to work with the Sitech controller There is a special startup procedure to put the Sky Commander into this mode where these values can be viewed entered and saved While pressing the up and down arrows turn the Sky Commander on Below is the configuration startup procedure that allows changing the settings After the settings are entered and saved they remain in effect until changed from within this mode even if the Sky Commander is powered off or had the battery remov
223. ments you will have to enter a value of zero in the local search distance and speed parameters To perform photography it may be necessary to enter the guide mode This is done by holding down the top right key then pressing the right key Now the speed changes by adding or subtracting the guide rate from the current rates To revert back to the normal mode hold down the top right key and press the right key again This feature only works with the new handpad This will be un necessary if you are using a radio handpad receiver as in this case the SPD switch on the transmitter will toggle between Slew Pan Guide modes If you are using an auto guider as soon as the guider commands are sent to the controller the SiTech is automatically set for guide speeds 2 3 3 Observing the Crab Pulsar Here is a Challenging Idea If you have or have access to a very large aperture telescope 28 inches or larger you may be able to see the crab pulsar blink Here s how Obtain a servo motor with encoder that is able to run at least 1 800 RPM you could connect this motor to a servo controller and put an interrupter on the shaft of the motor a circle with a pie shape cut out of it balance the interrupter and hold this assembly between the secondary mirror and the eyepiece while running at somewhat less than 1800 RPM You may be able to see the pulsar wink in and out To test this out you may use one of the LED s It winks at the same frequency of the crab
224. modeled the more accurate Sitech will know where the telescope is actually pointed This will result in dramatically improved tracking and GOTO accuracies Bring up the window to see it now just to see it but information on it will be covered in the Advanced Features section Click on Okay at the bottom of the PointXP window to close the window Make learning about PXP one of the first Advanced Features you learn about once you have the basics down 4 3 4 Park UnPark SetPark Below the Controller Mode Window are three buttons labeled PARK UnPark and SetPark These let you move the scope to a position you want to park it in and stop tracking so it stays at that position and then tell the scope to memorize that position by clicking on the SetPark button Obviously you need to have the mount initialized prior to all of this so it actually knows where it is We will cover how to initialize the mount soon Also when you click on Set Park if you have any PointXP Cal Stars loaded which are used to calculated the model of your mount that improves its GOTO and tracking accuracy it will save them to disk When you click on UnPark it will load this file again so your telescope model will be in effect Assuming the mount was initialized and in the position you want to park it in and tracking was turned off and you clicked on SetPark to memorize that position now you actually need to tell the mount to actually Pa
225. ms Init Altitude 141 19 03 AltOtfset Altitude Offset Cale Only OffsetsiAbgn ampe Keep Window Offset Init UplMarual automatic 86 esrop ok Cancel Conte n27 sacl GEM Scope is looking West C GEM Scope is looking East Help Colors 9 2 Star TYC 3105 02070 1 18 36 56 19 18 6156070 hours Dec 38 46 58 8 38 782992 degrees Magnitude 0 1 Extinction 0 11 S Azimuth 062 33 Rises at 11 46am Altitude 40 22 Transits at 07 35pm Air Mass 1 5 Sets at 03 27am Other Names HIP91262 HD172167 1 ues Tycho Magnitude V 0 09 F Paralax 0 12893 0 00055 Implied Distance 25 3 ly 0 1 E Proper Motion RA 0 2010 Dec 0 2875 Ki Galactic Longitude 67 45 zi Center Scope Sync Scope Copy Center Object Place Target Notes ji im Web Search lt so e Cancel Next 1 2008 08 26 20 35 RA 184 982 Dec 1384957 Azim 062 AR 404 Precess_ No I Notice that the star we clicked on in this example is Vega also named TYC 3105 02070 1 in the Tycho Catalog A small cross is placed on the target where we clicked The small information screen has three buttons that can be confusing e Center Object Puts the object you clicked on in the exact center of the screen e Center Scope Sends the GOTO Command to Sitech however the mount must be initialized first so it knows where it is so then it can know where to GOTO e
226. munication cable so the SiTech Ascom Driver can communicate with both controllers at once Pinouts are in the SETUP manual appendices You will need to mount a small servo motor with a timing belt or gear to your focuser for this to work To be able to use the Temperature Compensated Focusing TCF capability which automatically corrects for thermally induced changes in focus you will need to build a simple temperature sensor circuit that plugs into the AUX port on the focuser motor controller This circuit is in the circuit schematics appendix in the SETUP manual To improve the repeatability accuracy of the focuser its recommended that you also add a Zero Position Init Sensor It can be part of this same circuit and is shown on the same schematic Even if you do not use the TCF routine itself the Zero Position sensor is a very worthwhile addition to your motorized focuser The units in the controller for the focuser are ticks per Inch or ticks per mm Use ServoConfig and change the address of the second controller to 3 set up the Slew fast speed and Pan Slow Speed and Guide Speed Guide Speed is only used if you install an absolute zero Init sensor it should be slow enough so that the focuser moves less than the scope s depth of focus during one read controller cycle typically 0 2 to 0 5 seconds and the Ticks Per Inch or mm then you re ready to go Next in the SiTech configuration menu click on Use SiTech Focuser
227. muth 3 How fast the slew setting should be 4 How fast the pan speed should be 5 Optional Latitude of the observing session For details on how to set up your system to use Drag and Track mode refer to the SETUP Manual in the AUTO TRACKING TAB Dialogue section When you calculate the encoder ticks it s important to understand the resolution of your encoders Generally speaking the effective number of ticks is 4 times the resolution of the encoder This document uses the effective encoder ticks unless otherwise stated If your encoders have 2048 as part of the part number the encoder wheel has 2 048 lines on it The effective encoder ticks will be 4 times this or 8 192 Using the ServoConfig software and the Edit Parameters button be sure all of the motor and encoder ticks per revolution are set properly in effective encoder ticks Also be sure that the Right button on the handpad moves the scope clockwise looking down and the Up button on the handpad moves the telescope up If not change them using the features of ServoConfig Now select the Auto Tracking tab Now click on the DragNTrack radio button It would be good but not absolutely necessary to enter the latitude of your observing site which is also on the Auto Tracking tab For the DragNTrack to work properly it s important to note that the UP handpad key needs to move the telescope up in altitude and the RIGHT key needs move the telesco
228. n Wait is in progress you can terminate it and keep going by pressing the Top Left Button ESC More info When panning keep in mind that the communication loop time becomes critical for accuracy What happens is at the beginning of a Pan a goal is set for the longest moving axis The telescope is told to go farther than this goal but the position is checked and when it gets there it now performs the next move so the nice thing is it s a seemless move no stopping then re starting The bad part is by the time the software knows it has moved far enough it s possibly moved too far because of communication lacency There are about 3 things you can do to improve the accuracy 1 Pan slower 2 Pan faster but just before the next position where you want to change directions put another shorter pan at a slower rate 3 Use a faster Communication loop time in the SiTech Setup window Have fun 95 of 236 5 2 5 Controller Stuff You can set the Motor Encoders to the value of the Scope Encoders or vice versa using this window You can also have a look at many controller internal parameters and also there is a terminal mode for direct access to the controller Except for updates sent to and saved to the controller using the Terminal Window any changes made using this window are only made during this time that this session of SitechEXE is active and are not otherwise saved to the controller However it IS a convenient way t
229. n ever increasing speed till I powered it down I am not sure if my switching those cables caused this problem or not Solution Yes swapping motor power cables or encoder cables will cause one motor to run away at high speed Don t feel bad I ve done this more than once Fix hook up cables properly re synch the scope position consider attaching small labels to the cables since they all look pretty similar Handpad Operation Troubleshooting Problem I m using an old style handpad the one with a center switch and the scope only moves in two directions instead of 4 Solution Check that the internal jumper is set properly for the old handpad Problem Some of the switches don t work properly 188 of 236 Solution Use the ServoConfig software At the main screen look at the virtual handpad Pressing each handpad button should make the appropriate virtual button highlight If not check the handpad for problems If the virtual handpad works properly check the slew and pan rates Radio Handpad Troubleshooting Problem There are no LED s on when the system is connected to the scope controller Solutions Check the modular cable This must be a 6 conductor flat cable with pin 1 connected to pin 1 Many modular cables connect pin 1 to pin 6 2 to 5 etc Check that the jumper is in the proper mode for your system Stepper vs Servo On the Servo controller check that the jumper next to the handpad button is in the proper position It m
230. n the SiTech Ascom driver Forgot to write this but I m assuming it was in 0 33 where I used the new polar align routine and only pay attention to the Ist two stars FAS FAS FAC 2g 2g 2g E E K K FAS K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K FK K K K K FK K K 0 32 Fixed PECGraphLines freaking out on overrange Fixed Tracking Button to display better Fixed Declination hunting if you ve backlash controller and ascom driver Fixed using the wrong ticks per rev in the update encoders window johnM found the bug EEEE E E E E K K E K E K K K K k K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2 K K 0 31 Made GetString window bigger so textwrap wouldn t make text disappear Made script wait time be in seconds instead of millisecs Got rid of wp troubleshooting window Starting on Offset Moving after clicking on Polar align Fixed Virtual Keypad Clicking Fixed Scope2Motors and Motors2Scope Added Focuser Park and Rotator park to the park commands setPark Park Unpark 224 of 236 HUGE Found trouble with AltOffset routine had to lower the window for finding the wrong solution if below above equator Also had to see the size of the change and also add if the polarity changed When clearing inits we now perform an offset init Fixed Track On Start Configuration Bug On non initialized open of init when init point is loo
231. name in a PanRel script then take an exposure during the pan using a bright star and a piggy back camera You will then have your name writen with a Star One more idea would be to use a relatively fast pan rate and sweep the areas that aren t patrolled by the survey telescopes in search for comets This would require a relative script because then you could search the same relative areas of sky instead of absolute areas of sky Procede in a manner similar to this 1 Move the telescope to the start position if this is the moon use the edge of the terimator for example 2 Click on Add Anchor 3 Click on Add While This will keep the script from creeping as the Anchor will only be done one time because the Loop command will skip the Anchor command since the While label is after the Anchor command 4 Move the telescope to the next position 5 Click on Add Pan Relative Enter the time in Deg s per second as desired 6 Repeat Steps 4 and 5 as necessary 93 of 236 7 If you want to end exactly where you started your last movement command should be PanToAnchor Here s an example of a PanRel script Anchor While PanRel 00 02 12 00 09 21 0 06 PanRel 00 00 01 00 37 03 0 06 PanRel 00 03 58 00 31 15 0 06 PanRel 00 00 08 00 30 57 0 06 PanToAnchor 0 06 Wait 5 Loop NOTE The Anchor command should only be used if you are using the PanRel command It would be better to just use a Slew at the beginning to g
232. nce done should stay the same for a particular controller This should be done before making an accurate PointXP run if you re trying for sub arc minute pointing Motor Operation Troubleshooting Problem When power is applied to the SiTech controller and a handpad direction button is pressed the motor slowly increases faster and faster until it s full speed Solution The motor encoder is not supplying feedback Check cabling connectors and encoder you can swap the altitude and azimuth motors for testing See if the problem follows the motor or if the problem remains If the problem remains there may be an issue with the controller If it follows the motor it is definitely a wiring or encoder problem Problem Motor runs away as soon as power is applied or commanded to move After running 187 of 236 fast for a short time it stops and the light flashes Solution The motor encoder relationship to the motor polarity is wrong See section on Setting Up the Motors Problem When commanded to move the motor starts ramping up then stops and the LED flashes Solution It could be that you are using higher voltage motors with only 12 volts applied to the controller Either slow down the speed or use a higher voltage on the power to the controller Problem Nothing works at all and the two LED s are on very faintly Solution There is a major problem with the CPU If you were using version 1 3 or earlier there was a bug that a
233. nd H is hours If the file format is FITS and the FITS header file contains the image center OBJCTRA and OBJCTDEC keywords then PlateSolveXP will enter that image center for you 3 In the Parameter form enter the approximate size of the image Toggle between arcminutes and degrees by clicking on the units button Typically the image size can be in error by as much as 15 and the program will still be able to find a plate match 4 Click on Plate Match The program will estimate the image background and subtract it from the original image It will then extract the brightest stars having statistically reasonable size and shape It will then attempt a plate match by creating a catalog around the approximate image center and comparing this catalog to the extracted stars It performs this comparison by matching triangles in the image with triangles in the catalog If triangle matching is successful the program will add and remove stars from the match until the error in the Affine transformation between image and catalog satisfy a strict set of matching rules including proper geometry and overall fit error If the program is unable to match the image using this local catalog it will perform a spiral search If the number of regions searched exceeds the Search Limit the program will terminate The current search center is displayed as the search progresses 5 Inspect the match in the Display form Extracted stars are denoted by a red cross cata
234. nd YEL display Added UFN command to upgrade the flash alternative to handpad Version 1 2 7 24 2004 added the XNT command which stops the scope then and starts tracking Version 1 3 8 7 2004 fixed every other fastest limit bug added stopped equatorial rate when a speed command ascii or motion command pic servo 0 FIG 2g 2g E K E K K K K K K K K K K K K K K K K K K K K K K K Version 1 4 Changes Changed Loader routine to Ist three blocks Changed loader routine to ignore Ist three blocks erasing or writing Now if you try to write to blocks 0 1 or 2 it returns good but doesn t write Before Erasing block during upgrade double check it s not block 0 1 2 in case of sparatic execution Detect if Track routine installed and if not flashes both lights for 15 seconds before running servo program Spit out startup serial string don t revert to slew speeds when letting up slew or pan buttons stop instead estop hold the speed switch in for more than 2 seconds new handpad only 230 of 236 made interrupt vectors absolute added all interrupts that could possibly be used disable interrupts and watchdog on flash write on save of flash stop the motors if platform goal greater than abs 4 194 303 we disable re wind and stop Fixed pic servo timeout disabled the ascii communication Put code at address 512 that catches erasure of block zero sif it is erased it re programs bl
235. nd their coordinates See appendix C in this OPERATIONS Manual for the format for a database file 4 6 2 Select File Line Once you have a database file loaded this button allows you to select a line in the file to select the object on that line If the database file is long enough you will see previous reverse buttons on the selection screen to scroll forward backwards through the file When you select a target it will appear in the window on the GOTO Tab The targets coordinates appear below the window with the name You also will see the Alt and Az of the target appear below the RA Dec information 4 6 3 Star and Messier buttons You can directly go to the namedstars dat file by clicking on the Stars button or the Messier dat file with the Messier button 4 6 4 NGC and IC windows Below the Star and Messier buttons there are two windows that you can put the cursor on and enter an NGC number or an IC number directly and hit Enter to pull up that target directly NOTE The database files for the NGC and IC targets were obtained from http ngcic org which has now changed to http www ngcicproject org default htm Some users have reported slight errors in the RA Dec in these files If you find any errors please make note of them and Let Dan Gray know 4 6 5 GoTo and Sync Buttons Once you have a target loaded if the telescope has been initialized you can simply click on the GOTO button and the mount will slew to that selecte
236. ndix in the SETUP Manual Use high resolution encoders on the mount Automatic Interpolation Error Correction for sub arc second tracking using 320 000 tick or 500 000 tick Gurley encoders is also provided When used on an Equatorial mount periodic error in tracking is virtually eliminated using these high resolution encoders When used with Alt Az mounts slippage and periodic error in the drive trains are virtually eliminated Park and UnPark can be used to retain sky alignment from session to session A repeatable park position alignment either by optically sighting on a target or using a precision level on a GEM balance shaft and scope and accurate time on a PC can allow immediate slewing to targets after startup Scripting can be used to plan and run a night s observing session or even run the mount remotely Using a PC SiTech exe has a script building application you can use to make and run 12 of 236 the script Polar Alignment of an equatorial mount can be quickly accomplished with the PC application built in to SiTech exe Built in Simulator capability of SiTech exe automatically senses if there are no servos connected and operates with the message Faking Servos in the message window This powerful feature allows you to learn and test the controller system along with Ascom connections to other software such as TheSky Earth Centered Universe Cartes Du Ciel Maxim Pempro Elbrus and many other programs Built
237. nect to Telescope If a setPark Park WAS done in previous session Click on UnPark No further inits required Ready for GOTOs after UnPark If a SetPark was NOT previously done Perform an Offset init to get tracking started Initializations For details reference sections 4 7 4 8 and 4 9 NOTE If you are going to do a drift align for an equatorial mount only do a single offset init initially to get tracking started Then do your drift align then return and do another offset init or your calstar inits for mount modeling No Planetarium Program Connected use internal Sitech database Use handpad to center telescope on target On GOTO Sync Tab in Sitech select target For a Star Click on Star Button Click on star s name to select it Verify star name and coord in windows For a Messier Object 195 of 236 Click on Messier Button Click on object desired Verify object name and coord in windows For an NGC or IC Target Type in target number in appropriate box Hit Enter key Verify target s name and coord in windows For an object in a database file Click on ScrollFileName Select database file desired and click on Open Click on Select File Line Click on object desired and hit Enter key Click on Sync For GEM VERIFY Looking East or Looking West Verify type of init when Init Window opens default is Offset Stop timer with left button if desired If timer was stopped click on type of init then on OK
238. ng For instance TheSky has that option Also Sitech always sends its coordinates back to the planetarium program fully cooked This can be a source of error for the cursor location if the planetarium program expects to receive J2000 uncooked coordinates In addition nutation and precession corrections can be done in the planetarium program or in Sitech Sitech DOES have the option to turn that on and off so make sure you only do that once either in your planetarium program or in Sitech And finally refraction correction can be done in Sitech or your planetarium program Again only have one or the other do it For slews there are two different ways for programs to send the ASCOM slew command One is simply SlewTo and the other is SlewToAsync The SlewTo command will not have SitechExe return its position till the slew is completed so the cursor will not move till then The SlewToAsync reports its position during the slew so the cursor will move across the screen as the scope slews Use the Async option if your program allows it After being initialized simply click on a star to GOTO and select move scope or GOTO in your planetarium program and sit back and enjoy watching the scope move to your selected target 158 of 236 Earth Centered Universe ECU ECU is a very popular powerful telescope control planetarium out under the stars reasonably priced program and is very easy to use for a Its strength is it
239. ng ServoConfig manually point the telescope toward the Western horizon Make sure pressing the up arrow moves the scope North and the encoder counts increase If this is not correct change the direction using the appropriate Invert button s To change the direction be sure and change both the motor and the motor configuration to the opposite of what they are 2 Make sure that pressing the right button moves the telescope even more west goes towards below the horizon if still looking at the western horizon and the encoder counts for AZ RA increase If this is not correct change the direction using the appropriate Invert button s To change the direction be sure and change both the motor and the motor configuration to the opposite of what they are 4 13 2 Set Up and Operation in Southern Hemisphere Setup and operation in the Southern Hemisphere requires the mount to move in the opposite direction compared to the Northern Hemisphere The following steps will allow use of SiTechEXE in the SH with current versions before SiTechEXE054H Starting with version 054H these steps should be unnecessary However be sure the Declination is set NEGATIVE to indicate to SiTech it is in the Southern Hemisphere So here are the steps to follow 1 While using ServoConfig Manually point the telescope toward the Western horizon Reset controller Make sure pressing the up arrow moves the scope SOUTH instead of NORTH which is in the m
240. ng here If you want to know what you re doing study the following ASCII protocol commands that are listed in Appendix E of this OPERATIONS Manual and you can see just what the controller can do Have fun 97 of 236 5 2 6 PEC Control Sitech has a built in and very capable tool to record Periodic Error either with an autoguider or via handpad inputs as you viaually observe and correct the PE and to program the controller with this information to eliminate this uncommanded motion for the RA axis of an Equatorial Mount currently it only works for equatorial mounts not for Alt Az mounts It is only as accurate as your inputs are so it allows recording several runs and averaging and smoothing them Alternatively you can also use the outstanding PEC correction routine PemPro by CCDWare SitechEXE has a custom interface to PemPro that makes using PemPro very easy This should probably be the first of the Advanced Features to come back to unless you are using a high resolution encoder like the 320 000 or 500 000 tick Gurley encoders The reason is excessive PE can degrade using PointXP to model your mount If you ARE using high resolution encoders 8192 encoders are NOT considered High Resolution then do not use this capability PEC is Playing 174 124 03 04 Cntr Buff Status Loaded 10 Are Seconds x Use Auto PEC Syne Iv Clear Collective Show 5 Collective Items M Clear PEC Table in Controller Loa
241. ng is for doing initializations and then slew the scope to those locations and take an image Then PlateSolveXP will solve for what the coordinates are for the center of that image and use that to perform a Cal Star Init Then move on to the next star etc All automatically while you simple stare in amazement The screen grab below shows the CalPointsXP screen on the right and the PointXP screen on the left with the SKY graphic selected via the SKY Errors toggle button in the lower right area of the PXP screen The SKY display shows the location in the sky of the CalStar Init points that have been taken Notice they are exactly the same as CalPointsXP selected and input into the automated script that was built Also notice the yellow cursor in the CalpointsXP screen that shows the current position of the telescope and the small circle in the PXP graphic that shows the same thing 81 of 236 CalPointsXP 1 09 C Program Files Common Files ASCOM T jek PointXP By Dave Rowe Incorporated by permisson Terms to Include in Model IV Cone Z2 Hub 21 W Dec Imbalance I RA Imbalance M Dec Transverse M RA Transverse I Dec Droop cos J Dec Droop sin I Alt Sin 2 Phi I Alt Cos 2 Phi T Alt Sinf3 Phi Alt Cos 3 Phi AltEncO 360 00 00 AzEncO 359 59 59 00 20 39 00 04 56 00 00 13 00 04 26 00 00 36 00 00 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Read Config Write Config Clear
242. not matter To edit the vbs file you have to right click on it and select edit If you doubleclick on it you will actually run the script Now to use this capability the night before make sure your scope is properly initialized and your GOTOs are accurate Then slew the scope to the stationary target center it and turn off tracking Click on the NUMBERS tab and write down the ScopeAz and ScopeAlt numbers Now the hardest part you have to convert them from DD MM SS to DD DDD I leave the math to you Now edit your script file right click edit and change the data in the line that reads Scope SyncToAltAz ddd ddd ddd ddd The azimuth decimal degrees data is the first number and the decimal degrees altitude data is the second one NOTE In case you noticed yes the term SyncToAltAz has the term Alt before the term Az and yes the order the data is written has the order opposite to that with the Az data first followed by the Alt data If you did NOT notice shame on you You are not reading this Don t forget to save the edited script Now the next day Manually slew the scope to your stationary object and make sure tracking is stopped Double Click on the script file to call it up and run it This will call up the Sitech Synch Screen Do an Offset Init and you should be good to go 56 of 236 4 10 CONFIG TAB The Configuration Tab displays the critical information SitechEXE needs from th
243. o your mount modeling using the Point XP modeling tool NOTE Taki was the originator of this method of initialization and it was published in Sky amp Telescope in the late 80 s Dan converted Taki s BASIC program to C for his stepper system and then to C for the ASCOM driver When you do the matrix math of the Taki method the latitude and longitude can be pulled out of the matrix and that is what is shown on the Init screen These should agree to within a degree or closer if you are using an accurate and level Alt Az mount If you have an equatorial mount the latitude should be close to 90 degrees and it will probably read the amount of deviation from 90 which is your polar misalignment 53 of 236 4 9 THINGS TO KEEP IN MIND 4 9 1 First Two Stars Your first two stars are absolutely the most critical entry stars For superior accuracy use a crosshair eyepiece or a ccd camera with a crosshair on the screen if possible You need to have as wide as possible azimuth alt az scopes or right ascension equatorial scopes and as close as possible in altitude Alt Az scopes or Declination equatorial scopes If you have an Alt Az scope you can use Polaris as your first star and then another star with roughly the same altitude 120 deg s away Do not use a star at the zenith for an alt az scope If you have an Equatorial scope non GEM choose two stars about 90 deg s apart near the celestial equator For best
244. o Pin 6 AlPotR1 2164 This is the resistance of the resistor that s in series with the potentiometer AlPotRes 1831 This is the resistance of the potentiometer itself AlPotAngle 345 This is the angle that the potentiometer can measure Most potentiometers can only measure about 300 deg s The pots I mention in the schematic can measure 345 deg s AlPotWindow 15_ This is the window size of the comparison between scope position and potentiometer position degrees If the scope position moves out of this window then it will shut down the scope AlPotOffset You can zero the pot position with this number AlPotVoltRef 2 4 This should be set at 2 4 volts It s best to actually measure the resistance values and enter them in the configuration The same configuration names apply to the azimuth RA but start with Az instead of Al Once you ve entered these values in the SiTech cfg file you need to mechanically adjust the potentiometers Follow these steps 1 First set the AlPotOffset and Azimuth to 0 0 in the configuration file Run SiTechExe and click on the Features tab then Controller Stuff 2 Make sure your scope is initilized at least roughly 3a Point your GEM mount so the counterweight is down and the scope is pointing north 3b Point your Regular Equatorial mount so the fork is level looking at the meridian and move the scope to point north 90 deg s declination hour angle of 0 0 3c Point your AltAz
245. o Scope Encoder Location Set Scope Encoder Location to Motor Location Set Scope Encoder Location to Motor Location RA or Azimuth Scope Encoder 00 00 00 Dec or Altitude Scope Encoder 00 00 00 Use Raw Numbers I Use Focuser Rotator HELP Dismiss Azimuth RA Pot Angle 99 Altitude Dec Pot Angle 81 Set Angles To Pats Controller Data Hover mouse over Textbox for info Fimware 0 0 PriPwM SecPwM PriE tror Supply Volts SecEtrar Prim otCur CPUTemp SecMotCur M Terminal Windows ooo o ___B AMotor Ticks Change Motor Ticks ___B AMotor Ticks Change __Dec Motor Encoder Ticks Change _ Motor Encoder Ticks __Dec Motor Encoder Ticks Change _ R A amp Scope Encoder Ticks Change Dec Scope Encoder Ticks Change Except for updates sent to and saved to the controller using the Terminal Window any changes made using this window are only made during this time that this session of SitechEXE is active and are not otherwise saved to the controller However it IS a convenient way to temporarily 45 of 236 make a change to assess its effects You do not normally have to access this window for normal operations so the details of using it are in the Advanced Features Section 4 5 5 PEC Control ADVANCED FEATURE Sitech has a built in and very capable tool to record Periodic Error either with an autoguider or via handpad inputs as you viaually observe and correct the PE and to program the controller w
246. o a Sky Commander XP4 computer for GOTO functionality without being connected to a PC If you want to use Sky Commander with a SiTech controlled mount you will need to have Sky Commander XP4 with version 5 02 of SC software Your SiTech should have firmware version 3 3C BIN or later The telescope encoder information comes from the Sidereal Technology Servo Controller instead of the encoders themselves There is only one cable connected to the Sky Commander and it is the Serial Cable See Appendix E in the SETUP Manual for the cable diagram If you don t have telescope encoders not to worry because you can select the SlewNTrack mode of operation and now the encoder information will come from the servo motors not the telescope encoders Also if you do use telescope encoders they will be powered from the Servo Controller power thus the Sky Commander batteries will last much longer 2 5 1 Set Up SiTech Serial Port The SiTech controller RS 232 port is used for both connecting to a PC for setup with ServoConfig as well as later connecting to the Sky Commander You need to set both the Sky Commander and SiTech Controller to the same 9600 baud rate The easiest way to set the baud rate for SiTech is to use the Terminal Window in ServoConfig You can issue commands like this without doing anything else type SB1 where SB Set Baud Rate 1 9600 2 19200 When you connect the Sky Commander RS 232 Serial Communications cabl
247. o file Focuser Calibration in the SiTech directory It will over write any old data If you wish to keep old data be sure to read it in before clicking the Write Stars button then new data is added to the old data beware of the NOTE however in the next paragraph The Read Stars button reads in prior nights data from the Focuer Calibration file NOTE these points are valid ONLY if the absolute positioning is exactly correct Typically this means that an absolute zero position sensor must be used to get the accuracy needed 122 of 236 You may delete all stars from active memory by clicking the Clear All Stars button The Focuser Calibration file is NOT deleted The data plot is zoomed around the data points so the lower left corner is NOT 0 0 The temperature axis increases to the right the Position axis increases going up 8 2 8 Miscellaneous Focuser Notes When using the window buttons and handpad to move the focuser the fast speed corresponds to the slew speed in ServoConfig and slow corresponds to pan The slowest guide speed is only used for the final approach to the absolute zero position sensor in its automatic routine The guide speed should be set slowly enough so that the focuser moves less than the scope s depth of focus during one read controller cycle typically 0 2 0 5 seconds This can cause a slow initialization but is necessary for accurate focusing The abs
248. o record your pec tables 2 Use the guide mode and your handpad to manually guide while recording 3 Use Pempro and then import your Pempro file 5 2 7 Simple PEC Recording Session A simple recording is just recording a single worm cycle It assumes your periodic error is very repeatable Here is what you might consider doing for a simple session assuming motor ticks per worm revolution is programmed Note It s a good idea to clear out the PEC curve in the controller before you record a new pec curve Use the PECGraph page and click on Clear Pec Table In Controller 1 Select the PEC screen from the SiTech ASCOM driver 2 Select whether you have an automatic PEC sensor or not at the left side of the screen 3 Start guiding on a star either manually or with an autoguider 4 Click on the button labeled Arm PEC Record e If you have an automatic PEC sensor wait for it to line up and recording will start automatically e If you don t wait for the worm to line up with your reference and press the top left button on the handpad 99 of 236 e When recording is started you will see the status textbox on the left change to Recording e During the next revolution of the worm the controller will record all of your button presses e Once the worm revolution has completed The status will go to Idle and you re ready for playback e If you have an automatic PEC sensor wait for it to line up and playback will start automatic
249. o temporarily make a change to assess its effects aD Controller Stuff Controller Information Window Colors R24 or Focuser Dec Altitude Rotator or Focuserll RA or Azimuth Motor 00 00 00 Dec or Altitude Motor 00 00 00 Set Motor Location to Scope Encoder Location Set Motor Location to Scope Encoder Location Set Scope Encoder Location to Motor Location Set Scope Encoder Location to Motor Location RA or Azimuth Scope Encoder 00 00 00 Dec or Altitude Scope Encoder 00 00 00 Use Raw Numbers I Use Focuser Rotator HELP Dismiss Azimuth RA Pot Angle 39 Altitude D ec Pot Angle 81 Set Angles To Pats Controller Data Hover mouse over Textbox for info Firmware 0 0 Supp Vols SecPWM PriE tror Supply Volts SecEtror Prim otCur CPUTemp SecMotCur M Terminal Windows pt ___B AMotor Ticks Change Motor Ticks ___B AMotor Ticks Change __Dec Motor Encoder Ticks Change _ Motor Encoder Ticks __Dec Motor Encoder Ticks Change _ RA Scope Encoder Ticks Change Dec Scope Encoder Ticks Change PriP WM Motors and Encoders The top part of the controller allows you to have a look at the current values for the telescope angles according to the Motors and also according to the Encoders You can also update one to the other or vice versa with the buttons You can view in raw numbers by checking the Use Raw Numbers checkbox You can view the Focus Rotator controller if you ve enabled i
250. o zero The 8 terms you want to change to be equal to zero are Al0ffsetSaved AzOffsetSaved AlScpOffsetSaved AzScpOffsetSaved AlScpGurl0ffsetSaved AzScpGurl0ffsetSaved EA1LOFFsetSaved EAzOffsetSaved Then save the file and re start Sitech and your planetarium program You will have to do your inits over but the digital lobotomy you just did on Sitechexe should have cleared up its confusion GOTO and Tracking Troubleshooting Problem After powering every thing up unparked the scope synced on a nice bright star commanded the scope to slew to a target and it went there perfectly Then I went to tweak the computer clock to a more accurate time and noticed it was not set to DST so I upped the hour by one Went back to taking image exposures for stacking and the images were trailed The scope was tracking but in the wrong direction Solution If you simply put the clock ahead one hour it s going to think the position is one hour off and will try to track there I m surprised it didn t slew there instead but I m sure this is the problem You need to instead tell the computer it s daylight savings time this will automatically move the clock ahead but SiTech will know its daylight savings time and make the appropriate adjustments 182 of 236 Problem I have a new installation of SiTech and can t get accurate slews I m sure the ticks are set correctly and the motors go in the correct direction What should I chec
251. ock zero Put code at address 1024 that catches erasure of block one sif it is erased it re programs block one 0 IS 2g 2g E K K K K K K K K K K K K K K K K K K K K K K K K K z Version 1 5 Changes Added command SB Set the Baud rate 1 9600 2 19200 allows use of Q emulation programs that won t allow 19 2kbaud deleted version 1 4 spit out startup serial string add keystatus to the standard return string test XXR Add Command that sends two locations and two speeds at once Must send 20 bytes after the XXR lt e gt that mean this 4 bytes X destination 34 bytes X Speed 4 bytes Y destination 4 bytes Y Speed 1 byte bit 1 means use following xbits and ybits value if zero ignore 1 byte xbits 1 byte ybits 1 byte checksum If data recieved properly the controller sends the new binary send info XXS Add command that returns the new binary send info 4 bytes of Alt motor position 4 bytes of AZ motor position 34 bytes of Alt scope encoder position 4 bytes of Az scope encoder position 1 byte of keyboard status 1 byte for Xbits 1 byte for YBits 1 byte for some stuff Bit 0 1 Alt at destination Bit 1 1 Altitude in manual Bit 4 1 Azimuth at destination kd gt gt 231 of 236 Bit 5 1 Azimuth in Manual 1 byte for checksum Fix bug in slewntrack taking off on reset before upgrade erase patterns so a cold boot will be performed when finished smake dynam
252. ocuser x this is the position you would measure with a ruler o Absolute Position Effective Position The position corrected for 0 3905 Effective Position temperature If TCF is off the effective position equals the absolute position If TCF is on the effective position jo 0 Temp Switch sensor WA ra is the position of the setpoint the focuser is emulating FastFocus IN OUT i LC SlowFocus Temp Switch sensor the first number is the raw IN JOG OUT temperature measurement The second is either O or 4 Jog Dist 0 0100 depending on whether the absolute zero position sensor if present is open or closed HP Jog HP Slow HP Fast The top set of IN and OUT buttons move the focuser Stop Focuser continuously select Fast or Slow Temperature Comp ON Already Focused The lower In and OUT buttons move the focuser a preset Temperature Comp ON Move To Focus distance the JOG distance The Enable Handpad buttons allow the ESC and RTN buttons on the telescope handpad to also control the focuser They are disabled by the Handpad to Scope button on the SiTech scope tab window MOVE Focuser to this Setpoint H9 1755 f 0 125 1 8 0 1250 H E 0 1650 The STOP FOCUSER stops the focuser movement underway and will kick it out of TCF mode if TCF had been started Normally you will not need this button unless your focuser has become possessed and decides to go do its o
253. ogy Servo Controller in a GoTo and Tracking mode using an Argo Navis Digital Telescope Computer The Argo Navis needs to have version 1 1 6 or later installed in its firmware You can download and upgrade either or both units by visiting the appropriate website The telescope encoder information comes from the Sidereal Technology Servo Controller instead of the encoders themselves There is only one cable connected to the Argo Navis and it is the Serial Cable See Appendix E in the SETUP Manual for the cable diagram If you don t have telescope encoders not to worry because you can select the SlewNTrack mode of operation and now the encoder information will come from the servo motors not the telescope encoders Also if you do use telescope encoders they will be powered from the Servo Controller power thus the Argo Navis batteries will last much longer The first three modes do not provide GOTO capability but do provide basic capabilities like PEC if programmed into the controller and simple tracking operations which make them ideal for portable systems to simply plop them down and be able to use them Initializations are done using the handpad 2 1 ALT AZ DRAG AND TRACK MODE The DragNTrack mode is used primarily with Alt Az mounts if you would like to push your telescope by hand or slew with the handpad but don t need super accurate tracking or GoTo capabilities but would like computer less accurate tracking The DragNTrack
254. ollective The Collective has nothing to do with the Borg in case any Trekkies are wondering On the right of the Window you see some checkboxes that have to do with displaying PEC data on the line graph Under these you have some buttons having to do with files There are two ways to approach PEC in the SiTech driver one is the simple way which takes very little work and interaction and the other is the more accurate but more complex way In Order for PEC to work you MUST program the number of motor encoder ticks for one revolution of the worm using ServoConfig version 1 0 Edit Parameters Misc and Action tab Be sure to also send this data to the controller and then save to flash ROM See the SETUP manual section 8 3 7 for additional details Also if you re using Servo Controller Firmware version 3 0 with a letter after it then you may need to configure the SiTech ASCOM driver to be in the Drag Mode In version 3 0 of the Servo controller firmware the position of the motor during PEC corrections is reported and this may make the SiTech ASCOM driver try to fight the PEC corrections In version 3 1 and later this is corrected The message here is to be sure and use the most current versions NOTE If you are doing Wireless Guiding i e guiding via the ascom interface which uses the ASCOM Pulse Guide method then the Servo Controller WON T record your corrections Three solutions to this 1 Do relay guiding t
255. olute zero position sensor can toggle anywhere in the focuser s travel Depending on the sensor s position some focuser positions may be negative The program doesn t care The SET FOCUSER setpoints behave differently depending whether an absolute zero position sensor is present You really do not need to know any more about this but if you really MUST know don t say we didn t warn you So here goes If an absolute zero position sensor IS present and TCF is on they set the effective position to the setpoint position without changing the absolute position If an absolute zero position sensor IS present and TCF is off it sets the absolute position to the setpoint value If an absolute zero position sensor is NOT present and TCF is ON they use the temperature compensation data along with the setpoint position to set the absolute position If a zero position sensor is NOT present and TCF is OFF then abs Eff and you need to manually focus and then use the bottom buttons to set the focuser position in the readout window to the corresponding setpoint s value OK you were warned so if you did read it anyway there WILL be a test sent to you on this so keep re reading it till it makes perfect sense 8 2 9 External Program control of the Sitech Focuser To use an ASCOM compatible autofocus program with your motorized focuser select the Sitech Focuser from the ASCOM setup in the external program There is no configuring the focuser
256. ommand to turn off that guiding rate command If you have a comm dropout after the rate is added the rate will not get turned back off till the next comm loop and you can end up over controlling So Pulse guiding was introduced to send a guiding rate command and a time for how long to add that rate after which the rate is removed This gets around any over controlling due to comm drops These two check boxes are options for tweaking the way pulse guiding is coordinated between SitechEXE and the autoguider software Normally leave them unchecked unless your autoguider results have issues then try one or the other approaches to see if it helps 4 11 6 Setup Focuser and Rotator Tab ADVANCED FEATURE Setup SiTech ASCOM Driver V0 54L Telescope Info Mount Info Scope Encoders Miscellaneous Ascom and Troubleshooting Focuser Rotator Potentiometers Use 2 Focusers Use Sitech Focuser Use Sitech Rotator SitechEXE has the built in ability to control a second controller using one comm port and a Y 69 of 236 cable that puts both controller s RS232 connections on that single PC comm port See the SETUP Manual Appendices on how to build this cable or contact Sidereal Technology for a cable The second controller has the ability to use its two channels to control one or two motorized focusers or one focuser and one field rotator for alt az mounts Small servo motors are used and controlled just like the te
257. on in the same direction These two stars should NOT be equal distance from the meridian if you re using a non GEM equatorial mount One should be lets say within 10 degs of the meridian on one side then go down to about 40 deg s from the meridian on the other side Once the second star is added then the two windows display the proper offsets Just move your telescope mount in these directions clear all inits and add two init points again After you add the two stars you can perform a GoTo to a star This star should NOT be near the zenith or the east or west horizon Preferably a few deg s from the meridian in R A and near the equator in declination After centering on the star perform an Offset init if it s not perfectly centered Now click on the Polar Align button The telescope will move Center the star by moving the altitude and the azimuth of your equatorial mounting Once you move your mount and the star is centered then it is IMPORTANT to go to the PointXP screen and click on Clear Terms and Cal Stars This will automatically perform an offset init and drop any init points which are useless now that you ve moved your mount Repeat this process starting with loading init points on two stars at least one more time or if desired a total of 3 times Each time you will get more accurate You are now polar aligned Note Unless you have a perfect mount there s no such thing this will not be super accurate I think
258. ong with their description Faking Servos This means there is no communication with the SiTech Servo Controller The ASCOM Driver SiTechExe is emulating its presence so you can see how the driver works with your planetarium program even without the controller connected Faking Foc Rot If you have set up for controlling a SiTech Focuser or a SiTech Field de rotator or both the SiTech ASCOM driver will try to communicate with the second controller also If none is found the driver will emulate its presence also so you can see how the driver s focuser rotator routines work Reading Servo Parms Upon opening the SiTech ASCOM Driver certain parameters are read from the Controller These are the slew speed pan speed guide speed and motor and mount encoder ticks rev This message will go away when these data are read into the driver Read Rot Foc Parms Upon opening the SiTech ASCOM Driver if configured for a rotator focuser or both certain parameters are read from the second Controller at addr 3 These are the slew speed pan speed guide speed and motor encoder ticks rev This message will go away when these data are read into the driver Bad Foc Rot Communications If you have configured the driver for a focuser or rotator and there is no communication with addr 3 device i e the 2 controller this message is displayed Check to see if the controller is powered on and the RS232 plug is connected Bad Scope Commun If th
259. only the time to transfer 16 bits at a quick bit rate There is absolutely no perceived delay between when you press a button on the handpad radio or wired and when the servo motors move Can automatically track your telescope in computer less modes like the Equatorial mode for Equatorial mounts and the DragNTrack mode or the SlewNTrack mode for Alt Az mounts without having a personal computer connected When running in the computer less modes mentioned in the above paragraph you may connect a computer running just about any planetarium program and the servo controller will emulate the Tangent Digital Setting Circle protocol This allows just about any planetarium program to provide the crosshair or other indicator of where the telescope is pointed Can control a dual axis tracking platform with auto stop and then you can rewind via a handpad command and have dual axis tracking correction without having a personal computer connected Servo Motors have a FASTEST mode of operation where if the motors can t quite keep up with where it is supposed to be but it is moving in the proper direction it will not trip on position error which is the industry standard instead position error is held at the point of the position error limit This feature makes it possible to run your motors near their limit of speed and you can rest assured it will not trip on position error if your battery voltage falls a bit or the wind pushes again
260. onnected at the same time Time will tell Offsets are saved when clicking on the Config button This will allow a restart in same position if SiTech crashes OSOT Fixed altitude setting to controller for equal area panning guiding 050U Added a lot of troubleshooting stuff to try to find the crashing bug Re arranged Timers for proper operation without crashing Added Logging various stuff from configuration Added Set Process Priority to configuration Added View a scroll file and select a line Fixed date wrong in pxp file Fixed bug while changing gain in config textboxes FAS FAS 2S 2g 2g 2g E E K E E E E K E K ig K K k K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K FK K K 047 1 added option for correction of Nutation and Aberration to the GoTo Sync co ordinates 2 Changed encoder Supervisory to be DD MM SS instead of minutes 3 Working on Tick Management 4 Won t autoFindz3 until the 5th load init point 219 of 236 5 Axis rates to zero upon a stop command 6 Fixed bug in script panning never ending the pan 047B Added more lines to scripting Put exception try catch at beginning to detect for sitech process SiTech dll too Made it work from the E drive properly Deans bug 047C Added Paste button for script Made lowest loop time be 50 mSecs OR 0 0 means continuous transmit right after receive 047D Can t Set Park while tracking now Fixed meridian ove
261. ontrols gray out and Listen Mode reported on bottom left margin of Nebulosity Window If Nebulosity drops out of Listen Mode simply re run the file ListenSitech neb At the end of the PxP script Nebulosity will automatically drop out of Listen Mode 3 Call up Features Run Script window in Sitech and set the following parameters e Select how many Cal Stars to image Select at least 6 At least 16 are required to calculate all terms e Set Exposure time in seconds e Set Binning Mode o Move the script window and any other open window out of the upper left part of your screen CalPointXP and PlateSolveXP will open their windows in the upper left corner of your screen and if something else is already there they may end up being covered up 4 Click on Make PointXP Run to build script If a script already is resident in the window on the right you may get a message that asks if you want to overwrite it or replace it Click Yes NOTE Occasionally overwriting the script will kick Nebulosity out of Listen mode If that happens simply re run the file ListenSitech neb from within Nebulosity click on Edit Run Script and select the file ListenSitech neb 202 of 236 5 CalPointsXP graphic will open showing location of init points If desired to keep CalPointsXP graphic visible of init point locations click on Keep Window open else it will close in 60 seconds e NOTE You do NOT have to keep it open and if you are crowd
262. onvenient to get to my telescope I m pretty sure this used to work Now I get a bunch of error messages and a crash I launch the SiTech ASCOM driver It tells me that it can t open the serial port but I think I remember that it coped with that in the past Then I launch my customary planetarium program Cartes du Ciel and link them through ASCOM That seems to work fine The SiTech driver window cycles continuously through a series of messages Faking Servos Reading Servo Parms Bad Scope Commun Scope Parked or Tracking depending what command I ve given it That all seems fine but when I try to slew or sync it acts like it never got the command Cartes insists that my virtual faked telescope is pointed at RA 0 0 and Dec 0 0 even though SiTech says it s at for example RA 18 and Dec 42 which are normal parked coordinates Cartes gives me a message Warming SiTech says can t sync scope when not connected Then Windows gives me An unhandled exception has occurred in your application Solution You HAVE to have a serial port for this driver to work properly If you get the message can t open the serial port then the driver won t work properly So you have to have a serial port even if not being connected to the scope If you do not have a built in serial port you will need to use a usb serial dongle to create a serial port If you are just messing around without your controller and also do not have a serial dongle av
263. or between the optical axis of the scope and the altitude declination axis 2 Hub Z1 This is a fabrication error It is the error between the azimuth RA axis and the altitude declination axis 3 Dec Imbalance As the scope moves in Altitude declination the scope may flex Also will correct for a non centered encoder 4 RA Imbalance As the scope moves in azimuth RA the scope may flex Also will correct for a non centered encoder 5 Dec Transverse Same as 3 however it is as if a weight was on the side of the scope 6 RA Transverse Same as 4 however it is as if a weight was on the side of the scope 7 Dec Droop cos Corrects for the Cosine of the Declination or altitude as your secondary cage or camera flexes position during different altitudes or declination 8 Dec Droop Sin Same as 7 but the Sine instead of the Cosine 186 of 236 9 12 Alt Sin Cos These parameters can have the same effect as flattening the bottom of your azimuth axis It can help an alt az scope more than an equatorial scope Controller Stuff Menu Item Motors and Encoders The top part of the controller allows you to have a look at the current values for the telescope angles according to the Motors and also according to the Encoders You can also update 1 to the other or vice versa with the buttons You can view in raw numbers by checking the Use Raw Numbers checkbox You can view the Focus Rotator controller if you ve
264. or SlewNTrack mode may be a nice feature to use If you have a telescope of aperture 16 inches or more it may be more cost effective than a tracking platform and there are many other advantages to use the 15 of 236 dual servo controller and the Drag and Track mode instead of a tracking platform To use the drag and track mode your Alt Az telescope must have the following hardware in addition to the servo controller 1 A pair of servo motors to drive the telescope in altitude and azimuth 2 Clutches on both altitude and azimuth connected between the motors and the telescope so you can drag the telescope anywhere in the sky without damaging the servo motors Note you can use the DragNTrack mode even if you have no clutches but do have telescope encoders You will have the disadvantage of only slewing with the handpad instead of pushing the telescope by hand 3 A pair of encoders mounted to your telescopes altitude and azimuth axis s 4 A handpad 5 A 12 24 volt power supply A computer is not required for operation only to configure your servo controller 2 1 1 Setting Up the Drag and Track Mode For the drag and track mode to work properly the controller must know several things 1 The number of motor encoder ticks for a complete revolution of the telescope in both the altitude and the azimuth 2 The number of telescope encoder ticks for a complete revolution of the telescope in both the altitude and the azi
265. or offset tracking entry into the text boxes 6 Made All Red Feature 7 Made Color Choices available and saveable FAS FAS 2S 2g 2g 2g 2g 8 E E E K E K E E 2g E K E K K K K K K K K K K k K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2 K K 0 34 Fixed longitude entry bug Fixed polar alignment bug where dif between 23 and 2 hours was 21 not 3 EEEE E E 28 E K E E E E E 2g E K E K K K K K is K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2k K K 223 of 236 0 33 If ascom tracking command happens at startup it initializes the scope and unparks if parked cfg WasParked updated when parking and unparking CanUnpark is now based on cfg WasParked Made AutoGEMGoto flag and AutoGEMTrack flag Finally figured out how to specify the proper message in the exceptions Added the ASCOM SetPierSide command last ascom command I think Added all Help files Still needs editing Made figure backwards the ticks per rev with the tracking rate Adjusted the SiderealRate constant from 0 000389468194 to 0 000389425 19 Made Help Window Re sizable Added a few more things to the init reporting Added read encoders psuedo ascom commands double PriMotorEncoder bool Raw double SecMotorEncoder bool Raw double PriScopeEncoder bool Raw double SecScopeEncoder bool Raw If Raw is a 1 then it will return the number from the controller If raw is a 0 it will return the number that s been offset i
266. ore straightforward by dividing things up into categories At the bottom of each tabbed page is an OK button This will save and exit the Setup page The settings are saved in a file named Sitech cfg in the Sitech folder at c program files common files ascom telescope Sitech If you just want to change tabs only use the tabs at the top of the page otherwise you will have to click on the Change Config button again to re open the setup page 4 11 1 Setup Telescope Info tab Telescope Name and Description This area will reflect whatever you put there The ASCOM functions support these fields and this information can go inside of photo FITS headers if you connect using your camera software and your camera software supports these The default name is Pat named after the Saturday Night Live character Enter your own info Optical Info You can set up the information about your telescope here The ASCOM functions support these 58 of 236 fields and this information can go inside of photo FITS headers if you connect using your camera software and your camera software supports these In addition the Scripted PointXP capability an Advanced Feature uses this information so be sure you enter the data using the right units that are selected Geographical Information These data fields must be set up fairly accurately for refraction to work properly 4 11 2 Setup Mount Info Tab Setup SiTech AS
267. ort bar in the title bar of the window to minimize the window 4 2 4 Focuser and Rotator Control Buttons Advanced Feature Below the three windows are two control buttons One is Focuser and will bring up the Focuser control window if that option is enabled in the configuration screen More on this later in the Advanced Features section on Focuser The other is Field Rotate similar to the Focuser button this will bring up the field rotator control window if that option is enabled in the configuration window At the very bottom is a button labeled Motors Automatic Normally the controller has the motors in automatic mode However if the voltage is too low or a motor error becomes too great like the motor is stalled etc the motor will go into manual mode The LED for that motor will start blinking on the controller The blinking LED resulted in Drew Aurigema nicknaming manual mode Blinky Mode So if the motors go into Blinky Mode the button will then read Blinky Mode If tracking or slewing the motor will stop To return the motor to automatic mode click on the button when it reads Blinky Mode If it will not stay in Automatic mode look for why the motor is not able to keep up with its commands See the troubleshooting section 38 of 236 4 3 TABBED SECTIONS OF THE SiTechexe WINDOW 4 3 1 Scope Tab Main SitechEXE screen a Viv PointXP 0 Starfs Loaded Controller Mode SLEW
268. ou can put an speed wow sign instead and it will use the previous Ok a bit more about the Anchor command When you click on Add Anchor the current telescope co ordinates are not saved with the command instead at script runtime the current co ordinates of the telescope are remembered This is useful to keep a sequence of PanRel commands from drifting each time the script is sequenced You can create your script by moving your telescope around and clicking the tall row of ADD buttons or you can also edit the script in the text area on the right or you can use a combination of both Be ABSOLUTELY SURE the telescope is in the proper position before adding any commands using position These commands are Slew Pan PanRel Anchor The positions when clicking on the Add Command buttons come from the actual telescope position 5 2 3 Making Scripts Here s a simple session that will move your telescope between M81 and M82 1 Slew the telescope using your planetarium software to M81 It may be a good idea to do an offset init on a nearby star before you record the script 2 Click on Add Slew 3 Click on Add Pause 4 Slew the telescope using your planetarium software to M82 5 Click on Add Slew 6 Click on Add Pause 7 Click on Add Loop The above actions will create the following script Slew 09 56 09 69 02 01 Pause Slew 09 56 27 69 39 01 Pause Loop You could also do it like this Slew M81 Pa
269. ou will have to enter the latitude using the ServoConfig software or upgrade to version 1 6 or later If your scope latitude is known and it is programmed in the Sidereal Technology Dual Servo Controller simply point the scope at the Celestial pole now press and hold the Top Left ESC key for more than 5 seconds when the LED on the Servo Controller flashes fast you may let up 10 5 3 Entering and Leaving the Guide Mode The guide mode can be entered if using SiTech Controller firmware version 1 6 or later by simply pressing the SPD button and toggling through the speed sequences If version 1 6 or later the controller will also automatically enter the guide mode if guiding signals appear on the receiver AutoGuider port If you are using Servo firmware version 1 5 or earlier you will need to use the following methods To enter the Guide mode Hold down the top right key RTN and press the Right button flashlight must be off To Leave the Guide Mode Hold down the Top Right key RTN and press the Right button again flashlight must be off 10 6 EQUATORIAL MODE HANDPAD OPERATION 10 6 1 Tracking Control The top right key will stop and start the tracking flashlight must be off 10 6 2 Entering and Leaving the Guide Mode The guide mode can be entered if using SiTech Controller firmware version 1 6 or later by simply pressing the SPD button and toggling through the speed sequences If version 1 6 or later the controller will
270. ould be added in Alt data but do not overdo this Any number of data points but need at least one set Order of points not important ASCII file with filename SiTech hrz H0 Make Points If you use Nebulosity Save the file ListenSitech neb in your My Documents folder Set up Sitech exe via Config Screen 82 of 236 Note these inputs only address the selected settings to check for scripted PxP Ops Telescope Info Tab Lat Long Scope Focal Length Mount Info Tab Select Mount Type If GEM enable GEM Auto Flip GOTO Miscellaneous Tab Enable Nutate Aberrate and refraction ON Select the camera control software you are using MaxImDL AstroArt Nebulosity or None Enter Camera X Pixels number of pixels wide when UN binned Enter Camera Y Pixels number of pixels tall when UN binned Enter width of each pixel in microns Enter height of each pixel in microns Click on Calculate Field of View button Ascom and Troubleshooting Tab Slew Settling time 10 sec is good starting point to start with If images have streaks increase the settling time Click OK Setup Camera Control S W Make sure MaxIm and or AstroArt are set up to save the RA Dec in the Fits Header Use at least the following versions MaxIm at least 4 11 AA4 at least CCD GUI 4 40 Nebulosity Nebulosity does not save the RA Dec in the fits header so you must run a script from within Nebulosity see below NOTE If Nebulosity is not registered it
271. over long slews from one to the next Problem Is it possible to use only 1 2 the sky Can one do a dozen or so stars over a small area 20 30 deg and get reasonable accuracy over just that area Solution to both above Well I would hesitate to say an enthusiastic YES however a probably may be in order The problem is that it will no doubt model the scope mechanics wrong It won t really have enough info to calculate the fabrication errors and the droop However it may make it more accurate over that portion of the sky anyway Solution It s a good idea to run a calibration over as much sky as possible but on those occasions where you can t do this then just do what you can The calibration will probably not be very accurate in the region where you don t have cal points especially if you have to flip a GEM but its way better than not having any alignment PXP will give you good results in the region where you have some calibration points 185 of 236 Problem I only have a small piece of the sky to work with i e from about 330 around clockwise to 060 azimuth minimum elevation of 45 degrees up in el to about ten degrees past zenith Now my question do I only do a three star cal and forget the rest and accept the errors in pointing or is there something else I should do Will I get good tracking with only three stars for imaging Solution Well in your case the thing to do would be next time you re out under a full sky take a ful
272. ow we hope Dan explained that ok but if you don t understand it then don t worry you don t have to just use it Have a look at the improvement in the following pictures you can see the uncorrected Gurley interpolation error in relation to the corrected Interpolation Periodic Error and also the final improvement from the normal worm periodic error of Chuck s converted to Sitech Losmandy G 11 German Equatorial Scope Dan Software and Firmware Chuck Testing Testing Testing and more Testing Dave Mathematically modeled the concept and gave programming advice 64 of 236 Reference Info Gurley part numbers 320 000 tick R158S05000Q5L16AN18SP04EN 500 000 tick R158SO5000Q5L25AN18SPO04EN R158 spec sheet PDF http www gpi encoders com Info R158 pdf In the following PemPro screenshot taken by Chuck Shaw you can see the uncorrected Gurley interpolation error and the Corrected interpolation error Peak to Peak PE 1 41 Arc secs RMS 0 29 Arc secs Peak to Peak PE 4 03 Arc secs RMS 1 20 Arc secs v gz o on i o E lt In this next PemPro Screenshot taken by Chuck Shaw you can see the un corrected periodic error of his worm gear and the Gurley tick managment with Gurley Interpolated Periodic Error Correction on Peak to Peak PE 1 41 Arc secs RMS 0 29 Arc secs Peak to Peak PE 17 94 Arc secs RMS 6 36 Arc secs Arc Seconds 65 of 236 4 11 4 Setup Miscellaneous Tab
273. p and saved to flash ROM you will have to initialize at the scope zenith and the celestial pole To initialize the Altitude move the scope by hand or with the handpad up to the scope zenith It could be convenient to have a mechanical stop mounted on your scope so it is easy to find this location Press and hold the top right RTN key for more than 4 seconds At this point the controller adjusts your altitude so it reads 90 deg s Important Note there was a bug in the controller flash ROM in versions 1 5 and earlier and this number was calculated wrong If you have firmware version 1 5 or earlier please upgrade to version 1 6 or later or enter the latitude using ServoConfig To initialize the azimuth move the scope to the celestial pole Now press and hold the top left key ESC for more than 4 seconds At this point the controller initializes the azimuth and if you haven t initialized the altitude it initializes the altitude to your saved latitude otherwise it initializes the latitude If you have initialized both the altitude and azimuth you may save the new latitude value by pressing and holding both top keys for more than 10 seconds This saves the latitude to the flash ROM so next time you can simply initialize the scope on the celestial pole and press the left hand key for more than 4 seconds To perform photography or for very fine centering it may be desirable to enter the guide mode This is done by holding down the top
274. pause mode published changes Added Backlash Added Local Search Added Pan and Guide Rate expansion with altitude equal area panning guiding 0S 2g 2g KE K K K K K K K K K K K K K K K K K K K K K K K K K kd Version 2 0 changes DONE millisecond clock add to binary protocol Ascii protocol DONE add int checksum on receive binary DONE Read new Analog Inputs put in binary protocol DONE test Put copies of block 0 1 in high memory This will give us another k 233 of 236 Note this is the last version with the Pic Servo Protocol other than minor updates Make Speed switch do 3 speeds when wired handpad Can t save address 3 to config file using servo config 0 FAS 2g 2g KE K K K K K K K K K K K K K K K K K K K K K K K K K 3 Version 3 0 changes DONE Dumped the pic Servo Protocol DONE make xxj0 command turn off pec control DONE made position reporting return the setpoint if error lt 7 WORKING add SkyCommander protocol WORKING Add PEC control WORKING make binary response return status of pec control Guide mode doesn t like negative numbers fix for gem s looking east Make Speed switch do 3 speeds when wired handpad Changes that need to be made to version 2 1 Fixed the Backlash so a goal of the same number at end of no mans land won t move to the beginning of no mans land 0 FAS 2g 2g 2g K K K K K K K K K K K K K K K K K K K K K K K K K a Version 3 01 1 Made the r a s
275. pe azimuth in a clockwise direction It would be easy to put a negative number into the slew and pan rates to 16 of 236 obtain these results and the controller would respond with the opposite direction but the trigonometry would still be wrong It s also important to note that when the telescope is moving clockwise the azimuth telescope encoder should be increasing and when the telescope is moving up the altitude telescope encoder should be increasing If these move backwards then the direction needs to be changed using the ServoConfig software or change the wiring of the encoders Note If using an old BBAstroDesign handpad the kind with a switch in the middle instead of a push button and Servo firmware version 1 5 or earlier the slew and pan speeds MUST be a negative number but the direction of motion must still be the same as listed above unless using servo version 1 6 You really should upgrade to the latest version V3 5C or later 2 1 2 Operation of Drag and Track Mode If you want the scope to start tracking without initialization point the telescope at the celestial pole and then turn the power on the controller At this point if you ve already set up and saved your latitude the system will be initialized It will immediately start tracking No further initialization is required while pointing at the celestial pole the scope won t appear to track because the celestial pole doesn t move If your latitude isn t set u
276. pen else it will close in 60 seconds b NOTE You do NOT have to keep it open and if you are crowded for screen space it might be best to let it automatically close However the graphic shows the current Alt Az of the scope and the cursor on the graphic shows the current position which is VERY handy for monitoring the progress of script c You also have the option in CalPointsXP 1 09 and later to specify the starting 84 of 236 quadrant and order of the stars This is VERY handy for dome users to not have the dome move back and forth 6 When ready for the Really Big Show click on PLAY a Options Click on the SCOPE tab in the Sitech window to be able to watch the PointXP Stars Stars Loaded counter increment The counter will already show the 2 or 3 initial cal stars you did and will increase from there The script will slew the scope to each of the points calculated by CalPointsXP then after the slew will settle for the time you selected Then the script will take an image using the camera s w and save it in the Sitech folder as Default fit Then the script calls up PlateSolveXP and PSXP solves the image for the RA Dec and sends that back to Sitech Check the Use Sitech Init Window in the script window if you want to watch the init window in Sitech useful to intervene to only do Load Stars Calc Terms if all you are doing is updating the polar alignment measurement Sitech then performs a Cal S
277. per worm revolution is programmed 1 Select the PEC screen from the SiTech ASCOM driver 2 Select whether you have an automatic PEC sensor or not at the left side of the screen 3 Start guiding on a star either manually or with an autoguider 4 Click on the button labeled Arm PEC Record If you have an automatic PEC sensor wait for it to line up and recording will start automatically If you don t wait for the worm to line up with your reference and press the top left button on the handpad When recording is started you will see the status textbox on the left change to Recording 100 of 236 During the next revolution of the worm the controller will record all of your button presses from the handpad or from an autoguider At this time click on the check boxes at the right so the Average 5 collection items and Current Collection item are displayed on the graph Once the worm revolution has completed the status will go to Idle and you re ready for your next record session 5 Click on the button labeled Read Controller PEC Table into Internal Buff 6 After the table is loaded click on the button labeled Load Collection Item from Controller Buffer You ll notice that you will have one more item in the collection 7 Repeat steps 3 through 6 as many times as required We recommend about 6 8 record sessions 8 Now you will have several PEC tables in the Collection You may want to save the collection by clicking on Sa
278. pletes its firt part of the flip Then the RA axis will rotate to the same offset on the other side of the meridian and the Dec will return to its previous orientation with respect to the sky Same thing happens if the scope was initially looking West but all the moves are of course reversed Using this screen button is a very handy way to do flips to confirm cables are routed to not cause snags so you can have confidence in enabling the auto GEM Flip capability but you do need to have initialized the mount first If you see an unexpected snag happening you can stop the motion by simply pushing any of the direction arrows on the handpad 4 5 3 Run Script ADVANCED FEATURE The SiTech ASCOM driver has a powerful scripting feature You can pan the Lunar terminator using relative pan commands Pan the Veil Nebula with absolute pans write your name with starlight etc Making the scripts is as easy as moving your scope or the virtual scope during the day and clicking on various options E Script CurrentCommand Stopped Add Slew tichT extBoxl Stopped Add Pan Add Anchor z Add SlewT o amp nchor Pause Load Script Add PanTo amp nchor Stop Play Save Script Add Pan Relati UnPause Clear Script _Add Pan Relative Add Pause Clear Then Paste M Make a PointXP Platesolve Script gt Add Prompt E n How Many Cal Points posure Binning Make PointXP Run Add Wait 16 4 3 2 4 Add Sound T7 Use Si
279. r Align H Add Stars find AlOffset Add Stars find AzOffset Siaquinyy adoas Do GEM Flip Run Script Controller Stuff PEC Control Offset Track Rates 5yuog audyojog Handpad SlipMode T Colors Close STOP Stopped Bad Scope Commun Ra 05 46 25 3 H Sep HrAng 11 59 59 Dec 00 06 31 Focuser Field Rotate Motors Automatic Start with trying to track medium to high orbit satellites they move slower and select them from the Visual TLE list The best time to do this is shortly after dusk since the satellites are still in the sunlight and you are in the earth s shadow Wait till you see the ISS fly over WOW 151 of 236 14 SKY WRITING AH What you see in the picture above is what we refer to as Sky Writing Its done with a ccd camera set up for imaging on a telescope and the ability to have Sitechexe use a CAD Computer Aided Drawing file in HPGL1 format produced by a freeware CAD program that you use to draw what you want the telescope to trace in the sky Then you simply aim the scope at a star or stars and run the script that you build using the Sky Writing tools in SitechEXE The workflow to do this is 1 Download the required files from the Sitechuser website DOWNLOADS page at https sites google com a sitechservo info home downloads e Save the sound files in the zip file to the Sitech sound folder e Save HPGLToScript to the Sitech folder make a shortc
280. r with motors and a handpad for much less than you would imagine 1 1 BASIC BUILT IN STANDALONE CONTROLLER FEATURES Directly controls two servo motors with the motor position control loops running at nearly 2000 times a second with high speed motor encoders for position feedback on each motor In addition to the two encoders mounted on the motors cleverly referred to as Motor Encoders the SiTech unit can connect to two additional high speed encoders for the telescopes altitude and azimuth or right ascension and declination axes These additional encoders are referred to as Scope Encoders or Mount encoders There is no need to add an additional box to connect mount encoders Mount encoders can correct for slippage of friction drives and 10 of 236 high resolution encoders can eliminate periodic error of worm drives There is an Open Collector RS232 Serial port for connecting 2 or more controllers on the same RS232 bus The other controller axis s can be used for field de rotators and or focusers Available using PC control only You can connect to a wired handpad or an optional radio handpad for slewing panning guiding Signals from the wired or radio handpad work immediately no delay as with some other systems because the same micro controller that is controlling the servo motors listens to the handpad signals No communication protocol delay The Radio handpad protocol is a lean and mean protocol taking
281. ready to resume script click on UnPause button in the script window vee stopped Scope stays pointed at last Cal Point location 8 Close Script Window 9 Open PointXP window in Sitech Scope Tab it s the large button that shows PointXP stars Loaded number a b Click on Display Cal Stars and edit out any stars with large errors Click on Used to change to NOT used to edit out a star Click again to reselect Click on the Help Me button in lower right of PointXP screen for more help Click on Write Config new terms are saved into the sitech cfg file Click on Save Cal Stars pick a filename file extention ends with pxp 5 1 6 PXP Tips and Tricks and Lessons Learned 1 Tracking performance will be a direct function of how good a PXP model of your system you have 2 You MUST build the model using the exact same configuration as you will be using the mount model with If you intend to use a Gurley for tracking than you MUST use the Gurley as part of the model building process to capture whatever errors the gurley itself is introducing Some Lessons Learned are e During the scripted ops you need to make sure you increase the mount Settling Time enough to stop getting smears If you have ANY backlash in your RA system this may be as much as 15 20 seconds e While you do not need a super accurate polar alignment to build your model it will help reduce any image rotation in the future Be
282. refraction calculations you may want to input your temp and atmospheric pressure else just use the defaults if you input make sure the data is in the units that match the checkbox for units SitechEXE can turn all its screens Red for night vision Check the box at the bottom to do that or select a custom color scheme Different schemes are saved in color files that you can select from or save The right side of the tab in the section titled Camera Control Software in Sitech Scripting contains required information to use if you want to use the very powerful Scripted PlateSolve XP routine to automatically use a CCD camera to build a model of your mount errors First you need to select from the software programs listed MaxImDL AstroArt or Nebulosity that you intend to use If you select none that tells the software you will be doing the syncs visually CCDSoft also has the capability to be used but the software for interfacing with CCDSoft is not yet available If anyone wants to use CCDSoft please coordinate with Dan The FOV Field of View section is where you enter the information on how many pixels your camera uses unbinned and the size in microns of the pixels unbinned Note the focal length of the telescope is already available from the information you entered on the telescope tab Then click on Calculate Field of View The windows below will display the camera FOV in arcminutes This information will get used by Pl
283. results both stars should be on the same side of the equator These two stars should have different hour angles on each side of the meridian for instance shouldn t be centered on the meridian Also do not use Polaris for an equatorial scope but its OK to use a star at the zenith The next several stars need to have as much altitude Dec difference as possible Hint If you are starting a new initialization you might consider using this trick When pointed to the first star the scope will not be tracking because it is not initialized unless you have an Equatorial mount running in Equatorial mode but for this lets assume you don t This makes it harder to center the first star because it keeps drifting So to get the mount tracking to make the init easier as the star comes drifting by click on sync anyway remember this is only for the first init When the Init window comes up don t let the timer run out instead just click on Offset Init Leave the Init Window up however It will now be tracking so now you can lesiurely center the star and with the scope tracking and the star centered click on Offset Init again or CalStar Init if your plan is doing Cal Stars Just make sure you only do this if this is the FIRST init 4 9 2 GEM Special Instructions If you have a GEM select one star near the celestial equator and the meridian and the next star near the celestial equator and about 30 deg s in elevation Try to stay on the
284. rev RA Encoder resolution MUST be set to 18000 and the encoders attached to the SiTech controller 27 of 236 6 RA Encoder Res 6 18000 RA Encoder resolution MUST be set to 18000 and the encoders attached to the SiTech controller 7 Dec Encoder Res 7 18000 8 FastTrk ON OFF 8 OFF 12v on Set to ON If the telescope is a DOB on top of an equatorial table the clock needs to be turned off 9 Sidereal Clock 9 ON off RS 232 baud rate must be set to 9600 when attached to the Sitech controller Note that the default SiTech baud rate is 19200 so it also needs to be changed to 9600 10 RS 232 Baud Rate 10 lt 9600 gt Set the SiTech mode to ON 11 SiTech Mode 11 Off ON Press enter to save the last value of ON if it was just changed Turn Sky Commander off 2 5 4 Initial Setup and Testing of Alt Az Sky Commander with SiTech For new installations and for times when one wants to verify that the encoders are functioning properly it is best to do it before proceeding further With the scope pointing at the celestial pole turn the Sitech controller off and then on Turn the Sky Commander on and enter the current date Press enter to Sight Ist Star Polaris Press enter again to Sight 2nd Star Polaris The display should now look something like this 02h 38m 89 3 APN_0001 lt gt CEP Press the up arrow on the Sky Commander to display the count down encoder info The top line of the display s
285. right That s where its worth the effort to have built and installed an autopecsync sensor 10 To make sure you improved things record another worm cycle or two in PemPro with the new PEC file loaded in the controller this time and compare the before and after e Use the refine capability in PemPro to tweak the curve and load the refined file into the controller and repeat that refinement till the verification runs are flat PointXP For more details reference section 5 1 1 1 Do a ClearTerms and Cal Stars 2 Perform an Offset Init on a star to ensure tracking is active 3 Do at least 16 Load Cal Star initializations do more to allow editing out bad inits e OK to use planetarium program s Sync button after slewing to a target and centering it e Once you start LoadCal Stars type of Sync then don t do a Simple Offset Init until you re all done loading cal stars e Once you do a Simple Offset Init then you shouldn t do any more Load Cal Star inits unless you want to start over e PoimtXP calculates many errors but it needs at least 16 Load Cal Star locations to calculate all the terms e For GEMs these stars should be both looking East and looking West e When centering star always make last moves to star using the same buttons on handpad to eliminate effects of backlash e HIGHLY recommend using a crosshair eyepiece or if using a camera a crosshair on screen 4 Stars should be scattered around the sky
286. right key then pressing the right key Now the speed changes by adding or subtracting the guide rate from the current tracking rates To revert back to the normal mode hold down the top right key and press the right key again This feature doesn t work with the old BBAstroDesign handpads with a center switch If you are using servo version 1 6 and you have a radio handpad receiver you will toggle through slew pan guide modes using the SPD button 17 of 236 You may slew the telescope with the handpad or move the telescope by hand and when done slewing or moving the telescope will immediately start tracking again at the new drive rates based on the telescopes altitude azimuth and the latitude To stop tracking press the top right key To start tracking again press it again When the tracking is stopped the LED s will blink off briefly every few seconds version 1 6 of firmware and later 2 1 3 Review of Alt Az Initialization options It may be confusing because there are several ways to initialize the telescope The user has three choices Choice 1 Step 1 Before turning on power to the controller position the telescope to the celestial pole NOT Polaris if in the northern hemisphere but the pole itself Turn on power The controller initializes the azimuth and initializes the altitude to the same value as the last saved latitude Using Choice 1 means you don t even have to use the hand paddle although you must have previously
287. rk itself at that memorized position by clicking on Park Obviously the mount will not move anywhere since it was already at the Park position this time But in the future when you click on Park it will automatically slew to the position it memorized and park itself Then you can power everything down including the controller Be VERY sure the initialization was good on the mount before you do a setpark and park To wake up the mount after it was parked power up the PC and controller and start up SitechEXE and then simply click on UnPark If the mount has not been physically moved since it was parked everything can be powered down while parked and then later powered back up then the initialization data that was valid when parked is still valid The mount will know where it is and is totally ready to do a GOTO and be accurately tracking If you park the scope aimed at a distant object then after it is parked you can move the scope and as long as you accurately re aim the scope at the same distant object before unparking the park unpark routine will work fine Note this assumes the PC internal clock is still reasonably accurate If the bios battery is bad the PC s time may become reset when powered off and the Park information will not be using a correct time for where the sky is located when it unparks This is a really handy capability not just for automatically parking the scope if you stow it in an observatory but but al
288. rlap to work at 12 hours and 24 hours instead of just 24 hours This is the meridian below the pole as well as above the pole Made option to clear all or just the side of the meridian you re on clear all inits gem Focuser can now do manual focus after trying for setpoint It now stops when it gets there This allows manual focus after a move to setpoint 047E Made attempt to fix unpark bug Sent to Mark Simmons 047F Made attempt to fix unpark bug Sent to Mark Simmons 047G Made attempt to fix unpark bug Sent to Mark Simmons I think I got it this time 047H Made the Time always be a certain time in the Getoffsetrates routine Prevents oscillation FAS FAS 2S 2g 2g KE E E K K FAS K K K K K ig K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2k K K 0 46 1 Added servo Error to the Controller Stuff 2 Added on the fly ticks per rev change to controller stuff 3 Fixed spelling on the controller stuff per chuck 4 made default be 2 load init points then offsets then if load inits stays load inits until offsets 5 Added servo error amount to the controller stuff 6 Made refraction changes in config happen without restart 0 46B 7 Fixed bug of some systems not running properly 2 out of about 50 8 Added MoveAxis ascom command can also apply to R A and Dec in 220 of 236 alt Az scope 9 A slew of any kind stops the offset rates 10 A
289. rley brand encoder I did this on my 14 Alt Az scope and my all sky pointing is about 25 arc seconds RMS This is because of Tick Mangament providing accurate information to PointXP By Dave Rowe which has been incorporated in SiTechExe If you have an equatorial and you re on a budget consider getting only one 320 000 tick Gurley encoder Using Tick Managment you can remove all periodic error non periodic error even backlash is taken into account after tracking picks up the slop These encoders cost less than 600 each All of the above Encoder Modes can be applied to each axis or both as required 63 of 236 Gurley Interpolation Error What Chuck Shaw found out was that the Gurley encoder has what we ve named Interpolation Periodic Error IPE There are 5 000 lines on the gurley disk In quadrature this would create 20 000 ticks per rev but Gurley uses a technique called Interpolation A sine and a cosine analog signal are created from photo electronics that are proportional to the angle of the dark line through the glass This signal is converted to digital and then stepped through several voltage levels enabling a higher resolution than if just purely digital In the case of the 320 000 tick encoder the sine and cosine are stepped to create 64 ticks per line and with 5 000 lines this creates 320 000 ticks What we found is that there is a periodic error of about 5 arc seconds for every line or 64 ticks Since t
290. rors Click on Used to change to NOT used to edit out a star Click again to reselect Click on the Help Me button in lower right of PointXP screen for more help Click on Write Config new terms are saved into the sitech cfg file Click on Save Cal Stars pick a filename file extention ends with pxp 204 of 236 Radio HandPad Operation For details reference sections 10 4 4 thru 10 4 11 Turn ON HP SPD Turn OFF ALT SPD or wait 15 Flashlight Top Center on off RTN bright ESC dim Keyboard Lock Hold Alt UP Unlock ALT Down Directions and top 2 simo OK while locked EQ Mode Tracking on Off RTN Top Right Increase rate ESC UP Slower ESC Dn Blinky Mode Top 2 simo or STOP Track in ASCOM Window when plugged directly into Focuser Controller Rt pb OUT Goes to Bigger s Max Left pb IN Goes to Smaller s 0 Full IN when using the Scope handpad to also control the focuser Enable Scope Handpad to control Focuser via Focuser Window Disable Scope Handpad to control focuser in the SCOPE Tab ESC pb OUT Goes to bigger numbers RTN pb IN Goes to smaller numbers To change Xmitter Hold ALT and press lt SPD gt LEDs start flashing Press seq that is lt 254 LEDs stop flashing when stored in Flash ROM Revr Change Unplug from Cntrller for 2 3s plug in and within 10 sec press both ESC top left amp RTN top right simo 4 Revr LEDs flash cute sequence Top Left HP Button
291. rties and that will take you to the Sitech Configuration screens Some programs insist you click on the properties button even if you really do not have anything that needs changing yes sometimes ASCOM is a little weird Next you simply click on Connect using whatever tool is in the Planetarim program you are running After being connecting aim the scope using the handpad to slew for instance to a known star then click on that star in the planetarium and select Sync in the Planetarium and it will bring up the init screen in Sitechexe and will countdown to an Offset Init as the default Read the section of this manual on initializations for how to change to CalStar inits instead of offset inits since that is done from within Sitechexe and not your planetarium program Also most planetarium programs work with their coordinates in J2000 Sitech works in the current epoch i e coordinates have been precessed from J2000 to the current date but expects to receive coordinates in J2000 So Sitech precesses the corridates it receives There is currently no option to tell Sitech NOT to precess the coordinates However ASCOM does provide for the planetarium program to ASK Sitech whether it wants the coordinates cooked or not If asked Sitech will answer that it prefers Cooked coordinates So if your planetarium program precesses the coordinates but does not ask Sitech what it wants you will need to tell it to not do any cooki
292. s 052C Made import of PemPro file 052D Fixed phase of Pempro file import 052E Fixed SyncToAltAz Added check of firmware to 3 3 and if so will reverse the guide rate if looking east Won t set altitude in controller if slewing Made PEC play or record automatically when detecting a zero firmware too 3 3C First attempt at fixing the Portable PointXP problem 052F Fixed Meridian crossing bug Gem If the Bad Gem Init window is clicked Yes then auto init is now cancelled 052G Re enabled the polar align click button Added Rotator Track Paralactic Angle Fixed a couple of procedural errors in the pointxp screen now the number of cal stars is always displayed now when enabling or disabling cal stars the display is updated properly Made the model sensitivity change colors 052H Now ticks per rev comes from config until controller is read Fixed Clear Stars Leave Terms left unused stars in array 216 of 236 0521 Hopefully fixed the use of pointxp bug should be fine now I was sending PointXP the current ra and dec instead of the ra and dec of the initialization KEKEE KE K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 051 Made new installer Fixed the fact that some ascom calls that were not supposed to return right away but returned right away anyway KEKEE KE KE K K K K K K K K K K K K K K K K K K K K K K K K K K K K 050 Added PointXP to SiTech Dumped the Taki routines
293. s easy user interface and simplicity and excellent ASCOM compatibility The ECU Main screen looks like this I The Earth Centered Universe Pro V5 0D ecu cfg Local Horizon Mode File Edit Set Field Orbits Center Animation Telescope Miscelaneous Help wR SAGs Sw Of 4 Bj USA Houston 1X LOT 2009 08 25 03 30pm UTC 2009 09 2 20 30 RA 19 06 38 2 Dec 561003 Azim 039 52 Alt 35 57 Field 31 18 Step 1 min Mag 5 0 14 0 Dayigh Mod To setup ECU to connect to Sitech click on Telescope in the command bar near the top of the screen This menu has a lot of commands that will be referenced Pro V5 0D cfg Local Horizon Mode Animation Miscellaneous Help Enable Telescope Interface v Show Position Use Default Field Target Show Coordinates Track Telescope Auto Track Telescope Telescope Control Confirm Syncs Select Alignment Stars Telescope Type and General Settings ocuser Setup Use ASCOM Focuser Telescope Goto Limits 159 of 236 Then click on Telescope Type and General Settings in the menu that appears Select ASCOM Controlled Telescope SiTech Telescope from the dropdown menu Telescope Type and General Settings Telescope Interface Type j i ASCOM Controlled Telescope SiTech Telescope v Update Delay C 0 05 seconds only if appropriate 0 1 seconds Swap E W Buttons 0 25 d SEUSS M Swap N S Buttons C 0 5 seconds Disable Telescope
294. scope Connection Disconnect COM Port TER ISS Monitor Current Position Azimuth 38 940 Elevation 52 145 Range 11655 109 km Latitude 39 2956 N Longitude 138 9221 E Altitude 344 050 km R A 01 hr 00 m 26 s Dec 21 18m 37s Next Pass AOS No pass in 24hr LOS Max Elev Duration T Alert when visible There are also additional screens to help with situational awareness Two of them that are very useful are FENGYUN 1C DEB NORAD 31207 Sep 13 2009 14 43 00 V Draw Constellations Close 150 of 236 FENGYUN 1C DEB NORAD 31207 Sep 13 2009 14 43 00 Close Sat Tracker has the ability to use a joystick to center the satellite while tracking or to use a mouse mouse is tough at the eyepiece but works great if you are using a webcam and sitting at the computer watching You CANNOT use the handpad to center the satellite while tracking since SatTracker will treat it as a perturbation and simply correct for your inputs and undo what you just did So Dan added the capability to use the handpad but not tell SatTracker about it forgiveness is easier to obtain than permission sometimes eh On the main Sitech screen click on Handpad to Slip Mode Slip mode really screws up normal handpad operations however so only have it checked whiel actually tracking a satellite After the satellite pass remember to uncheck it to move the mount around with the handpad Bvo5sa f Pola
295. scope so it s looking at the zenith but the azimuth is at 180 deg s Stop the tracking 4 Now adjust your declination or altitude pot so the Altitude Dec pot reads exactly 90 deg s 107 of 236 5a Adjust your GEM potentiometer so it reads 270 deg s 5b Adjust your Equatorial scope right ascension pot so the Azimuth RA reads 180 degs 5c Adjust your Alt Az scope Azimuth pot so the Azimuth RA reads 180 degs 6 Now move the declination or altitude axis The potentiometer angle should move the same direction as the declination altitude motor angle If moves the opposite direction you have to select Reverse Supervise Dec Alt in the SiTech Config window 7 Now move the Right Asc azimuth axis The potentiometer angle should move the same direction as the R A Azimuth motor angle If moves the opposite direction you have to select Reverse Supervise RA Az in the SiTech Config window 8 Check that the angles follow the telescope angle properly 9 Set the windows up on the SiTech Config screen so that the angles will never differ more than this amount as you move the telescope It is listed in degrees 10 Turn on Use Supervisory Pot RA Az and Use Supervisory Pot Dec Alt 6 AUTOGUIDING To set the Guide mode speed you must use ServoConfig exe using the Edit Parameters button Details on doing this are in the Setup Manual Remember you cannot have Sitechexe connected to the controller at the same time servoconfig is connec
296. shape that s been plotted to HPGL 1 IN PS4 RO0 IP IW SP1 PA SP1 PU 5080 4572 PD 6096 5588 PD 6096 4572 PD 5080 5588 PD 5080 4572 PD 5080 4572 PU SP0 Here s a screenshot of the conversion screen based on the above plot file E Make a SiTech Script File from an HPGL file TOX HPGL File to convert to SiTech Script file C Visual_CSharp_NET_Samples HPGLT oScript Circle hpg Rt Asc SizeDD MM SS Dec Size DD MM SS Speed Deg s per second 02 56 22 01 56 11 0 07 Starting R A Starting Declination F X Declination 12 39 56 29 12 27 Get Ra Dec from SiTech a inversion Output Script File Script Copy Script Exit Sound C Program Files Common Files ASCOM Telescope SiT ech Sounds CoverScope wav Wait Slew 12 39 56 29 12 27 Sound C Program Files Common Files ASCOM Telescope SiT ech Sounds Filter wav Pan 12 44 22 28 14 21 0 07 Sound C Program Files Common Files ASCOM Telescope SiT ech Sounds UncoverScope wav Wait 0 5 Pan 12 35 29 30 10 32 Pan 12 35 29 28 14 21 Pan 12 44 22 30 10 32 Pan 12 44 22 28 14 21 Pan 12 44 22 28 14 21 Sound C Program Files Common Files ASCOM Telescope SiT ech Sounds CoverScope wav Wait 0 5 Sound C Program Files Common Files ASCOM Telescope SiT ech Sounds Complete wav Blue using a DSLR or singleshot color When I made up the PAN routine I had two choices there is a 3rd better choice but it would 153 of 236 require controller code I could make th
297. side The curve should be the same as the averaged buffer curve That s it From now on if you have an autopecsync detector just make sure use autopecsync is checked on the PEC graphic page and it s all taken care of Otherwise after starting up the controller you should simply do a single manual PEC sync To make sure you improved things record another worm cycle or two in PemPro with the new PEC file loaded in the controller this time and compare the before and after You can use the refine capability in PemPro to tweak the curve and load the refined file into the controller and repeat that refinement till the verification runs are flat The biggest issues with this are usually not getting the Pec Sync done correctly so pay particular attention to getting that right That s where its worth the effort to have built and installed an 102 of 236 autopecsync sensor Tips for using PemPro with Sitechexe e Verify tweak your mount s polar alignment before using PemPro to capture your mount s performance e Always run the Calibration Wizard in PemPro to make sure the pixel size and camera rotation are accurate e Always make sure you have done a worm sync either manually or autosync detector and have use autoPecsync selected on the PECGraph if you are using an auto pec sync detector e Its worth your time to understand and build a PE fundamental frequency table for your mount so you understand whether
298. site and also discussed in this OPERATIONS Manual However the MegaStar To ASCOM program was written specifically for MegaStar and the timing compatibility it needs If you are a MegaStar user try both programs and see which works the best for you The rest of this section in the Manual will assume MegaStar To ASCOM is being used 171 of 236 There are also a number of different virtual serial port emulators available The one described in these instructions is com0com ComO0com is a null modem emulator that is an open source virtual serial port driver for Windows and is available freely under GPL license at http com0com sourceforge net Since there are details instructions for install setup and use in the MegaStar To ASCOM manual that is included in the MegaStar To ASCOM zip file available for downlink from the Sitech user s website they will not be repeated here The user interface is shown below MegaStar To ASCOM loj xj face nnect Clear Log no handshake Coordinate Settings The setup instructions in the manual discuss using the option for MegaStar To ASCOM to convert RA and Dec from J200 to apparent Since Sitech already does this do not use this option in MegaStar To ASCOM Also Sitech uses either SlewTo or SlewToAsync commands so since MegaStar To ASCOM checks and uses the SlewToAsync is available that should also take care of itself for you There are really good operations instructions in the MegaStar
299. small button on the right to memorize the position or change the numbers in the Up Down adjustment boxes These labels and positions you set up are only temporary To save them you must click on the Save Presets button There is an Out limit and an In limit Set these up as necessary and the click Save Presets The Reversal amount is a really great feature If non zero the focuser will move past the desired location then return to the proper location This only happens in one direction This allows taking up the entire backlash If you want backlash to be taken up in the opposite direction then make this be a negative number Don t forget to Save the Presets after changing this number 125 of 236 9 SiTech ASCOM DRIVER IMAGE PLANE ROTATOR To use the SiTech Rotator software routine you need to have a second SiTech Servo Controller to control a servo motor to rotate your image plane rotation system The rotator will use the Alt Dec channel on the second controller The primary focuser will always use the Az RA channel If you use two focusers the primary focuser uses its Az RA channel and the secondary focuser will use the Alt Dec channel So you would need to choose between two focusers or a primary focuser and a rotator for your configuration You need a Y RS232 communication cable so the SiTech Ascom Driver can communicate with both controllers at once The Rotator is plugged into the Alt Declination channel The cable pinou
300. so for portable systems if you want to observe something during daylight the next day assuming the mount is in the same position as it was when parked simply power up start SitechEXE and UnPark Venus and other planets can show up well during the day time 40 of 236 IMPORTANT NOTE If you end up moving the mount after you have Parked the mount then when you do an un park the mount will think it is in the original position it was parked it That means the handy initialization that would have worked great will be trashed and you may get some really bizarre behavior till you get it re initialized Be VERY sure you are in the S xis Er 00 00 00 1 Pasis Err 00 00 00 0 SAxis 105 57 33 saines 4 ScopeAz 17 53 13 ScopeAl 27 15 51 Refract 00 00 00 commdif 250 LST 08 34 40 5yuog wuAco joy H STOP Tracking Reading Servo Parms Ra 1 4 50 41 3 H Sep Hr amp ng 1 7 43 59 Dec 74 06 59 Focuser Field Rotate Motors Automatic This tab is not normally used for routine operations and so as such could be considered an Advanced Feature but since it is really only for looking at for additional information that can help with troubleshooting and for situational awareness for things like whether an axis is binding or perhaps overloaded like if the axis is not well balanced etc we will address it as part of the Basic Features 41 of 236 The H is
301. st the scope Local search Upon a quick combination keypad request your telescope will search for an object in a circular pattern This is the most efficient search pattern as there is no overlap between successive search patterns This is a true circle no matter where in the sky you are looking No inefficient ellipses at different altitudes You have two choices of radius reverse forward and pause control and speed of the search can be changed while looking through the eyepiece Internal Backlash Backlash is internal to the controller and instantaneously applied Each axis has a backlash variable associated with it and an adjustable backlash area speed Equal Area Pan Guide Speeds The Azimuth RA Pan and Guide speed is automatically adjusted for different Altitude Declinations As you near the Zenith or Pole the Pan and Guide speeds are automatically increased so the same sky area is covered in Azimuth RA as Altitude Dec This is a really cool feature and if you experience it you won t want to go back 11 of 236 The controller has many advantages over competing systems e Small size 2 5 by 4 25 by 1 e Power Efficient Will last several nights on one 7 amp hour Gel Cell on most telescopes e Built in flash memory for saving parameters e Firmware in the controller is field upgradeable to later versions of the firmware no need to send it back to the factory for additional features 1 2 ADDITIONAL FEATURES AVAILABLE US
302. still works fine in demo mode for PxP Ops Nebulosity works really well and you should strongly consider registering it IMPORTANT Make sure all cables etc are clear to allow scope to slew to any Azimuth Alt without snagging etc GEM will perform at least one and possibly more Meridian Flips If cables are not clear be prepared to tend the cables to allow the script to proceed without interruption If an unanticipated snag etc is about to happen OK to click on PAUSE for the script and then RESUME when cleared 5 1 5 Scripted PxP Operations Procedure 1 Initialize telescope OK to have a planetarium program connected to Sitechexe to do the initializations a Click on Clear all terms and Cal stars in the PointXP window b Perform an Offset Init to start tracking c Manually perform at least one Cal Star Init 2 or 3 separated in alt Dec and az RA are better to provide pointing accuracy to better than your cameras FOV 2 of them should be separated in RA Az as much as possible and the 3rd separated 83 of 236 as much as possible in Dec Alt Important to not perform any Offset Inits after these first 2 3 CalStar Inits before performing the Scripted PxP Run 2 Call up camera control s w and connect to camera if not previously done a Verify good focus Make sure Focus mode is exited and not running when script is started b For Nebulosity run the ListenSitech neb script i Click on Edit Run Script
303. sure in a dark room hardcore dark sky enthusiasts Approval was given by both Chuck Dethloff and Howard Banich experienced dark sky observers from the Portland Oregon area In addition to this the glow lasts all night long making it easy to find on the observing table in the darkest night Although the labeling on the buttons may not be discernible the shape and thus the location of specific 130 of 236 keys are easily discerned 9 Keypad Reliable custom manufactured Silicone One Piece Push Button pad which presses against gold plated contacts 10 Industry standard autoguider port is built in to the receiver This port can be used to autoguide a telescope with or without the ASCOM driver or Mel Bartels scope control software It will even work with the Argo Navis or stand alone tracking 11 Auto Off for both the flashlight 14 minutes and the transmitter 30 minutes 12 Long Battery Life Years if a button is not inadvertently left pressed It uses an easily replaceable standard 9 volt alkaline battery 13 Wide keypad spacing for gloved operation 14 Transmitter can be used with a direct connection to the telescope controller in case of interference or if the battery runs down SiTech Controller Only 15 Digital I O added 4 inputs or 2 inputs and 2 outputs are available for software to use 16 Handy necklace is included 10 2 TECHNICAL INFORMATION The transmitter and receiver utilize a pair of Lynx Technolog
304. system Mel s system is the only stepper system we know of that is less than the SiTech servo system and then if you want to do imaging planetarium software control while still tracking or other simultaneous computer operations you ll still have to use a 2 computer Some books or articles may mention Servo Lag as an advantage of a stepper system over a servo system This isn t an advantage when compared with the SiTech Servo system When tracking the servo motors will almost all the time be within ONE motor encoder tick and occasionally two motor encoder ticks of its desired position This is usually between 1 10 to 1 4 of an arc second depending on your gear ratio Despite the many advantages of a servo system over a stepper system many successful stepper systems have been created which work extremely well 1 4 SAFETY The servo motors are powerful motors that can do extreme damage to equipment and or plant and animal life Please be careful that your telescope doesn t move to a mechanical limit such as the ground You may damage the motors or gears and you may injure yourself or others Use this product at your own risk 1 5 SOFTWARE VERSIONS The manuals are written and illustrated with screen shots using current versions of SiTech control software SiTech EXE v054M and Firmware Version 35C Please update to these or later versions in order to use all the features available You can find the latest versions at http www si
305. t Appendix F Troubleshooting Initialization Troubleshooting GOTO and Tracking Troubleshooting PointXP Troubleshooting Controller Stuff Menu Item Motors and Encoders Reading Controller Parameters Motor Operation Troubleshooting Handpad Operation Troubleshooting Radio Handpad Troubleshooting DragNTrack Mode Troubleshooting Equatorial Mode Troubleshooting Argo Navis Mode Troubleshooting Sky Commander Troubleshooting Interface Troubleshooting with other Programs Guide Mode Appendix G RF Handpad Receiver Pinouts Appendix H Cue Cards Normal Startup Initializations Drift Align GOTO SetPark Park and Unpark Periodic Error Correction PemPro PEC Training PointXP Scripted PointXP Operations Radio HandPad Operation Appendix I PlateSolveXP Appendix J CalPointsXP Appendix K Version History SiTechExe Version History Controller Firmware Version History 6 of 236 159 165 169 171 174 175 178 182 182 182 185 187 187 187 187 188 189 189 191 191 192 192 192 194 195 195 195 196 196 197 197 200 201 202 205 206 209 211 211 230 Revision History for the OPERATIONS Manual Version 1 1 October 20 2009 Baseline edition 7 of 236 THE BIG PICTURE READ THIS FIRST There are two parts to the documentation for the Sidereal Technology Servo Control System s documentation The first part is the SETUP manual and the second part is this OPERATIONS manual Skim through them both to
306. t by checking the Use Focuser Rotator checkbox You will not be able to Set the scope to encoders or encoders to scope if you re viewing the Focuser Rotator controller 96 of 236 Reading Controller Parameters You basically have to stop the normal communication loop and ask the controller for a specific parameter As this would conflict with normal telescope communication we ve made it possible to only view one of the parameters at a time Simply hover the mouse over the desired parameter and it will read continuously This feature can be very helpful to see what controller volts you have finding mechanical problems in your telescope can be easier by watching the current and other helpful information Terminal Mode The bottom text areas are a terminal The one on the left is what you type After Pressing the Enter key the data you ve typed is sent to the controller The data that is received is displayed on the right hand text area If there is no response from the controller there will be an Underscore This will be after a short time delay The SiTech Telescope Driver automatically ToUppers your commands so even though the controller needs upper case you don t have to use uppercase It is possible to make your scope run away or do other bad things so be very careful when using the terminal mode If you don t understand what you re doing or have a direct instruction from Sidereal Technology it s best just to not do anythi
307. tar Load Init and the PointXP Stars Loaded counter on the Sitech Scope Tab increments If a solution is not quickly found PlatesolveXP will search 999 default value FOVs around tgt Alt Az the script will move on to the next star and then the whole process repeats till it has slewed to each of the init points in the script e Click on Show Image in PlateSolveXP to see the image with the catalog stars and targets marked This is especially useful if PlateSolveXP doesn t solve It could be smeared star images if the controller hasn t finished it slew e Click on STOP in the PlateSolveXP window to stop looking before the 999 FOVs and move on to the next point e If you click on Keep Window Open in PlateSolve script will stop till window is closed then it will resume else the window will close in 7 seconds e The active script step is highlighted in the scrolling script window If active step scrolls out of sight simply click in scrolling window to have it re appear e If you notice the focus has gotten bad mirror shift etc click on the PAUSE 85 of 236 7 When script completes script status window will indicate button in the script window NOT during a slew Then you may control the camera from the camera s w and refocus then remember to exit focus mode o If you are using Nebulosity you will have to abort the script abort button in Nebulosity Restart the script when done o When re focused and
308. tation activity in Appendix D of this OPERATIONS Manual 5 2 11 Periodic Error Correction with PemPro If you are using SiTech exe 53D or later and with v34c bin or later in the controller and are using at least PemPro v64 its super easy to use First clear out any PEC curve in the sitech controller by using the PECGraph display in sitechexe and clicking on Clear PEC Table in Controller in the left column of buttons Verify the PEC Curve in the Controller is a flat line by clicking on the Read Cntrler PEC Table 101 of 236 into Cntrler Buffer button in the left column Make sure Show Latest from Controller is checked on the far right and verify the green line that is displayed is flat If you have an autopecsync detector go to the pec page in sitech exe and turn it on If you need to do a manual pec sync instead then do that just need a mark on the worm and an index point to line the mark up with There s no need to even stop tracking Now in PemPro be sure you are connected to the camera and also the mount In the setup for PemPro make sure you get the worm period set up correctly and I suggest always running the PemPro calibration wizard to verify the camera pixel resolution and rotation angle Then simply click on sync PemPro will query SiTech exe for the phase of the worm and you will see the PemPro display update accordingly Then record several worm periods in PemPro by clicking the START button in P
309. teSolveXP performs a fast square spiral search around the initial guess until it finds a match or until the number of searched regions exceeds a user specified limit It returns the coordinates of the field center the image scale and the rotation angle of the image It graphically shows the extracted stars the catalog stars and the matched stars It also displays the J2000 coordinates of the cursor a useful feature for astronomical research and object 78 of 236 identification The screen grab below shows the main screen of PlatesolveXP on the left and the image window of PlatesolveXP that appears when you click on Show Image Note the stars that have been identified are marked on the image by Platesolve the bright spot in the center is the core of M 74 Click on the ICONs at the top of the image screen to identify the meaning of each of the markings The bullseye ICON will bring up a photometry screen and will show estimated magnitudes of targets in the image PlateSolveXP 1 13 m 4 fit gt PlateSolveXP 1 13 IMPACT INFC on aoe Oe m Image File Name Chuck Shaw My Documents CCD IMAGES 091 007 m74 fit RA O1h36m44 4s RA 01h36M39 1s g r Dec 15 47 13 Dec 15 47 00 Plate Size 51 x 38 Max Regions 999 Plate Geometry Tocame PielSize 4 4481 lt lt J Angle 357 82 Plate Match Found Stretch 1 Skew 0 001 Plate Size 51 6 X 38 55 r Starting Values lee Image Center Extracted 30 Found
310. techservo info downloads 14 of 236 2 OPERATION WITHOUT A PC The Sitech system is capable of running without any external control system connected to the controller aka in computer less mode There are four different modes available to do this 1 Drag and Track which assumes you DO have mount encoders on the mount which can be an Alt Az or an Equatorial mount With mount encoders you have the option to simply loosen the clutches on the mount and grab the telescope and drag it to another location and retighten the clutches The mount encoders will update the controller s knowledge of its position and tracking will resume at the proper rate for the new location obviously for an equatorial mount the rate stays the same Slew and Track which assumes you do NOT have mount encoders on the mount which can be an Alt Az or an Equatorial mount For this mode the system relies on the motor encoders for slews to know where the mount is aimed So you need to use the handpad to slew to a new location to have the tracking rates be correct again for equatorial mounts the rates will obviously not change Equatorial Mode which assumes you have an Equatorial mount or a tracking platform that is reasonably polar aligned and works with or without encoders since basically all it does is turn the RA axis at a sidereal rate Operation with an Argo Navis Digital Telescope Computer It is possible to use the Sidereal Technol
311. ted In general the best autoguiding speed for the RA axis is less than the sidereal rate of 15 arcseconds second That way guiding commands to the east will slow but not reverse the RA motor and avoid dealing with any RA backlash There are three ways to autoguide the Sitech system e If you have an RF Handpad simply plug in your SBIG type autoguider cable into the RF Handpad Receiver autoguider input port You can also plug in a relay box to that same port that provides the same type of SBIG type output As soon as an autoguider input is detected on the autoguider input port the Controller will automatically go into Guide Mode e If you do not have an RF handpad you can use a custom relay box that takes whatever autoguiding commands your autoguider outputs and then converts them to standard Sitech Handpad inputs You can either build a Y cable that allows plugging in both this custom relay box and the handpad at the same time or simply unplug the handpad and plug in the custom relay box in its place Use the circuit diagrams in the SETUP Manual to ensure your custom relay box outputs are the same as the standard handpad s outputs Using this approach you will need to manually put the controller into guide mode use the virtual handpad on the Sitechexe window to click on guide mode e Whether you have an RF handpad or not you can also use ASCOM Pulse guide Guiding 108 of 236 assuming your autoguider software is ASCOM compatible
312. that SitechExe uses are all ascii files that are easily built and or edited and the filename extention must be dat The format is the same as is used by Mel Bartel s Scope exe program and the coordinates must be in J2000 and separated by a space H M S D MS The first 6 lines of the file Messier dat are provided below as an example 05 34 31 9 22 00 52 M1 Gal Nb Tau Crab nebula Taurus A 21 33 27 2 00 49 22 M2 GlobCl Agr 13 42 11 2 28 22 34 M3 GlobCl CVn 16 23 35 5 26 31 29 M4 GlobCl Sco 15 18 33 8 02 05 00 M5 GlobCl Ser 17 40 17 0 32 16 00 M6 OpenCl Sco Butterly cluster The files are all saved in a folder named Database at C Program Files Common Files ASCOM Telescope Sitech Database The data from NamedStars dat came from Bill Gray s Guide 8 I have converted it to a different format however the data came from Bill Grays file named COMMON2 NAM Used by verbal permission 5 11 2007 The data from Messier dat came from Bill Gray s Guide 8 I have converted it to a different format however the data came from Bill Grays file named messier nam Used by verbal permission 5 11 2007 Thanks Bill The Flamsteed and Bright Star Catalogs all 5thMagStars and 3rdMagStars came from Don Ware Thanks Don The data for the NGC and IC projects came from http www ngcic org This website has been changed to http www ngcicproject org default htm Here is the quote from their website The Historically Corrected New Gener
313. the correct encoder tick values setup in the SiTech controller as well as a reasonably accurate mount 2 5 5 Starting and Using SiTech with Sky Commander for Alt Az Ops Starting with both units off first turn on the SiTech controller and slew to the North Star celestial pole Turn SiTech controller off and then back on This is where the scope assumes that it is starting pointing at the celestial pole This is done so that subsequent tracking while setting up the Sky Commander is reasonable Next turn on the Sky Commander Enter the correct date Perform the 2 star init with Sky Commander See Sky Commander user manual for init procedures It is not recommended using Polaris for the sight stars in Sky Commander Select 2 start at least 20 degrees from the celestial pole The 2 stars should be in the general area where the scope will be used and at least 30 degrees apart A good example is Arcturus and Altair Once the 2 star init is completed the Sky Commander can be synced with the SiTech controller WARNING Note that when syncing press the 2 top buttons of the SiTech hand pad not only does the sync occur but SiTech will slew GOTO the currently selected object in Sky Commander by default it is APN_0001 in Cepheus If you re not ready for this it is quite frightening since you have no idea what your scope is doing where it is going and whether it will ever stop So before syncing I recommend making s
314. the settling clock is running another good reason to have a reasonably long settling time used Then you can focus and when done simply click on unpause to resume e Ifyou have any difficulty getting PlateSolve to obtain a solution the first thing to check is if the FOV for you camera is reported correctly to PlateSolve If this setting is too small you may never or rarely get a solution Then look at the image to see if the stars are points or if stars are there at all PlateSolve will handle a fair amount of smear but there is a limit 5 1 7 Aligning PointXP Using other Plate Solvers Using a digital camera with a plate solver software such as ELBRUS free at http astrosurf com pulgar or PinPoint LE available as part of MaximDL Both these 87 of 236 programs connect to SiTech exe with ASCOM and allow very accurate determination of pointing errors for PointXP to calculate corrections Here is how Juan Herrero used Elbrus used Sitech CCDsoft Elbrus and an ASCOM compliant sky atlas Press Clear terms and Cal Stars in PXP Set Elbrus to automatically solve after every new image captured First do a regular star init The scope must be inited within 2 degrees accuracy for Elbrus to start solving in automatic mode Once the telescope is roughly inited take an image 10 to 20 seconds in my case Elbrus will automatically solve the image Press the synchronize telescope button in Elbrus This will bring up Sitech
315. then connect to and send receive its LX 200 commands with The LXtoSitech acts as a translator to take the incoming LX 200 commands and data and change them to ASCOM Commands and data and vice versa The two screens that come up are shown below You normally do not have to do anything with either of these screens and they are happy as a clam to be buried behind other windows NOTE When you are shutting things down start with disconnecting the non ASCOM program from the virtual serial port first Then close LXtoSitech by clicking on QUIT and then close HW_VSP Otherwise HW_ VSP will get upset EE LxToSitech vo 72 E X GZ Response 00 00 00 Q Response Sr 08 44 07 Response 1 Sd 67 12 42 Response 1 MS Response 0 D Response RE0 049 Response RA0 195 Response Mw Response Mn Response Mw Response 127004 Mn Response REO 035 Response HW Virtual Serial Port 2 5 10 Virtual Serial Port UDP Search Binary 1 0 Settings License IP Address Port S Port Status a05 Status Opened Server Pot Baud 9600 Port Name RA0 139 Response Mw Response Mn Response GD Response 00 00 00 GA Response 00 00 00 Scope Connected HW_YSP Connected NVT 2217 Yes M Ethernet Status Client Connection Server Connection Connected RxBytes 32 TxBytes 121 s05 Device Mode Client Bits Parity Stop Bits Handflow None Rx Bytes 121 Tx Bytes 32 X
316. this installed already please download and install from here lt http www microsoft com downloads details aspx FamilyID 262d25e3 f589 4842 8157 034d1e7cf3a3 amp displaylang en gt There are later versions of the Microsoft Dot Net Framework than 1 1 but they install in addition to 1 1 and do not replace 1 1 So you MUST install version 1 1 If you run a program like PemPro it will require Microsoft Dot Net framework version 2 0 In that case install version 2 0 in addition to version 1 1 required by SitechEXE 31 of 236 NOTE If you are using a computer set up to use European regional settings in Windows it will use those regional settings for the use of points and commas when trying to convert strings like in the cfg file to floating point and Integers European settings use a point where American settings use a comma and vice versa Be sure you use American settings if you are getting bizarre behavior when trying to install and initially run SitechExe The second software package is the ASCOM Initiative Platform While not technically required to install and run SitechEXE if you want to take advantage of many of the capabilities of SitechEXE to interface with other programs you need to have at least version 4 1 installed You may download it from http download ascom standards org ascom41 exe Unlike the Dot Net framework later versions of the ASCOM platform do include all previous version capabili
317. ties so it is recommended to check the ASCOM Initiative website to download and install the latest version available You can access it at http ascom standards org You do not need the developer kit download nor do you need any of the other drivers or plugins unless you have a unique capability or software that is specifically listed If you are using TheSky it requires that you make a small modification to the ASCOM installation after installing it Information on this simple modification is in Appendix B of this OPERATIONS Manual ASCOM is an acronym for Astronomy Common Object Model It is free software that was developed by a dedicated group to provide a way for many different planetarium programs or other software to control many different types of telescopes This makes it easy for a telescope control system company to write only one driver and suddenly all planetarium programs can control their scope ASCOM as well as the Sitech ASCOM driver are both free software Once these two applications are installed then you are ready to install the SiTech Telescope Driver SiTechEXE The first time setup of SiTechEXE requires that you to use a SiTech Initial Install version SiTechEXE051 zip is currently as of the date of this manual the install program used by most current users Download it from http siderealtechnology com SiTechExe051 zip Download it to a directory all by itself unzip it then run the Setup exe program
318. tion and then click on the drop down combo box labeled Init Focuser To to select the position to Init to The top text window is the current focuser position The number is based on your Ticks Per Engineering units specified using ServoConfig This could be in inches or in millimeters If a red button to the right of this is shown there is no communication between the computer and the 2nd controller The next layer of buttons is the Fast buttons In or Out The next layer of buttons is the Slow buttons In or Out The next layer of buttons allows you to use the telescope handpad as a focuser adjustment If you click on the Slow button pressing the top left and the top right buttons on the telescope handpad ESC and RTN will focus in and out at slow speed If you click on the fast button pressing the top left and the top right buttons will focus in and out fast There is a communication delay for this and the start and the stop of the focuser will be delayed somewhat It would be better to use a separate handpad for the focuser The next layer of buttons is Jog In or Out a specified amount Set up the Jog Distance then when you click on the Jog In and Jog Out the focuser will move exactly that far Next there are 5 Eyepiece Camera focus setpoints To change the name right click on the label button To set up the location for a particular point move the focuser until it is in the proper position i e focused and then click on the
319. titude of the local horizon in degrees The altitude of the local horizon is measured upward from 0 degrees and the azimuth is measured from the North horizon East is 90 degrees South is 180 degrees and West is 270 degrees regardless of hemisphere The horizon file can be a single entry If so the horizon is assumed to be constant at the altitude given by this single entry Entries can be in any order in azimuth The horizon is linearly interpolated in altitude between successive points in azimuth and it is rapped and interpolated through O degrees The program limits the local horizon altitude to the range of 2 5 degrees to 85 degrees Running CalPointsXP from the Command Line Call CalPointsXP from the command line as follows Path CalPointsXP exe NumPoints Installation Latitude Filename NumPoints The desired number of calibration points Installation A string of the form Mount Order where Mount is GEM AltAz or Eq and Order is NE NW SE SW or null The Order string defines the starting direction of the calibration point ordering If it is left blank then nearest neighbor ordering is used For example if the Installation string equals GEM SW then the mount is assumed to be a German Equatorial and the ordering begins in the SW nearest to the meridian and proceeds through North to the calibration point nearest to the meridian in the SE The Installation string is not case sensitive Lati
320. ts are in the SETUP Manual appendices Once you use ServoConfig and change the address of the second controller to 3 set up the Slew and Pan speeds and the Ticks Per revolution then you re ready to go Next in the SiTech configuration menu click on Use SiTech Rotator Note When communicating to the either controller using ServoConfig you MUST unplug the communication link to the other controller You cannot have both SitechEXE and ServoConfig both using the RS232 cable at the same time If you find that the stars are rotating a lot in your images you may have this working the wrong way Use ServoConfig remember to use address 3 and unplug the first controller and reverse both the Altitude Declination Motor direction and Motor Encoder Direction Now the SiTech driver will communicate with both Servo controllers at once using only the one serial port cable with the Y connector From the main SiTech window you can call up the Rotator window by clicking on the Field Rotate button 126 of 236 9 1 DESCRIPTION OF THE ROTATOR WINDOW The following window is the latest version of the Sitech Rotator window FieldRotate Field De Rotator Rotator Angle 00 00 00 Parallacte Ang 01 19 06 _ Parallactic Rate 0 96972 Rotate FAST ea Rotate SLOW Et Enable Slow Handpad _Fast cow Jump Field Cw Field Jmp Size ko Move To ng 0 00 Rotate to Stop Par Angle Init Rotator to Zero
321. tude The user s latitude in degrees negative in the Southern hemisphere Filename The full path and filename of the horizon file Output File CalPointsXP creates an ASCII text file with the same name and path as the input horizon file The extension of the new file is cpz This file contains the azimuth and altitude of the calibration points Azimuth1 Altitude1 Azimuth2 Altitude2 Etc 209 of 236 where Azimuth and Altitude are in radians The Azimuth values start at 0 in the North and increase toward the East CalPointsXP Usage CalPointsXP can be run as a normal Window s exec A horizon file must be created before the program can create calibration points Input the desired number of points then select the mount type and enter the Latitude if the mount is an equatorial Select the desired calibration point ordering and press the button labeled Make Points You will be asked to select a horizon file After calculating and displaying the calibration points the program will save the list of pointing directions to a file with the same path and name as the horizon file having extension cpz The pointing direction of the telescope s primary axis is displayed as a red circle and the local horizon is displayed in green Calibration points and their order numbers are displayed in cyan If the SiTech ASCOM process is present and running CalPointsXP will display the pointing direction of the telescope as a yellow circle with a cross T
322. uatorial Otherwise use Offset Inits However it s really easy to mess things up if done wrong So before you start initializing your telescope using Cal Star Inits do all the offset inits you want but once you start adding Cal Star init points do NOT I repeat do NOT perform any more offset inits until you have added all the stars you want Once you ve added all the stars into the matrix then it s ok to start performing offset inits but once you do ONE offset init then you do NOT want to do any more add init point inits during that SitechEXE session The SiTech ASCOM driver knows this and the default will be offset inits until you perform 55 of 236 one Cal Star init point then the defaults will be Cal Star Inits until you do one offset init then the default will remain Offset inits till you do another CalStar Init 4 9 6 Initializinging the Scope on a Fixed Object If you want to build a visual basic script to initialize your scope using a daytime fixed object i e you did not use Park the night before then do the following Using an ascii editor like notepad type the following exactly as written Set Scope CreateObject SiTech Telescope Scope Connected True Scope SyncToAltAz 270 0 45 0 Scope Connected false Save the file as a text file txt with any name you want and then rename the file so the extention is not txt but is vbs This can be put in any folder it does
323. unt operation It can set the controller to automatically start tracking on startup for future operation without a PC connected The second file is the latest version of V BIN file that loads the firmware into the controller It is periodically updated to take advantage of updated capabilities The third program is SiTechEXE exe and it is the main control program for operation of the controller when you use a PC Most of the more powerful capabilities realized with the Sitech system are accessed and used via SitechEXE exe The versions of these three files as of this manual are ServoConfig exe version 1 1 SiTechEXE054M zip V35C BIN Go to the Download website at http www sitechservo info downloads for releases that have come out since this manual was updated 3 2 LOADING THE SOFTWARE ServoConfig exe is a stand alone program for configuring the controller with motor ticks per revolution and motor speed control parameters Use this program to set the tracking pan and slew rates for each axis You must use ServoConfig to load the BIN firmware file into the controller Use the SETUP Manual for details on installing and using ServoConfig exe and updating the firmware and the basic mount configuration settings Installation of two other external software packages is required before you install SitechEXE The first is the Microsoft Dot Net 1 1 framework You MUST have the free Microsoft Dot Net 1 1 installed If you don t have
324. up and running An ICON is supposed to be automatically placed on your desktop when you install it so just double click this ICON However this is not absolutely necessary the driver will start up automatically when requested by a planetarium program but it takes a lot longer to connect when doing it that way 3 4 CONFIGURING THE SiTech TELESCOPE DRIVER Just as you had to setup the Controller with critical information about your mount you also need to set up various parameters in the configuration settings in SitechEXE so it will operate correctly Much but not all of the critical basic information about the mount and the controller settings are obtained directly from the controller by SitechEXE However there is a configuration page that you will need to access to update other required information If you have not done so already be sure to use the SETUP Manual to update and then save the following information in the SiTech Dual Servo Controller Flash ROM using the free ServoConfig exe program before running the SiTechEXE Telescope Driver The parameters that MUST be set up are Primary R A or Azimuth MOTOR Ticks per telescope revolution 360 Secondary Dec or Altitude MOTOR Ticks per telescope revolution 360 Primary R A or Azimuth Telescope Encoder Ticks per telescope revolution if used Secondary Dec or Altitude Telescope Encoder Ticks per telescope revolution if used Slew Speed Primary and Secondary axes
325. ur best bet would be to use the DragNTrack mode but slew with the handpad instead of dragging the scope If you don t have external encoders and you plan to use the SlewNTrack mode you must set your controller up for SlewNTrack so the controller will ignore the telescope encoders if using the Argo Navis If tracking before connecting a computer or Argo Navis is not desired there is no need to initialize the controller on the celestial pole 20 of 236 2 3 EQUATORIAL MODE The Equatorial mode is provided for equatorial platforms or equatorial mounts both Fork and German Equatorial Mounts The configuration options allow the Right Ascension motor to start tracking when powered up at the rate specified This allows operation of the mount without a PC connected However there are many features that require a PC in order to achieve the maximum utility of the system With a PC the SiTech can Park and UnPark use PointXP to provide extremely accurate pointing for GoTo operation PEC error correction and with a high resolution mount encoder on RA using Tick Management TM the mount can be free of PEC and achieve sub arc second tracking 2 3 1 Setting Up the Equatorial Mode Using the ServoConfig software click on Edit Parameters then Auto Tracking Click on the Equatorial mode radio button Set up the Equatorial rate If you know the number of motor encoder ticks for one revolution 360 don t add sidereal of the R
326. uracy 7 2 Gurley Internal Errors 8 SiTech ASCOM DRIVER FOCUSER 8 1 DESCRIPTION OF THE FOCUSER WINDOW 8 1 1 Setpoints Tab 8 1 2 Parameters Tab 8 1 3 Temp Compensation Tab 8 2 FOCUSER OPERATIONS 8 2 1 First Time Startup WITH zero position sensor 8 2 2 First Time Startup WITHOUT zero position sensor 8 2 4 Finishing the setup for all focuser configurations 8 2 5 To Set the Setpoints 8 2 6 Startup instructions for a typical night 8 2 7 To calibrate TCF 8 2 8 Miscellaneous Focuser Notes 8 2 9 External Program control of the Sitech Focuser 8 3 EARLY VERSION OF THE SITECH FOCUSER 8 3 1 Parking and UnParking the Focuser 8 3 2 Initializing the Focuser 9 SiTech ASCOM DRIVER IMAGE PLANE ROTATOR 9 1 DESCRIPTION OF THE ROTATOR WINDOW 9 2 EARLY VERSION OF THE SITECH ROTATOR 9 2 1 Parking and UnParking the Rotator 9 2 2 Initializing the Rotator 10 SIDEREAL TECHNOLOGY RADIO HANDPAD 4 of 236 108 110 111 111 114 115 115 117 119 120 120 120 120 121 121 122 123 123 124 124 125 126 127 128 128 129 130 10 1 RF HAND PAD FEATURES 10 2 TECHNICAL INFORMATION 10 3 TECHNICAL SUPPORT 10 4 BASIC RF HAND PAD OPERATIONS 10 4 1 Mounting the Receiver 10 4 2 Connecting the Receiver 10 4 3 Transmitter LED s 10 4 4 Receiver LED s 10 4 5 Setting Address 10 4 6 Receiver address change 10 4 7 Normal Slew Pan Guide operation 10 4 8 Flashlight Operation 10 4 9 Keyboard Lock Mode 10 4 10 Turning the Handpad On 10 4 11 Turning t
327. ure the scope is unobstructed to move in any direction and be ready to press any directional button to stop the GOTO operation Selecting a nearby object in Sky Commander will minimize the initial slew Pressing any directional button 29 of 236 during a GOTO slew will stop the scope Pressing the top 2 buttons resumes the GOTO operation During initial setup and anytime the settings are in question it is wise to make sure that the encoder values displayed in the Sky Commander increment and decrement with corresponding movement of the scope While the Sky Commander does not display the current encoder positions it is possible to evaluate the encoder values with respect to movement of the scope One such method is to use Sky Commander s countdown readout for locating objects This mode essentially tells you which direction you need to move the scope and counts down the degrees 0 to 360 in azimuth and 90 to 90 in altitude First it is important to move the scope with hand pad away from the celestial pole since the values not only change rapidly but also the sign of the value changes depending on which side of the pole the scope is pointing in altitude Next get to Sky Commander s countdown mode To enter this mode select an object in the Sky Commander and press enter Next press the up arrow The upper line of the display should display values which indicate the direction that each axis needs to move and a value that
328. use Slew M82 Pause Loop Ok now we ll try to make a script that will pan the dark nebula near the Cocoon nebula 92 of 236 1 Center the telescope on the Cocoon nebula If necessary do an offset init on a nearby star first 2 Click on Add Slew 3 Click on Add Pause 4 Move the telescope to follow the dark nebula and at points of turns stop the telescope and then click Add Pan 5 Repeat Step 4 as many times as necessary 6 Click on Add Loop Here s what your result might look like Slew 21 53 43 47 18 10 Pause Pan 21 52 42 47 25 24 0 05 Pan 21 51 48 47 31 29 0 05 Pan 21 51 01 47 35 29 0 05 Pan 21 49 28 47 32 54 0 05 Pan 21 48 01 47 31 59 0 05 Pan 21 46 04 47 35 48 0 05 Loop To Record a pan relative sequence The advantage of a Pan Relative sequence is it will work the same anywhere in the sky A PanRel script probably won t be used much but there are times it may be useful One idea I can think of is for using at a public star party where each person will get to look at the moon at high power panning the terminator and or the edge Since the moon changes on a minute by minute basis if you were to use a normal Pan then the sequence would be wrong in just a few minutes however if we use the PanRel command then it will work all evening long just fine Simply move the scope before starting the script every once in a while to keep up with the lunar movement Another fun idea would be to write your
329. ust be nearest to the edge of the board If this is a Stepper system check that the ground wire is connected between the receiver and the controller Check that the Servo Stepper jumper is in the correct position Problem The receive light flickers faintly when I press keys on the transmitter The LED flashlight works properly on the transmitter Solution The transmitter and the receiver are on different addresses Please set the addresses of both units see section titled Setting Address Problem Sometimes I let up on the key but the telescope keeps moving for 1 second longer Solution This is caused by interference or a poor radio connection Occasionally you may have interference from some unknown source When you let up on a key the transmitter sends out TWO sequences to stop the telescope If radio interference interferes with both signals and both stop sequences are missed the telescope will keep moving until 1 second later it detects a lack of the next expected keep going burst and it will stop by itself Using the radio chips we ve selected this shouldn t be much of a problem If it is try mounting the receiver closer to the eyepiece and be sure it is not obscured by metal Problem I m using an Argo Navis and I press the top two buttons but the telescope doesn t GoTo It s tracking OK See the SiTech manual for other Argo Navis problems Solution Assuming you ve already been using it earlier in the evening
330. ut that is because a one terminal device wasn t available You can connect either terminal on the receiver to the ground of the stepper system When the receiver is connected to a Mel Bartels controlled system SiTech or original stepper system the 7 buttons take on the same action as the 7 buttons provided in the Mel Bartels stepper system using Scope exe Instead of a switch there is a center push button labeled SPD You can push it for 4 of a second or so and it will switch from Pan speed to Slew speed Push it again for changing from Slew speed to Pan speed The Pan and Slew LED s on the receiver will indicate which mode you re in 10 9 ARGO NAVIS amp SKY COMMANDER MODE HANDPAD OPERATION It is now possible to connect the SiTech Controller to either an Argo Navis or a Sky Commander the two operate with the same handpad controls The encoders are connected to the SiTech Controller instead of to the Argo Navis This is different than most other systems The telescope location information is passed to the Argo Navis via the serial connection There is a section in the SiTech Controller manual on setting up the Argo Navis and setting up 138 of 236 the SiTech Controller configuration The handpad operation is very simple After the SiTech Controller is connected to the Argo Navis and power is applied to them both press the top left ESC and the top right RTN keys at the same time This will initiate communic
331. ut to it for your desktop e Install the CAD program by running cslte370 exe 2 Use the CAD program to draw the shape you want to make and save in HPGL 1 format 3 Run the program HPGLToScript exe to convert the HPGL 1 file to a SitechEXE script Save the script in the Sitech folder enter the correct information in the conversion program first before performing the conversion e You can edit the script to insert the sound files to remind you to cover the scope Hat on while the scope moves between letters etc just before the pen up command and right after the move and the next Pen Down command e It s a good idea to add a pause to allow you to initially cover the scope and start the CCD camera on an image that has an integration time longer than it takes to run the script dry run the script and time it including the hat on and hat off times Then after uncovering click on unpause to start writing 4 Initialize the mount and center the target star in your CCD camera s FOV 5 Run the script The sound files will tell you when you cover and when to uncover The absolutely easiest way to get from cad to the sky is with HPGL 1 not HPGL2 152 of 236 The big drawback is most stuff doesn t support HPGL 1 anymore Ed Harvey found a free cad system that exports to HPGL 1 This solves the problem It s a bit clunky but then we re not designing the shuttle http cadstd com lite html Here s a really simple
332. uter or the Argo Navis When connected to a computer or Argo Navis the controller automatically leaves the DragNTrack SlewNTrack or Equatorial modes but it doesn t save the mode to the flash ROM If you do this you will have tracking if initialized on the celestial pole even before you connect the Argo Navis or the computer If tracking before connecting a computer or Argo Navis is not desired there is no need to initialize the controller on the celestial pole 2 2 ALT AZ SLEW AND TRACK MODE This mode is similar to the drag and track mode but is used if you don t have shaft encoders on the altitude and azimuth of the telescope To use the Slew and Track mode your Alt Az telescope must have the following features 1 A pair of servo motors to drive the telescope in altitude and azimuth 2 A handpad 3 A 12 24 volt power supply This mode uses the servo motor encoders as the telescope position You must use the handpad to slew the telescope You must select the SlewNTrack mode from the Auto Tracking tab of the Edit Parameters of the ServoConfig software You must also set up the number of telescope encoder ticks to be the same number as the number of motor encoder ticks using the ServoConfig software This is done automatically for you if you use the ServoConfig software and you click on SlewNTrack mode Important Note If your telescope has encoders for altitude and azimuth but doesn t have clutches yo
333. uth RA Scope Encoder Position Byte 16 is Keypad Status see the top of this section for a description of bits Byte 17 is Xbits Byte 18 is YBits Byte 19 is Extra bits Bit O Set if Altitude Dec motor is stopped Bit 1 Set if Altitude Dec motor is in manual Bit 2 future Bit 3 future Bit 4 Set if Azimuth RA motor is stopped Bit 5 Set if Azimuth RA motor is in manual Bit 6 future Bit 7 future Byte 20 is a 1 byte checksum of the previous 19 bytes simple addition XXR lt E gt The controller now waits for an additional 20 bytes from a host as follows Byte 0 3 New Altitude Dec Motor Position Goal least significant byte first Byte 4 7 New Azimuth RA Motor Position Goal Byte 8 11 New Altitude Dec Motor Speed Byte 12 15 New Azimuth RA Motor Speed Byte 16 Various bits Bit 0 if 0 the following new XBit and YBit values are ignored If 1 the new XBit and YBit values are used Bit 1 7 future Byte 17 New XBits value must have previous bit 0 set Byte 18 New YBits value must have previous bit 0 set 180 of 236 Byte 19 Checksum of all above data bits simple 8 bit addition If you use the above binary command to control the servo controller be sure to have a restart communication if the command gets out of sync by a communication fault If you receive a bad checksum you should resync communication by sending a few of XXS commands The flash ram values are loaded from the flash Rom to Ram on reset Both the X and Y p
334. ve PEC Collection At this point run through all of the PEC tables in the collection by incrementing or decrementing the numeric up down button You will see the black line on the graph change If there is a black line that is in bad disagreement with the others delete it by clicking on the Delete Collection Item 9 When you re happy with all PEC tables in the collection be sure to save the collection for later use Now you re ready to load the final averaged PEC table to the controller Click on the button labeled Send Averaged Table to controller 10 Be sure to save the table to flash ROM by clicking on Save Table in Controller RAM to Flash 5 2 10 PEC More Info There are two three internal PEC Table buffers in the PEC window 1 The controller buffer 2 The file buffer 3 The Averaged buffer These 3 buffers can be displayed on the graph There is a textbox which shows the status of the first two buffers Once data is in the buffers they can be loaded into the collection Every time you load a table into the collection the table is averaged and any drift is removed The filename extension for a collection is pecc The filename extension for a PEC file is pec You can save any PEC table in the collection to a file or save any of the buffers to a file except for the file buffer which comes from a file For those that are into flow diagrams of complicated processes there is a flow chart of the PEC build and implemen
335. via ASCOM so no need to click on the properties setup in the ascom windows If you want the readouts in the autofocus program to read in 1 10 000 of an inch then be sure to set the AZIMUTH Ticks pr Rev on the Focuser controller using ServoConfig to how many motor encoder ticks it takes to move the focuser inch If you want it in microns then put how many motor encoder ticks it takes to move one centimeter 123 of 236 8 3 EARLY VERSION OF THE SITECH FOCUSER Prior to Dr John McClusky building the Temp Compensated Focuser routine Dan had a simple focuser routine to control servo motors linked to focusers If you have a version of SitechEXE that is earlier than 56A you will have this earlier version of the focuser routine OUT OUT Enabl lard IN 06 DUT Jog Dist 0 0100 H Init Focuser To Stop a z Ha HaLRGE 1 3750 E 675 2 5x 2 1185 a Setpaint3 0 0000 w Setpoint4 0 0000 wj Setpoint 0 0000 4 Out Limit 2 500 In Limit 1 100 ReversalAmt 0 020 Use Focuser Use Focuser Il Hide Save window Presets Colas H 8 3 1 Parking and UnParking the Focuser When you click on SetPark for the telescope the focuser position is also remembered Now when you click on Park it will return to this position If you click on Unpark it will initialize itself for the parked position 124 of 236 8 3 2 Initializing the Focuser To initialize the focuser set it at a known posi
336. vo controller to SiTechExe the controller sends 3 items of interest to the tick management routine 1 Motor location 2 Scope encoder location 3 Motor location when the last scope encoder location happened Now have a look at the image below You ll see that it s the telescope angle radians Current Scope Tick Angle motor ticks per scope tick current motor location the location at last scope tick Pi 2 Calculated Scope Position 102 5 hoo 101 102 103 hos 105 106 107 hos 109 Scope Encoder Ticks Motor Encoder Ticks f AE TUAANA AA WUNA ELLA 1000 1010 1920 1030 1040 1050 1060 1070 1080 1090 Current Motor Position Motor Location When Last Scope Encoder Tick Axis movement gt That is how normal tick management works and it allows you to close the loop using a much more economical encoder than a sub arc second encoder Based on what Dan pulled out of one of his body parts plus some experience we think that you could have at least a 10 fold resolution increase Thus if you had an encoder that has 320 000 ticks per rev after quadrature you could use it with tick Management and have a simulated resolution of more than 3 200 000 ticks per rev This is sub arc second and should work fine for most amateur scopes There s two ways to get an encoder of this medium resolution 156 of 236 1 Gear up an inexpensive USDigital http www usdigital com The advantage is
337. with telescope ie telescope tracking on rotator tracking on If tracking starts we unpark EEEE E KE E E K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2K K K 0 06 sent to Andrew and John Ott 3 18 06 Looked into windows disappearing when loading an init file Determined to be a sky charts problem Made the Taki initialize on connection not before No telescope functions work if not connected no references to Taki unless connected Made the communication loop adjustable with the cfg TimeInterval variable Made the park unpark change color with mode added parked to messages and added yes no to setpark Made de rotator tracking to be on by default KKK K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K FK K K K K K 0 05 sent to Andrew and John Ott 3 06 06 EEEE KE E E 28 E K K E K K E 2g K K k K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2k K K KEE E KE K 2g K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K FK K K K K FK K K EEE EKE E E 28 K K K K K K K 2g K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2k K K EEEE E E E E KE K E K E E K E E E K K K K K is K K K K K K K K K k K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K 2
338. wn thing 0 50 4 8 J0 5000 ml O E Choose Setpoint Group Group 1 C Group3 gs g i Group Groun o Turn TCF on or off depending on whether the scope is focused or not The Move to focus option assumes that the absolute position of the focuser is currently exactly correct Zero focuser with Position Sensor SET Focuserto this Setpoint H9 1755 JETIMI _1650_ 0 50 4 8 0 0 1 Hide Save A A H Cot 8 1 1 Setpoints Tab MOVE Focuser to this Setpoint Left clicking the left buttons moves the focuser to that setpoint If TCF is off it is moved to the absolute position if TCF is on it is moved to the position corrected for temperature so it should be at focus Right clicking these buttons allows you to uonesuadwoy dwaj 115 of 236 change their label The Right Buttons M set that setpoint to the current EFFECTIVE position Therefore to save a new setpoint TCF MUST BE OFF Choose between four sets of setpoints for a total of 20 to choose from The button under the Setpoint Group radio buttons has two possible uses If there is no absolute zero position sensor this button sets the current position to zero If there IS an absolute zero position sensor this button causes the focuser to use that sensor to zero the focuser SET Focuser to this Setpoint While the focuser guesses which setpoint your focuser is at sometimes it may guess wrong These buttons let you tell the focuser w
339. y and press the lt SPD _ gt keys one at a time in the left to right sequence The LED s will start flashing and the 7 keys take on the value of 7 digits The keys take on the following values Now press any 3 key sequence that doesn t create a value over 254 and the transmitter is programmed You may start your sequence with one or two zero s if you like The LED will stop flashing to indicate successful change of address The address is stored in the microprocessors flash ROM 10 4 6 Receiver address change Unplug your receiver from the telescope controller Wait about 2 or 3 seconds then plug it back 134 of 236 in Within the first 10 seconds of power application press both the ESC key and the RTN key together 3 or 4 times The receiver will take on the address of the transmitter The 4 lights on the receiver make a cute flash sequence to indicate it re programmed its address It may be a good idea to make sure no others on the telescope field are powering up their receivers at this time It may also be a good idea to write your address down so when at a star party you may discuss your chosen address with all of the hopefully many other Sidereal Technology radio handpad users You may also control other folks scopes if you get them to tell you their address or use process of elimination This can make a really interesting evening of observing Sidereal Technology will not be responsible for any b
340. y changeable with a keyboard sequence This allows many users with many telescopes on the same telescope field Low Duty Cycle Transmit Time Special micro controller routine only transmits about 1 20 of the time even when a button is continually pressed There are no transmissions when no buttons are pressed This allows multiple use from several identical handpads and telescopes without interruption of any one user Instant imperceivable delay between a button press and action of the telescope This is a real plus when centering an object at pan speeds there will be no overshoot as the scope starts and stops movement at exactly the same perceived time as you press and release the key Built in Micro Processor Based astronomers LED flashlight There are 4 super bright LEDs which work in tandem The brightness is adjustable from very dim to very bright in 16 linear perceived steps The brightness is remembered across a power down Keypad lock feature When in the locked mode only the 4 direction keys work This is a great nearly mandatory feature for public star parties where the handpad is given to the general public for panning the moon at high power it also helps us more experienced observers at 3 00 AM Glow in the dark keypad A lot of research went into finding the perfect glow in the dark base and the percentage used This glow in the dark is not too bright for even the most 2 Second time expo
341. y connected to focuser Connecting to telescope SiT ech Telescope Scope Controlled by SiTech Servo Controller Sitech ASCOM Driver Yersion 1 0 By Dan Gray Successfully connected to telescope Connecting to focuser FocusSim Focuser Successfully connected to focuser Connecting to telescope SiT ech Telescope When ECU is connected to Sitechexe you will notice the small telescope ICON will no longer be gray it will be white Also on the telescope menu if you click on Show Position a round cursor will appear indicating where sitech is telling ECU it is aimed If you click on Show Coordinates the RA Dec received from Sitechexe are displayed in a small window in ECU If you click on Autotrack telescope if the telescope is slewed enough that the cursor would move off the portion of the sky being shown inECU the sky will be re drawn in ECU to include where the cursor is located If you click on Track Telescope the cursor will always be on the screen What that means is if you want to click on a target to do a GOTO and it is far enough away to not be shown on the screen when you scroll to it ECU will change the screen back to keep the cursor in view So you either need to zoom out to keep both your GOTO target in vew at the same time as the cursor or simply leave Autotrack checked and un check Track Telescope Then when you click on your target as the cursor starts moving the screen will change to include
342. you are doing photography and you have a consistent drift you can use the drift calculator Just fill in the two numbers in XX minutes drifted YY arc seconds then click Calculate You can do it for right ascension and or declination Calculating Ticks Per Rev by tracking rate If you use the drag mode and your scope doesn t track perfectly you can tweak the tracking rate with the bottom slider or type a number in the text box and re test your tracking repeating until your tracking is perfect The tracking rates will affect both the Altitude and Azimuth tracking rates If you have an equatorial mount before changing tracking rates be sure you are polar aligned 104 of 236 properly and be sure you ve entered many stars and calculated your telescope axis s errors 5 2 13 Clock Calibration At the bottom of the screen is a section on calibrating the clock in the controller After the controller and SitechEXE have been running for at least 60 minutes click on the ReSync button to adjust the controller s internal clock The default is 1 0 Then click on Save ServoCal to save the setting You should not have to do this very often unless you are REALLY bored The reasoning here is the SiTech uses the controller clock to control the scope since the PC clock can t be trusted down on the mSec level however the PC clock is much more accurate over long term So after an hour the recommended clock should be right It will screw up a run
343. you want to stop things and you won t worry about what the writing is on the left button and it s always on the left InitPoint 0 How Many Lal Star Init Right Asc 02 42 44 1211 02 Init Hour Angle RMS 00 00 00 ss Init Declination 89 1 8 08 a0 00 00 Scope Latitude Peak 00 00 00 Init Azimuth 131 12 17 95 07 59 Scope Longitude Just Load Star No Terms Init Altitude 30 36 00 AltOffset Altitude Offset Cale Only Offsets Align simple Keep Window Offset Init Up Manual automatic reece E STOP OK Cancel Control in2 sernndel GEM Scone is looking West C GEM Scope is looking East Help Colors If you stop the timer the left button changes to read Auto Init has been cancelled The countdown timer button also changes to read Simple Offset Init as shown below 51 of 236 initPoint How Many Lal Star 0 isl Init Right Asc 02 42 44 f 12 24 17 Init Hour Angle RMS 00 00 00 Init Declination 89 18 08 E 90 00 00 Scope Latitude Peak 00 00 00 Init Azimuth f 95 03 51 35 07 59 Scope Longitude Just Load Star No Terms Init Altitude 30 36 22 AltOffset Altitude Offset Cale Only Offsets Align Auto Init has Simple Load Cal been Canceled Offset Init Star No 1 E STOP Cancel GEM Scope is looking West C GEM Scope is looking East __ Help Colors The default type of Initialization is called an Offset Init The other type of Initialization is referred to as a Calibration Star Cal Star
344. z by and then their requested target suddenly appears in the center of the Eyepiece FOV Enjoy listening to them cheer lt grin gt Doing this in the Virgo Cluster is especially entertaining or build a script file to tour the cluster To close Sitech you will have to first disconnect ECU or any other ASCOM program connected to Sitech from Sitech To do this simply close ECU or better simply click on the Telescope ICON and it will disconnect and the telescope ICON will gray out Coordinate Settings ECU normally operates in J2000 and does NOT cook the coordinates So you will need to be sure to check the boxes for nutation precession and refraction in the Sitech Config pages on the Miscellaneous Tab The coordianates in the information windows do have the option to show the precessed coordinates however But do not click on this if you are about to do a Sync since it will snapshot the precessed coordinates and send them to Sitech when you do your sync and Sitech will automatically precess them again and introduce a position error So do your sync and you will notice the coordinates for ECU and the coordinates in Sitech are slightly different THEN if you want click on the Precess button in the information window and ECU will precess its coordinates for the target and they should closely match those in Sitech could this get more confusing ECU Funnies Probably the biggest funny to be aware of is to not keep up th

OperationsManual1-1

Contents

Download Pdf Manuals

Related Search

Related Contents