product manuals
Contents
1. and other package contents are accounted for It is recommended to place your fireplace near an existing wall outlet for ease of electric connection Store your fireplace in a dry safe and dust free place while drilling during fireplace installation Do not attempt to wire new outlets or circuits To reduce the risk of fire electric shock or injury to persons always have a licensed electrician perform maintenance and repairs Instructions for Use This fireplace can be operated with the switches located on the rear panel of the fireplace Plug the fireplace into a power outlet Switch I button ON to turn on the fireplace Adjust the dimming knob for the desired flame effect Turn the Il button ON for low heat Turn the Il amp III button ON for high heat Adjust the thermostat control knob to regulate the heat Operating controls The control panel on this electric flame effect heater has three switches and two adjustment knobs as illustrated below ca re ee ee I a a OFF Dimmer Knob Thermostat Knob ON OFF Press to switch the heater on or off Low Heat I Press to select 850W heat output High Heat Il Press this and the Low Heat I switch to select 1600W heat output Dimmer Knob Turn to select the desired flame effect intensity Thermostat Knob Turn to regulate the temperature see details under THERMOSTAT below Thermostat The thermostat is used to control the room temperature It acts2. use when flammable sprays solvents or glues are in use Do not run the cord under carpets Do not cover the cord with throw rugs runners or similar products Arrange the cord away from traffic areas such that it will not be tripped over by anyone Do not operate any fireplace with a damaged cord a damaged plug after the fireplace malfunctions or if it has been dropped or damaged in any manner Return the fireplace to an authorized service facility for examination electrical or mechanical adjustment or repair Do not insert fingers or allow foreign objects to enter any ventilation or exhaust opening as this may lead to an electric shock or fire or may even damage the fireplace 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 This fireplace becomes hot during use To avoid burns do not let bare skin touch hot surfaces If necessary use the handles when moving this fireplace Use this fireplace only as described in this manual Any other uses not recommended by the manufacturer may cause fire electric shock or personal injury and may void warranty privileges Always plug fireplaces directly into a wall outlet Never use an extension cord power strip surge protector multiple outlet adapter cord reel or outlet type air freshener The use of such devices creates a fire hazard Ensure the heater is not directly located under the wall outlet Faulty wall outlet connections may cause the wall outle
3. IMPORTANT INSTRUCTIONS amp OPERATING MANUAL LENOJX Floor Standing Fireplace Item No LF100 Read these instructions carefully before attempting to assemble install operate or maintain the product Protect yourself and others by observing all safety information Failure to comply with instructions could result in personal injury and or property damage Retain instructions for future reference AA amp GENERAL SAFETY INFORMATION When using this fireplace basic precautions should always be taken to reduce the risk of fire electric shock and injury to persons including the following CAUTION Due to the high temperature keep electrical cords drapery and other furnishings at least 3 feet from the front side and rear of the fireplace CAUTION HOT The heater is hot when it is in use To avoid burns do not let bare skin touch hot surfaces ON se a ee 10 11 12 13 14 15 16 17 18 19 20 21 22 Carefully read all instructions before using the fireplace and retain for future reference Remove the unit from its packaging and check to make sure it is in good condition before use Do not let children play with any parts of the packing such as plastic bags etc Check the household voltage to ensure that it matches the fireplace s rated specification Before using the fireplace carefully check the power cord and plug for any damage Be sure that the room is equipped with a workin
4. as a switch and does not vary the amount of heat output from the heater e Turn the thermostat knob clockwise until the maximum temperature setting is reached e Once the desired room temperature is reached slowly turn the thermostat knob anti clockwise until you hear a click The heater will not stop working e The heater will turn on and off automatically maintaining the room temperature you have set Auto Safety Shut Off Mechanism e This fireplace is equipped with a safety shut off feature which initiates if the fireplace overheats e g Due to blocked air vents For safety reasons the fireplace will NOT automatically reset and will need to be manually turned ON e To restart the fireplace unplug the fireplace from the power outlet for at least 15 minutes Next reconnect to the power outlet and turn on the fireplace Troubleshooting Check if the unit is plugged in the power outlet Unit does not work does not heat Check if the unit is in Standby mode If so turn the unit ON Check if the heat is turned OFF Check for safety cut off operation Check if the unit is plugged in the power outlet No flame effect Check if the unit is in Standby mode Turn the unit ON Replacing the Light Bulb e This fireplace consists of 2 bulbs E 12 40W that illuminate a flame effect The light bulbs need to be replaced if you notice a dark section of the flame or when the flames lose clarity e Warning Always disconnect from the power
5. g smoke detector Before unplugging the power cord turn off the power When touching the unit keep your hands dry to prevent electric shock Do not place the fireplace near curtains or other inflammable objects Keep combustible materials such as pillows bedding papers clothes and curtains at least 3 feet away from the front side and rear of the fireplace Ensure the unit is not blocked and there is spacing of at least 50cm around its sides and at least 120cm from the front Do not block air intakes or exhaust in any manner to prevent fire Do not use on soft or uneven surfaces like a bed where openings may become blocked Do not place the heater on long pile carpet or rugs Ensure the heater is placed on a level surface with enough clearance from its surroundings Exhibit extreme caution when any fireplace is in the vicinity of children and infants Never leave children or infants unattended while the fireplace is on or plugged in When not in use switch off and always unplug the fireplace Prevent water from entering the housing of the fireplace during operation or while in storage Always store the fireplace in a dry area free from any moisture This fireplace is not intended for use in bathrooms laundry areas or similar indoor locations Never place the fireplace where it may fall into a bath tub or get exposed to water in any way Do not use in places where gasoline paint or other flammable liquids are used or stored Do not
6. location to another The unit does not contain any serviceable parts inside Do not attempt to open and repair the unit yourself All components should only be serviced by a qualified technician Getting Started e Remove the fireplace from the box e Remove the packaging Place it inside the box or safely dispose elsewhere Package Contents e Electric Fireplace e Instruction Manual Features e Floor standing electric fireplace e Contemporary amp portable design e Dual heat settings 850Watts 1600Watts e Realistic wooden log flame effect e Flames operate with amp without heat Adjustable flame brightness 1400 Watts Built in overheating protection auto safety shut off Cool touch housing No assembly or hardware needed Simply plug amp heat Quick Reference Guide Prior to installation please ensure that the voltage and capacity of your power outlet is compatible with your fireplace Your fireplace may emit a slight harmless odor during its first use This odor is a normal reaction caused by the initial heating of internal fireplace parts and it will not occur again It is normal for fireplace to make a rattling sound for a short duration of time during its first use If your fireplace does not emit heat please ensure the fireplace switch is on For further information please refer to the Troubleshooting section of this manual Helpful Advice before Installation Please retain all packaging until all the parts
7. outlet before removing bulbs to reduce the risk of fire electric shock or damage to property e Warning The bulb reaches high temperatures during operation Allow it to cool down before replacing it e Access the bulb panel located on the rear panel of the fireplace see figures below Tt a BULB OVER i FIG 4 7 FIG 2 ao e Access the bulb by removing the four screws located on the back panel e Replace the bulb with a new one Extra caution should be taken because the bulb can be hot e Close the panel lid using screws e Warning Do not use fireplace without properly putting the lid back in place e The light bulb may only be replaced by the manufacturer or qualified service agent Cleaning amp Maintenance e Swatch off and disconnect from the power supply before attempting any maintenance or cleaning in order to reduce the risk of fire electric shock to persons or damage to property e Warning Always disconnect from the power supply before cleaning fireplace e For general cleaning use a soft clean duster Never use abrasive cleaners The glass viewing screen should be cleaned thoroughly with a soft cloth Do NOT use proprietary glass cleaners e Be careful not to touch the heating elements Do not allow any water or any other liquid to enter the housing or control panel e Always keep the air inlet and outlet openings free from any dust or fluff use a vacuum cleaner fitted with a dusting brush to rem
8. ove accumulated dust when necessary Do not probe any opening to remove dust or fluff Storage If the heater is not in use for a long period pack the heater and user manual into the original box and store in a cool dry and well ventilated place Technical Specification e Supply 240V 60Hz e Rated Power 1600W e Bulb 2x 40W E14 LENODX Lenoxx Electronics Aust Pty Ltd Importers and Wholesalers of Electronics and toys 6 Oban court Laverton North Victoria 3026 ABN 97 844 321 851 PH 03 9267 2100 FAX 03 9267 2199 For service call 1300 666 848 Email lenoxx lenoxx com au www lenoxx com au
9. t to overheat Be sure that the fireplace plug properly fits into the outlet before each use During use make sure the fireplace plug does not overheat If necessary have a qualified electrician check and or replace the wall outlet Do not place the fireplace near a bed for objects such as pillows or blankets can fall off the bed and be ignited by the fireplace Never clean this fireplace while it is plugged in To disconnect turn control to OFF then remove the plug from the outlet Never pull the cord Always hold the plug firmly and then remove from the outlet This fireplace is intended for supplemental heat and or decorative purposes Continuous use for several hours can impact the performance and life of the fireplace It is not intended to be used in commercial industrial or agricultural settings Do not use outdoors Do not use the heater with a timer or separate remote control system This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Close supervision is necessary when the product is used by or near children or invalids Children should be supervised to ensure that they do not play with the appliance Do not leave the heater running unattended Always disconnect the unit when moving it from one
Download Pdf Manuals
Related Search