MOBILE CALL GSM Alarm System
Contents
1. Operation Instructions System status There are 4 status as following Arm defense zone 1 99 will alarm when detectors are triggered Home Arm in arm status the defense zone which is set as Home Arm will alarm when detectors are triggered Disarm defense zone 1 99 will not alarm when detector triggered except 24 hours defense zone System setup status In this status all defense zones will not alarm when detectors are triggered Remote Controller Operation Users can use remote controller to set system as Out Arm Home Arm Emergency Alarm Real time Disarm and etc Out Arm Press button Disarm Press ew button Home Arm Press 7 button Emergency Alarm Press A button system will alarm at once Home Arm It means for the safety while somebody is at home you need to enable the peripheral door window balcony and boundary detectors of the alarm system while prevent from triggering the indoor detectors which may cause improper warning then you shall select Arm at Home let just part of the detectors work and disable the other parts 15 Main Unit Operation Press At Home button on keypad Remote Control Operation Press ir button on remote controller LCD display OutArm It means to guard use while everyone is going out all the detectors of the fost are always working when the detector is triggered by detecting source anti theft fire prevention gas leak etc the alarm system will sound th2. AA indicates the hour of the setting time BB indicates the minute of the setting time For example set the arm time as 55 7am Operating method 33 gt 22 gt 45 gt LCD display ooo 3 Timing Control In setup status use keypad to input 39 then input the number indicating turning on timely arm disarm 1 0 and then input to confirm You will hear a long beep and a voice prompt setting completed The factory default is off Operating method 39 gt 0 1 gt 0 turn off the function of timely arm disarm 1 turn on the function of timely arm disarm For example turn on the function of timely arm disarm Operating method 39 gt 1 gt E Time Setting of Out Arm Delay Default 60 sec In setup state input the command 44 XX XX indicates the delay time of out arm XX 01 99 1 sec to 99 sec Note The setting is effective only with the panel keyboard operation The operation by remote controller or SMS is immediate arm without delay E Time Setting of Alarm Delay Default 40 sec In setup state input the command 45 XX XX indicates the delay time of alarm XX 01 99 1 sec to 99 sec 10 Note The setting is effective only when a zone is set as Alarm Delay Zone Note Before the system enters arm or alarm status it will emit a Di sound per second E Alarm Number Setting In setup state input 51 56 then input the voice alarm receivi
3. effective 24 hours Gas alarm yes Emergency button effective effective 24 hours Emergency alarm no Zone 7 99 invalid Emergency alarm Wired defense zone 93 99 invalid Emergency alarm Siren sound time 180 sec Home Appliance Components List Main panel 1 pc Remote controller 2 pcs Siren 1 pe PIR sensor 1 pc Door sensor 1 pc Power adapter 1 pc User manual 1 pe 21 Care and Maintenance The alarm system has excellent design and uses advanced technologies It shall be used with care The following suggestions are required to maintain your obligations under the warranty terms and for prolonging the service life of the system Place the control panel and all parts and accessories out of children s reach lt gt Keep the alarm system dry Rain humidity and various fluids or moisture all will corrupt the electronic circuit Do not use or place the alarm system in dirty locations otherwise the electronic elements will be damaged Do no place the system in excessively hot locations High temperature will shorten the service life of electronic equipment damage batteries deform or even melt some plastic parts Do not place the system in excessively cold locations Otherwise condensation many occur and damage the circuit board of the alarm system It is recommended that you check and test the alarm system periodically Check the main unit every three months 1 Whether it can arm disarm normally 2 Whet
4. system returns to disarm State Operating method x gt E Factory Reset In disarm status use keypad to input 95175308246 and press to confirm all the LED indicators will be on for 2 seconds and you will hear a long beep The main unit gets all its settings cleared and restores to its factory settings successfully Operating method 95175308246 E Coding of Remote Controller Extra remote controller has to be code to the alarm host in order to perform normally The one in the standard package has been coded In setup state use keypad to input 20 input the remote controller number 1 8 and then press to confirm The main unit emits a long beep and you will hear remote control coding The 8 indicator is on without flashing press any button on the wireless remote controller the main unit makes a long beep and you will hear coding completed 8 indicator goes out indicating the remote controller succeeds in coding Operating method 20 gt A gt A indicates 1 8 remote controllers number You can add maximum 8 remote controllers LCD display amp E Delete Remote Controller The remote controller can t control the main unit after it s deleted In setup state use keypad to input 21 then input the remote controller number 1 8 and then press to confirm The main unit emits a long beep and the Signal indicator flickers once You will hear a voice prompt delete co
5. 2 disarm if finished successfully you will hear a voice prompt System disarmed Press 3 monitoring for 30 seconds to continue monitoring press 3 again to monitor for another 30 seconds Press 4 two way intercom for 30 seconds You can t operate the main unit during this time E Emergency Help Press Emergency button on keypad or 6 button on remote controller or wireless panic button the main unit will alarm and make call to the preset user numbers E System Dialing Function In disarm status you can use the main unit to make any call just like a land line telephone Dial telephone number on keypad press 9 button the main unit will make a beep and the Signal indicator will be flashing After the call press CH button again the main unit will be in disarm Status Alarming Record Checking In disarm state input 0 then the main unit will make a long beep and enters the state of alarm record checking After displaying the alarm and defense zone number indicator the LCD screen will display the exact alarming time of this defense zone Press 2 you can upturn to check the previous alarming record press 8 downturn to check and press to exit checking For example the 51st defense zone the 7th alarming alarming time 12 10 August Ist 2008 LCD display for one second 18 and then display the alarming time s l 200 D Ll i L ken wm wm mm wm wm we You can also check
6. MOBILE CALL GSM Alarm System User s Manual Profile For a better understanding of this product please read this user manual thoroughly before using it Function Instruction 7 wired and 99 wireless defense zones LCD screen with time clock display Voice prompt for all operations 3 groups of timely arm and disarm Can store 6 phone numbers when alarming system will make alarm call to these numbers automatically Can store 3 SMS numbers when alarming system will send alarming SMS automatically 10 second automatic message recording Built in artificial intelligent digital voice announcer Built in artificial intelligent English message Users can make calls by using keypad on alarm panel just like a telephone One key control function Out Arm Home Arm Remote Arm Arm disarm by SMS or call remotely SOS fire gas door hall window balcony and boundary places alarm Real time delay 24 hours bypass defense zones programming function Wireless coding easy to add additional wireless accessories Remote control Arm Disarm Monitor and Intercom by phone SMS alert for power failure or recovery Built in AAA NI HI rechargeable battery make alarm when power off Alarm Host Diagram In order to make the main unit get the wireless signal well for all wireless accessories please put the alarm host at the central place of your defense area Make sure it s away from large metal objects and househ
7. akage Window Alarm Door Alarm 505 Hall Alarm Balcony Alarm Boundary Alarm Function Settings Initialization Please insert SIM card and plug in power adaptor and then power on the system all the LED lights will be on for 2 seconds and you will hear a long beep the system comes into initialization After the time clock displays on the LCD screen the SGM starts flashing and the main unit starts to detect the GSM network until a long beep Then the SGM indicator goes out indicating the system comes into disarm status Finally turn on the backup battery switch E Enter Settings In the state of disarm input 4 digit password by the keypad on the main unit and press button to confirm You will hear a voice prompt please enter instruction At the same time SET indicator is on without flashing and 0000 displays on the screen indicating the system enters setting status You can perform different settings repeatedly as long as the system keeps in setting status The system will exit setting mode and return to disarm status if you don t press any keypad button for 40 seconds Note In setting status press EN can delete the numbers input The system default password is 8888 Operating method XXXX gt 5 X indicates the new 4 digit password LCD display l l iL J E Exit Settings Press and buttons the main unit emits a long beep and exits settings The SET indicator goes out and the
8. cessfully Operating method XX gt YY YY gt XX indicates address codes of message receiving numbers from the first group to the third group 57 59 YY YY indicates the SMS receiving number For example setup 13822222222 as the first SMS receiving number Operating method 57 gt 138222222 gt E Delete SMS Receiving Number In setup state use keypad to input 57 59 and then press button to confirm The main unit will make a beep the Signal indicator will flicker once and you will hear delete completed which indicate SMS number is deleted successfully Operating method XX gt XX indicates address codes of message receiving numbers from the first group to the third group 57 59 For example delete the first SMS user number from the system Operating method 57 gt E SMS Notification for Arm Disarm Default OFF In setup state input the command 77 1 0 1 ON 0 OFF After starting this function the system can send SMS to three SMS receiving numbers 57 59 as mentioned above when the system enters arm disarm status through wireless remote controllers or its panel keyboard operation 12 E Defense Zone Programming If you want to change the alarm attribute of defense zone such as turn off the siren when system alarms you can do it by defense zone programming In setup state first input 60 then the defense zone number 01 99 then input def
9. e alarm Press Out Home button on keypad system will make a beep per second and totally 100 beeps The OUT ARM indicator will be on without flashing It means Out Arm is set successfully Arm Operation Press Out Home button the system will enter arm status 100 seconds later LCD display 20 A If 200 l Ip l L a You can also set out arm by SMS remotely The SMS command is Remote Control Password Default 1234 1 After the setting the host makes a Di sound ARM LED is on and you will receive a SMS System armed E 8 Disarm It means to stop the alarm when the main unit sounds the alarm or make the alarm system in the state of non warning After disarming even if you trigger the detector the main unit would not sound alarm excluding 24 hour defense areas Use keypad to input system password then press button Out Home or At Home lights will be off It means disarm setting successful Remote Control Operation Press CR button on remote controller Main Unit Operation input system password LCD display r You can also set disarm by SMS remotely The SMS command is Remote Control Password Default 1234 2 After the setting the host makes Di Di sound ARM LED is off and you will receive a SMS System disarmed Note If you send arm or disarm SMS by the mobile phone number stored in the system before refer to SMS Receiving Number Sett
10. ed Operating method 32 gt AA gt BB gt CC gt DD gt EE gt FF gt AA indicates the last 2 digits of the present year BB indicates the 2 digits of the present month CC indicates the 2 digits of the present date DD indicates the 2 digits of the present hour EE indicates the 2 digits of the present minute FF indicates the 2 digits of the present second For example set the time as 15 35 40 Oct Ist 2009 Operating method 32 gt 09 gt 10 gt 01 gt 15 gt 35 gt 40 gt Timing Settings 1 Timely Arm In setup status use keypad to input 33 35 then input the hour AA and minute BB of the time you want to set to arm and finally input to confirm You will hear a long beep and a voice prompt setting completed Operating method XX gt AA gt BB gt XX indicates the address code 33 34 35 of the timely arming AA indicates the hour of the setting time BB indicates the minute of the setting time For example set the arm time as 45 10pm Operating method 33 gt 22 gt 45 gt LCD display a aaa 2 Timely Disarm In setup status use keypad to input 36 38 then input the hour AA and minute BB of the time you want to set to disarm and finally input to 9 confirm You will hear a long beep and a voice prompt setting completed Operating method XX gt AA gt BB gt XX indicates the address code 36 37 38 of the timely disarming
11. ense zone type 1 4 then input defense zone location number 1 8 and then select siren on off 0 1 at last press to confirm You will hear the main unit emit a long beep and a voice prompt setting completed Operating method 60 gt AA gt B gt C gt D gt AA defense zone number 01 99 means zone 1 to zone 99 B defense zone type 1 real time defense zone 2 40 seconds delay defense zone 3 24 hours defense zone 4 bypass defense zone C defense zone location 1 SOS Alarm 2 Fire Alarm 3 Gas Leak Alarm 4 Door Alarm 5 Hall Alarm 6 Window Alarm 7 Balcony Alarm 8 Boundary Alarm D siren ON OFF 0 OFF 1 ON For example set defense zone 12 to be 24 hour fire alarm and siren on Operating method 60 gt 12 gt 3 gt 2 gt 1 gt E Home Arm Defense Zone Setting If you want some detectors work and some do not you can use Home Arm function In setup state use keypad to input 61 then choose the corresponding defense zone number 01 99 then choose Home Arm and then choose whether alarm 0 1 button and finally press to confirm The main unit will make a long beep and a voice prompt setting completed Operating method 61 gt XX gt A gt XX indicates 01 99 is defense zone 1 to defense zone 99 A indicates 0 Home arm but not alarm 1 Home arm and alarm 13 For example set defense zone 11 to be Home arm and alarm Operating me
12. her it can dial the number for alarm normally 3 Whether it can receive wireless detectors signal normally 4 Whether the back up battery can work normally Check the wireless detectors once a month 1 Trigger wireless detectors to see if system can alarm normally 22 2 Check all detectors batteries to see if it s in low voltage 3 Check whether wireless detectors can send signal to the main unit normally Check the SIM card 1 Check the use of SIM card such as network signal balance etc 2 Make sure the PIN code verification of the SIM card is closed 3 Please keep the password and SIM card number safe in case that other people remote control the system illegally Since the alarm system is continuously in operation or standby mode the supply adaptor of the control panel shall be connected to a safe and reliable socket Do not place the system near your bedroom or office table because the siren will make high loudness sound in the case of alarm which may adversely affect your rest or work If the alarm system will not be used for a long time please disconnect the system from the power supply Se Please do not disassemble repair or alter the products without permission or it may cause accidents and faults lt gt Do not drop this product on the ground or on hard objects as it may lead to massive impact to cause faults and damages lt gt Without approval and consent of relevant authorities p
13. ing you will receive two arm disarm SMS E Answer Alarm Call When the main unit sounds alarm it will dial the preset numbers If no one answers the call the system will call the next user number automatically The system will call each preset numbers for 3 times in order If you answer the call you will hear the pre record voice You can set system via your telephone or mobile phone keypad If you hang up directly without answering the call the system will call each preset number for 3 times circularly Press Read the alarm information Press 1 Main unit stops alarming and Arm it stops calling users Press 2 Main unit stops alarming and Disarm it stops calling users Press 3 Siren off and monitors the scene for 30 seconds for continued monitoring press 3 again to monitor for another 30 seconds Press 4 Main unit starts a 30 second two way intercom It cannot be controlled by the mobile during the time of intercom E Remote Control Dial the number associated to the alarm main unit by phone mobile phone and after one ringing cycle you can hear a voice prompt Please 17 enter password If the password is right you will here Press 1 to arm Press 2 to disarm Press 3 to Monitor Press 4 to Intercom If the password is wrong you will hear a prompt voice wrong password please re enter Press 1 arm if finished successfully you will hear a voice prompt System armed Press
14. lease do not set 110 119 or the alarm phone number of police station for this main unit Please read the suggestions above carefully and follow the instructions herein If any of the equipment does not work properly please send it to the dealer or authorized service point for repair We will try our best to 23 solve the problem for you as soon as possible The following sensors are optional d Ca Wireless Outdoor Signal Repeater Wireless keypad Siren with flash i Wa Bet Glass Sensor Panic Button Remote Controller el sd Wireless Smoke Gas Detector Wireless Pet Detector Immune PIR Detector Optional sensors detectors are packed separately You can choose according to your specific requirements Typical house configuration Pe External Sirens Door window d Garage II d Der ef b DT d d d Smoke a PIR Movement Detector x Detectors
15. mpleted Operating method 21 gt A gt A indicates 1 8 remote controllers number a Coding of Defense Zone Wireless detectors have to be coded to the main unit in order to trigger it alarm The wireless PIR and door sensor in the standard package have been coded In setup state use keypad to input 23 input the defense zone number you want to code 01 99 and then input to confirm The main unit emits a long beep and the corresponding defense zone is displayed on the screen You will hear a voice prompt detector coding Then trigger a wireless detector to emit a wireless signal after receiving the signal the main unit makes a long beep and you will hear coding completed the I indicator goes out at the same time Operating method 23 gt XX gt XX indicates 01 99 defense zones number LCD display i tee m m mg I i j E Delete Defense Zone The wireless detector can t control the main unit after it s deleted In setup state use keypad to input 24 then input the defense zone number you want to delete 01 99 and then input to confirm The main unit emits a long beep and the defense zone indicator flickers once You will hear a voice prompt delete completed Operating method 24 gt XX gt XX indicates 01 99 defense zones number 7 WR Change Password 1 Change Operation Password Operation password is the password used to disa
16. ng number mobile number or telephone number and then press to confirm The main unit will make a long beep the Signal indicator will flicker once and you will hear setting completed which indicate voice alarm receiving number is set successfully Operating method XX gt YY YY gt XX indicates the 1 6 alarming user number 51 56 YY YY indicates voice alarm receiving phone number For example set 13811111111 as the first voice call number Operating method 51 gt 13811111111 gt LCD display Set L E Delete Phone Number In setup state input 51 56 and then press to confirm the main unit will make a long beep and the Signal indicator will flicker once and you will hear delete completed which indicate the alarming user number is deleted successfully Operating method XX gt XX indicates the 1 6 alarming user number 51 56 For example Delete the third alarming user number from the system Operating method 53 gt LCD display j E SMS Receiving Number Setting SMS Receiving number means when system is alarming it will only send SMS to this mobile number You can set maximum 3 SMS numbers In setup state input 57 59 then input the SMS receiving number and then press button to confirm The main unit will make a beep the Signal indicator will flicker once and you will hear setting completed which indicate setup suc
17. old appliances which may cause high frequency interference as well as barriers such as reinforced concrete wall or fire door etc Alarm Panel front schematic diagram Power Oh COCE Me 7 Home D MOBILE CALL ALARM Functions Indicator i Cre DE mg emm tas ia Namie Cut Arm ypad SA ce cr Home Am EELE A 2 H D ais Mile e ass sess Alarm Siren TETT 4 5 b er Hi ETIT gt z a T KITO Emergency E o EN SRR RRR RR RR RR RR all out DC 12W ep Lead wit Sa Wire Conmector PCB Panel e Wired terminal block Pte lf s Positive of speaker red cable a ae Negative of speaker black cable 2 N Wired sensor 1 support both NO and NC e es Wired sensor 2 support both NO and NC Wired sensor 3 support both NO and NC 8 GND GND 9 Zoned Wired sensor 4 support both NO and NC Wired sensor 5 support both NO and NC 15 Zone T Wired sensor 7 suppor both NO and NC sr Nepean ea Note 1 LB and LB are to connect external speaker If you think the internal speaker is not loud enough please contact us for professional speakers 2 Connect one cable of the wired sensor to GND and the other to LALA wth 3 Please pay attention to the siren connection Do not mix the two cables together when connecting Otherwise it will damage the transistor in the main panel LCD display Alarm pE G ERSGEKECCD n e De rb e eee et rn Fire Alarm Gas Le
18. rm or remote control In setup status use keypad to input 30 then input the 4 digit new password and then press to confirm The main unit will make a long beep and you will hear a voice prompt setting completed Operating method 30 gt XXXX gt XXXX indicates the new 4 digit password For example change the system password to 1012 Operating method 30 gt 1012 gt LCD display E i P j 2 Change Program Password Program password is the password you should input in order to setu the system In setup status use keypad to input 31 then input the 4 digit new password and then press to confirm The main unit will make a long beep and you will hear a voice prompt setting completed Operating method 31 gt XXXX gt XXXX indicates the new 4 digit password For example change the system password to 2846 Operating method 31 gt 2846 gt LCD display Note the operation password and the programming password can not be set as the same number E Clock Setting In setup status use keypad to input 32 then input the last 2 digits AA 8 of the present year the two digits BB of the month the two digits CC of the date the two digits DD of the hour 24 hour system the two digits EE of the minute the two digits FF of the second and finally enter to confirm You will hear a long beep and a voice prompt setting complet
19. the alarm records by SMS Max Latest 9 records SMS Check Command Remote Control Password Default 1234 3 Reply SMS Eg Alarm record NOI Zone 05 TIME 11 06 25 11 37 It indicates the first record wireless zone 5 alarm time NO9 Zone 19 Time 11 06 25 11 45 It indicates the first record wireless zone 19 alarm time GSM Signal Checking Before installing the main unit you should check the signal of the installing place in order to ensure the unit can perform well In setup state input 81 gt the main unit will make a long beep and display 00 XX XX indicates the intensity of the signal And the intensity should be within the range of 07 31 if it s less than 07 you should change place For example if the signal intensity is 12 it will display as l l KEE E e Es H 19 E Note Only under Out Arm status the system has the function of sending SMS alert for power failure power recovery While in Disarm or Home Arm status it does not The SMS content Power failure Power charger off Power recovery Power charger on Technical Parameters E List 1 Input Voltage Standby Current Alarming Current Wireless Frequency GSM Frequency Back up Battery Siren Volume E List 2 Alarm Defense Zone Arm Home Arm Type Information DC12V 1A lt 55mA lt 450mA 315 433MHz PT2262 EV 1527 4 7MQ 900 1800 1900MHz NI HIAAA 6 DC7 2V 110dB 20 es Zone 6 effective
20. thod 61 gt 11 gt 1 gt For example set defense zone 12 as Home arm but not alarm Operating method 61 gt 12 gt 0 gt E Voice Recording In setup state use keypad to input 701 and then press to confirm The main unit will emit a beep and the d indicator is on and after 10 seconds countdown recording starts record at 30cm away from the main unit with moderate tone 10 seconds later the main unit will make a beep indicating the recording stops and the recorded voice will replay Operating method 701 gt LCD display E Siren Setting In setup state use keypad to input 75 in the operation of arm disarm by remote control select if the siren sounds or not by 0 1 button and then press to confirm The main unit will emit a long beep and a voice prompt setting completed Operating method 75 gt A gt A indicates 0 Siren off 1 Siren on System default 0 Siren off For example set siren on when arm disarm Operating method 75 gt 1 gt LCD display fie E Siren Setting in Emergency Help mode In setup state use keypad to input 76 and then 1 0 finally press 14 to confirm The main unit will make a long beep and a voice prompt setting completed Operating method 76 gt A gt A indicates 0 siren off in Emergency Help mode 1 siren on in Emergency Help mode System default 0 siren off
Download Pdf Manuals
Related Search