LCP-102 User Manual
Contents
1. CK OF PRODUCT WARNING APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS SUCH AS VASES SHALL BE PLACED ON THE APPARATUS WARNING THE MAIN POWER PLUG MUST REMAIN READILY OPERABLE CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK GROUND ING OF THE CENTER PIN OF THIS PLUG MUST BE MAINTAINED WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPRATUS TO RAIN OR MOISTURE WARNING TO PREVENT INJURY THIS APPARATUS MUST BE SECURELY ATTACHED TO THE FLOOR WALL RACK IN ACCOR DANCE WITH THE INSTALLATION INSTRUCTIONS This product is AC only MO t ADN Important Safety Instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an ele2. MS mode as described in Panel Mode Selection on page 3 Select one 1 of the four 4 setup pages as described in Page Select on page 3 Tap the specific key encoders to select one 1 of the 16 assignable displays currently not being used Turn the encoder to scroll through the list of intercom ports o RON Tap the encoder to select the intercom port The selected intercom port is now assigned to the display 6 Repeat step 1 through step 5 as needed To cancel or clear an assignment do the following 1 Tap either assignment encoder knob The display goes blank 2 Tapthe encoder knob once again The display returns to showing dashes indicating no assignments TRIMS Mode Operation For each assigned display turn the upper encoder under the display to change the input level Turn the lower encoder to change the output level Turning an encoder one 1 notch in either direction displays the current level Further rotation changes the level PAP Mode Assignments and Operation In PAP mode you set up IFBs and then adjust the level from the defined program input to the defined IFB output PAP Mode Assignment To assign PAPs to the LCP 102 do the following 1 Run AZedit and define the output port for each IFB you want to set up then send changes to the intercom system NOTE For each IFB you can define or change the input port either from the intercom system configuration software or from the LCP 102 but you
3. P e CDP To select the LCP 102 panel mode do the following Turn the ADDRESS KEY encoder until SERVICE appears Tap the ADDRESS KEY encoder Turn the ADDRESS KEY encoder until SET MODE appears Tap the ADDRESS KEY encoder Turn the ADDRESS KEY encoder to until the desired mode Trims PAP or CDP appears Tap the ADDRESS KEY encoder to select the panel mode desired Ox OY Be US cS Page Select Within each panel mode there are four 4 setup pages of assignments available Each page lets you setup 16 assignments You can then switch between pages to view settings or make changes To select pages do the following Turn the ADDRESS KEY encoder until PAGE SEL appears Tap the ADDRESS KEY encoder Turn the ADDRESS KEY encoder until PAGE appears Tap the ADDRESS KEY encoder Any assignments already configured for the page appear in the display window Otherwise the display show dashes Bo SINR m You are now ready to setup assignments on the newly selected page Refer to the following paragraphs that apply to the currently selected panel mode TRIMS Mode Assignments and Operation TRIMS Mode Assignments and Operation In TRIMS mode you assign individual ports of the intercom system to display and then adjust the input and output trims This is the same as adjusting the analog input output gains in AZedit TRIMS Mode Assignment To configure TRIMS mode assignments do the following Place the LCP 102 in TRI
4. RT Digital Matrix Intercom Innovating the Future of Communications Model LCP 102 Level Control Panel Up to and including version 1 0 User Manual 9350 7623 000 Rev E 5 2010 Proprietary Notice The product information and design disclosed herein were originated by and are the property of Bosch Security Systems Inc Bosch reserves all patent proprietary design manufacturing reproduction use and sales rights thereto and to any article disclosed therein except to the extent rights are expressly granted to others COPYRIGHT NOTICE Copyright 2010 by Bosch Security Systems Inc All rights reserved Reproduction in whole or in part without prior written permission from Bosch is prohibited WARRANTY NOTICE See the enclosed warranty card for further details CUSTOMER SUPPORT Technical questions should be directed to Customer Service Department Bosch Security Systems Inc 12000 Portland Avenue South Burnsville MN 55337 USA Telephone 877 863 4169 Fax 800 323 0498 Info rtsintercoms com Technical Questions EMEA Bosch Security Systems Technical Support EMEA http www rtsintercoms com contact_main php RETURN SHIPPING INSTRUCTIONS Customer Service Department Bosch Security Systems Inc Lincoln NE Telephone 402 467 5321 Fax 402 467 3279 Factory Service 800 553 5992 Please include a note in the box which supplies the company name address phone number a person to contact regarding the repair t
5. ator eye level when standing or sitting to permit easy access to the front panel controls and displays Connections System connections are summarized in Figure 2 Cable diagrams are shown in Figure 4 to Figure 9 When connecting a UIO 256 GPIO 16 frame along with the LCP 102 you have a choice of two 2 methods e Using LOOP connector of the LCP 102 e Using a Y cable If you have several LCP 102 s connected in a chain you can connect the UIO 256 GPIO 16 to the LOOP connector of the last LCP 102 in the chain or you can insert it anywhere in the chain with a Y cable Whichever configuration you use you can also connect three 3 additional UIO 256 GPIO 16 frames to the first UIO 256 GPIO 16 in a ring configuration as illustrated in the UIO 256 GPIO 16 User Manual Connections CONNECTIONS FOR A SINGLE LCP 102 OR MULTIPLE LCP 102 5 ZEUS J26 ZEUS J26 Cronus J4 Cronus J4 ADAM CS J902 ADAM CS J902 XCP ADAM MC J3 ADAM XCP ADAM MC J3 ADAM DATA DATA LCP 102 LCP 102 ADDR 1 LOOP LOOP DATA LCP 102 ADDR 2 LOOP T FIGURE 2 Connection example for a single LCP 102 or multiple LCP 102s ZEUS J26 ZEUS J26 CRONUS J4 CRONUS J4 ADAM CS J902 ADAM CS J902 XCP ADAM MC J3 ADAM XCP ADAM MC J3 ADAM DATA LCP 102 UIO 256 GPIO 16 DATA J2 LOOP J2 LCP 102 UIO 256 GPIC Loop FIGURE 3 Connection example of an LCP 102 connecting to a UIO 256 GPIO 16 Two 2 methods for
6. connecting a UIO 256 GPIO 16 with the LCP 102 up to three 3 mor UIO 256 GPIO 16 frames may be connected to the first UIO 256 GPIO 16 in a ring configuration as described in the UIO 256 and GPIO 16 User Manuals Connections DE 9P DE 9S Male Female ZEUS J26 l TO LCP 102 CRONUS J4 DATA XPC ADAM MC J3 ADAM FIGURE 4 Interconnect cable from a Zeus Cronus or ADAM intercom system to the LCP 102 DE 9S DE 9S Female Female ott ate 1 gt lt 2 2 gt 1 TO ADAM CS TO LCP 102 J902 DATA FIGURE 5 Interconnect cable from an ADAM CS intercom system to the LCP 102 DE 9P DE 9P Male Male ZEUS J26 TP TO UIO 256 CRONUS J4 J2 XPC ADAM MC J3 i ADAM a DE 9S Female TO LCP 102 DATA FIGURE 6 Y cable for connection of an LCP 102 and a UIO 256 GPIO 16 to a Zeus Cronus or ADAM intercom system DE 9P DE 9S Male Female 7 a cL 7 2 r 1 12 TO SECOND LCP 102 FIGURE 7 Cable to interconnect two LCP 102s All intercom systems DE 9S DE 9P Female Male TO ADAM CS i TO UIO 256 J902 EE J2 DE 9S TO LCP 102 DATA FIGURE 8 Y cable for connection of an LCP 102 and a UIO 256 GPIO 16 to an ADAM CS intercom system DE 9P Male 7 2 y TO UIO 256 GPIO 16 TO LCP 102 LOOP 12 FIGURE 9 Cable to connect UIO 256 GPIO 16 to the LCP 102 All intercom systems Power Up and Ini
7. ctrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 1 1 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 1 4 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped LCP 102 Description ee pied 3 Specifications MC A 4 Location and Mounting er I aeaa J CONNEC OMS ii 5 Power LH and Initial Settings een 8 APPLYING ROWER EE 8 PROGRAMMING MENUS 5 o RIO Sass RO UD Ea rp AEN A Da AA RRG 8 SETTING THE PANEL ADDRESS pibe e n EE Ure e EAR een A nee EKRA AAE ee erba nha ATARE 8 ADJUSTING THE DIMMER siiis ied REGE ei A RHENO EHE ED GU ROGER DRE EBERT URGE nee 9 Panel Mode Selection 11 o A RR ER tiende A A
8. displays 2 Tap the ADDRESS KEY encoder once DIMMER appears in the menu display 3 Turn the ADDRESS KEY encoder until SET ADDR displays 4 Tapthe ADDRESS KEY encoder once ADDR 1 appears in the menu display 5 Tapthe ADDRESS KEY encoder to select ADDR 1 for the first LCP 102 This stores the setting and all displays show asterisks for a few moments Then all displays show dashes 6 Double tap the ADDRESS KEY encoder to exit programming mode when finished Otherwise the LCP 102 automatically exits after 10 seconds NOTE The address setting is retained in the LCP 102 memory when power is removed 7 Repeat step 1 through step 6 to set addresses on additional LCP 102s select ADDR 2 ADDR 3 for the third for the second LCP 102 and so on Power Up and Initial Settings Adjusting the Dimmer To adjust the dimmer do the following 1 Turnthe ADDRESS KEY encoder until SERVICE displays 2 Tapthe ADDRESS KEY encoder once DIMMER appears in the display window 3 Tapthe ADDRESS KEY encoder again One 1 or more right pointing arrowheads appear 4 Turn the ADDRESS KEY encoder to increase or decrease the brightness of the arrowheads 5 Tapthe ADDRESS KEY encoder to save changes All displays flash asterisks at the new brightness level and then returns to normal operation Power Up and Initial Settings CHAPTER 1 Operation Panel Mode Selection The LCP 102 has three 3 panel modes e TRIMS e PA
9. dtm dre A 11 TRIMS Mode Assignments and Operation id ae 12 TRIMS MODE ASSIGNMENT sonic A a i eene le bla rai 12 PAP Mode Assignments and Operation sse cnn rro nnr nan 12 PAP MODE ASSIGNMENT suscitan ta tes RASE EESO EEA SDE a Haan een nee ic di seis 12 PAP MODE OPERATION ii A A iia 13 CDP Mode Assignments and Operation u A A Ai 13 CDP MODE ASSIGNMENTS cent act re HE eI eed eo Po ERA RUE de N Pet er E decane ERRARE Pedo ce eaa ca eg Lab Ra ep eene airis 13 CDP MODE OPERATION ERN EE a ii os 13 S ving Configu r tion Changes TEE 14 A E E AE EENE A IE ANE ESATE AANE EN E A ENN 15 List of Figures FIGURE 1 LCGP 102 Reference VA A AA Ai a E AEE 4 FIGURE 2 Connection example for a single LCP 102 or multiple LCP 102s sss 6 FIGURE 3 Connection example of an LCP 102 connecting to a UIO 256 GPIO 16 sss 6 FIGURE 4 Interconnect cable from a Zeus Cronus or ADAM intercom system to the LCP 102 s 7 FIGURE 5 Interconnect cable from an ADAM CS intercom system to the LCP 102 sss 7 FIGURE 6 Y cable for connection of an LCP 102 and a UIO 256 GPIO 16 to a Zeus Cronus or ADAM intercom system 7 FIGURE 7 Cable to interconnect two LCP 102s All intercom systems ssssssssssesee eee 7 FIGURE 8 Y cable for connection of an LCP 102 and a UIO 256 GPIO 16 to an ADAM CS intercom IC NBI IRI 7 FIGURE 9 Cable to connect UIO 256 GPIO 16 to the LCP 102 All intercom sys
10. he type and quantity of equipment a description of the problem and the serial number s SHIPPING TO THE MANUFACTURER All shipments of product should be made via UPS Ground prepaid you may request from Factory Service a different shipment method Any shipment upgrades will be paid by the customer The equipment should be shipped in the original packing carton If the original carton is not available use any suitable container that is rigid and of adequate size If a substitute container is used the equipment should be wrapped in paper and surrounded with at least four 4 inches of excelsior or similar shock absorbing material All shipments must be sent to the following address and must include the Proof of Purchase for warranty repair Upon completion of any repair the equipment will be returned via United Parcel Service or specified shipper collect Factory Service Department Bosch Security Systems Inc 8601 East Cornhusker Hwy Lincoln NE 68507 U S A Attn Service CAUTION THE LIGHTNING THE FLASH AND CAUTION TO REDUCE EXCLAMATION ARROWHEAD THE RISK OF ELECTRIC POINT WITHIN WITHIN THE SHOCK DO NOT THE TRIANGLE TRIANGLE IS A IS A WARNING REMOVE COVER NO WARNING SIGN USER SERVICABLE SIGN ALERTING YOU PARTS INSIDE REFER ALERTING YOU OF SERVICING TO OF IMPORTANT DANGEROUS QUALIFIED SERVICE INSTRUCTIONS VOLTAGE PERSONNEL ACCOMPANYIN INSIDE THE i G THE PRODUCT PRODUCT SEE MARKING ON BOTTOM BA
11. must always define the output port first using the intercom system Place the LCP 102 in PAP mode as described in Panel Mode Selection on page 3 Select one 1 of the four 4 setup pages as described in Page Select on page 3 Tap the encoder knob under one of the currently unused assignable displays to enter IFB assign mode Turn the encoder knob to scroll through the list of IFBs Tap the encoder knob once to assign the IFB to the display assignment o m Roo NOTE If you already assigned the input port for the IFB using the intercom system configuration software you can skip step 5 and 6 7 With the display showing the name of the IFB tap the encoder knob The LCP 102 enters input port assignment mode The scroll list of intercom ports appear in the display CDP Mode Assignments and Operation 8 Turn the upper encoder knob to select the intercom port where the program source for the IFB is connected 9 Tap the encoder to assign the selected port The display shows the IFB name and the IFB is completely set up 10 Repeat step 5 and step 6 to make further assignments To cancel or clear an assignment do the following 1 Tap either assignment encoder knob The display goes blank 2 Tapthe encoder knob once again The display returns to showing dashes indicating no assignments PAP Mode Operation To change the program level do the following gt Turn either encoder knob Turning the encoder knob o
12. n notch in either direction displays the current level Further rotation changes the level CDP Mode Assignments and Operation In CDP mode you use each display and its encoders to assign one 1 intercom port to any party line Then during operation you can adjust the level at which that port hears the party line audio CDP Mode Assignments To assign CDPs to the LCP 102 do the following Place the LCP 102 in PAP mode as described in Panel Mode Selection on page 3 Select one 1 of the four 4 setup pages as described in Page Select on page 3 Tap the encoder knob under one of the currently unused assignable displays Double tap either encoder knob to access a scroll list of intercom ports Turn the encoder knob to locate the intercom port you want to assign to a party line Tap the encoder knob to select the intercom port Tap the encoder knob again to access the scroll list of party lines Turn the encoder knob to locate the party line you want to assign the intercom port to f o n 9o gg ww Tap the encoder knob This assigns the port to the party line as a talker listener and the name of the port reappears in the display window 10 Repeat step 1 through step 9 To cancel or clear an assignment do the following 1 Tap either assignment encoder knob The display goes blank 2 Tapthe encoder knob once again The display returns to showing dashes indicating no assignments Saving Configuration Change
13. s Specifications Loop Connection for connection to additional Displays and Controls for each of 16 Assignments Mode Indicators Menu Display Menu Selector LCP 102s and or UIO 256 GPIO 16 DATA Connector for connection to the intercom system FIGURE 1 LCP 102 Reference View Specifications Dimensions rcs exc 2 RU 19 W 7 L Weight ito sa 8 20 lbs Power Consumption coooococnccnocncoconononnnonnon cono nonnnonncnnnns 13 Watts Fused Power Entry Module with On Off switc 100 240VAC 50 60Hz Data Connector DB 9 Male lup Common PAD a Ea Data o ieni ET E E E E R E N A Inu HO N A Pin da A N A MED MPH M N A Pin Yes Data nup M BS N A Pin O N A lug e Common P n D aise EEE Data A E E AR EE E AS N A A e EEE EE EERE N A Pt EO T T N A O TA N A Pe Data TA N A lgup N A CHAPTER 1 Installation Location and Mounting The LCP 102 occupies two 2 rack spaces in a standard 19 inch equipment rack or bay and is 7 25 inches 184 2mm deep behind the front panel including the rear panel connectors There are no special ventilation requirements The LCP 102 should be mounted at or near oper
14. s CDP Mode Operation To change the listen level for a port do the following gt Turn either encoder knob one 1 notch in either direction to display the current level Further rotation changes the level To display the party line the port is assigned do the following gt Tapeither encoder knob once The party line displays for about four 4 seconds and then the port name reappears Saving Configuration Changes The settings for address current panel mode and current setup pages are saved in LCP 102 and are kept if the power turns off All display assignments and level settings are uploaded to the intercom system and become part of the online configuration This configuration is retained if there is a loss of power to the intercom system However if you wish to have a backup copy of your settings save the settings to disk using your intercom system configuration software Notes Notes
15. tems CHAPTER 1 Introduction NOTE The LCP 102 is not compatible with the CS9000 Series intercom systems For information on how to complete the configuration of some features see the AZedit user manual LCP 102 Description The LCP 102 combines the features of an analog trim panel a CDP Camera Delegate panel and a PAP Program Assign Panel in a single frame 2 rack units You can easily switch between three 3 panel modes and make rapid configuration changes using the menu selector on the front panel In each mode you can make up to 64 assignments and then adjust the assignment levels For example e In Trims mode you can assign and adjust the analog input and output trims for up to 64 intercom ports n PAP mode you can select the program input source and set its level for each of 64 IFBs e n CDP mode you can assign up to 64 intercom ports to any combination of party lines and then adjust the listen level for each participant on that party line The LCP 102 connects to the auxiliary data port of any ADAM ADAM CS Cronus or Zeus intercom system Also it has a loop connector for connection to an auxiliary device such as another LCP 102 or a UIO 256 GPIO 16 frame Since a single LCP 102 provides trim adjustments for 64 ports only one 1 unit is required to completely configure an ADAM CS or Zeus system For larger ADAM intercom systems up to 15 additional LCP 102 frames can be connected via the loop connector
16. tial Settings Power Up and Initial Settings Applying Power During a normal power up the alphanumeric displays first show asterisks After a few moments some assignments may appear in the displays above selected keys depending upon whether or not anything was previously assigned using the intercom system configuration software If there are currently no assignments the displays show dashes If the LCP 102 connected to the intercom system cannot establish communication with the intercom system all LCP 102 displays continue to show asterisks In this case check the cable from the first LCP 102 to the intercom system and verify the intercom system is operational NOTE If more than one 1 LCP 102 is used set the addresses using the programming menus as described in Programming Menus Programming Menus The LCP 102 Programming Menus are accessed using the ADDRESS KEY The menus are summarized in Table 1 TABLE 1 The LCP 102 Programming Menus PAGE SEL Menu Items SERVICE Menu Items Page DIMMER Page 2 SET ADDR Page 3 SET MODE Page 4 VER Setting the Panel Address Before programming any assignments each LCP 102 should be set to a unique panel address as follows NOTE Each programming step should be performed within approximately 10 seconds Otherwise the LCP 102 automatically cancels the procedure To set the address for the LCP 102 do the following 1 Turn the ADDRESS KEY encoder until SERVICE
Download Pdf Manuals
Related Search