Speed Dome Camera Controller Operation Manual
Contents
1. Function Transfer the camera to the position of No N preset position 4 Cancel the Preset position PRESET N OFF Display Preset No 001 Description N No of preset position from 1 to 128 Function Delete the No N Preset position stored 5 Set the cruise track Minking A01 B01 PELCO P PELCO D ALEC Ultrak Available Enter the status of track setting SHOT N ON N No of track from 1 to 6 Display Track 01 Sum 06 Description Track Nol is currently set in which there are 6 preset points Edit Track Press TELE to edit afterward and press WIDE to edit return Each track involves 16 preset points and the running speed and the dwelling time of each preset position Display No 01 Point 001 Description The Ist preset position in the track is 01 Display No 01 Speed 001 Description The speed of the Ist preset point in the track is the 1st class Display INo 01 Time 004 Description The dwelling time of the 1st preset point in the track is 4 seconds Speed Range 1 to 8 from the fastest to the lowest Any speed outside the range well be referred as the Ist class the range of the dwelling time is 1 to 99 When the No N preset point is set as No 0 then all preset points before the No N preset point in the track will be valid however all numbers of preset points afterward and their speed and dwelling time2. multiple speed dome cameras figure5 Figure 4 ALM ALM DC IN GND Rt R VIDEO VIDEO PEED 1 ALM ALM DC IN GND RF R VIDEO VIDEO OME SPEED N OO Od OOOO oo0o00000 HOCOO000O Figure6 Figure5 3 Connections between the keyboard and the speed dome camera Figure6 4 The keyboard controls the Multiplexer directly Figure7 VI oo o VIII Figure7 Technical Specifications Communication between Speed Dome Camera and Controller Port to multi port and half duplex function Communication connector RS 485 Baud Rate of Communication Four baud rates i e 2400Bps 4800Bps 9600Bps and 19200Bps Distance of Communication 1200 M in maximum Power Supply DC12V 800 mA Size 380 X 165 X 80 mm Weight 2 Kg Number of Controlled Speed Dome Camera up to 32 Points for Attention Please read the operation manual of the keyboard carefully before using it The operation manual is mainly focused on all functions of B01 Protocol For other different protocols operations could be something difference and those different parts will be listed on Supplementary Description of the Keyboard Controller in details The keyboard takes 12V DC power supply Please confirm the voltage and polarity before the power supply is switched on Do not place the keyboard under the rain or on wet place so as to avoid short circuit or electrical shock As the keyboard is a sophisticated electronic de
3. to the ending scan position operation AUTO OFF Run Auto Pan AUTO ENTER Auto Pan operation takes the following parameters You must set these parameters before using a Auto Pan command to begin the scan operation You can use the scan stop command ot PT scan stop command to stop the scan Setting scan condition Auto Pan Position First specify position second specify position Auto Pan Speed and Direction 10 Stop Auto Pan AUTO OFF Only Minking A01 B01 Available or push the joystick to stop scan 11 Control the zoom of the Camera WIDE TELE 12 Control the Focus of the Camera FAR NEAR 13 Control the Iris of the Camera OPEN CLOSE 14 Auxiliary Control of the Camera By combination of F1 and ON OFF buttons you can set some data of the camera and functions are listed as follows operations of NEON Protocol No of Definition of Keyboard Operation Control Object Value N F1 N ON F1 N OFF Power ON OFF Recover Initial 0 Camera power supply reset control Per Switching Values of Camera 1 Back Light Compensation ON OFF Zero Illumination refer to function of N OFF camera Menu Display refer to function of 3 ON OFF camera 4 Digital Zoom ON OFF 5 Back Light of Keyboard Screen ON OFF 6 Focus Automatic Manual 7 Iris Automatic Manual 8 Automatic Manual 9 White Balance Mode WB Indoor Mode Outdoor Mode 10 A
4. ELCO D 2400Bps ON z Cm Cm oC CE C oC EE wo aS er PELCO P 4800Bps C NCEE So gt C Sz E nC C oC EE PELCO P 9600Bps A ON 1 S om oC om coL EE PANASONIC 9600Bps t Ultrak 9600Bps s g rf 2 3 4 6 d Switching control between intelligent decoder and multiplexer The keyboard can be operated in two modes Intelligent Decoder and Multiplexer When power supply is on it is operated on the default mode of Intelligent Decoder Press F3 down until the LCD disply CONTROLLING MULX then control the processor by the RS 232 output of the keyboard Attention If the LCD is not the right state the Multiplexer can not be under of control V Operation of the Keyboard 1 Select Address of Speed Dome Camera Decoder CAM N Enter Display Current CamID 001 Description N No of camera from 0 to 255 EE VC wom SE oi om C coL oC C coL EE Function Select the address of the camera to be controlled When the value N is in conformity with the address of the speed dome it will be under control 2 To set preset position PRESET N Enter Display Preset No 001 Description N No of preset position from 1 to 128 Function Store current position and refer it as No N position 3 Call the Preset position CALL N Enter Display Call Number 001 Description N No of preset position from 1 to 128
5. II Introduction of Functions Select Camera 0 255 Joystick Control Control pan tilt direction and speed of the holder Lens Control Control the focus zoom and iris of the camera Operation of Preset Position 1 128 Set Preset Position Call Preset Position Operation of Cruise Track 1 6 Set Cruise Track Run Cruise Track Automatic Horizontal Scan Control of dome including speed and direction of scan Self Learning Track of Intelligent Speed Dome Function Setting of Menu of Speed Dome Control of Multiplexer Direct Control on Decoder Control front devices such as the decoder etc Ill Introduction of the keyboard Panel 1 The Sketch of the Front Panel and Description of Buttons Figure 1 There are speed joystick buttons and LCD on the front panel of the control keyboard The display is used to show the status of the system as well as operation information The joystick controls the upward downward leftward and right ward speed motion of the speed dome The description of buttons is as follows ON OFF as LIVE TAPE OPEN CLOSE AUTO FARNESR WIDE TELE SYSTEM KEYBOARD Figure 1 Func 1 cam Set special function of the system together with other buttons Zoom Fullscreen Show picture of the camera in full screen PIP up arrow Show picture of the
6. RA R i aN Da 4 All settings of the menu could not be lost DITA E i even power failure occurred v 5 Operations under special case can be referred Figure3 on the description of the menu of the ball machine 15 Use the Joystick to Control the Speed Dome Camera You can use the speed joystick to control the Pan Tilt direction and speed of the dome of the camera randomly The speed of pan tilt is decided by the angle of the joystick you operated Figure 3 Change the tilting angle of the joystick you can adjust the speed evenly and the camera can be focused automatically in the course of scan to keep images being distinct 16 In case error operation occurs normal display will be recovered after Error Operation appears for 1 second VI Installation and Connection Attention Please read the operation manual of the keyboard and the speed dome carefully before connecting wires Any incorrect connections can cause O O P z RED O O GREEN permanent damage of the device When connecting wires first switch off the O o BLACK YELLOW power supply of all devices The communication wires between devices should O O be shielded twisted cable When installing cables they should be far away from RED RS485 high voltage lines or other possible interference circuits as can as possible BLACK RS485 GREEN GND 1 The marking of wires of the transfer box Figure 4 YELLOW RS232 OUT 2 Connections of the keyboard controller controlling
7. Speed Dome Camera Controller Operation Manual Please read this operation manual before using this device and use the device properly Also please keep this manual with care to ensure easy access at any time I Brief introduction The keyboard controller is used for terminal receivers such as the intelligent Speed Dome and the decoder etc Taking the EIA RS 485 electrical interface between the keyboard and the receiver one keyboard can control as much as 32 speed dome and decoders without driving the bus and the maximum communication distance between the keyboard and the receiver is up to 1 2 km It s very easy for operating and setting the Speed Dome Camera The controller is also to control the terminal receiver to achieve the function of controlling pan tilt lens and ect Main Functions Set the address range of the dome camera and the decoder 0 255 Control all functions of the dome camera such as Power ON OFF To operate the pan tilt of Speed Dome Camera moving in different speed lever Set or call the set points and cruise tracks of the dome camera Altogether 128 preset points and 6 cruise tracks can be set Each track involves 16 preset position and the dwelling time and call speed upon each point can be set as well Manually or automatically control the dome camera and change the leaving settings of particular camera by call the menu of the camera Manually control the focus zoom and iris of the camera
8. TW Mode One Push WB 11 Black amp White Color Switching Color Black amp White 12 Set Auto Pan Only conditions for scan If lt 180 low speed gt 180 low speed 13 start scan operate as Item 6 in this lt 180 middle speed gt 180 middle speed 14 paragraph lt 180 high speed gt 180 high speed 15 Reserved 16 Reserved 17 Reserved 18 Reserved For different camera control functions in the list could be different For the camera with the menu switch ON OFF the menu by F1 3 ON and switch ON OFF the OSD by F1 3 OFF In case the camera has the menu and the menu is ON 1 Select the item on the menu by buttons WIDE TELE to scroll the cursor up or down 2 Chang the status of the selected item on the menu by buttons FAR NEAR 3 Switch OFF the menu as per operations in the list after the menu is set Take care of differences between the Menu of Speed Dome and the Menu of Camera For the speed dome with the menu enter the menu by CALL 64 Enter and basic operations are as follows 1 Call No 64 preset point to open the main menu by the control keyboard 2 When the menu appears on the screen move the cursor to the item you need to set by TILT UP and TILT DOWN and enter the settings of the item to make change by PAN LEFT and PAN RIGHT 3 Speed up operation of the joystick after N h K keeping it for one second in one direction
9. camera in PIP mode Picture in Picture 2X2 down arrow Show picture of the camera in 4 frame 3X3 deft arrow Show picture of the camera in 9 frame 4X4 right arrow Show picture of the camera in 16 frame Live Show live picture of the camera at current mode Tape Playback pictures Function Tape Playback video information of VCR CAM Select address of the intelligent Speed Dome or multiplexer CALL To call the preset position PRESET To set the preset position SHOT To set up or call cruising track TIME Set time for special function AUTO To control auto horizontal rotation for pan tilt WIDE To a wide angle TELE To turn to a telescopic range FAR To make focus far manually NEAR To make focus near manually OPEN To open iris CLOSE To close iris ON Switch on the setting of function OFF Switch off the setting of function F1 F2 Auxiliary control buttons F3 Switching control between intelligent Speed Dome and Multiplexer 0 9 Number key CLEAR To clear inputted data ENTER To confirm 2 Rear Panel Figure 2 fe Pee DC12 POWER ID CODE CONTROL OUTPUT O e 8 Figure 2 A Power input connector input DC12V power B ID Code switch Used to set the protocol in use and the baud rate of communications C Communication connector RS485 The controller is connected to adapter box by specific cable IV Setting of the Keyboard a The protocol in use and the baud rate
10. of communication of the keyboard are set by the ID Code in Figure 2 DIP1 DIP4 are used to select type of the communication protocol as per following table means the protocol is available Normal Baud Selection of Protocols Integrated Type of Protocols Rate Protocol DIP1 DIP2 DIP3 DIP4 DIPS5 DIP6 Minking A01 OFF OFF OFF OFF ON OFF Minking B01 ON OFF OFF OFF OFF ON Santachi OFF ON OFF OFF OFF ON PELCO D ON ON OFF OFF OFF OFF PELCO P 4800Bps ON OFF OFF OFF ON OFF PELCO P 9600Bps OFF ON PANASONIC ON OFF ON OFF OFF ON Longcomity OFF ON ON OFF OFF ON O HUNDA600 ON ON ON OFF OFF ON LILIN OFF OFF OFF ON OFF ON VICON ON OFF OFF ON ON OFF MOLYNX OFF ON OFF ON OFF ON O KALATEL ON ON OFF ON ON OFF VCL OFF OFF ON ON OFF ON O Reserved ON OFF ON ON OFF ON O ALEC OFF ON ON ON OFF ON Ultrak ON ON ON ON OFF ON b DIPS and DIP6 are used to select the baud rate shown as following table DIP7 and DIP8 are not used tatus of ID Code ee DIP1 DIP2 DIP3 DIP4 DIP5 DIP6 DIP7 DIP8 Baud Rate 2400bps OFF OFF 4800bps ON OFF 9600bps OFF ON 19200bps ON ON c Some of the ID Code of the protocols are set as follows ATT 234567 1 8 Cm MinKing B01 9600Bps ON 1 Cm Cm if MinKing A01 4800Bps i A A 2 5 6 ON 1 C wo os P
11. shall be set as 0 automatically After tracks are edited press OFF to store and exit while push the joystick to exit without storage 6 Tour the Track SHOT N Enter Display Input Tour No 01 Description N No of the track from 1 to 6 Function Tour the No N track and stop tour by pushing the joystick 7 Stop the Track SHOT N OFF Display Input Tour No 01 Description N No of the track from 1 to 6 Function Stop the No N track or stop tour by pushing the joystick 8 Cancel Cruise Track SHOT N OFF Pressing OFF down until Clear Tour OK appears Display Input Tour No 01 Description N No of the track from 1 to 6 Function Delete the No N track 9 To turn on Auto Pan Operation of NEON SAMSUNG Protocol AUTO P1 ON P2 OFF Display Input 1st No 001 Description P1 the starting scan No of preset point from 1 to 128 which should be set already Display Input 2nd No 002 Description P2 the ending scan No of preset point from 1 to 128 which should be set already If P1 P2 or P1 and P2 are coincided the speed dome will make scan in range of 360 Note For PELCO D PELCO P Protocol the way of operation is as follows Set the starting scan position Transfer the Speed Dome to the starting scan position operation AUTO ON Set the ending scan position Transfer the Speed Dome
12. vice you should never open the case so as to avoid the occurrence of trouble The keyboard has integrated multiple protocols and you are pleased to select correct protocol and the baud rate When switching on power supply take care of the selected protocol and the baud rate on the first screen In case the keyboard controls the Multiplexer the operation of combination buttons is as follows Press one button first and press the other button after release the first one For example When enter exit setting of the menu Function Zoom press Function button first and press Zoom button after Function button is released In case the keyboard controls the multiplexer the operation of combination buttons is as follows Press one button first and press the other button after release the first one While use Function alone please put it down until Motion Detect OK appears When the keyboard controls the Multiplexer please refer to concerned operation manual of Multiplexer
Download Pdf Manuals
Related Search