AEC-931A2BS Motion Sensor Twin Light with Warning
Contents
1. Smart GUARD User Manual AEC 931A2BS Motion Sensor Twin Light with Warning Message Table of contents ICONS OP PpaCk ace i niin rusian naomi Page 1 2 Smartguard Motion Light with Video Camera 6005 Page 3 ASS 0016 hi eee ener tee eee ne rere tre ore nr rer te rere era nrc Ret Tre rrr mies Page 3 Eh LS Cal PNET OTA Eee dan At ne Page 4 5 Programming your Smartguard soora E Page 7 6 Technical SpeCi li Cations ananas rame i aa Page 8 7 General Information and Safety Page 9 STC CCMA O essee a TE Page 10 Contents of packaging Smartguard Motion Light with Video Camera User Manual 2pc 100W JCD G8 bulb Accessory bag 2pcs screws 2pcs plastic masonry plugs wall mount cross bar 3pcs wire nuts User manual are kept in one zip bag please keep these accessories Smart GUARD Smartguard JCD G8 bulb User Manual ScrewD w Screws Plastic Wall Mount Wire nuts Masonry plugs Cross Bar Smartguard Motion Light with Video Camera overview Floodlight cover 15 Halogen bulb gt LA C0 50 2 Q PIR lens Fig 1 Step 1 Assembly 1 Install replace the halogen bulb see fig 3 M 8 Make sure to unplug unit or turn off power first M Remove floodlight cover by twisting cover anticlockwise M If replacing a bulb take out th2. Daytime and nighttime light and speaker are all in operation Mode 2 Suggested for day to day use Light at night speaker in the daytime Daytime light is off speaker 1s on Nighttime light is on speaker is off Mode 3 Perfect for a place of business Light at night speaker at night Daytime light 1s off speaker 1s off Nighttime light is on speaker is on Audio mode for selecting which audio message will play when motion sensor detects movement Pre set default is You are trespassing Push one time for Warning You are being videotaped by a security camera Push again for dog barking Push one more time to turn off this function Technical Specifications 1 Features and specification PIR detection angle 180 Deg and detection range up to 32 8 t Powered by AC 100V to 240V subject to requirement Halogen bulb JCD G8 100W 2 Auto light sensor Sensitivity control Floodlight time delay control General Information and safety Special care instructions The Smartguard Motion Sensor Twin Light is designed to be weather resistant Never attempt to immerse the unit in water or any other liquid This will damage the unit and void the warranty This product is designed to illuminate and make verbal announcements It will not prevent the commission of any act legal or illegal The manufacturer assumes no liability for any damage to property injury to person or
3. Installation to a junction box using crossbar mount see fig 5 amp fig 6 l 2 3 4 Attach the crossbar part no to junction box and fix by screw C Feed the cable through the back mounting plate Fix the mounting plate to crossbar part no by screw D Connect the black wire live wire from the AC power cord to the single black wire coming from Smartguard using one of the supplied wire nuts part no Connect the white wire from the AC power cord to the white wire coming from Smartguard using one of the supplied wire nuts part no Connect the green yellow wire from the AC power cord to the 2 ereen yellow wires coming from Smartguard using one of the supplied wire nuts part no Make sure the polarity is correct Attach the unit to the mounting plate You will first need to angle the unit back so that the catch at the top of the mounting plate fits into slot on the back of the unit Next lower the unit until holes at the bottom of the mounting plate and unit are flush Then screw screw A into this hole tightening carefully Fig 5 ScrewA Fig 6 Installing your Smartguard Motion Light with Video Camera on surface without a junction box see fig 6 amp fig 7 l Place plastic masonry plugs part no into desired surface aligning holes as shown below Using an electric screwdriver fasten mounting plate directly to surface using screw
4. death Remove dirt or stains with a soft cloth dampened with water or neutral detergent Keep the Smartguard Motion Sensor Twin Light in a dry and cool dust free environment or container when it is NOT used Do not open the Smartguard Motion Sensor Twin Light with for unauthorized service This could cause serious damage to the unit and will void the warranty This Smartguard Motion Sensor Twin Light is a precision electronic device Do not attempt to service this unit as opening or removing covers may expose you to the danger of electric shock or other risks To avoid risk of burns due to high temperature do not touch the floodlight when it is turned on CAUTION FCC Information This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Warning Changes or modification to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limited for Class B digital device pursuant to Part 15 of the FCC Rules Their limits are designed to provide reasonable protection against harmful interference 1n a residential installation This equipment generates uses and can
5. e existing halogen light bulb part no M Putin new 100 Watt maximum JCD G8 bulb part no M Replace floodlight cover Caution Never touch the bulbs with your bare hands Always use a clean cloth when handling the bulbs Fig 3 Step 2 Installing the Smartguard Motion Light with Video Camera IMPORTANT IF INANY DOUBT ABOUT THE INSTALLATION OF THIS PRODUCT CONSULT A QUALIFIED ELECTRICIAN This product must be grounded Do not mount the unit against inflammable surfaces The motion detector will not operate correctly if it is installed Near the outlet of a central heating boiler Near air conditioning plant Pointing directly at moving vehicles Within sight of reflections from moving water Where other lamps could shine on the detector BEFORE ATTEMPTING ANY INSTALLATION OR MAINTENANCE ENSURE THAT THE ELECTRICAL SUPPLY IS SWITCHED OFF AND THE CIRCUIT FUSES REMOVED OR THE CIRCUIT BREAKER IS IN THE OFF POSITION Please make sure the voltage and polarity are correct before connection Incorrect voltage may cause electric shock If you are not sure please contact your retailer Note It is recommend to mount Smartguard Motion Light with Video Camera 6 7ft above the ground for optimum performance do not mount the fixture below 3 94ft See below figure for details of performance range Detection range 32 8ft x 180 see fig 4 6 56 13 12 19 69 26 25 32 8 Fig 4
6. radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If the equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 10
7. s E part no Feed the cable through the back mounting plate Connect the black wire live wire from the AC power cord to the single black wire coming from Smartguard using one of the supplied wire nuts part no Connect the white wire from the AC power cord to the white wire coming from Smartguard using one of the supplied wire nuts part no D Connect the green yellow wire from the AC power cord to the 2 oreen yellow wires coming from Smartguard using one of the supplied wire nuts part no Make sure the polarity is correct Attach the unit to the mounting plate You will first need to angle the unit back so that the catch at the top of the mounting plate fits into slot on the back of the unit Next lower the unit until holes at the bottom of the mounting plate and unit are flush Then screw screw A into this hole tightening carefully Fig 7 Please allow 1 minute warm up time after switching on Step 3 Adjusting the Settings see fig 8 9 E Time control Turn the time control knob to side to increase the illumination time 7 minutes max turn the control knob to side to reduce the illumination time 30 seconds min Fig 8 E Sensitivity control Adjust the detector range of Passive Infrared Motion Sensor 6 56ft 32 8ft E Selecting working mode Mode 1 Suggested setting when out of town Light speaker all day detection
Download Pdf Manuals
Related Search