here. - Mendor Discreet in UK
Contents
1. The cover with the sealing rim Position 1 Position 2 Position 3 Position 4 Covers closed top cover up top cover up top cover up STEP 5 Adjusting date and time settings starting and bottom and bottom and bottom To adjust the date and time settings please see chapter Settings in the User manual position cover closed cover down cover further Do not use the meter before you have adjusted the date and time for dispensing down for The meter is ready for use after these settings have been adjusted J a test strip 3 priming the uh gt OF D am lancet B Performing a blood glucose measurement T T L Ub aaa Please follow the stepwise instructions below on how to perform a blood glucose measurement umes ene al oe STEP 1 Preparation for the measurement a N 1 Always measure with clean hands We recommend washing your hands with soap and warm water Ta i D A 2 Change a new lancet into the blood glucose meter before every time you measure the blood glucose l g 3 Open the top cover position 2 Q STEP 2 Dispensing a test strip y A Pull the bottom cover down fig 16 until the te2. 3 If required you can re prime the lancet and repeat STEP 4 if the blood sample is insufficient after the first lancing e m NOTE If the bottom cover is not completely closed it cannot be detached O A i Slide down to R Slide down to remove top NOTE Please note that the release latches have to remove bottom cover be slid all the way down for proper release of the Shor eel G eee covers fig 4 a Position 3 top cover up and bottom cover down Lancet trigger button m P ASS ey A STEP 2 Inserting the Mendor Discreet test strip cartridge 1 Open the protective aluminium coated bag of the test strip cartridge by tearing the corner of the bag open Use scissors if necessary 2 Pull the cartridge container lid slightly sideways fig 5 after which the lid will open downwards 3 Slide the test strip cartridge in fig 6 making sure that the a Cartridge label and meter s display face the same direction b arrows point towards the meter 4 Close the cartridge container fig 7 and put the covers back on the meter mendor DISCREET m Ny j _ gt a 7 ra STEP 5
3. Measuring 1 Move the finger so that the tip of the test strip touches the blood drop and fills the test strip fig 19 Analysis of the blood sample starts automatically 2 The test result is shown on the display in 5 seconds fig 20 SSS ve oeaan ROT 39 puaw E 19 STEP 3 Inserting the lancet and adjusting the lancing depth 1 Slide the top cover up and remove the bottom cover please see STEP 1 b 2 Firmly pull the lancet holder out of the meter fig 8 3 Insert the new lancet into the lancet holder Hold the base of the lancet holder fig 9 and push the new lancet through the lancet holder until it is fully inside the lancet holder fig 10 Leave the thin disposable cap attached until you have adjusted the lancing depth and have attached the lancet holder back inside the meter 4 To adjust the lancing depth twist the outer part of the lancet holder There are four 4 penetration depths available min and max Illl fig 11 The desired penetration depth should face with the semi circle on the inner part of the lancet holder 5 Refit the lancet holder on the meter so that the visual indicators match semi circle shapes on the front of the meter and arrows on the back of the meter fig 12 6 Remove the cap of the new lancet by simply rotating and pulling it fig 13 STEP 6 Removing the test strip 1 Remove the used test strip by pulling it out fig 21 and
4. haa mendor DISCREET Mendor Discreet blood glucose meter Quick guide A Setting up the meter Thank you for choosing the Mendor Discreet blood glucose meter Please follow the stepwise instructions below on how to set up the meter before use After these steps the meter is ready for use The meter does not need to be calibrated as it calibrates automatically when the test strip cartridge is inserted Functions and positions of the covers rotect the meter and the test strips inside Iln addition to that the covers enable operating the meter The covers on the meter are there to Pulling down the bottom cover dispenses the test strip and primes the lancet The four basic positions of the covers are shown below and they are later referred to in this quick guide The covers have four positions fig 1 STEP 4 Refitting the top and bottom covers 1 Refit the covers back on the meter fig 14 and 15 The bottom cover does not have a sealing rim and is positioned its longer edge facing the back of the meter The top cover has a sealing rim and is positioned with its longer edge facing the front of the meter NOTE Close the covers properly for transporting and storing the meter mendor
5. st strip comes out position 3 At this point the meter powers on automatically STEP 3 Priming the lancet Pull the bottom cover even further down position 4 fig 17 This step primes the gt lancet The bottom cover returns to position 3 automatically when you stop pulling the bottom cover STEP 1 Removing the covers To remove the top cover nT To remove the bottom cover with the sealing rim b without the sealing rim 1 Slide the top cover up position 2 1 Make sure that the bottom cover is comp 2 Turn the meter over While sliding the l letely closed position 2 before sliding the left right release latch down pull the top cover release latch down off The top cover detaches from the meter 2 While sliding the left release latch down pull fig 2 the bottom cover down The bottom cover I detaches from the meter fig 3 NOTE The meter won t turn on automatically if there is no test strip cartridge inside the meter N or the cartridge is empty i J i J Y STEP 4 Taking a blood sample 1 Press your fingertip firmly against the lancet holder fig 18 2 Press the lancet trigger button to release the needle
6. the meter turns itself off automatically Do not push the test strip back into the test strip opening 2 Check the meter and wipe it clean if needed 4 Close the covers of the meter properly for transportation and storage position1 mendor ivo 0537 Chi Manufacturer Distributor Customer support E mail The arrows should match on the back of the meter Mendor Ltd Munkkiniemen puistotie 25 00330 Helsinki Finland E mail info mendor com Phone 358 45 345 1970 www mendor com cli SpringMed Solutions Ltd UK A Menarini Diagnostics Sweden Mendor Oy Finland 44 800 032 6601 UK 46 40 32 1270 Sweden 358 45 345 1970 Finland info ukK mendor com Uk info menarinidiagnostics se Sweden info mendor com Finland Art PM020517L04_09 Rev 03 15 Before using the product for the first time read the instructions carefully and practice the measurement with the control solution 12 3 2015 14 25 56 PM020517L04_09_ Quick _Guide_EN indd 1 e gt
Download Pdf Manuals
Related Search