Home

Downloads

1. 85 In the warehouse there should be no harmful gas inflammable explosive products and corrosive chemical products and strong mechanical vibration shock and strong magnetic field interference The package box should be at least 10cm above ground and 50cm away from wall thermal source window and air inlet NPC 8207 5 pe Chapter 2 Installation Chapter 2 Installation Product Outline TS NPC 8207 Chapter 2 Installation Evoc Product Appearance and Installation Dimensions Unit mm NPC 8207 La Evoe Chapter 2 Installation External Connectors Drawable Hard Disk Trays HDD Indicator PWR Indicator ele D i yro a E o y E SO Fi REST CONSOLE USB Port Rj45 Port Port Network module mating with different module cards o zo o bal Reserved VGA Mounting Hole BYPASS Switch Power Switch GND Scror DC In 28 NPC 8207 Chapter 2 Installation Overall Assembly Drawing 1 Hanger 2 Chassis 3 Right Rear Hanger 4
2. Conversion Expansion Module 5 Power 6 Left Rear Hanger 7 Cover 8 Front Cover 9 Drawable Hard Disk NPC 8207 Evoe Chapter 2 Installation Installing the Cover Loosen the two captive screws on the backplane of the chassis and then draw the cover backward with force to open it Installing and Removing the Motherboard Installing the motherboard lay the motherboard at the corresponding position in chassis and then fix it by ten M3 pan head combo screws 10 NPC 8207 Chapter 2 Installation Evoe Removing the Motherboard open the cover first remove the patch board module and then loosen the ten M3 screws fixing the motherboard to remove it Installing the Patch Board First fix the patch board with the patch board bracket by six M3 screws insert the module into the corresponding slot on motherboard and then fix it from top and rear of the chassis by three pan head screws and three counter sunk head screws respectively NPC 8207 11 Evoe Chapter 2 Installation Installing the Driver Unlock the hard disk trays with the key enclosed in the accessory package hold the handle of the hard disk tray and put outward then the hard disks can be pulled out of the chassis so as to replace or install the hard disks Installing the Power First fix the power with the power bracket by two counter sunk head 6 32 1 4 screws lay the module at the corresponding position in c
3. to operate A magnetic screwdriver is recommended Magnet helps to prevent screws from remaining in the enclosure Do not leave any tools or accessories inside the enclosure 10 Ensure abundant cooling and ventilation 11 Non professional personnel are not allowed to open the enclosure Contents Chapter 1 Product Introduction 1 OVET Wasa en seri lcse inven an ean dient lated eas 1 Main Functoni tf 2 As th tes oh ho east ON AU os Lodo iQ Oe aS ce 2 Power Feather nae boiler nella ei 3 Main Performance culi aa 3 Mounting Mode sth GLi Lala ha fats alal iaia 4 Requirements of Transportation and Storage i 5 Chapter 2 Installation sser eere r a oa EE IEA illegal 6 Product Outline seai n A de cat cae ETE EE ERE EEE TA Product Appearance and Installation Dimensions External Connectols eara a E E A SE 8 Overall Assembly Drawing 9 Installing the Cover urinaria na nn 10 Installing and Removing the Motherboard 10 Installing the Patch Board 11 Installing the Driver isssie cictvtersacteliverthesteoeedledes tient a e la h 12 Installing the Power iii 12 Tostalling the FAN inainte n Ea E E EE E E EEA 13 Chapter 3 Installing the Drivers 14 Chapter 1 Product Introduction Evoe Chapter 1 Product Introduction Overview NPC 8207 is a medium and high end network platform based on X86 architecture The PC adopts standard
4. 2U 19 rack mount and modular design which facilitates the expansion of network and storage function therefore it is ideally suitable for various network applications It adopts Intel PCH C206 server chipset supports Intel new generation Sandy Bridge and Ivy Bridge processor provides four DDR3 DIMMs up to 16GB two Gigabit electric ports and three front built network module expansion slots based on PCIe The product supports two drawable hard disk trays which supports 3 5 standard hard disk it also supports one CF card and one IDE DOM disk as the data storage device There are two USB ports one COM port RJ45 supports serial port redirection function two Gigabit electric ports and three EVOC ENM series network module slots on the front panel of the chassis One PCI slot and one PCIe x8 slot are expandable on the rear panel by conversion board so as to expand the additional functions It supports various module cards such as two electrics two optics two electrics and two optics four optics four electrics eight optics eight electrics four optics and four electrics etc which can be powered by AC DC and single power supplies The product is ideally suitable for hardware requirements in various network applications such as firewall anti virus wall load balance VPN DNS and AAA etc NPC 8207 1 Evoe Chapter 1 Product Introduction Main Function Microprocessor Supports Intel Socket FCLGA1155 packa
5. NPC 8207 2U C206 FAMI 28 BEEP 2U C206 Medium and High End Network Platform Version C03 Evoc Copyright Notice Information offered in this manual is believed to be correct at the time of printing and is subject to change without prior notice in order to improve reliability design and function and does not represent a commitment on the part of the manufacturer In no event will the manufacturer be liable for direct indirect special incidental or consequential damages arising out of improper installation and or use or inability to use the product or documentation This user manual is protected by copyright No part of this manual may be reproduced stored in any retrieval system or transmitted in any form or by any means mechanical electronic photocopied recorded or otherwise without the prior written permission from the manufacturer Trademarks EVOC is a registered trademark of EVOC Intelligent Technology Co Ltd Other product names mentioned herein are used for identification purposes only and may be trademark and or registered trademarks of their respective companies Please visit our website http www evoc com for more information or send an email to the Technical Support Mailbox support evoc com International or support evoc cn Domestic for consultation Hotline 4008809666 Evoe Safety Instructions 1 Please read this manual carefully before using the product 2 Before inserting removing or
6. ge Sandy Bridge CPUs such as Xeon E3 1275 Xeon E3 1225 13 2120 and I5 2500 Supports Ivy Bridge CPUs such as Xeon E3 1225V2 I5 3550S and I7 3770 Chipset C206 Memory Provides four 240Pin DDR3 memory slots supporting ECC and non ECC un buffered and dual channel function The maximum memory capacity supported by a single memory slot is up to 4GB and the total memory capacity is up to 16 GB Network Function Provides two 10 100 1000Mbps LAN ports LAN1 supports Wake on LAN function Display Function gt Supports CRT display hot swap function gt The supported maximum resolution and refresh rate is 2048x1536 75Hz External IO Front built gt 2x USB port gt 2x LAN port gt 1x COM port RJ45 NPC 8207 Chapter 1 Product Introduction Evoe gt 3x network expansion module connector Rear built gt Power switch gt Bypass switch gt VGA connector reserved Other Feature The structure supports 48V DC 220V single AC power the 300W single AC power is the standard configuration Expansion Bus gt OnePCI slot on board and one PCIe x8 slot expandable at the rear of the chassis by conversion gt Three PCle x8 slots supporting front built network module Power Feature gt Input Voltage Frequency 220VAC 50Hz adapter input gt Power Consumption of PC 65W Standby Power Consumption of PC 140 W 100 operates 3D Main Performance Mechanical Dimensions Weight and Environmen
7. hassis and then fix it from the bottom the rear and the near side of the chassis by six M3 counter sunk head screws and two counter sunk head 6 32 1 4 screws respectively 12 NPC 8207 Chapter 2 Installation Evoe Installing the Fan First fix the two fans with the fan bracket by eight ST4 8 10 screws lay the module at the corresponding position in chassis and then fix the fan bracket from external of the chassis by four M3 counter sunk head screws NPC 8207 13 lc Evoe Chapter 3 Installing the Drivers Chapter 3 Installing the Drivers Regarding the installation of the driver program and the detailed information of the motherboard please refer to the enclosed CD of the PC 14 NPC 8207
8. re configuring motherboards or expansion cards first disconnect the computer and peripherals from their power sources to prevent electric shock to human bodies or damage to the product 3 Before moving the product please unplug the AC cable from the power socket 4 When inserting or removing boards please firstly unplug the AC power cable 5 Before connecting or disconnecting any signal cable make sure all power cables are unplugged in advance 6 After turning off the computer wait at least 30 seconds before turning it back on 7 All the operations such as upgrade remove or installation shall be implemented on the ESD worktable because some exactitude components are sensitive to electrostatic discharge ESD 8 If there s no ESD worktable please take the following measures to prevent damage from electrostatic discharge ESD a Wear a antistatic wrist strap and connect it with the metal part of the corresponding product b Always touch the metal enclosure or frame before touching any components c Keep part of your body in contact with the metal enclosure to discharge the static while handling components d Avoid unnecessary movement e Hold the components especially the boards by the edges f Place the components on a grounded static free operating platform Use a conductive foam pad if available not the component wrapper g Do not let the components slide on the operating platform 9 Usecross head screwdriver
9. t gt Dimensions 550mm L x 440mm W x 88 1mm H gt Net Weight 10 7Kg gt Operating Environment NPC 8207 3 Evoe Chapter 1 Product Introduction Temperature 0 C 45 C Humidity 40 C 30 90 non condensing gt Storage Environment Temperature 10 C 55 C Humidity 40 C 30 90 non condensing EMC Radiation disturbance is compliant with GB9254 2008 class A Conducted susceptibility meets the threshold of GB T 17618 1998 Reliability MTBF gt S0000h MTTRSO 5h Safety Meets the basic requirements of GB4943 Mounting Mode m19 Rack Mount Desktop Embedded Panel oWall Mount OVESA Standard Arm Portable Others 4 NPC 8207 Chapter 1 Product Introduction Evoe Requirements of Transportation and Storage Transportation Well packaged products are suited for transportation by truck ship and plane During transportation products should not be put in open cabin or carriage During transshipping products should not be stored in open air without protection from the atmospheric conditions Products should not be transported together with inflammable explosive and corrosive substances and are not allowed to be exposed to rain snow and liquid substances and mechanical force Storage Products should be stored in package box when it is not used And warehouse temperature should be 0 C 40 C and relative humidity should be 20

Downloads

Contents

Download Pdf Manuals

Related Search

Related Contents