I F D E - Probotics
Contents
1. PROBLEMS CAUSES SOLUTIONS The following is a list of problems that may occur during standard use of the MOWE PROBLEM NO Signal or Sync appears on the display The lawn mower leaves the working area The lawn mower doesn t correctly return to the recharging base The lawn mower behaves abnormally around the flower beds Working area not completely mowed The mower does not work enough with respect to the set time The lawn mower works less that the time set CAUSE Incorrect connection of the perimeter cable to the base Interruption of perimeter cable Excessive ground slope Perimeter cable incorrectly placed Interference caused by metallic objects The transformer cable has been placed incorrectly or the perimeter cable passes near the base The perimeter cable has been incorrectly placed Insufficient working hours Working area too wide Obstructed cutting disc Worn cutting blades Clocks incorrectly set Working schedule set incorrectly Batteries are worn or not correctly recharged 36 If the solutions described do not solve the problem contact the Service Centre REMEDY Verify the connection of the perimeter cable or the plug connection to the base Control that the transformer green light blinks if it doesn t there is an interruption in the perimeter cable Verify the integrity of the perimeter cable Verify the ground slope and2. 6 Press Key and H Key to modify numerical values 7 Press ENTER to save the number of cycles 8 Press ENTER The display shows 9 Press Key and Key to enter the time in minutes needed by the lawn mower to reach the first secondary area If there is no secondary area enter zero 0 29 Secondary area 1 10 Press ENTER to save the time 11 Press ENTER The display shows 12 Press Key and Key to enter the number of working cycles to be performed in the main area after which the lawn mower will start mow ing the second secondary area If there is no second secondary area enter zero 0 13 Press ENTER to save the number of cycles 14 Press ENTER The display shows 15 Press Key and Key to enter the time in minutes needed by the lawn mower to reach the second sec ondary area If there is no Secondary area enter zero 0 16 Press ENTER to save the time User s manual Set Perimeter 1 Press ENTER The display shows 2 Program the type of perimeter installed in the area to be mowed select YES if perimeter cable has been installed select NO if perimeter cable has not been installed Select x2 if there are signal prob lems perimeter cable mounted select x4 if the problem is not re solved with option x2 select x6 if the problem is not re solved with option x4 B important O OO When the mower is turned on it auto matically sets i
3. Pb 2 x with 4 blades 20 m min ee em SO em 3000 m Eege EVOLUTION approximately for each set programming hour 1 1 hours and 30 min approximate 57 x 42 x 26 cm Sra kg Pb 2 x Li aX 1277122 EE 25 2 V B A S76V 35A Taoa aaa YES NO NO NO YES NO YEG YES TO oN Li x 25 2 V 6 A 28 8 V 3 5A min 1 5 mm 150 meters to be buried 600 m approximate YES YES NO NO VES YES YES ES YES YES YES YES YES YES gt 120 W YES YES YES YES YES YES YES YES YES YES Spiked tread wheel improves machine adherence on STEEP slopes Cleated tread wheels improves machine adherence on INTERMEDIATE Recharge for wither storage keeps slopes batteries charged in winter Power transmitter for perimeter cables from 600 m to 1 km User s manual SAFETY INFORMATION GENERAL SAFETY El important OOO Safety information general indications and notes to be considered when using the machine are mentioned below It is understood that this does not exempt the user from reading the entire manual During design and construction the manufacturer has carefully consid ered the possible hazards and per sonal risks that may result from Interaction with the machine In addi tion to observing the specific laws in force the manufacturer has adopted all exemplary construction technique principles The purpose of this infor mation is to advise the users
4. ltimas est n incluidas las enmiendas sucesivas Verklaring van overeenstemming 98 37 EG bijlage Il punt AJ ZUCCHETTI Via dell Olmo 99 A B Terranuova B ni AR ITALIA verklaart dat de machine waarvan de identificatiegegevens hiernaast worden vermeld en die bedoeld is om gras te maaien in huishoudelijke en andere omgevingen voldoet aan de richtlijnen 98 37 EG 78 23 EEG 89 336 EEG In de laatste richtlijnen zijn ook de latere wijzigingen inbegrepen Bernini Fabrizio Amministratore delegato Managing director Administrateur d l gu Gesch ftsf hrer Administrador delegado Afgevaardigd beheerder C141500901 fm C141500901 fm CONTENTS GENERAL INFORMATION TECHNICAL INFORMATION SAFETY INFORMATION INS t ALLATI seose OPERATING INGTHRUCTIONG A MAINTENANCE INFORMATION TROUBLE SHOOTING iriser ANALYTICAL CONTENTS A Adjustment cutting height 24 Adjustment mower balance 24 Areas without perimeter cable or recharging base work 26 Auto programming settings 30 Auto programming settings 30 B Batteries installation 20 Battery installation 20 Battery recharging with winter recharging kit 35 C Checking the cutting disc 32 Clamps and contact plates 32 Cleaning and maintenance of the mower 32 Control cutting disc 32 Cutting disc replacement 33 Cutting height setting 24 D Date and time settings 28 Description of keyboard controls 22 Display description 23 E
5. 25 Wet grass sensor adjustment 25 Winter recharging Kit battery recharging 35 Work area without perimeter cable and automatic return 15 Work area without perimeter cable and manual return 16 Work area preparation 10 Work in areas without perimeter cable or recharging base 26 Work in separate closed areas 26 Work in small areas without perimeter cable and with the presence of an operator 27 Working area settings 10 Working area with perimeter cable 12 Working hours settings 28 Working phase commands 23 Reproduction even partial of this document without written permission by the manufacturer is forbidden The manufacturer assumes a policy of continual improvement and reserves the right to modify this document without prior notice on condition that modifications do not constitute safety risks 2002 Text illustrations and page setting by IDM experts in technical communications Forli Texts may be partially or totally reproduced if the author is cited User s manual GENERAL INFORMATION PURPOSE OF THE MANUAL The constructor has produced this man ual which forms an integral part of the appliance to provide the necessary infor mation for those authorised to interact with it during its working life As well as adopting good practices for use the manuals intended readers must read it thoroughly and apply its in structions to the letter The constructor supplies this information in its
6. js oeeee js oeeees js oeeees Je eeesees SEL js eeeeeees tree Js oe eeesessesesese D Poe HHH HHH HET OSEOS JP oe ee eeesseesesessees SoSH eee eeseeseseses SoSH HHH HEHE HES ESOS Po eSe eee eseeeeseeses SoSH Se SHH HE EEH ESOS Poe eee seeseseseses LRRRRRRESESESESS SIS Poe e See eseeeseseee Poe H Se HHS eeeseeeeee Poe HSH EHH H ETE SESS Poe e See ees eseseseses Pees eeseeseseseses Js ee eeseeseseoes Pees esses sseseses see eesesesseese Jeo eeeeeseses UU ELLE js oeeeesees js eeeeesees LETETTE ELLE lee eeees WELL t OUT e e eeoreore bttoototoee CITE tetetete D EE oe eee ELE ELE ELE ELE EE D D D Peeeereeoee ELLE LL LL ULT LZ ELLE D D D D D ELLE LEE BLL ELLE banssasnsss bansssnsss jp oeeeeees so eeeeees so eeeeses Serres D D D H D H tooo ooo oo ooo eoOS tooo ooo EOE OO OOS Je oeoeoeoooooe eee oo eee eoeeeoooe ee oe oeeoeeeoeeeooeoe Je ooeeeoeoeooeooe Je ooeeoeeooeooe Je ooeeooeroeoos eeoeeoooore eovooe AALE ELLE EREEREER D ELLE ELLE bkessessesssesssesseessess le oeoeeoooooe bessen jt oeoeoooos jt oeoeeooooe ELLE WELL WELL VILLE ELLE H H H H H ELLE D D D D D D D D D D D D D AALE tee SSeS eeeee IF oTH SSH S SHS SESS SOS SALLE EEEE kesssssesssesssess eae es IDM 41500903200 tif oe ELLE LI ELLE H ELLE Ee eooeoooe eooeeoooe LCE O eooeeooos eoee
7. 31 User s manual MAINTENANCE INFORMATION All maintenance works and replacing of components must be performed by per sons with the necessary experience and technical skills Ga UDanger Attention Unplug the mower Use protective gloves when operating on the cutting disc CLEANING AND MAINTENANCE OF THE MOWER To clean the frame use a sponge soaked in a solution of water and detergent Do not use water under pressure to avoid damaging the electrical parts Do not use solvents or gasoline to avoid damaging the painted surfaces Weekly remove grass residue from un RECHARGING BASE CLEANING Periodically control that the recharging base is free of any object leaves ani CHECKING THE CUTTING DISC Check cutting blades weekly Use a brush to eliminate possible incrus tations from the blades CLAMPS AND CONTACT PLATES Check weekly the contact clamps A of the mower and the plates B on the base clean them with a dry cloth If black Signs are evident on the clamps indicat ing bad electrical contact verify the po sition of the clamps on the plates when contact clamps A IDM 41500903906 tif der the body if grass is wet perform this operation more frequently Periodically make sure moving parts blade front and rear wheels are not ob structed or slowed by dirt or other Suit ably intervene if necessary mals etc that may impede the lawn mower entrance If necessary reverse
8. cable recharging base connection p 18 LL important O OOO O Rigorously respect indicated proce dures since an incorrect installation limits the quality of lawn mower opera tions 10 IDM 41500300400 tif Working area settings Prior to installation all obstacles or ir regularities that could obstruct lawn mower movements need to be consid ered and if necessary protected as indi cated in the following paragraphs Before describing installation proce dures some machine function charac teristics that must always be taken into consideration when setting the working area User s manual C141500901 fm C141500901 fm DEEN POSH eee eeseteos When the lawn mower intercepts the perimeter cable signal or col lides with the fence it stops and moves immediately backwards changing direction Ke EE ge ELLE If the garden path is level with the lawn and free of obstacles it is not necessary to delimit it ELLE E D of D D oe oe oe of oe oe oe oe of D D EI If the crossing lane forms a step it must be bordered Do not delimit trees fences or other objects that can tolerate the impact with the frame If obstacles that can support the body s collision are surrounded by flower beds or roots that can ob struct the lawn mower function or damage it they must be bor dered ELE LELCEEELERH ELE H H H H ELLE ELLE ELLE DEL ELLE ELLE D
9. four available pin holes D 4 Perform the same adjust ment on the other battery WET GRASS SENSOR ADJUSTMENT 1 Rotate the cam pin to adjust the distance X between one and the other El important Machine sensitivity increases when the distance between the pins decreases It is advisable not to keep the pins too close to gether In the event of rain the machine stops the cutting blade and returns to the charger base where Is remains in stand by To restart work press the CHARGE button when humidity conditions meet cutting requirements 25 User s manual GENERAL SUGGESTIONS The first time the lawn mower is used grass height must not be over 10 cm If grass is too high run the mower lowering the blade by 1 cm at a time every 1 2 days until the desired height is rea ched With the correct program ming the lawn will be perfect at all times It is advisable to program the mower so as not to make it IDM 41500303700 tif work more than necessary bearing In Make sure that the lawn to mow is mind the seasonal variation in grass free of projecting objects e g small growth so as not to expose it to unne rocks tree roots that could damage cessary wear and reduced battery the blades of the cutting disc working life Work in separate closed areas 1 Retrieve the lawn mower robot from the recharging base mak ing sure the yellow light on the transformer is permanently on b
10. high the lawn mower can work with out a perimeter cable Decide the best position for the recharging base and the trans former see p 16 The cable can be placed at ground level or underground The signal quality and intensity could be compromised laying cables underground as a mat ter of fact with the cable at ground level the lawn mower detects the signal at a distance of 65 75 m while with a cable 20 cm underground this dis tance is reduced to 45 m leaving the cable on the surface or only burying it several centimetres is recommended For fur ther information contact your dealer Install the cable respecting distances in dicated in the figure To allow the lawn mower to correctly en ter the recharging base the input end of the cable must be in straight and per pendicular If the cable is placed at ground level it must not be exceedingly taut and it must be secured with the proper nails supplied To mow the area program the lawn mower selecting no perimeter from the menu see p 30 User s manual Work area without perimeter cable and manual return If the area is bordered by a wall or a fence at least 10 cm high the lawn mower can work without a perimeter cable To mow the area program the lawn mower selecting no perime ter from the menu see p 30 and press the start button once the working time is over the lawn mower stops without searching gt the recharging base T
11. important The distance between the trans former and the garage or perim eter cable should not be less than 3 meters and the cables should never be entangled The best position for the recharg ing base is at the limit of the work ing area on a flat stable surface with good drainage to avoid flood ing The charger base must always be placed in the larger work area and never in a secondary or tight area Be careful of any irrigation systems in the work area which must not spray water inside the charger base or on the machine display Ci x 4 I I I I I I I I I I W R vs AW AI AV AN PNK IDM 41500900201 if IDM 41500903706 tif Settings for a rapid return to the 17 recharging base see p 16 xX Leg IDM 41500904506 tif User s manual Perimeter cable recharging base connection 1 Remove recharging base pro tection 2 Place recharging base in the pre established area e Uanger Attention Remove the power cord to per form connections 3 Insert cable as indicated 4 Connect the two ends of the wire to the clamps of the base see illustration BEEF HHEFEEHEEFESHEEHESHEH EOE OD PERE ESEEH EF ESFE ESE SHES OOH OS DLC ULCLULUUULULE TEE EE EEN z re t et te t 18 ELLE ELLE LZ ELLE ELLE ELLE ELLE ELLE LZ CELL TEEN ELLE LL DEER ELE IDM 41500901 100 tif IDM 41500901200 tif IDM 41500901400 ti
12. in household and other environments complies with directives 98 37 EC 78 23 EEC 89 336 EEC and amendments thereto D claration de conformit 98 37 CE annexe Il paragraphe A ZUCCHETT Centro Sistemi S p A Via dell Qlmo 99 A B Terranuova B ni AR ITALIE d clare que la machine identifiable par les donn es rapport es plus bas servant a tondre les pelouses en milieu domestique et non est conforme aux directives 98 937 CE 78 23 CEE 89 336 CEE Pour ces derni res sont inclus les amendements additionnels Modello serie Model Series Mod le s rie Modell Serie Modelo serie Model serie Konformit tsbest tigung 98 37 CE Beilage II Punkt A Die Firma ZUCCHETTI Centro Sistemi S p A Via dell Olmo 99 A B Terranuova B ni AR ITALIEN erkl rt daf die mit den unten angegebenen Daten gekennzeichnete Maschine die dazu bestimmt ist zum M hen von Rasenfl chen in Wohn und anderer Umgebung eingesetzt zu werden folgenden Richtlinien entspricht 98 37 CE 78 23 CEE 89 336 CEE Letztere schlieBen nachfolgende Ab nderungen mit ein Declaraci n de conformidad 98 37 CE anexo II punto A ZUCCHETTI Centro Sistemi S p A Via delOlmo 99 A B Terranuova B ni AR ITALIA declara que la m quina que se puede identificar por los datos al pie de la p gina y que tiene como uso cortar prados tanto en ambientes dom sticos como no dom sticos es conforme a las directivas 98 37 CE 78 23 CEE 89 336 CEE Para estas
13. oe a A bt ok gt vi MN d a SE DN rapt asi Kn Detnge for a rapid return to the re charging base see p 16 min Z0 cm baam Main area Secondary area IDM 41500902600 tif Example closed separate working area installation In case of closed working areas separated by a fence or other ob stacles that block the lawn mow er passage both areas can be connected as shown in the figure To mow the secondary area the lawn mower must be manually transferred see instructions on p 26 Note if the main area cannot be connect ed with the closed secondary area an ad ditional recharging base can be bought for the secondary area According to certain conditions Tex border walls hedges etc the pe rimeter cable must be installed at an adequate distance illustrations show the installation distances of some typical conditions If the cable is placed near hedges plant growth should be considered beyond the indicated 30 cm or else provide periodical pruning MLE SS Ge ses hate eae Oe eva eae eae dr SC 3 Gs x EE Settings for a rapid return to the re charging base see p 16 max 1 cm Main area Closed secondary area IDM 41500902600 tif oe oe IDM 41500902800 tif User s manual sssssssssssssssss ssssssesssesss ssssssess oe Pees esesesees Pees reseseses were reseseses essssssssssss esssssesssss esssssessesss DUUUTUULUUULULULUUELUE DUU
14. own lan guage Italian but it may be translated into other languages to meet legal and or commercial requirements A little time taken to read this information will al low the prevention of risks to health and safety and the risk of economic losses Keep this manual in a clearly identified safe place throughout the working life of the appliance so that it will always be available when required for consultation The constructor reserves the right to make changes without any obligation to provide any prior notice A number of symbols have been used to highlight particularly important parts of the text or important specifications Their meaning is as defined below A Danger Attention Indicates critically dangerous situa tions that if neglected can result in se rious personal safety and health hazards 4A Warning Caution Indicates that suitable procedures must be adopted to avoid putting peo ple s health and safety at risk or caus ing economic losses H important O O Indicates particularly important tech nical information which must not be overlooked IDENTIFICATION OF MANUFACTURER AND APPLIANCE The dataplate shown here is fitted direct ly to the appliance lt features references and all essential information for operating safety A Manufacturer identification B CE conformity label C Serial model number year of construction D Technical specifications IDM 41500300100 tif User
15. re eee DUU Oe ee max 1 cm COCO O OOOOH EEE EEE EEE EEE EEE E EOE E EEE lt re PPP rrr rr rt se eeeeeeeeenfl 200020002010 eeeeeeseeeeiC te eesecsesein PPP rrr rr rt aa aa aa a a ees O aa asae see en DI seseeeseeeenf eeeceseeesiO eeeeeeoooooeiily EE PEFFER REKT eeeeeeeeees KEE FER eecceceeeeeiO DEITZ e PEFFER PEFFER PEFFER PEFFER PEFFER PEFFER PEFFER PEFFER PEFFER PEFFER PEFFER PEFFER FEEF PEFFER PEFFER PEFFER FEEF PEFFER PEFFER PEFFER PEFFER PEFFER PEFFER PEFFER osseeseens Pe eeoeeeeeene Peeeeeseeeene Peeeeeeeesene eeeeeseeoe Pe eeeeseesene Peeeeeseoeene Peeeeseeeesene DT Peeeeeeeesesene Peeeeeseseene Peeeeseee Peeeeeseeoeene Pe eeeeeeseene DT Peeeeeseeseene Peeeeeseseene eeeeee CET RPPP Peeeesseseene EZEZ Peeeeeseeeene Peeeeeseeeene Peeeeeseeeene LEE EE EEES IDM 41500903100 tif DIER DIER Seesseeeeeeeseeeeseeeee OTTELE EE ET OTTELE a e e ae e s e dgegeeeeeeeeeeeeeeeeeeeeg Poe eRe PERE EEE RECEP EEE EESECECEEEEEESEEE OR DEIER ELLE a ee e e ee COCO oOo OO EOE s et eoeeeoooos DT eeoeeeeorors eeoeerooroos eoeereeroroe eoeeree z ereee Seeeeeee Seeeeeeee Seeeeeeee wF LO600SLVLO bassssss basssssss basssssss basssssss ERETTE baesssss vss vss vss s PEREPERE Js oeeeeee SEILLER js oeeees js oeeees js oeeees js oeeees D D eoeesoesove Seeeeee js oeeee
16. s manual C141500901 fm C141500901 fm SERVICE PROCEDURE Please refer to the Manufacturer s serv ice centres for any need For every technical service request re garding the machine please indicate the data found on the identification plate the approximate hours of use and the type of fault detected TECHNICAL INFORMATION GENERAL MACHINE DESCRIPTION This machine is a robot that auto matically mows the grass in your garden It is small compact silent and easy to transport It can freely move within an en closed area detecting the signal transmitted by the perimeter ca ble located on the ground all around the area to be mowed it can also work without a perime ter cable as long as the working area is enclosed by a fence at least 10 cm high When work autonomy has ex pired see technical specifica tions the robot returns to the base to automatically recharge the batteries When this opera tion is over the machine restarts mowing It follows a random pattern with no fixed plan periodically and ran domly the spiral function particu larly efficient on obstacle free areas IS activated It covers an area of up to 3000 m two or more robots can work simul taneously to cover a wider area According to the various operat ing requirements the robot can be produced in several models whose differences are indicated in the technical specifications It is equipped with a keyboard with a us
17. sharpen or re place the disc recharging of the mower If Corrosion signs are evident on the clamps or on the plates clean them us ing fine abrasive paper contact plates B W IDM 41500901 800 tif User s manual C141500901 fm C141500901 fm CUTTING DISC REPLACEMENT 1 Turn off the lawn mower 2 Overturn the lawn mower on a surface that doesn t dam age the protection 3 Remove grass residues from the disc screw 4 Unscrew disc fastening Screws Ga UDhanger Attention Mount the cutting disc with the tabs facing the body 9 Turn the disc to use the second cut ting side of the blade or sharpen tt or replace it with a new one 6 Tighten the disc fastening screws REPLACING THE BATTERIES Battery range depends on the number of working hours the nuts A mower performs Generally the battery working range is between 600 and 1000 cycles 1 Remove the cutting disc Danger Attention This operation should always be performed since when new bat SC teries are mounted the blade EEN could start working for some seconds creating hazardous sit uations hood B 2 Unscrew both nuts A and re battery guards C move the hood B 3 Unscrew the four fastening screws and remove the bat tery guard IC IDM 41500901600 tif 33 User s manual 4 Take the batteries D out disconnecting the clamps E and replace them E important O O OO Reconnect the
18. to use extreme caution to avoid risks How ever discretion is invaluable Safety is also in the hands of all the operators who interact with the machine Carefully read the instructions pub lished in the supplied manual and found directly on the machine while strictly observing those concerning safety Time dedicated to reading will prevent unfortunate accidents re membering what one was supposed to do when the damage is already done is always too late Pay attention to the meanings of the symbols on the applied stickers their shape and colour are significant to safety ends Keep them legible and ob serve the indicated information Never tamper dodge eliminate or by pass the safety devices installed on the machine Neglect to respect this requirement may cause serious risk to personal safety and health Personnel who are to perform any type of work on the machine during its lifetime must possess specific techni cal skills abilities and have acquired certified experience in the specific field Neglect to observe these re quirements may prove hazardous to personal safety and health When using the machine make sure there are no risks especially for chil dren pets and things Perform lifting and handling observing the information found directly on the packaging on the machine and in the instructions furnished by the manu facturer Only use the machine for the purpos es specified by the manufacturer Use of the m
19. C141500901 fm Congratulazioni per aver acquistato il rasaerba AMBROGIO L aver scelto questo prodotto potr soddisfare le vostre esigenze e aspettative Questo progetto nasce da ZUCCHETTI CENTRO SISTEMI S p A Azienda certificata UNI EN ISO 9001 software house che dal 1982 ha consolidato la propria attivit e la propria presenza sul mercato internazionale Le soluzioni applicative del software abbinate al settore industriale di automazione fanno nascere prodotti nuovi che ottimizzano le procedure di lavoro cos che nato dai laboratori di ricerca AMBROGIO Congratulations for having purchased the AMBROGIO lawn mower This choice will surely meet your needs and expectations This product is the result of research at the ZUCCHETTI CENTRO SISTEMI S p A certified UNI EN ISO 9001 software house that since 1982 has been consolidating its role on the international market Innovative software solutions applied to the industrial automation sector introduce new products that optimise working procedures AMBROGIO was developed on the basis of this research Tous nos compliments pour avoir achet la tondeuse gazon AMBROGIO Vous avez choisi un produit qui r pondra vos besoins et a vos attentes Ce projet nat au ZUCCHETTI CENTRO SISTEMI S p A Entreprise certifi e UNI EN ISO 9001 software house qui depuis 1982 a consolid son activit et sa pr sence sur le march international Les solutions d application du logiciel j
20. Emergency stop 23 G General machine description 5 General safety 8 General suggestions 26 General warnings 9 I Identification of manufacturer and appliance 4 Installation of transformer and recharging base 16 Installation procedure 10 Intelligent spiral settings 30 Intelligent spiral settings 30 K Keyboard control descriptions 22 L Language selection settings 28 Lawn mower balancing adjustment 24 Lawn mower storage 34 MI Machine general description 5 Machine manufacturer s identification and 4 Manual purpose of 4 O Optionals 7 P Packaging and unpackaging 10 Password settings 30 Perimeter cable recharging base connection 18 Perimeter cable work area with 12 Perimeter settings 30 Problems causes solutions 36 Programming procedure 27 Purpose of the manual 4 R Rapid return to garage settings 16 Recharging base cleaning 32 Remote control use 31 Replacement cutting disc 33 Replacing the batteries 33 Resumption for work after storage 34 S Safety signals 9 secondary settings 29 Separate closed areas work 26 service procedure 5 set Date and Time 28 Set Language 28 Set Password 30 set Perimeter 30 set working schedule 28 setting the rapid return to the recharging base 16 Starting 22 stop 23 storage restarting work after 34 T Technical specifications 7 Telecomando uso 31 U Unpacking packaging and 10 W Wet grass sensor adjustment
21. LLUULULUELUEULUELUUE DUU DUU DUU DUU DUU DUU OULUULUULUUELUUULUEE SOSH HEHEHE HEHE CITE POSSE HEHEHE HEHE HOOD CITE Cece eee eee eee ES SoSH HEHEHE DEHOS CU D LU CU CU CU DUU CU CU DEU CU CU CU DUU CU CU POH HTH HOOD CLLK GELELLLLEE ELE zeeeeeree D D D D D D D D Seeeseesese D e D D D D D H D t DEE aeet eeet eeg TEE Poe eeeeeroeooooe PTET eee ee eee eee ee ee ed Pee eee ee eee eee ee z ss eeeeeeeeeeeee Be e e aert eert eeert ert erttee reet aer ert ertert er ergg LEES CHOOSE EEE EEE E EEE OOOO OO OOOE SOOO E EEE E EEE EEE EEEOEEEO OOOO OOS COOH EE OE EEOOEOOOS SESS H HSH SHE HEHEHE HEHEHE EEE HEEEEOEOOEOOOD SOSH SEES HHE HEHEHE EHEHEEEHEEOEOHEOOOO OOOSD SHS EH HEHEHE HEHEHE HEHEHEEHEHOEHEHEOESOOO OOSD oe oe oe oe oe POCO E EEE EEE EEE EEEE EEE EEEEO OOOO OOOS ELLE ELE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE ELLE GELLI GELLLLULLLLELEEE GELLI GELLI GELUET GELLI ELLE GELLI Foe E HEHEHE EEOD Foo ESSE HEHEHE OEOS POCO OOH EEE EEE E EEE EEE EEEEE EEE EEE EEOOOOOOE SOOO EEE EEE E EEE HEE EE EEEEEEEEEO OSES OOOS POCO EEE EEE E EEE EEE EEEEEEEE OEE OOOO OOOOS SOPHO E EE EEE HEHEHE EEE EEE EEE EOE EO OOOO OOOS s et imi ime its level eeeeeseessees eeeeeseessees eeeesseessees eeeesseessees eeeeeeeedeez eseaees
22. achine for other purposes may be hazardous to personal safety and health and provoke economic loss All maintenance procedures that re quire precise technical competency or specific skills must be exclusively performed by qualified personnel with acquired certified experience in the specific field Replace deteriorated parts with origi nals to ensure functionality and the foreseen safety level Do not litter the environment with pol lutant material perform disposal ac cording to the pertinent laws in force Do not place hands or feet under the machine when running especially in the wheel area User s manual C141500901 fm C141500901 fm GENERAL WARNINGS The lawn mower may be used only by those who know how to operate it af ter reading and understanding the in structions in this manual Before using the lawn mower make sure that no objects are on the lawn toys tree branches items of cloth ing etc Keep the lawn mower in perfect oper ating conditions by performing the maintenance procedures outlined by the manufacturer Good maintenance guarantees better performance and longer service life Before maintenance and setting pro cedures are performed also by the user if possessing the necessary SAFETY SIGNALS LL Safety signal indicates that the user should carefully read the manual before operating the lawn mower technical skills disconnect the pow er supply The user must in any cas
23. atteries in maintenance 2 Press OFF and put the robot in the area without perimeter cable or recharging base 3 Press ON with password if any and ENTER afterwards press Key and Key the message external will be shown on the display for some seconds and the lawn mower will start working 4 When batteries charge is finished the lawn mower will travel along the perim eter noticing the absence of the re charging base and it will turn off k automatically once it s turned off and on this function will no longer be set 9 Bring the mower near the recharg ing base press CHARGE to bring the lawn mower back to the base and re charge the battery in advance Work in areas without perimeter cable or recharging base 1 Retrieve the lawn mower robot from 3 Access the menu and select NO at the recharging base making sure the the perimeter item p 30 yellow light on the transformer is per 4 Press ENTER exit the programming manently on batteries in maintenance function pressing PAUSE and the 2 Press OFF and put the robot in the lawn mower will start the automatic area to be mowed working cycle continuing until the working time has expired 26 User s manual C141500901 fm C141500901 fm Work in small areas without perimeter cable and with the presence of an operator 1 Retrieve the lawn mower robot from the recharging base mak ing sure the yellow light on the transformer is permanently on ba
24. base and it 24 must be recharged pressing the 4 Place the lawn mower within the pe PAUSE key for at least 12 hours this rimeter allows batteries to be perfectly Peer ON to cu iton charged and efficient ready for use Die a E User s manual C141500901 fm C141500901 fm 7 Press PAUSE to start the automatic An blinking light placed on the front of working cycle lawn mower automatically turns on dur Ing night work to point out its working po LL US If batteries are sufficiently charged the lawn mower starts the working cycle if they need to be recharged the lawn mower is positioned in recharging STOP To stop the lawn mower press the PAUSE key then the STOP key yo UDanger Attention It is possible to stop the lawn mower by lifting it and a sensor halts all functions However this procedure should be avoided EMERGENCY STOP To stop the lawn mower in the event of emergency press STOP Display description While the lawn mow er works the display shows the following data Sx left wheel motor speed La blade motor speed Dx right wheel motor speed Battery battery voltage While the lawn mower is recharging the display shows recharging If the lawn mower off work the display shows work start day and time Working phase commands During the working phase the following When the lawn mower is recharging functions can be performed by the lawn press the same button to make i
25. chaf van uw AMBROGIO Wij zijn er zeker van dat deze machine voldoet aan al uw verwachtingen en vereisten AMBROGIO is een project van ZUCCHETTI met UNI EN ISO 9001 certificaties een softwarebedrijf dat sinds 1982 met haar activiteiten een eigen plaats verwierf op de internationale markt De combinatie van de oplossingen die worden geboden door softwaretoepassingen en de industri le automatisering resulteert in nieuwe producten om de bedrijfsprocessen te optimaliseren Zo ontstond in onze onderzoekscentra AMBROGIO Manuale d uso Italiano Rasaerba Robot User s manual English Lawn M ower Robot Manuel d utilisation Fran ais Tondeuse gazon Robot Bedienungshandbuch Deutsch Rasenmahroboter Manual de uso Espa ol Cortadora de c sped Robot Gebruiksaanwijzingen Nederlands Grasmaaimachine LU Ka SS Dichiarazione di conformit 98 37 CE allegato II punto Al ZUCCHETTI Centro Sistemi S p A Via delOlmo 99 A B Terranuova B ni AR ITALIA dichiara che la macchina identificabile dai dati riportati in calce da utilizzare per rasare prati in ambienti domestici e non conforme alle direttive 98 37 CE 78 23 CEE 89 336 CEE Per queste ultime sono compresi i successivi emendamenti Declaration of conformity 98 37 CE annex Il paragraph Al ZUCCHETTI Centro Sistemi S p A Via dell Qlmo 99 A B Terranuova B ni AR ITALY declares that the machine identified by the data included hereafter to be used for lawn mowing
26. clamps according to the polarity of the new batteries a wrong con nection may damage the electronic parts of the mower see pag 20 Lead battery batteries D gt Es LAWN MOWER STORAGE If the mower is not used for a long period of time it is advisable to keep it in a safe dry place Before storage recharge the mower for at least 12 hours 1 carefully clean the lawn mower 2 place the lawn mower in the recharg ing base 3 the display shows recharging and the battery tension value 4 press PAUSE Used batteries must be given to an au thorized collection centre Lithium battery clamps E 5 when recharge is done at least 12 hours turn the lawn mower off and place it in a dry place at an environ mental temperature of 10 30 C 6 control batteries charge status once a month and recharge them if nec essary Or use the suitable recharge kit for winter garaging Contact your dealer The transformer must be unplugged from the power supply RESUMPTION FOR WORK AFTER STORAGE Plug the recharging base to the power Supply and make sure the plates are clean 1 bring the mower near the recharging base 2 press the ON key and then the CHARGE key CR The mower searches for the perimeter cable and follows it to the base where it will recharge If the batteries need recharging the mower positions shows recharging if the batteries are sufficiently charged the mower starts the work cycle as p
27. ctronic card with microprocessor for bs function control Handle to liftand movethe e ET e ene ene soe e upporting frame supports all main lawn mower Eege eee ee eee EE components of the lawn mower Wet grass sensor detects rain and returns the machine to the or garage EEN DI CU Nails pocket to fix the perimeter SS cable and the recharging base to j 8 the ground A a Si e ee ee Aer ir e e ere Ee Je lge Zi d A E ee ee ee ei EN ee ien e et e de underground to delimit the working area IDM 41500900101 tif 1 The illustration is only an example since the contacts may be either on the front or top sbe User s manual C141500901 fm C141500901 fm TECHNICAL SPECIFICATIONS Cutting disc Cutting speed Cutting height Cutting width Maximum coverage Average coverage Working range Size Total weight without batteries Battery Recharging base Transformer Perimeter cable Maximum perimeter cable length Sinusoidal perimeter system patented Auto programming patented Intelligent spiral Remote control Wet grass sensor Recharge for wither storage Cutting Disc Safety Blade Consumption Patent compliant US 3550 714 OPTIONALS Lithium battery improves machine performance on slanted gardens It is especially recommended for its light weight and durability Remote control to use the machine in manual mode PROFESSIONAL DELUXE PE DELUXE LT
28. e 7 User s manual
29. e e e D e e D Foe eeeeeees ELLE FOeeeeeeeee ELLE zrtettrersss ELLE DEL e e e e Hee eeeeees SS TAE EE ee H d de ELLE zesessseesessseeseeeseeseeesee E CELL IDM 41500902000 tif emm MAAAAAA AAAAAAAAAAAA oe IDM 41500902100 tif IDM 41500902200 tif a a o WS h di be 3 EE We E D D D D D D e EE Se Deg A NV VV url VV VV D d AV 4 AV ASE AST A iY IDM 41500902300 tif User s manual Working area with perimeter cable Before installing the cable decide the best location for the recharg ing base and the transformer see p 16 The cable can be placed at ground level or underground The signal quality and intensity could be com promised if cables are under ground as a matter of fact with the cable at ground level the lawn mower detects the signal at a dis tance of 65 75 m while with a ca ble 20 m underground this distance is reduced to 45 m leaving the cable on the surface or only burying it several centimetres is recommended For further information contact your dealer Start placing the cable from the point es tablished for the recharging base and continue along the perimeter of the area following the ground irregularity To allow the lawn mower to correctly enter the recharging base the input end of the ca The illustration provides a typical insta
30. e operate in full safety conditions espe cially when working on the lower part of the lawn mower following the pro cedures as illustrated by the manu facturer All interventions on the recharging base must be performed after discon necting the power supply Use personal protections as recom mended by the manufacturer espe clally the protective gloves when handling blades and cutting discs Always remove the blade before re placing the batteries Prohibiting signal indicates that the lawn mower should not be used in the presence of children and or pets Danger signal indicates that the user should not ap proach to the blades while the lawn mower is operating User s manual INSTALLATION PACKAGING AND UNPACKAGING The machine is delivered suitably packaged When unpacking re move carefully and check compo nent integrity All the necessary information for handling is found on the packag ing E important Keep the packaging for future usage INSTALLATION PROCEDURE Installation procedures depend on the working area to be covered for this rea son the chapter is divided into the follow ing paragraphs 1 working area settings p 10 working area with perimeter cable p 12 Work area without perimeter ca ble and automatic return p 15 Work area without perimeter ca ble and manual return p 16 2 transformer and recharging base in stallation p 16 3 perimeter
31. e lawn mower PAUSE press to stop the lawn mower the display is in stand by it is now Key when working press to restart the previously i possible to program the lawn mower stopped blade When programming press to increase When pressed again the lawn mower the items indicated by the menu i resumes working If the key is pressed i i during battery recharging the lawn mower does not resume working until Display shows all functions i the key is pressed again and Pause disappears from the display CHARGE press to bring the lawn mow decrease items indicated by the menu l battery in advance If the key is pressed while the lawn mower is recharging re i l charging is interrupted and the lawn ENTER when working press to start the i mower resumes working spiral function When programming press to confirm and save the selection performed OFF STOP press to stop the lawn IDM 41500300400 tif STARTING Before starting the lawn mower control 6 Enter the saved password only if it s that the garden is free of obstacles that not 0000 and press ENTER could damage functional units stones To set the antitheft password see pro toys etc gramming procedures p 30 1 Regulate the cutting height pag 24 2 Make sure the cutting disc is in LISS stalled correctly p 32 The first start of the lawn mower must 3 Regulate the lawn mower balance p be done on the recharging
32. eooes EREEREER z ee eea eooeoooe eeooerooee eooeeooee eoeeeoooe tetetete tetttes tettes t FST SSSHSSH SSS SS SOS FST H SHH SESS SEOSS FSS SSS SSE HS OOS ToT S SHOTS SEES FoF STS Teeee FST SSS STEee Fee r reese Fee r reese FSS SSH S SHS SSS SE EHS terres SS SSSHHS SHS SH HE OEE toe SHS Sees toe SHS SHH EEEE PS SSH ESHEETS ESSE ESE EES HHH E SESE EEE EEE EEE EEEEEEEOEEOOOOOSOOOOS the bor etc t least wall to User s manual 14 imits om ies Im the per or to bor ier a t the lawn lev d up to the fence position IniImumM tance between the th a barr igh e g prevent the lawn mower from go beyond the perimeter cable IS duce the d cables to am ble to increase Isa roads water bod INQ IS require IC areas are a istance to 40 cm dv th the lawn ter cable at a distance of 5 cm isa WI of the area with paving Example of flower bed Minimum passage area If mow If publ el e g derd der areas w 15 cm h ing C141500901 fm To avoid interference to the cable signal keep it away from metallic objects metallic drains or normal drains with electrical connections inside Use specific clamps to add junctions if necessary Doan Do not use insulating tape IDM 41500903306 tif Work area without perimeter cable and automatic return If the area is bordered by a wall or a fence at least 10 cm
33. er friendly and easy to program dis play It can operate day and night only working time start and finish including work days for intended use need to be IDM 41500300200 tif set If the lawn mower is lifted or overturned the blade stops to prevent hazards to people and or pets User s manual It is fully water resistant and can there The grass in your garden will always be fore operate in all weather conditions at the desired height to guarantee an i even lawn all year round It is not water proof therefore it must not be submerged under water Trasformer with cable supplies the recharging base Transmitter transmits e the signal to the charger o base Winter recharge Kit optional to Remote control optional recharge or keep batteries permits the machine to be used charged without using the garage in manual mode Recharging base where the lawn mower is placed when it needs to be recharged 1 Protection cover allows reaching Internal Components Batteries guarantee a specific working range see tecnnical data 1 Contact devices provide connection to the base for i recharging DC E LOR CRE Cutting disc with 4 blade reversible g O gt M e O zO W V Pivoting front wheels i oe Pi i Driving wheels they drive the lawn mower powered by er eeh ee ig et eng l ctricai motors and set up e e e e Ele
34. f User s manual C141500901 fm C141500901 fm 0 Fasten the recharging base to the surface with nails A if necessary use expansion dowels B 6 Fasten the protection cover with the screws 7 Connect the base to the transformer by plugging in the connectors 8 Insert the power supply cable plug C in the wall socket Now the lawn mower is ready to be programmed at desired times and modes 19 IDM 41500901306 tif IDM 41500901100 tif H ALW c 00301 tif User s manual Battery installaion 1 Unscrew the charge knobs IA and remove the top hood B D 2 Unscrew the four fastening screws and remove the bat tery guards C 3 Insert the batteries D and connect the terminals E as illustrated M Brown N Black A Blue R Red 4 For lithium batteries connect the terminals E as illustrated N Black R Red 4A Warning Caution Lithium batteries must have a specific feeder knobs A hood B IDM 41500904300 tif IDM 41500901606 tif User s manual C141500901 fm C141500901 fm 9 Unscrew the battery base fas tening nut F and place the pin in one of the four available pin holes G 6 Assemble the battery guards C 7 Assemble the top hood B and screw in the charge knobs A 21 IDM 41500901600 tif IDM 41500904700 tif User s manual OPERATING INSTRUCTIONS DESCRIPTION OF KEYBOARD CONTROLS ON press to turn on th
35. if necessary border the area Verify the cable placing Correctly place the perimeter cable stretch the transformer cable or move the perimeter cable away from the recharging base Invert the rotating direction around the flower bed Counter clockwise Extend the working hours Limit working area or extend working hours Control that the cutting disk rotates freely Replace cutting disk set the lawn mower clock correctly set working schedule correctly Replace batteries write the number of cycles and total working hours in the manual Recharge batteries for at least 12 hours leaving the machine set to PAUSE on the recharging base User s manual C141500901 fm C141500901 fm The lawn mower doesn t perform the rapid return or doesn t reach the recharging base Out of perimeter when Particular cable collision returning to the charger conditions l e collision in a Manually restart the lawn mower base corner etc Control the exact settings for the Rapid return incorrectly set rapid return The Robot when recharging Shows Pause Rain ne Robot recharges and is still Manually press the CHARGE key because of rain to restart the lawn mower The still Robot shows Blackout Absence of power while the robot Manually restart the lawn mower tries to find the docking station The gn een Absence of power while the robot Manually restart the lawn mower works near the border wir
36. ified 9 Press Key and UI Key to modify numerical values 10 Press ENTER to confirm modified values 11 Press ENTER The display shows 12 Program the working schedule for the second part of the day Example from 7 00 to 10 00 p m 13 Press ENTER to move the cursor to values to be modified 14 Press Key and Key to modify numerical values 15 Press ENTER to confirm modified values Hl important O O To enhance battery life and permit work cycles at programmed intervals work hours can be set for a maximum of 20 hours a day User s manual C141500901 fm C141500901 fm Secondary settings To perform this function the time needed for the lawn mower to reach the secondary area follow ing the perimeter cable must be programmed Follow indications below to calcu late the time 1 Place the lawn mower out of the recharging base directed towards the output cable 2 Press ON and CHARGE 3 Record the time the lawn mower needs to reach the middle of the secondary area Bimportant OO If there is a setting for the rapid return on the way to the secondary area the lawn mower must be manually directed to the perimeter cable when it exits 4 Press ENTER The display shows 5 Press Key and Key to enter the number of working cycles to be per formed in the main area after which the lawn mower will start mowing the first secondary area If there is no secondary area enter zero 0
37. llation example LL important Respect the rotation direction around flower beds counter clockwise E Du VE yay GH Ka aS ae Si SEH y GA eps ee nee Ze Ge Example separate working area installation It is at times advisable to divide the work ing area into separate areas as in the following cases when lawns are not connected 12 DM 41500902400 ble must be straight and perpendicular for at least 2 meters and the output end of the cable must end at least 30 cm away from the recharging base B important O OO O If the cable is placed at ground level it must not be exceedingly taut and it must be secured with the proper nails supplied Settings for a rapid return to the recharging base see p 16 y L IDM 41500902500 tif when one area is considerably larger than the other and the two areas are connected by a passage that is too narrow User s manual C141500901 fm C141500901 fm In these cases the recharging base must be positioned in the larger area connecting the perim eter cable to the secondary area with a passage bearing in mind that the distance between the two cables must not be below 70 cm It will be like a Separate working area to mow the secondary ar ea the lawn mower must be pro grammed accordingly see Managing secondary areas Se 9 E Sc a s t amp a hey Ei S SE Z S E S Gar
38. n Perimeter Yes mode Options NO x2 x4 x6 are deactivat ed when the mower is turned off Use them with extreme caution only in the event there are no pools or slanted ar eas 3 Press Key and Key to modify 4 Press ENTER to save the program Intelligent spiral applicable models only 1 Press ENTER The display shows settings for When Intelligent spiral is selected the machine only performs spiral movement when un cut grass is found concentrating on that area 2 Press the button to select random spiral mode in this way the machine randomly mows in spiral movement 3 Press ENTER to save the program Auto programming settings applicable models only 1 Press ENTER The display shows for 2 Press and to disable this option or set the percent of mowed lawn grass to be used for auto programming function start The auto programming function reduces machine work time based on grass conditions When the lawn surface is cut in a percent higher than the one set in the Autoprogramm Menu item the machine automatically set an_ idle interval that delays the next exits from the charger base the higher the percentage of mowed lawn the longer the machine idle interval 3 Press ENTER to save the program Set Password 1 Press ENTER The display shows The lawn mower can be protected by a pass word made of four digits that the user may personalize following the in
39. o recharge batteries manually move the lawn mower to the main area IDM 41500903500 if Setting the rapid return to the recharging base some settings can be done along the perimeter cable that allow the lawn mower to change direc tions reducing the distance cov ered and the time to return to the charging base To do so an equilateral triangle of 40 cm should be formed with the perimeter cable The illustration shows some useful indications to determine the right location of the setting for the rapid return to the charging base Note when the lawn mower follows the perimeter to reach a secondary area it does not consider the settings for a rapid IDM 41500903601 tif return rectly placed the lawn mower may not be A able to return to the recharging base If the setting for a rapid return is incor Installation of transformer and recharging base The transformer must be kept out of Installation must be carried out correctly direct sunlight protected from the and according to current legislation elements and in a well ventilated but not To connect the transformer to the pow air tight position connected to the er supply line a standard electric plug is power supply line Keep out of reach of needed children 16 User s manual C141500901 fm C141500901 fm Danger Attention The transformer connection to the recharging base must be performed with the power sup ply disconnected Pl
40. ro grammed User s manual C141500901 fm C141500901 fm If the batteries are depleted to a point where they are under the safety voltage an automobile battery charger 12V 3 Ah must only be used to recharge lead batteries The lithium battery can only be recharged with the supplied battery charger BATTERY RECHARGING WITH WINTER RECHARGING KIT 1 First connect wire connector A and then wire connector B 2 Press the ON key and wait un til the display shows Danger Attention This operation must be performed with the perimeter cable connector unplugged 3 Connect the black connector C with negative polarity and the red connector D with positive polarity to the corresponding knobs Note If the operation is not performed within 30 seconds from the operations described in point 2 the machine auto matically turns off Restart from point 2 and repeat the procedure 4 The writing on the display Ensures correct connector connections The power led should turn red or remain yellow Periodically check the machine during re charging If the power supply is interrupt ed for a long period of time the machine automatically turns off and the ON key must be pressed again Py es cable A IDM 41500900801 tif IDM 415009001 000 tif 9 To disconnect the machine from the winter recharge press OFF and dis connect connectors C and D User s manual TROUBLE SHOOTING
41. sonalized password to be defined that in case of theft will prevent the lawn mower from being used To access the menu press the keys se After entering the desired value press ENTER and press PAUSE El important OOO If STOP is pressed instead of PAUSE all values set will be cancelled User s manual Set Language The display shows 1 Press Key and Key to scroll available languages 2 Press ENTER to confirm modified values Set Date and Time 1 Press ENTER The display shows IA E DD M Vl 7 YY MAR 19 09 00 2 Press ENTER to place the cursor on day month year 3 Press Key and Hl Key to modify numerical values 4 Press ENTER to confirm modified values 9 Press ENTER The display shows 6 Press ENTER to place the cursor on HOUR and MINUTES 7 Press Key and Key to modify numerical values 8 Press ENTER to confirm modified values Set working schedule 1 Press ENTER The display shows 2 Program every single day of the week entering the number 1 to turn it on or O to keep it stand by _ 28 3 Press ENTER to move the cursor to values to be modified 4 Press Key and Key to modify numerical values 5 Press ENTER to confirm modified values 6 Press ENTER The display shows 7 Program the working schedule for the first part of the day Example from 07 00 to 09 00 am 8 Press ENTER to move the cursor to values to be mod
42. struc tions below The password set by default is OOOO it s advisable to enter four numbers that can be easily remembered ex birth date 2 Press Key and Key to enter YES 3 Press ENTER to save the program The display shows User s manual C141500901 fm C141500901 fm 4 Enter the old password selecting eve 7 Enter the new password using EN ry single digit with ENTER and modi TER Key and Key fying values with Key and Key 8 Press ENTER to save the program 5 Press ENTER to save the program The display shows 6 Press ENTER The display shows 9 Enter new password again 10 Press ENTER to permanently save REMOTE CONTROL USE Bl important The remote control works with infrared rays Keep it directed towards the receiver no further than 6 m away A RIGHT ARROW hold down to move the machine to the right B LEFT ARROW hold down to move the machine to the left C PAUSE START press to turn the machine on or if already Cae a rena on to pause D FUNCTIONS KEY hold down this key to perform the following operations 2 Make the machine perform spiral movement only if on and moving 3 Send the machine to recharge only if 1 Make the machine leave the recharg on and in pause ing base and start the work cycle 4 Move the machine away from the pe provided that it has been pro rimeter cable if it follows the cable grammed and does not function correctly
43. t leave mower using the Indicated buttons the recharging base and restart work press PAUSE to stop the lawn mow ing er press it again to restart it Press the Key to stop the blade press CHARGE to send the lawn press the Key to start the blade mower to the recharging base to re press ENTER to start the spiral charge batteries working program a a 29 User s manual CUTTING HEIGHT SETTING Cutting height can vary from 2 to 7 cm according to the desired height of the grass yo UDanger Attention Before performing this setting turn the mower off by pressing OFF STOP 1 Remove the cutting blade 2 Unscrew the locking screw 3 Manually lift or lower the cut ting unit until desired height is reached as indicated on the graduated plate 4 WVhen adjustment is conclud ed tighten fastening screws and reassemble the blade LAWN MOWER BALANCING ADJUSTMENT The lawn mower is supplied with balance adjusted for flat grounds In case of sloped grounds the lawn mower balance can be mod ified by moving both batteries for wards or backwards 1 Unscrew both nuts A and re move the top hood nuts A 24 IDM 41500904306 tif User s manual C141500901 fm C141500901 fm 2 Unscrew the four fastening screws and remove the bat battery guards B tery guards B d IDM 41500901600 tif 3 Unscrew the battery base fas tening nut C and place the pin in one of the
44. tteries in maintenance 2 Press OFF and put the robot in the area to be mowed 3 Access the menu and select NO at the perimeter item p 30 4 Press ENTER and the lawn mower will start the working cycle yo UDanger Attention This operation must be per formed under operator control who PROGRAMMING PROCEDURES Lawn mower use can be easily personal ized following the procedures shown be low The CASCADE menu allows language selection date and time setting lawn mower work programming and second ary area management The menu consists of the following op tions SET LANGUAGE Ip 28 SET DATE AND TIME p 28 SET WORKING SCHEDULE Ip 28 This setting allows working hours to be set during the day and working days during the week SET SECONDARY AREAS Ip 29 This option allows automatic mowing management of one or two second ary areas in the garden SET PERIMETER p 30 This option allows to set the machine functionning by perimeter cable or by collision 27a MAANANTAINA IDM 41500904100 tif must create an obstacle every time the lawn mower should change direction Do not use feet to create an obstacle INTELLIGENT SPIRAL SETTINGS p 30 This option is required to set spiral machine operations AUTO PROGRAMMING SETTINGS Ip 20 This option is required to set machine Operations to reduce work time SET PASSWORD Ip 30 This option allows a per
45. umel es au secteur industriel d automation ont permis la naissance de nouveaux produits qui optimisent les proc dures de travail C est ainsi que dans nos laboratoires de recherche est n AMBROGIO Wir gratulieren zum Kauf des Rasenm hers AMBROGIO Ihre Bed rfnisse und Erwartungen werden durch die Wahl dieses Produkts mit Sicherheit erf llt Die Firma ZUCCHETTI CENTRO SISTEMI S p A mit UNI EN ISO 9001 ausgezeichneter Betrieb Software House die ihre Produktion seit 1982 festigt und damit auf dem internationalen Markt vertreten ist zeichnet f r dieses Produkt verantwortlich Die angewandten Softwarel sungen f hren in Kombination mit der industriellen Automatisierung zur Entstehung neuer Produkte f r eine Optimierung von Arbeitsprozessen Auf diese Weise entstand in den Forschungslabors AMBROGIO Felicidades por haber adquirido la cortadora de c sped AMBROGIO Podr satisfacer sus exigencias y expectativas al haber elegido este producto Este producto nace de ZUCCHETTI CENTRO SISTEMI S p A Empresa certificada UNI EN ISO 9001 software house que desde 1982 ha consolidado su propia actividad y su propia presencia en el mercado internacional Las soluciones de aplicaci n del software combinadas con el sector industrial de automatizaci n hacen nacer nuevos productos que optimizan los procedimientos de trabajo Es as que ha nacido en los laboratorios de investigaci n AMBROGIO Wij wensen u van harte geluk met de aans
Download Pdf Manuals
Related Search