Model No. K-EF134L02E K-EF134L03E K-EF134L06E - Psn
Contents
1. HD IR Weatherproof Network Dome Camera User s Manual Model No K EF1 34L02E K EF134L03E K EF134L06E Version 1 0 2 Welcome Thank you for purchasing our Network camera This user s manual is designed to be a reference tool for your system Please read the following safeguard and warnings carefully before you use this series product Please keep this user s manual well for future reference Important Safeguards and Warnings 1 Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated DC12V in the IEC60950 1 Refer to general introduction Please note Do not connect two power supplying sources to the device at the same time it may result in device damage We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modification or attempted repair 2 Transportation security Heavy stress violent vibration or water splash are not allowed during transportation storage and installation 3 Installation Do not apply power to the camera before completing installation Please install the proper power cut off device during the installation connection Always follow the instruction guide the manufacturer recommended 4 Qualified engi2. enclosure Improper enclosure clean method such as use cloth may result in poor IR effect of camera with IR function 7 Accessories Be sure to use all the accessories recommended by manufacturer Before installation please open the package and check all the components are included Contact your local retailer ASAP if something is broken in your package Accessory Name Amount Network Camera Unit 1 Quick Start Guide 1 Installation template label 1 CD 1 Important Safety Instructions 1 111 Table of Contents General lntrod ction n raon E a O E LSO E 1 1 1 OVENVIEW anana a a a ccna aessuasanaionrseceasatense uma nactaiate 1 1 2 A a a E a A A e a E aS 1 1 3 APEC O 2 A O ee dal natal tesa acer e AGRO oO Da ai esi het tat etch A Me cet AS ek 4 2 1 CAN ld a o 4 2 2 Framework and Dimensi n its 5 Device Installato M e a ie eee Pi R E E a R a a a E 6 3 1 Installation Steps for Plastic DOM ooooooconoccnocicocooncoocconccononononcnnononnnconcn nono nonncnnnnn 6 3 2 Restore Factory Default Setup Introducti0N oooncocnnninoncnncoconnconcnncnncnncnncons 8 Quick Configuration TO a o iabtates daceseoueates as 9 4 1 OVOGNVICW at Gaadimieniam Gate natn Eun tested agetoionss 9 42s OPE MM A a eT TES 9 WeED OPEraION kl het el E 11 5 1 Network Goin iii 11 5 2 Login and Main Interface uni 11 FAQ ae e E Pie ee aS E No EAEE TAE E E e E Se aa 13 1 General Introduction 1 1 Overview This series networ
3. k camera integrates the traditional camera and network video technology It adopts video data collection transmission together It can connect to the network directly without any auxiliary device This series network camera uses standard H 264 video compression technology which maximally guarantees the video quality It supports the IR night vision function In the night environments the device can use the IR light to highlight the object which is suitable for the surveillance function in the low illumination environments The weatherproof design conforms to the IP 66 level It has the sound weatherproof function suitable for use in the outdoor environments It can be used alone or used in a network area When it is used lonely you can connect it to the network and then use a network client end Due to its multiple functions and various uses this series network camera is widely used in many environments such office bank road monitor and etc 1 2 Features User e Different user rights for each group one user belongs to one group Management The user right shall not exceed the group right e Support central server backup function in accordance with your configuration Storage and setup in alarm or schedule setting l l Flu etion e Support record via Web and the recorded file are storage in the client end e Support network storage function such as FTP Data e Data transmission via PoE Transmission e Network camera suppor
4. neers needed All the examination and repair work should be done by the qualified service engineers We are not liable for any problems caused by unauthorized modifications or attempted repair 5 Environment This series network camera should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc Please keep it away from the electromagnetic radiation object and environment Please make sure the CCD MOS component is out of the radiation of the laser beam device Otherwise it may result in CCD MOS optical component damage Please keep the sound ventilation Thunder proof device is recommended to be adopted to better prevent thunder 6 Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work Do not touch the CCD MOS optic component You can use the blower to clean the dust on the lens surface 11 Always use the dry soft cloth to clean the device If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device Please put the dustproof cap to protect the CCD MOS component when you do not use the camera Dome enclosure is the optical component do not touch the enclosure when you are installing the device or clean the enclosure when you are doing maintenance work Please use professional optical clean method to clean the
5. nes sensitivity level ranges from 0 to 100 area threshold ranges from 0 to 100 Activation event video storage image snapshot log email function and etc Record Priority Manual gt Video detect gt Schedule Storage Management Network storage Wire Network 1 channel wire Ethernet port 10 100 Base T Ethernet IPv4 IPv6 HTTP HTTPS SSL TCP IP UDP UPnP ICMP IGMP Network Protocol SNMP RTSP RTP SMTP NTP Required to synchronize to recorder DHCP DNS PPPOE DDNS FTP IP Filter QoS Bonjour Remote Monitor system setup file download log information maintenance Operation upgrade and etc Restore Default Setup IR light IR light 20M DC12V power and PoE Warning Do not connect these two power supplying sources to the deviceat the same time it may result in device damage Power DC12V 330mA Consumption PoE DC48V 90mA Working oR LAN Temperature eee Working 6 Humidify aso Dimensions mm 113 x86 Weight 290g Excluding box Installation Ceiling and wall mount Reset button JO OWILIe e 19u9r Note Panasonic Security Viewer is not supported EMS E Series Management Software amp Mobile EMS do not support i PRO series NVR Only SXVGA recording is available with i PRO series NVR See support web page below for further details http security panasonic com 2 Structure 2 1 Components You can refer to the following figure for multiple function combinati
6. on cable information See Figure 2 1 Component Name Device lens Dome body Dome enclosure Ino Pont name Funcion Gomeci n ote Network To connect to standard Power input Power input port Input DC 2 2 Framework and Dimension Please refer to the following two figures for dimension information The unit is mm See Figure 2 2 and Figure 2 3 Figure 2 3 Dimension illustration 2 3 Device Installation Important Make sure that the installation area is strong enough to hold the product such as a concrete ceiling Install the camera in the foundation area of the architecture or where sufficient strength is assured If a wall or ceiling board such as plasterboard is too weak to support the total weight the area shall be sufficiently reinforced Please see Figure 3 1 and Figure 3 2 3 1 Installation Steps for Plastic Dome Please follow the steps listed below to install the device Please refer to Figure 3 1 for reference Step 1 Rotate decoration ring clockwise and take it out Step 2 Affix the installation template label accessory to the ceiling or wall and use a pen to mark the positions of the screws and cable mounting hole in the ceiling or wall Remove the installation template label and attach the camera with 3 screws locally procured Step 3 Loosen the M3X8 cross pan head screw on pedestal and be careful do not loosen completely Now you can adjust position according to monitoring area Af
7. out Figure 4 2 Search interface 2 If you want to modify the device IP address without logging in the device web interface you can go to the configuration tool main interface to set In the configuration tool search interface Figure 4 1 please select a device IP address and then double click it to open the login interface Or you can select an IP address and then click the Login button to go to the login interface See Figure 4 3 In Figure 4 3 you can view device IP address user name password and port Please modify the corresponding information to login Please note the port information here shall be identical with the port value you set in TCP port in Web Network interface Otherwise you cannot login the device If you are using device background upgrade port 3800 to login other setups are all invalid IP Address 192 168 0 10 User Name famin pe Password Port 37777 Figure 4 3 Login prompt After you logged in the configuration tool main interface is shown as below See Figure 4 4 Netfork Paraneter PPPOE System Information Systes Uperade General Parameter IP Address 192 168 010 255 255 0 0 10 15 0 1 0 01 Return Figure 4 4 Main interface For detailed information and operation instruction of the quick configuration tool please refer to the Quick Configuration Tool User s Manual included in the resources CD 10 5 Web Operation This series net
8. reboot the device via the software to make sure the setup has been updated to the storage medium The general power adapter can work ranging from 0 C to 40 C The device may result in unstable power supply when the temperature exceeds the working temperature Please replace an industry level power adapter if you are using in the harsh environments 13 Note e This user s manual is for reference only Slight difference may be found in user interface e All the designs and software here are subject to change without prior written notice e All trademarks and registered trademarks mentioned are the properties of their respective owners e If there is any uncertainty or controversy please refer to the final explanation of us 14
9. se refer to the Web Operation Manual included in the resource CD for detailed operation instruction 12 I can not boot up the device or operate properly The water leakage occurred IR video is poor Please click RESET button for at least five seconds to restore factory default setup The unauthorized front or rear cap remove many result in water leakage The glass front cap has sustained heavy push or strike The weatherproof plug of the rear cap becomes loosen Do not use the proper supplying power The IR light can not turn on completely The object is out of the IR distance range of current device IR CUT does not turn to the night mode The photosensitive chip of the front end can not sense the IR light l can not upgrade the device via network When network upgrade operation failed you can use port 3800 to continue upgrade I can not login the client end or the WEB The Active X control is blocked The display card version shall be dx8 1 or higher Network connection error occurred Invalid network setup Invalid ID or PWD I can not play the download file To guarantee setup update Power adapter There is no player There is no DX8 1 or higher For the MEDIA PLAYER there shall be Div X503Bundle exe plugin if you play the AVI file For Windows XP user you need to install the plugin DivX503Bundle exe and ffdsho 2004 1012 exe After you modified the important setup please
10. sition Please make sure it reaches the original position otherwise it may result in water leakage Step5 Put the dome back to the gland cover Please refer to step4 in chapter 3 1 to install the decoration ring back RESET Button Figure 3 5 Reset 4 Quick Configuration Tool 4 1 Overview Quick configuration tool can search current IP address modify IP address At the same time you can use it to upgrade the device Please note the tool only applies to the IP addresses in the same segment 4 2 Operation Double click the ConfigTools exe icon you can see an interface is shown as in Figure 4 1 In the device list interface you can view device IP address port number subnet mask default gateway MAC address and etc Device List SN IP Address Port Subnet Mask Default Gateway Mac Address 1 192 168 1 108 3TTTT 255 255 255 0 192 168 1 1 1 s n gt ip an click login button directly and then input corresponding information to login ALL y Upgrade Refresh Login Logout Figure 4 1 Search interface 1 Select one IP address and then right click mouse you can see an interface is shown as in Figure 4 2 Select the Open Device Web item you can go to the corresponding web login interface Device List SM__ IP Address i eae x u gt Tip You can click login button directly and then input c nding information to login fa y Upgrade Refresh Login Log
11. ter adjustment fasten the M3X8 cross pan head screw with sheeting Step4 Rotate decoration ring bottom up and face the three spigots toward the three slots When you hear a Ca sound it is rotated in place Installation Pedestal M3X8 Cross Recessed Pan Head T3X18 Self tapping Screw Screw and preforming Gland Cover p 2 j Decoration Ring Dome Body Figure 3 1 Device installation illustration 1 Important Please pay attention to the dome camera direction when you are installing Please refer to the following figure for detailed information See Figure 3 2 Up Eletromagnetic Value Motor IR Lamp Photovaristor or IR lamp in dotted line Figure 3 2 Device installation illustration 2 Note This series product supports two cable exits One is from the bottom and the other is from the side Please refer to the following figure for cable exit from the side information Figure 3 3 Device installation illustration 3 3 2 Restore Factory Default Setup Introduction Important Please use RESET button when device is running Step1 Please refer to step1 and step2 in chapter 3 1 to loose the dome body Push a little bit you can take the dome body from the gland cover Step2 Take the dome body out and then turn the top cover hard to remove Step3 Slightly press the RESET button to complete the reset function See Figure 3 4 Step4 Turn the top cover back to the original po
12. to the following sheet for network camera performance specification ee EE K EF134L02E K EF134L03E K EF134L06E J9 OWeIeg O9PIA Main Processor High performance DSP OS Embedded LINUX System Resources Support real time network local record and remote operation at the same time User Interface Remote operation interface such as WEB Mobile EMS EMS System Status Image Sensor Bit stream statistics log and software version 1 3 inch MOS Pixel 1280 H 960 V Day night Support day night mode switch Gain Control Manual Auto White Balance Manual Auto BLC On Off Exposure Mode Auto Low noise Low motion blur Manual It ranges from 1 3 to 1 100000 Video Compression Standard H 264 MJPEG Video Frame Rate stream 1 1280 960 30fps stream 2 704 480 30fps Video Bit Rate H 264 32Kbps 8192Kbps MJPEG adjustable and bit rate is adjustable Support customized setup Video Flip Support mirror Support flip function Snapshot Max 1f s snapshot File extension name is JPEG Privacy Mask Supports max 4 privacy mask zones Video Setup Support parameter setup such as bright contrast Video Information Channel title time title VMD camera masking Lens 2 8mm Fixed focus 3 6mm Fixed focus 6mm Fixed focus Lens Interface M12 Lens is the default accessories 396 18 22 detection zo
13. ts one channel video data transmit to network terminal and then decode Delaying time is within 270ms network bandwidth support needed Network e Max supports 20 connections and output bandwidth is 32Mbps System Monitor refuses new connection request once it exceeds the bandwidth threshold Adopt the following video transmission protocol HTTP TCP UDP MULTICAST RTP RTCP RTSP and etc Support web access Realize network camera configuration and management via Ethernet Support device management via web or client end Support various protocols External power adapter DC 12V Support PoE Please refer to specifications Power Warning Do not connect these two power supplying sources to the device at the same time it may result in device damage Network Management Support picture parameter setup such as electronic shutter and gain setup Backlight compensation screen auto split to realize backlight compensation to adjust the bright e Log function e Support VMD e Support system resource information and running status real time display Assistant e Day Night mode auto switch Function e 8 function Support digital WDR Support video watermark function to avoid vicious video modification Built in IR light Support IR night vision The enclosure conforms to the IP 66 protection Has the weatherproof Support dual bit streams ACF 1 3 Specifications Please refer
14. work camera products support the Web access and management via PC Web includes several modules Monitor channel preview system configuration alarm and etc 5 1 Network Connection Please follow the steps listed below for network connection e Make sure the network camera has connected to the network properly Please set the IP address subnet mask and gateway of the PC and the network camera respectively Network camera default IP address is 192 168 0 10 Subnet mask is 255 255 255 0 Gateway is 192 168 0 1 e Use order ping network camera address to check connection is OK or not 5 2 Login and Main Interface Open IE and input network camera address in the address bar See Figure 5 1 Blank Page Windows Internet Explorer aboutiblank e Input your IP gt address here Internet R100 Figure 5 1 IP address The login interface is shown as below See Figure 5 2 Please input your user name and password Default ID is admin and PWD is 12345 Note For security reasons please modify your password after you first login 11 Figure 5 2 Web login If it is your first time to log in system pops up warning information to ask you whether install web plug in or not after you logged in for one minute For detailed plug in installation please refer to the Web Operation Manual included in the resource CD After you logged in you can see the main window Plea
Download Pdf Manuals
Related Search