user manual - Paintball Solutions
Contents
1. Treat every marker as if it were loaded Never look down the barrel of a paintball marker Keep your finger off the trigger until ready to shoot Never point the marker at anything you don t wish to shoot Keep the marker on safe until ready to shoot Keep the barrel blocking device in on the marker s muz zle when not shooting Always remove paintballs and propellant source before disassembly After removing propellant source point marker in safe direction and discharge until marker is degassed Store the marker unloaded and de gassed in a secure place Follow warnings listed on propellant source for handling and storage Do not shoot at fragile objects such as windows Every person within range must wear eye face and ear protection designed specifically to stop paintballs and meeting ASTM standard F1776 Always measure your marker s velocity before playing paintball and never shoot at velocities in excess of 91 44 meters 300 feet per second sS MONGOOSE 68 CALIBER ELECTRONIC PAINTBALL MARKER Meets or exceeds ASTM standards WARRANTY INFORMATION STANDARD WARRANTY The manufacturer warranties to the original customer that this product is free from defects in material and workmanship under normal use and service for a period of 90 days from the original date of purchase by the initial owner purchaser The manufacturer agrees to repair or replace at its discretion any2. product within a reasonable period of time This warranty does not cover o rings scratches nicks normal wear and tear of parts any modifications or normal fading of anodizing or damage caused by dropping or hitting of the product This warranty shall not apply if it is shown by the manufacture that the consumer caused the defect or malfunc tion because of misuse This warranty only covers original factory parts Any modifications or tampering of original factory parts will not be covered by this warranty Warranty work can only be con ducted by the manufacture technicians and or authorized techni cians If product needs to be repair package it carefully and send it together with your name address phone number and a brief description of the malfunction to Paintball Solutions 570 Mantua Blvd Sewell NJ 08080 EXTENDED WARRANTY By returning the enclosed warranty registration card or regis tering your warranty on line at www paintballsolutions com within fifteen days of purchase the warranty will automatically be extended to one year PAINTBALL potom Thank you for purchasing this Mongoose Paintball Marker The Mongoose represents the culmination of a great deal of research by the Diablo Paintball staff along with input from play ers such as you The Mongoose is designed to deliver many advent at a reasonable price With its 21 ball per second cycling rate the Mongoose is one of the fastest markers available at any pric
3. 3 Make sure the barrel blocking device is properly installed 4 Press and hold Command Button 5 seconds until LEDs light up LEDs will light in order and then turn off in reverse order The marker is now on but in Safe mode Turning off the Safety 1 Make sure that you and anyone within range are wearing eye protection designed specifically for paintball 2 Point the marker in a safe direction 9 Make sure the barrel blocking device is properly installed 4 With LEDs lighting in order and then turning off in reverse order press and release Command Button A CAUTION The marker is now ready to fire IPAINTBALEL Turning Off the Eyes Point the marker in a safe direction Make sure the barrel blocking device is properly installed With the marker powered up and off Safe press and release Command Button The top LED green will go out this indicates that the marker s anti chop eyes are off Note You will need to turn the eyes off to allow cycling of the marker without paintballs Boc A CAUTION DO NOT use the anti chop eyes as a safety device Turning on the Eyes 1 Point the marker in a safe direction 2 Make sure the barrel blocking device is properly installed 3 With the marker powered up and off Safe press and release Command Button 4 The top LED green will turn on this indicates that the marker s anti chop eyes are on Note You will need to turn the eyes off to allow cycling of the marker withou
4. 300 feet per second Higher velocities are not only potentially dangerous they often result in a substan tial increase in paintballs broken in the marker 1 2 Confirm that Barrel Plug is properly installed the On Off switch is in the Off position and the Bolt Pull Pin is cocked to the rear Using a 5 64 hex key make sure the Locking Set Screw 12B is backed out without removing it Make sure that you and anyone within range is wearing eye protection designed specifically for paintball While pointing the paintball marker in a safe direction remove the barrel plug and move the On Off switch to the On position IPAINTBALEL ooo 10 11 12 13 Point the marker over the chronograph and in a safe direction Pull the trigger and observe the reading on the chronograph To increase the velocity turn the Velocity Adjuster 12 clockwise To decrease the velocity turn the Velocity Adjuster counter clock wise Once the desired velocity has been reached use the 5 64 hex key to turn the Locking Set Screw in until it binds against the Hammer Plug This will prevent the velocity adjuster from moving during play and is required on most playing fields Move the On Off switch to the Off position Insert Barrel Plug Proceed to playing field Keep the On Off switch in the Off position and barrel plug in place until ready to play and instructed to remove the barrel plug by a playing field staff member DIE GASSI
5. A WARNING This is not a toy Misuse may cause serious injury or death Eye protection designed specifically for paintball must be worn by the user and persons within range Recommend 18 years of age or older to purchase Persons under 18 years of age must have adult supervision READ OWNER S MANUAL BEFORE USING bias a Hi b 9 P cz Y lt Aoc Y A www diablopaintball com LL P T p T M d k 1L Wt a mee _ p E E T c _ LM M E 4 a k t T BEBE md c 1t 9 demie i hii 75 ad i Tm a E 68 CALIBER ELECTRONIC PAINTBALL MARKER Meets or exceeds ASTM standards TABLE OF CONTENTS Page 1 O OND FW DP 11 12 13 14 15 17 Topic s Warning and Rules Safe Marker Handling Warranty Information Welcome Initial Assembly Parts Key Exploded Diagram Battery Installation Attaching Feeder Hopper Attaching Propellant Source Chronographing Loading Paintballs De Gassing Maintenance Storage Trouble Shooting Guide Notes Warranty Registration IPAINTBALE A WARNING This is not a toy Misuse may cause serious injury or death Eye protection designed specifically for paintball must be worn by the user and persons within range Recommend 18 years of age or older to purchase Persons under 18 years of age must have adult supervision READ OWNER S MANUAL BEFORE USING AUN O1 11 12 RULES OF SAFE MARKER HANDLING
6. Jj4 duc Buu O esf niniw M9J2S 1ueuusn py JoyejnBey v Je1depy yueL jueieg Ieg Mm 19S S Bupbpo1 g Buly O uonejgiA nuy v Jaysnipy Aj20 8A jueunsn py peeJdue v YOON pee4J EJHA uid dois ane Bnid sec NLA Buuds eA eA yeas dno anljeA Seo uld 19H09 v uld diis oino yng Buuds ped I 099H 6Buuds uen JOWWeH WEeN Hed 8c 9c Sc ve c c LZ oz 6L LL 9L vi L cL LL oOnNooo E V Z L JequinN ued ADI S LelVd ee the Rate of Fire Point the marker in a safe direction Make sure the barrel blocking device is properly installed Press and release the Adjustment Button to change the rate of fire see table 1 for LED representation of firing rates Eyes On Off 20 BPS 16 BPS 12 BPS 10 BPS 8 BPS 6BPS Table 1 Turning On the Safety powering down the marker 1 gh oh Make sure that you and anyone within range are wearing eye protection designed specifically for paintball Point the marker in a safe direction Make sure the barrel blocking device is properly installed Press and hold Command Button 5 seconds until all LEDs go off The marker is now OFF BATTERY INSTALLATION 1 2 3 Find the On Off switch located on the left side of the marker just above the Left Grip Panel 36 Make sure the switch is in the Off position which is toward the rear of the marker Using a screwdriver remove the three Grip Panel Screw
7. NG T oe to v D Make sure that you and anyone within range is wearing eye protection designed specifically for paintball Set the On Off switch to the Off position Point the marker in a safe direction If you are using a motorized feeder turn it off Twist the Clamp Feed Adjustment 11A in a counter clockwise direction until loose Invert the marker so that the hopper feeder is upside down so that paint balls are no longer feeding into the marker Remove the hopper feeder from the marker Twisting the barrel in a counter clockwise direction remove it from the marker While pointing the paintball marker in a safe direction move the On Off switch to the On position moncoose 68 CALIBER ELECTRONIC PAINTBALL MARKER Meets or exceeds ASTM standards 10 Pull the trigger and allow the marker to cycle to confirm the absence of paintballs in the marker s breech If a ball discharges repeat until no more paintballs come out of the marker WARNING When removing the cylinder from the marker it could fly off with enough force to kill if the valve unscrews from the cylin der LOOK at valve when removing cylinder STOP if valve starts to unscrew from the tank Screw it back on and take it to a trained per son for repair 11 Unscrew the propellant cylinder approximately one complete revolution 12 Pull the trigger until the marker fails to recock if this takes more than 10 shots unscrew the cylinder an
8. additional 1 2 turn and repeat 13 Remove See Warning Above the propellant cylinder MAINTENANCE Bolt 1 Pull the Bolt Pull Pin 28A upwards until it clicks 2 Pull the Bolt Pull Pin rearward until the Bolt 28 comes out of the back of the Main Body 34 3 Clean the bolt thoroughly to include rinsing in warm water if needed 4 Lubricate the bolt with non corrosive lubricant such as Empire Lube or Empire Oil 5 Return the bolt to the rear of the Main Body making sure to put the open end in first 6 Slide the bolt forward until the Bolt Pull Pin lines up with the hole in the top of the Hammer 1 T Press the Bolt Pull Pin downward until it clicks in place PAINT EIAS Cleaning Lubricating Assembly 1 De gas the marker according to previous directions 2 Wipe all outer surfaces with a clean soft cloth or paper towel 3 DO NOT submerge marker in water or cleaning solutions This may destroy the circuit board and will void your warranty 4 Remove and service Bolt as previously instructed 5 Remove the Retainer Clip from the end of the Quik Strip Pin 5 6 While maintaining some pressure on the back of the Hammer Plug 24 pull out the Quik Strip Pin f Remove the Main Spring 2 Recoil Pad 3 Spring Strut 4 and Hammer Plug 24 from the marker 8 Using a 1 8 hex wrench remove both Grip Frame Screws 21 from the Grip Frame 35 NOTE that these are located on the trigger frame and NOT on
9. e The Vise Grip Feed Neck Quik Strip Delrin bolt vertical expansion chamber ported barrel and inline regulator are all fea tures usually available on much pricier markers or only through a great deal of after market expense We believe that the affordability of a reliable feature packed marker will improve your playing expe rience and winning percentage While winning isn t everything it sure beats the alternative Play hard play safe play to win NNUS MONGOOSE 68 CALIBER ELECTRONIC PAINTBALL MARKER Meets or exceeds ASTM standards Numbers shown in parentheses following part names correspond to the numbers on the Parts key located on the centerfold pages of this manual INITIAL ASSIEMBLY 1 Screw Barrel 23 hand tight into the Main Body 34 making sure the Barrel O Ring 16 is properly seated between the Barrel and the Main Body to prevent the Barrel from vibrating loose during rapid firing 2 Screw Volumizer 26 hand tight into the Vertical ASA 33 making sure a Multi use O Ring 16 is properly seated between the Volumizer and the Vertical ASA to properly seal this connection 3 Screw Velocity Adjuster 12 into the Hammer Plug 24 approximately 2 complete turns 4 Insert the Barrel Plug into the end of the Barrel 23 LED OPERATIONS Powering up 1 Make sure that you and anyone within range are wearing eye protection designed specifically for paintball 2 Point the marker in a safe direction
10. orized hopper such as the Diablo TSA or Empire Reloader B 1 2 Confirm that Barrel Plug is properly installed and the On Off switch is in the Off position Twist the Clamp Feed Adjustment 11A in a counter clockwise direction until it is loose but do not remove If accidentally removed screw back on one complete turn Press neck of Feeder Hopper into the Vertical Feed Neck 11 until completely seated MONGOOSE 68 CALIBER ELECTRONIC PAINTBALL MARKER Meets or exceeds ASTM standards Orient the Feeder Hopper so that the lid is facing the rear of the marker and the Feeder Hopper is parallel to the Main Body 34 Twist Vise Ring in a clockwise direction until it fits snugly against the Feeder Hopper neck LOADING PAINTBALLS The performance of your marker is directly related to the quality of paintballs used We highly recommend Diablo paintballs to give you satisfaction and success on the playing field 1 2 Confirm that Barrel Plug is properly installed and the On Off switch is in the Off position Point marker in a safe direction and load paintballs in the Feeder Hopper If you are using a non motorized hopper be sure to leave some room in the hopper for the balls to feed properly CHRONOGRAPHING Never operate your marker without first checking the velocity and confirm ing that you are firing below that required on the field of play At no time should the marker fire paintballs in excess of
11. s 20 from the left side side facing you if the barrel is pointing to your left of the Grip Panel 36 IPAINTBALEL Install 9 volt battery Push the On Off switch forward towards the On position Confirm that the LED light located on the grip is lit to signify that the battery is good and properly installed Push the On Off switch forward towards the Off position Replace Grip Panel using the three Grip Panel Screws being careful not to pinch the wires leading to the battery connector and those leading to the circuit board ATTACHING PROPELLANT SOURCE 1 2 o BO f Confirm that Barrel Plug is properly installed Cock the marker by pulling the Bolt Pull Pin 28A in the rearward direction until it clicks into place This compresses the Main Spring 2 and allows the Valve Stem Seal 7 to properly seat Confirm that the On Off switch is in the Off position Point the marker downward and in a safe direction Place the leading end of the propellant cylinder threads into the threaded interface of the Tank Adapter 14 Without pushing twist the propellant cylinder in a clockwise direction and allow the cylinder threads to draw it into the Tank Adapter DO NOT force the cylinder which could cause cross threading Screw the propellant cylinder completely in until it is firmly seated ATTACHING FEEDER HOPPER Due to the extremely high rate of fire capability of this marker we highly recommend the use of a mot
12. t paintballs A CAUTION DO NOT use the anti chop eyes as a safety device Preparing to Change Rate of Fire 1 Make sure that you and anyone within range are wearing eye protection designed specifically for paintball 2 Point the marker in a safe direction 3 Make sure the barrel blocking device is properly installed 4 Using a Phillips head screw driver remove the tournament cover to the Adjustment Button moncoose 68 CALIBER ELECTRONIC PAINTBALL MARKER Meets or exceeds ASTM standards Area Aew uBisep jeny pepnpur Bnjg jaueg Ajuo uoisieA AOT UI s oneueuog U UMOUS ION 19409 e A3 1uBiu 49 02 e 3 19 Jes eA3 ueeJloS q21 pee M peg SM9JOS peog PND SM9J0S 18S piouejosS SM8J9S YMS HO UO p1eog UNIO piouejos YOUMS 196p sseu1ep BuurM dey 1ojein amp eu uoisig JoyejnBay SJ9USEeM pojo eg Uld eAug 101ejnBeu eBneo Sd 0021 0 Jebbu Buuds seas yeas oiu04129 3 s eueg duc eujeJ4 duc pog ule VSV 911J9A nJu Seo SM9J9S PeMIO doiq pemo doiq Bune g eg a Buudg 9 MOINS 18S g uid Bunoeuuo Vv owen L3 OLA 63 83 Z3 93 Sd va d cg L3 vH d ed LH ev OV 8 Ze 9 GE ve ee c oe 8c JequinN Hed spyepueis N LSY speeoxe 10 sjee A rivo 89 QE FWAEN E AIF Wal yog Jaqueuyd ejnssaJd MOT sui eur oie v 9Ur seo Bnjg 1euiueH pueg A 91J9S VSV E 9Iu9A SM9JOS 9uueJ4 duc SM9JOS eueg dut SM9JoS eumuonog 19S Uld eue
13. the Main Body 9 Pull the Trigger Frame away from the Main Body 10 Remove the Hammer 1 from the rear of the Main Body 11 Lubricate the Hammer with a non corrosive lubricant such as Empire Lube or Empire Oil 12 Replace the Hammer with the open end facing rearward and the flat side down 13 Insert the Bolt 28 in the top of the Main Body 14 Line up the hole in the bolt with that in the Hammer and push the Bolt Pull Pin downward until the two are linked together This will prevent the Hammer from rotating during assembly 15 Place the Main Spring 2 Recoil Pad 3 Spring Strut 4 and Hammer Plug 24 back in the marker 16 While holding the Hammer Plug in place replace the Quik Strip Pin 5 and secure with the R Clip 5A STORAGE Always turn off the marker remove the hopper feeder all paintballs and propel lant source and place it in a secure location where it cannot be accessed by unauthorized persons MONGOOSEC 68 CALIBER ELECTRONIC PAINTBALL MARKER Meets or exceeds ASTM standards TROUBLE SHOOTING GUIDE Symptom Does not Fire Leaks air down Barrel Leaks Air From ASA Bottle Interface Does Not Re cock Goes Full Auto Excessive Ball Breakage Cause Not Cocked Not On Bad Battery Out of Gas Bad Cup Seal 7 Bad Bottle O Ring Low on Gas Sear Not Catching Low on Gas Bad Striker O Ring Low Quality Paintballs Ball Chopping NOTES ON MONGOOSE C
14. ure Cock the Bolt Pull Pin 28A to the rear Turn Switch On Replace Battery Refill or Replace Propellant Source Replace Cup Seal 7 Replace Bottle O Ring Refill or Replace Propellant Source Tighten Grip Frame Screws 21 Refill or Replace Propellant Source Replace Multi use O Ring 16 located on front of Striker Use better Paintballs Such as Diablo Brand Use motorized feeder Such as Diablo TSA When in doubt thoroughly clean and lubricate the marker Many marker function problems are caused by excessive dirt or lack of lubrication NOTES ON MONGOOSE WARRANTY REGISTRATION To assist us in providing the best customer service possible and to increase your warranty from 90 days to one year at no additional cost Complete and mail this to Paintball Solutions 570 Mantua Blvd Sewell NJ 08080 Or register online at www paintballsolutions com Name Address City State Zip Country Email Address Serial Number located on left side of marker Date of Purchase Place of Purchase be MONGOOSE PAINTBALL 68 CALIBER ELECTRONIC PAINTBALL MARKER Meets or exceeds ASTM standards
Download Pdf Manuals
Related Search