User Manual - Box Design by Pro
Contents
1. BY PRO JECT AUDIO SYSTEMS INSTRUCTIONS FOR USE Pro Ject Amp Box DS Mono Dear music lover thank you for purchasing a PRO JECT AUDIO amplifier In order to achieve maximum performance and reliability you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse 5 Important notice Safety instructions AC outlet voltages vary from country to country Before connecting to the mains make sure that the voltage in your area meets the voltage requirements printed on the power supply The power cord is used to disconnect the unit from the mains Make sure that the power cord is easily accessible at all times Never handle the device the power cord power supply while your hands are wet or damp y Avoid letting liquids enter the device or the power supply Never place any item containing liquid such as a flower vase on or near the device Never spill any liquid on the device or the power supply Never place any naked flame sources such as lighted candles on or near the device The product shall not be used in damp or wet locations next to a bathtub sink swimming pool or any other similar conditions Connectors CE rons O SN 2x48V O Trigger Pro Ject Audio System Vienna Austria OUT IN Amp Box DS Mono Make all connections whilst the amplifier is disconnected from the power supply Only connect one loudspeaker with an impedance not2. Mono Power output 125W 195W at 8 ohms 4 ohms Frequency response 10Hz 50kHz 0dB 3 Noise floor gt 90dB A weighted THD lt 0 1 at POW Gain 26 Pre in 1 pair RCA phono sockets Input sensitivity 1 5V Input impedance 100kohms Speaker connectors 4mm banana plugs spades connectors or naked wire Trigger 12V DC switching voltage Trigger in and out 2 pole co axial 2 5mm co axial jack Outboard power supply 48V 2 5A DC suitable for your country s mains supply Power consumption 2 5A DC lt 1W in standby Dimensions W x H x D D with sockets 103 x 72 x 144 163 mm Weight 1 2909 without power supply Service Should you encounter a problem which you are not able to alleviate or identify please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer Copyright PRO JECT is a Registered Trademark of Lichtenegger The information was correct at the time of going to press The manufacturer reserves the right to make This guide was produced by Audio Trade GmbH changes to the technical specification without prior Copyrig
3. less than 4 ohms y Red terminal carry the positive signal black connections the negative signal Make sure the polarity of the connection is correct at each end of the cables Never use any other power supply than the one supplied with the unit Connection to the preamplifier Both RCA cinch sockets are for connecting the cables from your pre amp or AV processor The preamplifier signal can be relayed to further units via the second socket Connection to the speaker The output terminal accept loudspeaker cables terminated with 4mm Banana plugs spades connectors or naked wire Mains power connection Connect the low voltage plug from the power supply to the 2x48V socket of the amplifier before connecting the power supply to the mains 2 Audio Trade GmbH Pro Ject Amp DS Mono Revision 2013 1 15 Remote power on The amplifier can be switched on amp off via a special connection from the Pro Ject Pre Box SE via the 2 5mm socket marked Trigger IN A 45cm long power on cable polarity is supplied for this purpose Longer cables are available as accessories The remote power on signal can be relayed to further units via the Trigger OUT socket To switch on from standby or to standby The pushbutton on the front panel of the unit alternately turns the power on or returns it to standby mode The blue LED on the front panel shows that the unit is powered on Technical specifications Pro Ject Amp Box DS
4. ht 2012 All rights reserved notice as deemed necessary to uphold the ongoing process of technical development Audio Trade GmbH Pro Ject Amp Box DS Mono Revision 2013 1 15 3
Download Pdf Manuals
Related Search