8846 - Harbor Freight Tools
Contents
1. and an explanation of the complaint must accompany the merchandise If our inspection verifies the defect we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement We will return repaired products at our expense but if we determine there is no defect or that the defect resulted from causes not within the scope of our warranty then you must bear the cost of returning the product This warranty gives you specific legal rights and you may also have other rights which vary from state to state PITTSBURGH 3491 Mission Oaks Blvd PO Box 6009 Camarillo CA 93011 800 444 33532. Owner s Manual amp Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions assembly operating inspection maintenance and cleaning procedures Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number Keep this manual and the receipt in a safe and dry place for future reference PITTSBURGH Heavy Duty Jack Stands Item 38846 shown 38846 38847 34924 3 Tons 6 000 Ib 6 Tons 12 000 Ib 12 Tons 24 000 Ib 11 3 4 16 3 4 __ 15 1 8 24 19 112 30 1 8 Evenly distributed across two Jack Stands Visit our website at http www harborfreight com REV 13a Email our technical support at tech harborfreight com When unpacking make sure that the product is intact and undamaged If any parts are missing or broken AWARNING please call 1 800 444 3353 as soon as possible Copyright 2011 by Harbor Freight Tools All rights reserved No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product any shape or form without the express written consent of Harbor Freight Tools Failure to do so can result in serious injury Diagrams within this manual may not be drawn proportionally Due to continuing SAVE THIS MANUAL improvements actual product may differ slightly from the product described herein Tools required for assem
3. Repeat Steps 1 through 3 above with the other Jack Stand Page 2 For technical questions please call 1 800 444 3353 Pawl not shown Jack Stands Supporting a Vehicle WARNING Use as matched pair to 5 Following the instructions in your floor jack support one end of a vehicle only manual raise your vehicle to just above the minimum height of your Jack Stands 1 Make sure the vehicle does not exceed the capacity of the Jack Stands 6 Slide your Jack Stands to the proper position a E l l points referred to in the vehicle owner s manual Note Capacity is evenly distributed weight per pair Make sure the Jack Stands are on the same of Jack Stands Only apply the load vertically point on each side of the vehicle Move the Handle up and raise the Jack Stands until they are just below the jack contact point on the vehicle Center the load on the Saddle of the Post Release the Handle so that ratchet catches on the Pawl Gently lower the vehicle with the floor jack 2 Examine Jack Stands for cracks or damage before each use Do not use if even a minor crack bend or other damage deformation appears Discard Jack Stand if damaged or deformed 3 Raise the Handle on each Jack Stand It may drop down a very small amount until the to completely lower the Post ratchet catches on the Pawl Repeat on other side 4 If your are raising only one end of the vehicle WARNING Set both the Jack Stands to the same height block th
4. S THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO Limited 90 Day Warranty Harbor Freight Tools Co makes every effort to assure that its products meet high quality and durability standards and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase This warranty does not apply to damage due directly or indirectly to misuse abuse negligence or accidents repairs or alterations outside our facilities criminal activity improper installation normal wear and tear or to lack of maintenance We shall in no event be liable for death injuries to persons or property or for incidental contingent special or consequential damages arising from the use of our product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation of exclusion may not apply to you THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS To take advantage of this warranty the product or part must be returned to us with transportation charges prepaid Proof of purchase date
5. bly and service may not be included IMPORTANT SAFETY INFORMATION A WARNING Read all safety warnings and instructions Failure to heed these markings may result in personal injury and or property damage Save all warnings and instructions for future reference The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator Study understand and follow all instructions before operating this device 2 Do not exceed rated capacity Be aware of dynamic loading Sudden load movement may briefly create excess load causing product failure 3 Use only on hard level surfaces 4 Center load on saddle 5 Use as matched pair to support one end of a vehicle only 6 Wear ANSI approved safety goggles and heavy duty work gloves during use 7 Do not use for aircraft purposes 8 Support vehicle only at manufacturer recommended locations 9 Inspect before every use do not use if parts loose or damaged 10 Examine Jack Stands for cracks or damage before each use Do not use if even a minor crack bend or other damage deformation appears Discard Jack Stand if damaged or deformed 11 12 13 14 15 16 17 18 19 Keep work area clean Cluttered areas invite injur
6. e tires that remain on the ground 7 Determine if the vehicle is stable If not raise the vehicle and reposition the Jack Stands Removing the Jack Stands 1 Raise the vehicle with a floor jack to take 3 Remove the Jack Stands Use the floor jack the load off of the Jack Stands to safely lower the vehicle to the ground 2 Raise the Handle on the Jack WARNING Do not use Jack Stands as a permanent Stands and lower the Posts stand for the vehicle Use them only while making repairs then immediately lower vehicle to the ground Parts List and Diagram Note 1 Pair includes two each of the following parts KZ lt gt Part Description _ Saddle SE Record Serial Number Here Note If product has no serial number record 3 month and year of purchase instead Note Some parts are listed and shown for illustration purposes only and are not available 1 individually as replacement parts Jack Stands For technical questions please call 1 800 444 3353 Page 3 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT IN FACT THE MANUFACTURER AND OR DISTRIBUTOR EXPRESSLY STATE
7. ies Observe work area conditions Keep work area well lighted Keep children away Children must never be allowed in the work area When not in use tools must be stored in a dry location to inhibit rust Use as intended only Do not wear loose clothing or jewelry as they can be caught in moving parts Protective electrically non conductive clothes and non skid footwear are recommended when working Wear restrictive hair covering to contain long hair Maintain tools with care Keep tools clean for better and safer performance Stay alert Watch what you are doing use common sense Do not operate any tool when you are tired Do not operate tool if under the influence of alcohol or drugs Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs If there is any doubt do not operate the tool Assembly 1 2 Take a Post and face the ratchet edge toward the front of the Base The Pawl is on the front Lift the Handle and lower the Post into the Base Make sure it is completely lowered CAUTION Be alert to pinching danger when lowering the Post 3 On the opposite side of the Handle there is a tab on the Base Using a small punch and hammer sold separately bend the tab in Bend the tab in enough to keep the Post from coming out of the Base WARNING Before using the Jack Stands make sure the Post cannot be pulled up and out of the Base 4
Download Pdf Manuals
Related Search