LS Human Machine Interface DATA SHEET LS Industrial Systems
Contents
1. Fast Transient apie burst noise Voltage 1kV Ambient No corrosive gas or dust conditions ae 2 000m 6 562ft or less eight Self cooling 3 XGT Panel Function Specifications XGT Panel s function specification is as follows Type XP70 TTA Display type XP80 TTA XP90 TTA AC TFT color LCD 10 4 26cm 12 1 31cm 15 38cm Display resolution 640 x 480 pixel 800 x 600 pixel 1024 x 768 pixel 65 000 Color Left Right 65 deg Upper 45 deg Lower 75 deg CCFL Replacement is available Supporting automatic On Off 50 000 hour Display color Left Right 65 deg Display angle Upper 45 deg Lower 65 deg Backlight Backlight life Contrast Magnetic buzzer ARM920T 32bit RISC 200MHz Graphic accelerator Hardware Accelerator Left Right 75 deg Upper 50 deg Lower 60 deg Operating RAM Backup RAM Backup type Date Hour data and Logging Alarm Recipe data Approx 3 years Operating ambient temperature of 25 C 1 channel IEEE802 3 10 100Base TX ea Animation 2 Channels 1Channel RS 422 485 mode 1 Slot Compact Flash Option module is available Up to 4 language simultaneously GIF format is available Type XP70 TTA XP80 TTA Recipe Available Available Available CE UL KCC IP65F ao XP90 TTA AC Weight kg 1 Battery operation and life Battery is used to reserve backup data and RTC date time when power is off Because battery is used when power i2. XP70 TTA AC XP80 TTA DC XP80 TTA AC and XP90 TTA AC module For safety precautions on the HMI system refer to the XGT Panel user manual gt The precautions are divided into 2 sections Warning and Caution Each of the meanings is represented as follows N Warning Caution If violated instructions it can cause death fatal injury or considerable loss of property If violated instructions it can cause a slight injury or slight loss of products gt The symbols which are indicated in the HMI and User s Manual mean as follows ra This symbol means paying attention because of danger of injury fire or malfunction This symbol means paying attention because of danger of electrical shock gt Store this datasheet in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user N Warning Do not contact the terminals while the power is applied Risk of electric shock and malfunction Protect the product from being gone into by foreign metallic matter Risk of fire electric shock and malfunction Do not charge heat short solder and break up the battery It can cause injury and fire by explosion and ignition Be sure to check the rated voltage and terminal arrangement for the module before wiring work Risk of electric shock fire and malfunction Tighten the screw of terminal block with the specified torque range If the terminal screw looses
3. it can cause fire and electric shock Use the HMI in an environment that meets the general specifications contained in this datasheet Risk of electrical shock fire erroneous operation and deterioration of the HMI Be sure that external load does not exceed the rating of output module Risk of fire and erroneous operation Do not use the HMI in the environment of direct vibration Risk of electrical shock fire and erroneous operation Do not disassemble repair or modify the HMI Risk of electrical shock fire and erroneous operation When disposing of HMI and battery treat it as industrial waste Risk of poisonous pollution or explosion Precautions for use gt Do not use hard or pointed objects to operate the touch screen panel since it can damage the panel surface Make sure that the FG terminal is grounded with class 3 grounding which is dedicated to the HMI Otherwise it can cause disorder or malfunction of HMI Connect expansion connector correctly when expansion module is needed Do not detach PCB from the case of the module and do not modify the module Turn off power when attaching or detaching module Cellular phone or walkie talkie should be farther than 30cm from the HMI Input signal and communication line should be farther than minimum 100mm from a high tension line and a power line in order not to be affected by noise and magnetic field Before handling the product Before using the product r
4. by remodeling or repairing based on the user s own discretion 4 The troubles caused by improper usage of the product 5 The troubles caused by the reason which exceeded the expectation from science and technology level when LSIS manufactured the product 6 The troubles caused by natural disaster 3 This warranty is limited to the HMI itself only It is not valid for the whole system which the HMI is attached to
5. 2 gt Keep the length of cable within 500 m gt Recommends to using the shielded cable Cable specification gt Pin arrangement of XGT Panel s connector gt Connector type D Sub 9pin Female type Configuration and wiring Remark 1 Set terminal resistance of the XGT Panel 2 Because of female connector for XGT Panel Please use D SUB 9P male type for the connector 3 Please connect no 4 TX with no 8 RX no 5 TX with no 9 RX 6 Power input wiring 6 1 Power Supply Wiring XP70 TTA DC and XP80 TTA DC are connected to DC24V Frame Ground XP70 TTA AC XP80 TTA AC and XP90 TTA AC are connected to AC100 220V ACIDI FG Frame Ground unit mm Power terminal Less than 6 00mm Remark 1 When the regulation of power is bigger than provision use the constant voltage transformer 2 In case power has much noise use the insulation transformer 3 Separate the XGT Panel s power from the main circuit high voltage large current cable I O signal cable If possible install at a interval of more than 100mm 7 Installation 7 1 Panel cut unit mm Item X Y Z XP70 TTA XP80 TTA 294 5 227 5 XP90 TTA 383 5 282 5 7 2 Panel installation Keep the distance of 100 mm between XGT Panel and panel per each direction unit mm 100 100 100 7 3 Fixation The bracket is included in the product 1 Precaution for installation This machi
6. DATA SHEET LS Human Machine Interface XP70 TTA B DC XP70 TTA B AC XP80 TTA B DC XP80 TTA B AC XP90 TTA B AC When using LSIS equipment thoroughly read this datasheet and associated manuals introduced in this datasheet Also pay careful attention to safety and handle the module properly Store this datasheet in a safe place so that you can take it out and read it whenever necessary LS Industrial Systems Co Ltd Davis Controls Davis Controls Ltd ts the authorized distributor of LOIS quipment and control solutions throughtout Canada Founded in 1933 Davis Controls represents a strong and balanced portfolio of world class products From head office facilities located in Oakville Ontario Davis Controls connects customers seeking high quality automation solutions with global manufacturers of state of the art products You can contact us at Toll Free Canada 800 701 7480 Toll Free USA 300 288 4159 Email infoiidaviscontrols com Website wwiw dayviscontroals com Thank you for your business and your interest in LOIS solutions LS constantly endeavors to improve our products so that information in this datasheet is subjected to change without notice 103 10000880 0 y Safety Precautions Safety Precautions is for using the product safe and correct in order to prevent the accidents and danger so please go by them gt The precautions explained here only apply to the XP70 TTA DC
7. anel the communication parameter of the PLC controller set from the XP Builder 2 1 1 connection If LAN is not supported using cross cable is recommended It will gives fast and convenient to send receive project data 3 When designing the cables please make sure Modular Jack has no broken part such as Lock part it can gives poor connection And using a Plug Cover when designing Ethernet cable is recommended 5 2 Tool cable specification and wiring ptm sero gt Name PMC 310S Cable spedricaio Using for download and upload the project program P gt Length flexible tube type 1 m gt Directly connect to PC and XP Panel gt Providing the option production Configuration and wiring HOT Paral 5 3 RS 232C cable configuration and wiring oo otm Desertion O Cable gt Please use the AWG24 type spenificaidh gt Keep the length of cable within 15 m p gt Recommends to using the shielded cable Connect to PLC or control devices 1 1 communication gt Pin arrangement of XGT Panel s connector gt Connector type D Sub 9pin Male type Configuration and wiring Remark 1 Wiring precaution Because of male connector for XGT Panel Please use D SUB 9P female type for the connector Because PLC and control devices are different wiring methods please refer to communication manual for more detail 5 4 RS 422 485 cable configuration and wiring gt Please use the UL Style 2464 AWG2
8. ead the datasheet and the User s manual through to the end carefully in order to use the product efficiently po Name Ede XGT Panel Manual 10310000867 XGT Panel Communication Manual 10310000857 XP Builder Manual 10310000876 Revision History Updated Information 2007 12 First Edition 2009 4 XP70 80 TTA DC XP90 TTA AC types added 2010 8 Power consumption added for DC type 1 Introduction XGT Panel as HMI Human Machine Interface watches and controls the condition of the PLC Inverter and other instruments XGT Panel series provide the function which is various and a stable efficiency 2 General Specifications No Item Specifications Standard Ce a a temp 20C 60C 4 Operating eo l Hk 10 85 RH Non condensing Oe Storage e i 10 85 RH Non condensing po For discontinuous vibration Ssi lt oHz 35mm Vioration Deos Each 10 times in X Y Z IEC 61131 2 direcnons 5st lt 9Hz 175mm CAA Max impact acceleration 147 ms 15G Shocks Authorized time 11 ms Pulse wave Sign half wave pulse 3 times each in X Y and Z directions Square wave 1 000V LSIS Standard impulse noise 7 IEC 61131 2 Electrostatic IEC 61131 2 discharging Voltage 6 kV contact discharging IEC 61000 4 2 Radiated electromagnetic field noise IEC 61131 2 IEC 61000 4 3 Glass Power Communication module interface IEC 61131 2 IEC 61000 4 4 27 500 MHz 10 V m
9. ne should be install within 0 50 C otherwise the screen may be changed or cause malfunction Because the product can be affected by dust use the anti vibration rubber packing Don t touch the terminals while power is on otherwise it may cause electric shock or erroneous operation 8 Dimension 8 1 XP70 TTA unit mm aoni 243 0 a o o m m m o m M0000 517 0 DODIODIO000 0000000000000 DOOD000000000 00000000000 be Pa 8 2 XP80 TTA unit mm DODN0O0 000000000 000000000 0000000000000 MU a DOODOOODO00000TRTO000000 OOOOOOTOToO OOU OO OOOONN ae 00000000000000000000000000 8 3 XP90 TTA et gt 9 Warranty 1 Warranty period LSIS provides an 18 month warranty from the date of the production 2 Warranty conditions For troubles within the warranty period LSIS will replace the entire HMI or repair the troubled parts free of charge except the following cases 1 The troubles caused by improper condition environment or treatment except the instructions of LSIS 2 The troubles caused by external devices 3 The troubles caused
10. s off battery is not consumed when power is on 2 LCD Backlight replacement XP70 TTA and XP80 TTA LCD backlight can be replaced by technician 3 DC power supply is not supported on XP90 TTA 4 Wiring Precautions If AC Power is applied into the product for DC Power it may cause damage or fire 4 Part names of functions Part names of functions are as described below Tres vane anion 1 Analog touch panel User touch input Q Froni side 2 LCD screen display Indicates operation status of module Normal RUN status monitoring downloading the project data Initializing mode when booting Error occurs communication error project data error 1 Logging recipe screen data backup 2 Upgrade of Windows CE is available Power connection It consists of power input and FG terminal terminal It consists of 2 ports 1 USB memory connection logging recipe screen data backup USB interface 2 USB memory connection project data transmission backup 3 User interface connection use of mouse keyboard 4 Printer connection printing is available Extension port Extension module installation Reset switch Hardware reset switch RS 232C interface 1 Project data transmission Tool interface 2 Logging recipe alarm screen data backup 3 Machine software upgrade Module setting switch A setting Normal operation basic setting B setting When upgrading Windows CE LED Status Use of Watchdog basic se
11. tting B setting No use of Watchdog A setting RS 422 485 terminal resistor setting 1200 B setting No use of RS 422 485 terminal resistor Extension module fixing hall RS 422 485 port RS 422 485 PLC control machine communication RS 232C port RS 232C PLC control machine communication Ethernet 10 100 BASE TX 1 Project data transmission 2 Logging recipe alarm screen data backup 3 Machine software upgrade 4 PLC control machine communication FG terminal FG terminal hole for extension module Using the extension module fixing hall Ethernet port Remark 1 Using the no 5 FG terminal for the module s frame ground And Using the no 15 FG terminal for the extension module s frame ground 2 There is prevention sheet in prevention of battery discharge In order to use backup remove the prevention sheet 5 Communication cable configuration and wiring method 5 1 Ethernet cable configuration and wiring tem scription Cable gt Type UTP FTP STP cable Specification gt Specification CAT 5 Enhanced CAT 5 CAT 6 When communicating through LAN connected to network equipment like a switching hub direct cable is used for communication to PLC control devices 4 Direct cable lt lt Modular Jack When communication with computer PLC and control device directly without using a hub in this case cross cable is used 1 1 Cross cable L l pa Remark 1 Ethernet setting Ethernet IP sets from XGT P
Download Pdf Manuals
Related Search