Operating manual
Contents
1. atlantic SMARTER CLIMATE LIVING Operating manual AUSTRALIA Atlantic Australasia Pty Ltd 4 13 25 Church Street Hawton Victoria Street Australia Free call 1800 67 78 57 Phone 0398 52 95 99 Fax 03 98 52 98 94 Web www atlantics com au Email sales atlantics com au NEW ZEALAND Phone 0800 422 000 Fax 04 38 00 509 Web www atlantics co nz Email sales atlantics co nz QD Points de percage B n uv c perageA E RANGE ARTISAN TARRO Feet and castors not to be fitted on high and plinth models RANGE ODYSS E _ Kio zz A o o The product you have just purchased has undergone numerous tests and inspections to guarantee the highest quality We hope it will give you entire satisfaction INSTALLATION OF THE PANEL HEATER Please read the instructions before starting to install the heater Disconnect the power before carrying out any work on the heater Keep these instructions even once you have installed your heater 1 Where to install your heater This equipment was designed to be installed in a residence Please ask your distributor before using it for any other2. e more than 24 hours a Set the switch on 5 The heating indicator V1 This light comes on when the heating element is working It may flash when the temperature has stabilised 6 Locking the controls O It is possible to lock or limit use of the control dial and lock the switch to prevent unauthorised manipulation of the panel heater children etc a Unhook the panel heater from its wall mounting b Remove the pins P on the back of the thermostat casing C Select position B to lock the control dial or position L to limit the amount it can be turned Position M blocks the switch for Electronic Model 7 Using the pilot wire The product with pilot wire can receive the following signals from a master unit comfort temperature of control dial eco comfort temperature 3 C to 4 C frost free approximately 7 C off Put the switch to the programming mode The product must be connected through the pilot wire to a programming control or a product equipped with pass program system in order to use these different modes You can control several convectors with a single programmer or a product equipped with pass program system Warning When the programme turns to Frost Free or Off in the main programming system or using a Pass Program system these functions will override the manual switch of the Panel Heater 8 Using the On Off PassProgram system Ref 602019 When using programming mode c
3. keep children from playing with the device Do not introduce objects or paper into the device Do not totally or partially block the grilles on the front or inside ofthe appliance as this may cause overheating If the supply cord is damaged it must be replaced by a service agent or similarly qualified person in order to avoid a hazard applies to all units All work to the inside of the appliance must be carried out by a licensed electrician MAINTENANCE To maintain performances of your unit you should clean the upper and lower grilles of the unit about twice a year using a vacuum cleaner or a brush Have a professional check the inside of the unit every five years Dirt may collect on the grille of the unit if the atmosphere is polluted This phenomenon is due to the poor quality of the ambient air In this case it is recommended to check that the room is well ventilated ventilation air inlet etc and that the airis clean The unit will not be replaced under the guarantee because of this type of dirt The unit casing should be cleaned with a damp cloth never use abrasive products TROUBLE SHOOTING If the unit does not heat Check that the programmer is in COMFORT mode electronical Make sure that the installation circuit breakers are switched on or that the load shedder if you have one has not switched off the unit power supply Check the air temperature in the room The unit does not carry out programming orders v
4. purpose The panel heater should be installed according to normal trade practice and in compliance with legislation in the relevant country the IEE Wiring Regulations The device is to be installed so that switches and other controls cannot be touched by a person in the bath or shower except in the UK where IEE Regulations 701 512 2 and 701 512 3 apply These allow the use of IP24 rated products and their integral controls in Zone 2 and outside zones Comply with the minimum clearance distances for positioning of the panel heater If your wall covering is laid on foam a spacer the same thickness as the foam must be placed under the panel heater s support This ensures there is free space behind the panel heater to make sure its control settings are not adversely affected Do not install the panel heater 2 In a draught likely to affect the control settings under a fan etc 2 Under a fixed mains power socket In volume 1 of bathrooms It is strongly recomended not to install vertical products we manufacture above an altitude of 1000 metres If the device is installed at altitude the air discharge temperature will be increased by approximately 10 C per 1000 m of altitude It is forbiden to install vertical product in horizontal position 2 How to install the panel heater 2 1 Release the appliance s hook on bracket We recommend that you place the radiant panel flat face down Have a straight head screw
5. HE PANEL HEATER 1 Description of the control unit gt Mode cursor gt Temperature adjustment control dial V1 gt Heating indicator light 2 Fixing the comfort temperature Xt The comfort setting is the temperature that is preferred during times the rooms is occupied a Slide the switch cursor to 2 b Ajust the control dial to the preferred position the heating light V1 indicates if the temperature drops below the preferred on the control dial C Wait a few hours for the temperature to stabilise d If the setting is satisfactory if necessary use a thermometer to check mark the position for future use e If the setting is not satisfactory adjust it and start again from point c 3 Fixing the Eco temperature The Eco setting reduces the temperature setting by 3 to 4 degrees The Eco setting can be used when the room is unoc cupied for more than 2 hours a Slide the switch to b Adjust the control dial to the preferred position the heating light V1 indicates if the temperature drops below the temperature set on the control dial C Wait a few hours until the temperature stabilizes Note When switching n 1 on the picture is set on Programming system clock symbol with the PassProgram On Off please refer to paragraph n 8 4 Frost Free mode E This mode is used to keep the temperature at approximately 7 C in the room when you are absent from the house for a prolonged period i
6. driver to hand 2 2 Fix the hook on bracket to wall Drilling points A Drilling points B Note Do not use the device in mobile or feets or on casters except the range kit feet ref 417010 417015 417020 and Australian feet amp castor 572000 2 3 Connecting the panel heater The panel heater must be powered with 220 240V 50Hz The panel heater must be connected to the mains either by a 2 wire cable Brown Phase Blue Neutral via a power socket In humid areas such as bathrooms and kitchens the power socket must be installed at least 25 cm above the floor The installation must be equipped with a omnipole disconnection mechanism with a break contact distance of at least 3mm Earthing is prohibited Do not connect the pilot wire black to earth The heater must be installed by a qualified electrician in accordance with the local regulations The heater and the pilot wire black must NOT be connected to earth If the heater wire is damaged it must be replaced by a qualified person to avoid hazard If a pilot or piloted panel heater is protected by 30mA differential e g bathroom the pilot wire s power must be protected on this differential Complete N gative Positive Panel heater cable u No current alternation half alternation half alternation 230 V 115 V 115 V Mou AR Elect oi Oscilloscopes ON MN R f Neutral Do I P brown EA Phase Mode obtained COMFORT pese cci Al USING T
7. ersion with pilot wire Make sure that the programming unit is being correctly used refer to its user s manual or that the Chronopass is properly inserted in its housing and that it is operating normally batteries The unit is permanently heating Make sure that it is not in a draft and that the temperature setting has not been changed This unit with electronic control is equipped with a microprocessor that can be distribued by some severe mains voltage distur bances outside EC standards defining the disturbance protection level If there are any problems thermostat blocked etc switch off the unit power supply fuse circuit breaker etc for about 5 minutes to allow the unit to start again WARRANTY CONDITIONS KEEP THIS DOCUMENT IN A SAFE PLACE This certificate should only be produced if you are making a complaint attached with the invoice of the purchase This guarantee is applicable for 7 years from the date of original purchase Your Atlantic distributor will exchange parts shown to be defective in manufacture The replacement parts will be of charge but Atlantic does not accept responsability for freight or labor charges or losses in transit This guarantee excludes damage by neglect shipping or accident and any damage due to incorrect installation use or purposes other than those intended or failure to observe the instructions Atlantic Australasia Pty Ltd reserves the right to reject any warranty claims used in cond
8. itions other than domestic purposes or connected to non Australasia and New Zealand approved power boards extension leads double adaptors and power outlets UNIT TYPE SERIAL NUMBER CUSTOMER S NAME AND ADRESS This information is shown on the plate which can be seen on the left side or behind the front grille of the unit FOR SALES IN NEW ZEALAND INSTALLER S STAMP ATLANTIC AUSTRALASIA Phone 0800 422 000 Fax 04 38 00 509 Web www atlantics co nz Email sales atlantics co nz FOR SALES IN AUSTRALIA ATLANTIC AUSTRALIA Pty Ltd 4 13 25 Church Street Hawthorn Victoria Street Australia Free call 18 00 67 78 57 Phone 03 98 52 95 99 Fax 03 98 52 98 44 Web www atlantics com au Email sales atlantics com au web www atlantics com au O c81 L 08 cI
9. lock symbol with the on off pass program system interface timer the moon symbol on the timer refers to the off mode no heating Important If the timer 602019 is set to off this function will override the slide switch 1 modes eco comfort amp frost free on the heater RECOMMENDATIONS FOR USE There is no point in setting maximum heating the room temperature will not rise any quicker When you air the room disconnect the panel heater by putting the switch to off If you leave the room for several hours slide the switch to C eco position Absence for less than 2 hours set the cursor switch knob to moon 2 to 24 hours either you can lower the control dial by two graduations select eco mode or switch to off f you have several units in a room let them operate simultaneously This will give you a more uniform temperature without increasing electricity consumption Children must not lean on the appliance Under certain circumstances there is a risk that its surface may cause burns to the skin of young children If there is any risk of this at all install a protection grill This device is not intended for use by persons including children with physical sensory or mental disability or by persons lacking experience or knowledge unless they have received from a person in charge of their safety adequate supervision or preliminary instructions on how to use the device Care must be taken at all times to
Download Pdf Manuals
Related Search