Twin-tub Washing Machine User`s manual
Contents
1. Soft item e Embed the drain hose into the groove along the side of the spin tub in the order of heading for the side of the spin tub See to Figure 3 e Embed the drain hose into the groove with hands Take care not to damage the drain aw hose in fastening the fixing clamp spin tub side Insert the water inlet hose into the water filling entrance on the control panel To faa oE dismantle the water inlet pipe just push the control handle as indicated in the figure and pull it out Water fillin Water inlet hose begs Select water level according to the Wo quantity of the laundries Set the water level adjusting lever J Water level to needed line ES indicator Maximum gt Medium p 24 Minimum Mi gt Ie Preparation before washing Preparation before washing 1 Connect the water inlet hose 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle Do not connect the earth terminal to the gas pipe and tap water pipe 3 Put down the drain hose 4 Slanting or uneven ground may result in unstable working or abnormal noise Please make the machine stand horizontally Check if The quantity of When the pulsator the laundries ct se PA the laundries is running the has special out the coins the buttons Shall notbe too buttons of the requirement sand hairpin close zippers large Stretch lau2. Direct dissolved in the machine 1 Fill small quantity of water 2 Add the powder Runfor 30 seconds to dissolve it completely 3 Put it in the laundries Select suitable water level Fill water to decided level Dilute the whitener with container Pour it slowly into the washing tub Avoid using whitener on laun dries with color or pattern as they e f F are prone to lose color The instant dissolving of the washing powder 1 Prepare warm water of 30C and a container 2 Add the powder while stirring to fully dissolve it The powder is more prone to pollute the laundries than the detergent Therefore please use it with proper quantity The whitener shall not touch the laundries directly Refer to the user s manual for the usage and quantity of the whitener For powder whitener please dissolveit before Using Dosage of different washing powder is different Please refer tothe instruction of the washing powder for the detail dosage Washing sequence Wash timer Function selector Drain switch Spin timer Soft t Not set the switch to To set to below 1 minute To set to below 2 minutes an eni DRAIN during washing ar deel A canas meh Standard current first set to 6 minutes then the service life of the timer turn it back FF STANDARD STANDARD T SOFT SOFT r DRAIN CALEFACTION HWM80 0626S HWM80 0626SH WASH TIMER FUNCTION SELECTOR DRAIN SWITCH SPIN TIMER Wash 1 Water
3. filling selector Set the water inlet selector at the WASH side Figure 1 Figure 1 Set the water level adjusting lever to needed line sennniiianere 2 Fill the water and add the dissolved washing powder to make the water level reach the preset position Figure 2 Run washing program for some time to stir and dissolve the powder completely SNOAD rane Page7 LS SOFT SOEN 3 Put in the laundries If the water quantity is vate insufficient please add water Figure 3 4 Select the current HWM80 0626S HWM80 0626SH Select the strength of the current according to FUNCTION SELECTOR the laundries Figure 3 yi 15 T 3 5 Select the washing time N Figure 4 Select the washing time according to the laundries Figure 2 Figure 4 WASH TIMER 6 After washing set the WASH SELECTOR at DRAIN Figure 5 DRAIN Figure 5 DRAIN SWITCH Calefaction Function selector Soft current Standard current STANDARD CALEFACTION Figure 6 HWM80 0626SH FUNCTION SELECTOR When filling water to MAX or MED and MIN water levels turn the SELECTOR to the CALEFACTION after put in the laundries It begins to heat after close the wash tub when the temperature reaches 45 5 the Buzzer will give an musical alarm Then turn the selector to STANDARD or SOFT the heater will stop heating and the Buzzer will stop alarming It begins to wash after turning the WASH TIMER Remarks Don not open
4. rinsing When the laundries quantity is below 4 0 kg please use SOFT current lf you use STANDARD current it may splash 11 Spinning 1 Put the laundries into the spin tub evenly and smoothly 2 Press the gland in the tub properly Close the inner and outer cover of the spin tub 3 Spin Select suitable spin time according to the laundries and do spinning e During spinning if there is abnormal sound it is generally owing to slanting placement of the laundries Please stop the machine and reorder the laundries In spinning it will pause the work if you open the outer cover of the spin tub Close it to resume the spinning B To do spinning and draining and rinse oo with water filling together please first do spinning for around 1 minute then do draining or rinse with water filling Otherwise the spinning will stop owing to too much water stored in the spin tub 12 Disposal after washing e After using please clean the lint and foreign materials of the lint filter and overflow filter in time Otherwise it may influence your using the machine Please first pull off the power plug from the receptacle before cleaning Cleaning the lint filter The lint filter must be used during washing it must be cleaned in time after each using 1 Press the elastic piece at upper end of lint filter to release the tab from the filter cover and pull the lint filter ou
5. Twin tub Washing Machine User s manual This manual is for HWM80 0626S HWM80 0626SH e Please read this manual carefully before using e Retain it for future reference 0030807884 Contents names of the parts i Seed drat aca acuta ca egal sealer aia cara rae Safety precautions tettetett rtre errre Installation and adjustment srrrrrrrrrsss Preparation before washing tt ttt The musts in washing ee ee ee ee Usage of the detergent E E Genwen whe ae Washing SEQUENCE st ttt treet eee Disposal after washing ee EERE EEEE EERE EEN Trouble Shooting Answer to question Co list Specification s ttt tttt Names of the parts Wash tub cover Drain selector Program selector Wash timer Control panel seat Water filling entrance Control panel ___ Plate support left Water filling control handle Bypass channel Water level adjust lever Overflow filter Lint filter Drain hose Cabinet handle Wash tub Cabinet Base frame Ana Outer cover of the spin tub Inner cover of the spin tub ___ Spin timer Plate support right Spin tub frame Spin tub Front door Power cord Notes All illustrations in this Manual are given for reference only Your products and accessories may show differences from these illustrations due to our continuous impr
6. actory inspection of performance 16 Packing list S Name Quantity User s manual e One piece Warranty card One piece Water inlet hose i Se One piece Gland One piece Twin tub washing machine J One set Mee a Specification ae Water level Water a quantity about L Maximum 71 Medium 60 Minimum 49 Injection pressure MPa 0 02 0 2 Rated washing spinning 8 0 6 0 capacity kg pans iia TR 4 17
7. cians of our special shop or the after sale service department Do not put the machine at damp E place like the bathroom Never wash Do not use water hotter than 50 C it with water Do not place wet laundries y on the control panel In case the washing machine is installed Do not wash water proof laundries like on ground with carpet do not block the the raincoat bike covers etc to avoid ventilation hole with carpet abnormal vibrations in spinning oS a 2 fee Ventilation hole at eed REF the bottom of the Fl cette a washing machine Do not let the machine share one receptacle with other electric appliances If the power plug is damaged or the plugging into the receptacle is loose do not use the plug any more Safety precautions Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not decompose repair or alter the machine by yourself Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials such as thinner petrol etc Handicapped or children without care shall not use the machine Keep the machine away from direct sunlight and heat source like the 7 Please keep the lint filter in good condition and install it to pr
8. eezing Drain completely after using When the water is frozen Pour hot water below 50 C into the wash tub to soak it completely Then turn the pulsator with hands gently Please confirm the drainage can work normally before next using 15 Trouble shooting Answers to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do not repair it by yourself Phenomena The machine does not act The reason Is there power failure Is the power plug loose Is the pulsator twisted by foreign materials The draining does not work Does the drain hose put down Is the drain hose frozen Is the drain hose blocked by foreign material Are there laundries falling to the outer side of the spin tub There s abnormal sound during washing Are there hair pin coins or metal items brought inside the tub There s abnormal sound and violent vibration during spinning Is the machine slanting Is the gland pressed evenly Are there laundries falling to the outer side of the spin tub Are the laundries in spin tub too much There may be some waterflowing out of the drain hose in the first use of the machine It is the water remained in the f
9. hing dismount the water inlet hose Do not store water in the tub for long period Discharge the water immediately after each using Pull off the power plug and hang up the power cord Hang up the drain hose Wipe off the water drops on the surface and inside the tub with clean soft cloth Open the cover of the wash tub and the inner outer cover of the spin tub for some time about one hour then close them 14 Corrugation Trouble shooting Answers to question If the laundries fall to the outer side of the spin tub If the laundries fall to the outer side of the spin tub Please take it out quickly 1 Dismantle First take two plugs out then dismantle the two screws which fixed the Spin tub frame As Spin tub frame indicated in the figure push the point marked with X to pull the spin tub frame to oblique upwards to dismantle it Figure 1 Spin tu Please check carefully The laundries may fall to the lower part of the outer side of the spin tub Figure 2 e f the laundries fall to the outer side of the spin tub during spinning the draining will get blocked and the rotation speed of the spin tub is reduced Figure 2 Laundries 2 Install After install the back edge of the spin tub frame to proper position push the four points marked with X by force to reset it fix it with screws then fixed the two plugs at the position Figure 3 When the remained water is frozen Prevent the fr
10. ndries may on washing etc Jand loosenthe cause noise For laundries before the sake of putting themin discretion please the tub put the laundries with buttons into other laundries RR LE lt a S S a Check if the laundres are applicable for washing with machine b Divide the laundries that are not colorfast from other laundries c Put those laundries difficult to absorb water into water with hand d For those laundries with heavy sail please first remove the dirt like mud or dust For the pats with heavy soil please apply detergent on them in advance which can make it easier to remove the soil e For those laundries that may get lint ball and thee with long fur turn it over before putting in f Do not put those laundtes polluted by chemicals into the washing machine directly The musts in washing e The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time The thickness size type of the cloth will influ ence the actual washing capacity Itis suit able to put in reasonable amount of laundries and the laundries can be turned round in wash ing for one time washing e t issuggested to use foamless washing powder e Do not select Max water level for laundries less 1 5kg so as to avoid splashing of water Usage of the detergent How taco thocunitonee How to use the washing powder
11. oper position during washing If the lint filter is lost or damaged please contact the local after sale service department of our company Dismantl install Installation and adjustment Please install and adjust the machine according to the requirement of the manual It is very important to your security and correct operating the machine Usage of the drain hose The drain hose shall drain smoothly 1 The height of the drain hose shall be less than 10cm or the drainage will not be smooth and cost such long time that the machine may stop at mid way 2 Do not ramp or press the drain hose 3 If the drain hose is too long cut it at mid point To make smooth drainage cut the front end of the hose slantingly 4 If extra drain hose is needed please make separate purchase The inner diameter of the extra hose shall not less than 40mm and the length shall not exceed 1 5m If the extra hose is too long cut it either atAor atB point How to change the direction of the drain hoses e Figure 1 indicates the ex factory installation position of the drain hose Back RAN aa Extend the drain hose from the side of spin tub e Put soft items on the ground Lean the machine Figure 1 down gently with the front surface facing the ground Take off the drain hose from the cabinet Dismantle the drain hose fixing clamp and take the hose out of the fixing groove See to Figure 2 Front Cee
12. ovement Meaning and description of the symbols Contents marked with that symbol are related to the safety of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may cause damage of the machine or injure the personal safety of the user Warning sign Forbidding sign Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the personal safety of he user Please check if the power receptacle has good earthing condition before using to guarantee your safety Safety precautions Please insert the power cord into special When the machine is normally using receptacle with rated voltage Be sure to please put the power plug at the use single phase three pins receptacle location easily to be inserted and The earthing terminal of the receptacle extracted by hand Be sure to pull the must be earthed reliably If possible plug off when there s power failure or please adopt electric leakage protector the machine is being moved cleaned D or when it is idle 1 Do not bend extend twist bind by force Do not press or nip it with weight Keep the pin of the power plug clean if the power plug is polluted with dust please wipe with dry cloth carefully e f the power cord or the power plug is bad to avoid risk it is required to have it replaced by the techni
13. the wash tub when heating otherwise it will stop heating and influence the heating time Midway spinning 1 Put the laundries into the spin tub evenly and smoothly 2 Spin 1 Put the gland in properly Please put in the gland properly even if the laundries quantity is small Push Gland ol S 5 x Proper The laundries Proper No gland are slanting 2 Close the inner and outer cover of the spin tub Outer cover o The spin tub Inner cover 3 Spin for 1 2 minutes The spin tub 3 Run the foam removing spinning 1 Set the inlet selector handle on spin side and fill water for about 1 min e Incase water flows out from wash tub side due to too much inflow please turn down the water tap a bit 2 Close the spin tub outer cover and spin for about 1 2 min 10 Rinsing Rinse with water filling 1 Put the laundries into the wash tub Select suitable current according to the laundries 2 Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity Then fill suitable water continuously 3 Rinse Adjust the wash timer to 5 7 minutes to do rinsing Repeat the midway spinning and rinsing with stored water for 2 3 times Rinse with stored water 1 Put the laundries into the wash tub Select suitable current according to the laundries 2 Fill water to preset water level 3 Rinse Adjust the wash timer to 2 3 minutes to do
14. tward to remove it See Figure 7 Figure 7 2 Remove lint Pull the lower end of lint filter rear cover outward to disassemble it from the lint filter front cover Lint filter rear cover Remove lint completely with clear water See amp S Figure 8 Disassemble 3 Install lint filter Lint filter frontcover Pae Figure 8 Cleaning the overflow filter e Too much lint on the overflow filter will influence the normal usage of the machine Please clean it every two months 1 Take off the overflow filter Elastic fixing As indicated in the figure nip the elastic fixing claw and pull it to the direction of the arrow to take it off 13 Cleaning the overflow filter 2 Take off the corrugation pipe Dismantle the upper part of the corrugation pipe inside the overflow filter as indicated in Figure 9 Cleaning the overflow filter Clean the lint around the filter and flush with tap water Install the overflow filter 1 Install the corrugation pipe 2 Insert the mounting plate at the bottom of the filter into the valve cover 3 Hang up the hook at the left upper side 4 Push the upper part in as indicated in Figure 10 Water level adjusting lever gt ipe Figure 9 Figure 10 Disposal of the complete unit e Wipe the complete unit with soft cloth twisted dry Wipe with neutral detergent if too dirty Do not wash it directly by water After was
Download Pdf Manuals
Related Search