User Manual
Contents
1. 20mm 25mm 230mm Adjustment after Install Long Arm to wall 6 degrees 8 degrees Adjustment after Install Common to both 8 degrees Withstand Load Vertical 70Kof Non damaged or deformed Horizontal 2G Mild Steel CR4 Colour Sinterflex Black Safety Standards UL60950 CD CD CD lt X lt XIN ITIN lt NNN M The Unit is shipped with either S0001 Short Arm or L0001 Long Arm WALL MOUNTING KIT A1MOUNTSOO1 A1MOUNTLOO1 User Manual v uniAlapr082. Arm A using suitable masonry plugs or other reliable fixings to ensure safe installation Consult your builder or architect if in doubt If power cables are to be hidden behind the Wall Plate ensure there is enough room for them to enter into the Wall Arm channel unimpeded Cable aperture 3 If cables will be routed from below feed all cables up through the aperture in A ensuring there is sufficient to reach the connectors on the projector For top or bottom cable entry feed all cables through cover plate B Slide cover plate B on to the arm ensuring that the retaining plate C is under the arm runners 4 Fit mount E to projector using the 4 screws provided Slots are provided to centre projector Mounting Slots 5 Lift Projector and mount slide mount along the wall arm so that the retaining plate G is under the arm runners with mount cross member F above arm runners Tighten the 2 screws J 6 Cable up the projector ensuring there are no tight radii in the cables 7 Fit Wall Plate cover B and secure using fixing screw H into retaining bracket 8 Refer to Chart 1 and dependant on the required diagonal size of image adjust the distance from the face of the Whiteboard to the front of the projector nearest part to screen to the dimension in Chart 1 column ii by undoing the 2 screws J and sliding the projector mount along the wall arm A 9 FOCUS adjustment Roughly adjust the focus to match the sc
3. projector it may cause a malfunction Ensure that the projector is installed at a location where such direct light does not hit it e For any overhead installation please take extra safety precautions Check The Contents The A1 Mount assembly is in 2 parts Wall Arm 1 and Projector Mount 2 There are 2 versions of arm long or short The parts are shown below Also included are M6x8 Screws 4 pcs for fixing mount to projector and 1x4mm hex key and 1x5mm hex key Parts Fixing Guide H to M are screws for fixing together the above parts 1 Screen Diagram 1 nena i cm ii cm 60 00 3434 9 62 77 00 4060 2248 __ 1__ Top of Image Wall Arm lt I An _ WARNING Improper installation can result in serious personal injury Make sure that the structure can support a redundant weight factor five times the total weight of the equipment if not reinforce the structure before installing this equipment Installation 1 Mark the position on the wall for the wall arm plate A as shown in Diagram 1 The left edge of the wall plate should be 2 1cm to the right of the centre line of the image when facing the image To find dimension T the distance to the top of the wall plate select the required image size in diagonal inches from the left column of Chart 1 and use the corresponding dimension in cm from column 1 2 Fix the Wall
4. WALL MOUNTING KIT A1MOUNTSOO1 AIMOUNTLOO1 User Manual Contents Warnings Warning for dealers and installers 1 Cautions Check The Contents inert dineedudaeeedeveawateudesadwecs MEN m Technical SPCCINCAUION eps Va vu qr px Ou scu idet o Sup o Warnings Use this product only for the CP A100 ED A100 and ED A110 projectors Using with other projectors may be hazardous Before using this product be sure to read this manual and the safety and users manual for the projector Heed all the warnings in the manuals or on the product Follow the instructions and retain the manuals in a safe place for future reference Professional knowledge is required to to mount the projector with this kit Do not fit yourself Consult with your dealer or professional installer to be sure that it is installed correctly and safely The manufacturer assumes no responsibility for any damage caused by mishandling or misuse of this product Warning for dealers and installers For safety reasons pay attention to mechanical strength of the place where the projector is going to be installed with this kit Before installation ensure that the wall has sufficient strength to hold the projector and mounting kit Be sure that all metals and screws mentioned in this manual are fixed properly Do not modify any items in the kit To prevent an electrica
5. l shock or a fire do not install the projector while it is connected to a power supply Improper installation can result in serious personal injury Make sure that the structure can support a redundant weight factor five times the total weight of the projector If not reinforce structure before installation Always seek professional advice if unsure To ensure safety be sure to tighten screws and bolts securely Also be sure to use ONLY the items supplied Failure to do so may result in the projector falling and causing injury Cautions e Do not block the vents on the projector Do not place anything that can stick to the intake vents around the projector e following must be considered before the installation otherwise the temperature of inside of the projector may rise which may cause malfunction of the projector The ambient temperature range 0 35C Keep 30cm space from other objects around the projector to ensure proper ventilation of the projector Do not mount the projector near an air conditioner or something similar where the temperature is constantly changing e Do not place the projector in smoky dusty or humid place this may cause a fire electrical shock or malfunction of the projector e The air filter of the projector is required to be clean periodically the projector should be fixed at the place where it can be accessed e If strong sun light or fluorescent light hits the remote receiver or
6. reen size after mounting the projector in the correct position on the boom The image size and shape vary with the focus adjustment so it is vital to carry out this step before final adjustment 10 Adjust the projected image to size smaller than the actual screen size by moving the projector towards or away from the screen keeping the margins for all sides of the screen as shown in the table below Screen l Screen Size Vertical Horizontal inch margin mm margin mm Projected Image Vertical Margin Horizontal Margin l 11 If necessary re adjust the focus after the adjustment of the projected image size and position Go back to Step 10 if the image size goes over the margins after the focus fine tuning 12 PAN adjustment Adjust the Pan horizontal rotation 6Y of the projector Tighten screws J after adjustment 13 TILT adjustment Loosen the 2 screws on the side of the mount E Adjust the hand wheels L on either side of the mount cross member F to alter the side to side tilt 2 Now adjust the fore and aft tilt and hand tighten screws K to complete adjustment 14 Fit Projector mount cover D using fixing screw M to complete installation Technical Specification MOUNT SPECIFICATION Mount Fixing VESA 200x200 M6x8amm Range of Arm movement 25mm Short Arm to wall 280mm Range of Arm movement 2bmm Long Arm to wall 490mm Adjustment after Install 20mm Short Arm to wall 25mm 230mm
Download Pdf Manuals
Related Search