Home

XENYX 502/802/1002/1202

1. with a separate invoice for freight and packing Such costs will also be invoiced separately when the buyer has sent in a written repair order 6 WARRANTY TRANSFERABILITY This warranty is extended exclusively to the original buyer customer of retail dealer and is not transferable to anyone who may subsequently purchase this product No other person retail dealer etc shall be entitled to give any warranty promise on behalf of BEHRINGER 7 CLAIM FOR DAMAGES Failure of BEHRINGER to provide proper warranty service shall not entitle the buyer to claim consequential damages In no event shall the liability of BEHRINGER exceed the invoiced value of the product Customers in the European Union please contact BEHRINGER Germany Support for further details Technical specifications and appearance subject to change without notice The information contained herein is correct at the time of printing The names of companies institutions or publications pictured or mentioned and their respective logos are registered trademarks of their respective owners Their use neither constitutes a claim of the trademarks by BEHRINGER nor affiliation of the trademark owners with BEHRINGER BEHRINGER accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description photograph or statement contained herein Colours and specification may vary slightly from product Products are sold through
2. as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over LALI Rugg 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 CAUTION These service instructions are for use by qualified se
3. legally effective purchase contract 2 The warranty regulations mentioned herein are applicable unless they constitute an infringement of national warranty law 2 ONLINE REGISTRATION Please do remember to register your new BEHRINGER equipment right after your purchase by visiting www behringer com alternatively www behringer de and kindly read the terms and conditions of our warranty carefully Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently Thank you for your cooperation 3 WARRANTY 1 BEHRINGER BEHRINGER International GmbH including all BEHRINGER subsidiaries listed on the enclosed page except BEHRINGER Japan warrants the mechanical and electronic components of this product to be free of defects in material and workmanship for a period of one 1 year from the original date of purchase in accordance with the warranty regulations described below If the product shows any defects within the specified warranty period that are not excluded from this warranty as described under 5 BEHRINGER shall at its discretion either replace or repair the product using suitable new or reconditioned parts In the case that other parts are used which constitute an improvement BEHRINGER may at its discretion charge the customer for the additional cost of these parts 2 If the warranty claim proves to be justified the product will be returned to the user freight pr
4. our authorised dealers only Distributors and dealers are not agents of BEHRINGER and have absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying and recording of any kind for any purpose without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH BEHRINGER is a registered trademark ALL RIGHTS RESERVED 2006 BEHRINGER Spezielle Studiotechnik GmbH Hanns Martin Schleyer Str 36 38 47877 Willich Munchheide II Germany Tel 49 2154 9206 0 Fax 49 2154 9206 4903 5 WARRANTY 11
5. 10 Hz 200 kHz 3 dB 10 to 60 dB 12 dBu 10 dB gain approx 2 6 kQ balanced 110 dB 112 dB A weighted 0 dBu In 22 dB gain 0 005 0 004 A weighted 1 4 TRS connector electronically balanced approx 20 kQ balanced 10 kQ unbalanced 10 to 40 dB 22 dBu 0 dB Gain 90 dB 89 5 dB 89 dB 0 dB 1 dB 0 dB 3 dB 1 4 TRS connector electronically balanced approx 20 kQ 22 dBu 80 Hz 15 dB 2 5 kHz 15 dB 12 kHz 15 dB 80 Hz 15 dB 2 5 kHz 15 dB 12 kHz 15 dB 1 4 TS connector unbalanced approx 120 Q 22 dBu 1 4 TRS connector electronically balanced approx 20 KQ bal 10 KQ unbal 22 dBu Main outputs Type Impedance Max output level Control room outputs Type Impedance Max output level Headphones output Type Max output level Main mix system data Noise Main mix oo Channel fader o0 Main mix 0 dB Channel fader o Main Mix 0 dB Channel fader 0 dB Power supply Power consumption Mains voltage USA Canada 120 V U K Australia 240 V Europe 230 V Japan 100 V Dimensions 502 Dimensions H x W x D Weight net 802 Dimensions H x W x D Weight net 1002 Dimensions H x W x D Weight net 1202 Dimensions H x W x D Weight net Measuring conditions 1 4 TRS connector unbalanced approx 120 Q unbal 22 dBu 1 4 TS connector unbal approx 120 Q 22 dBu 1 4 TRS connector unbala
6. 4 connector Unbalanced devices mono jacks can also be connected to these inputs IS Please remember that you can only use either the microphone or the line input of a channel at any one time You can never use both simultaneously TRIM Use the TRIM control to adjust the input gain This control should always be turned fully counterclockwise whenever you connect or disconnect a signal source to one of the inputs 2 CONTROL ELEMENTS AND CONNECTORS 5 XENYX 502 802 1002 1202 2 1 2 Equalizer All mono input channels include a 3 band equalizer except for the 502 which is equipped with a 2 band EQ All bands provide boost or cut of up to 15 dB In the central position the equalizer is inactive The circuitry of the British EQs is based on the technology used in the best known top of the line consoles and providing a warm sound without any unwanted side effects The result are extremely musical equalizers which unlike simple equalizers cause no side effects such as phase shifting or bandwidth limitation even with extreme gain settings of 15 dB Fig 2 2 The equalizer of the mono input channels EQ The upper HI and the lower band LO are shelving filters that increase or decrease all frequencies above or below their cut off frequency The cut off frequencies of the upper and lower band are 12 kHz and 80 Hz respectively The mid band 802 1002 1202 is configured as a peak filter with a center frequency of 2 5 kHz L
7. 502 802 1002 1202 XENYX User s Manual Version 1 0 January 2006 E Gi BEHRINGER www behringer com JUST LISTEN XENYX 502 802 1002 1202 IMPORTANT SAFETY INSTRUCTIONS A To reduce the risk of electric shock do not remove the top cover or the rear section No user serviceable parts inside refer servicing to qualified personnel CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR A CAUTION WARNING To reduce the risk of fire or electric shock do not expose this appliance to rain and moisture The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus This symbol wherever it appears alerts you to the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock This symbol wherever it appears alerts you to important operating and maintenance instructions in the accompanying literature Please read the manual DETAILED SAFETY INSTRUCTIONS 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such
8. L ROOM PHONES switch if you want to monitor the 2 track input via the CTRL ROOM OUT This provides an easy way to monitor signals coming back from tape to ensure that they are recording correctly I amp If you are recording a signal via the CD TAPE OUTPUT and wish to listen to this simultaneously via the CD TAPE INPUT do not use the CD TAPE TO MIX switch Doing this would create a feedback loop since the signal would be routed via the main mix back to tape via the CD TAPE OUTPUT To monitor the CD TAPE INPUT use the CD TAPE TO CTRL ROOM switch to assign the tape signal to the monitor s or headphones This will avoid the tape signal being routed to the CD TAPE OUTPUT FX TO CTRL ROOM If you want to monitor only the FX send signal in your headphones or monitor speaker s press the FX TO CTRL switch This mutes the main mix signal while routing the FX SEND output to the monitor s The XENYX 802 and 502 do not feature this switch 2 3 5 Phantom power and LED displays A PHANTOM POWER 48V cur 1 20 R Fig 2 13 Phantom power and control LEDs 48 V 802 1002 1202 only The red 48 V LED lights up when phantom power is on The PHANTOM switch activates the phantom power supply on the XLR connectors of all mono channels IS Please do not connect microphones to the mixer or the stagebox wallbox as long as the phantom power supply is switched on Connect the micro phones before you s
9. LEVEL control determines the level of the channel signal in the main mix CLIP The CLIP LED s of the mono channels illuminate when the input signal is driven too high which could cause distortion If this happens use the TRIM control to reduce the preamp level until the LED does not light anymore 2 2 Stereo channels 2 2 1 Stereo line inputs LINE IN 2 3 Mono L Fig 2 4 Stereo line inputs LINE IN Each stereo channel has two balanced line level inputs on 1 4 jacks for left and right channels If only the jack marked L left is used the channel operates in mono The stereo channels are designed to handle typical line level signals Both inputs will also accept unbalanced jacks 2 2 2 Equalizer stereo channels 802 The XENYX 802 features a stereo 3 band EQ in each stereo channel The filter characteristics and cut off frequencies are the same as those in the mono channels Fig 2 5 The equalizer of the stereo input channels A stereo EQ is highly preferable to two mono equalizers when working on a stereo signal as two separate EQ s will usually produce an unwanted discrepancy between the left and right channels 2 2 3 FX sends balance and level adjustment Fig 2 6 The FX send balance level controls 6 2 CONTROL ELEMENTS AND CONNECTORS XENYX 502 802 1002 1202 FX The FX sends of the stereo channels function similar to those of the mono channels However since the FX send buses are
10. OW CUT In addition the mono channels 1002 and 1202 are equipped with a steep LOW CUT filter slope at 18 dB oct 3 dB at 75 Hz designed to eliminate unwanted low frequency signal components 2 1 3 FX sends panorama and level adjustment Fig 2 3 The FX send panorama evel controls FX 802 1002 1202 only FX sends or AUX sends enable you to feed signals via a variable control from one or more channels and sum these signals to a bus The bus appears at the console s FX send output and can be fed from there to an external effects device The return from the effects unit is then brought back into the console on the aux return connectors 802 or normal channel inputs Each FX send is mono and features up to 15 dB gain As the name suggests the FX sends of the XENYX mixing consoles are intended to drive effects devices reverb delay etc and are therefore configured post fader This means that the mix between dry signal and effect remains at the level determined by the channel s aux send irrespective of the channel fader setting If this were not the case the effects signal of the channel would remain audible even when the fader is lowered to zero PAN The PAN control determines the position of the channel signal within the stereo image This control features a constant power characteristic which means the signal is always maintained at a constant level irrespective of position in the stereo panorama LEVEL The
11. and the links between the controls we have arranged them in groups according to their function The illustrations at the beginning of each chapter show the controls described in each respective chapter IS The block diagram supplied with the mixing console gives you an overview of the connections between the inputs and outputs as well as the associated switches and controls For the moment just try and trace the signal path from the microphone input to the FX send connector Don t be put off by the huge range of possibilities it s easier than you think If you look at the overview of the controls at the same time you ll be able to quickly familiarize yourself with your mixing console and you ll soon be making the most of all its many possibilities If you need to know more about specific issues please visit our website at http www behringer com where you ll find explanations of for example effects and dynamics applications 1 3 Before you get started 1 3 1 Shipment Your mixing console was carefully packed in the factory to guarantee safe transport Nevertheless we recommend that you carefully examine the packaging and its contents for any signs of physical damage which may have occurred during transit IS If the unit is damaged please do NOT return it to us but notify your dealer and the shipping company immediately otherwise claims for damage or replacement may not be granted 1 3 2 Initial operation Be sur
12. both mono a mono sum is first taken from the stereo input before it is sent to the FX bus The 502 is not equipped with FXsends BAL The BAL ANCE control determines the levels of left and right input signals relative to each other before both signals are then routed to the main stereo mix bus If a channel is operated in mono via the left line input this control has the same function as the PAN control used in the mono channels LEVEL The LEVEL control determines the volume of the channel being sent to the main mix 4 10 The stereo inputs of the XENYX 1002 and 1202 have an input sensitivity switch which selects between 4 dBu and 10 dBV At 10 dBV home recording level the input is more sensitive requires less level to drive it than at 4 dBu studio level 2 3 Connector panel and main section 2 3 1 Send return effects path LEFT wono RIGHT 0 0 4 2 2 STEREO AUX RETURNS AUX SENDS MON OUT Fig 2 7 FX send return connectors on 0 5 AUX RETURN FX SEND XENYX1002 XENYX1202 Fig 2 8 FX send return controls STEREO AUX RETURN 802 only the STEREO AUX RETURN connectors are used to bring the output of the external effects device whose input is derived from the aux sends back into the console You can instead use these connectors as additional inputs but any effects device will then have to be brought back into the console via a normal stereo channel This does however give you the abi
13. chased Should your BEHRINGER dealer not be located in your vicinity you may directly contact one of our subsidiaries Corresponding contact information is included in the original equipment packaging Global Contact Information European Contact Information Should your country not be listed please contact the distributor nearest you A list of distributors can be found in the support area of our website www behringer com Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently Thank you for your cooperation 2 CONTROL ELEMENTS AND CONNECTORS This chapter describes the various control elements of your mixing console All controls switches and connectors will be discussed in detail 2 1 Mono channels 2 1 1 Microphone and line inputs Fig 2 1 Connectors and controls of mic line inputs MIC Each mono input channel offers a balanced microphone input via the XLR connector and also features switchable 48 V phantom power supply for condenser microphones The XENYX preamps provide undistorted and noise free gain as is typically known only from costly outboard preamps IS Please mute your playback system before you activate the phantom power supply to prevent switch on thumps being directed to your loudspeakers Please also note the instructions in chapter 2 3 5 Phantom power and LED displays LINE IN Each mono input also features a balanced line input on a 1
14. e that there is enough space around the unit for cooling purposes and to avoid over heating please do not place your mixing console on high temperature devices such as radiators or power amps The console is connected to the mains via the supplied cable The console meets the required safety standards Blown fuses must only be replaced by fuses of the same type and rating IS Never connect the XENYX to the power supply unit when the latter is connected to the mains First connect the power supply unit to the console then connect the power supply unit to the mains IS Please note that all units must be properly grounded For your own safety you should never remove any ground connectors from electrical devices or power cables or render them in operative IS Please ensure that only qualified people install and operate the mixing console During installation and operation the user must have sufficient electrical contact to earth otherwise electrostatic discharges might affect the operation of the unit 1 3 3 Online registration Please do remember to register your new BEHRINGER equipment right after your purchase by visiting www behringer com alternatively www behringer de and kindly read the terms and conditions of our warranty carefully Should your BEHRINGER product malfunction our goal is to have it repaired as quickly as possible To arrange for warranty service please contact the retailer from whom the equipment was pur
15. e tip strain relief clamp ground shield hot ve sleeve g ring ring cold ve UL For connection of balanced and unbalanced plugs ring and sleeve have to be bridged at the stereo plug Fig 3 3 1 4 stereo plug Headphones connection with 1 4 TRS connector sleeve tip strain relief clamp ground shield left signal sleeve S ring ring right signal DI Fig 3 4 Stereo plug for headphones connection 3 INSTALLATION 9 XENYX 502 802 1002 1202 4 SPECIFICATIONS Mono inputs Microphone inputs XENYX Mic Preamp Type XLR electronically balanced discrete input circuit Mic E 1 N 20 Hz 20 kHz 0 Q source resistance 50 source resistance 150 Q source resistance 134 dB 135 7 dB A weighted 131 dB 133 3 dB A weighted 129 dB 130 5 dB A weighted Frequency response Gain range Max input level Impedance Signal to noise ratio Distortion THD N Line input Type Impedance Gain range Max input level Fade out attenuation Crosstalk attenuation Main fader closed Channel muted Channel fader closed Frequency response Microphone input to main out lt 10 Hz 90 kHz lt 10 Hz 160 kHz Stereo inputs Type Impedance Max input level EQ mono channels Low Mid High EQ stereo channels Low Mid High Aux sends Type Impedance Max output level Stereo aux returns Type Impedance Max input level 10 lt 10 Hz 150 kHz 1 dB lt
16. epaid 3 Warranty claims other than those indicated above are expressly excluded 4 RETURN AUTHORIZATION NUMBER 1 To obtain warranty service the buyer or his authorized dealer must call BEHRINGER see enclosed list during normal business hours BEFORE returning the product All inquiries must be accompanied by a description of the problem BEHRINGER will then issue a return authorization number 2 Subsequently the product must be returned in its original shipping carton together with the return authorization number to the address indicated by BEHRINGER 3 Shipments without freight prepaid will not be accepted 5 WARRANTY REGULATIONS 1 Warranty services will be furnished only if the product is accompanied by a copy of the original retail dealer s invoice Any product deemed eligible for repair or replacement under the terms of this warranty will be repaired or replaced 2 If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level in any country which is not the country for which the product was originally developed and manufactured this modification adaptation shall not be considered a defect in materials or workmanship The warranty does not cover any such modification adaptation irrespective of whether it was carried out properly or not Under the terms of this warranty BEHRINGER shall not be held responsible for any cost resulti
17. er complies with all applicable safety standards IS Please use only the power supply unit provided with the console IS Never connect the XENYX to the power supply unit while the latter is connected to the mains First connect the console to the power supply unit then connect the power supply unit to the mains IS Please note that both the power supply unit and the mixing console heat up considerably during operation This is completely normal 3 2 Audio connections You will need a large number of cables for different applications The illustrations below show how the connectors should be wired Be sure to use only high grade cables Please use commercial RCA cables to connect the 2 track inputs and outputs You can of course also connect unbalanced devices to the balanced inputs outputs To do this use either mono plugs or stereo plugs with the ring and sleeve bridged pins 1 and 3 in the case of XLR connectors IS Caution Never use unbalanced XLR connectors PIN 1 and 3 connected on the MIC input connectors when using the phantom power supply Balanced use with XLR connectors 1 ground shield 2 hot ve 3 cold ve Input Output For unbalanced use pin 1 and pin 3 have to be bridged Fig 3 1 XLR connections Unbalanced use of 1 4 TS connector sleeve ground shield strain relief clamp sleeve tip 1 Lk Fig 3 2 1 4 mono plug Balanced use of 1 4 TRS connector sleev
18. f pushing the mixing consoles combining analog and digital technologies to their limits My vision was to enable you the user to give free rein to your true potential and creativity The result is mixing consoles that combine incredible performance with intuitive operability They cannot fail to impress with their extremely flexible routing possibilities plus a fantastic wealth of functions Innovative technologies such as the completely new XENYX Mic Preamps and the British EQs guarantee optimum sound quality And extraordinarily high quality components provide unrivalled reliability even under extreme loads Thanks to the quality and ease of use of your new XENYX mixing console you ll soon come to appreciate that both personally and in my capacity as musician and sound engineer put you the end user first and that these products were only possible because of the passion and the attention to detail that went into them Thank you for the confidence you have placed in us by purchasing the XENYX mixing console should also like to thank all those who with their personal commitment and passion have helped me create this impressive series of mixing consoles Kindest regards Uli Behringer 1 INTRODUCTION Congratulations In purchasing our XENYX 502 802 1002 1202 you have acquired a mixing console whose small size belies its incredible versatility and audio performance The XENYX Series represents a milestone in
19. lity to use the channel EQ on the effects return signal if you wish IS When using a stereo channel as effects return path the FX control of the relevant channel should generally be turned fully down to avoid undesirable feedback If only the left connector is used the AUX RETURN automatically operates in mono Use the AUX RETURN control to determine how much of the effects signal is sent to the main mix FX SEND The FX SEND output does not apply for 502 should be connected to the input of an external effects unit The post fader FX signal you created using the input channel FX controls is sent to the effects unit via the FX SEND ouput Use the FX SEND control of the main section to adjust the overall send level 1002 and 1202 only 2 CONTROL ELEMENTS AND CONNECTORS 2 3 2 Monitor and main mix BEHRINGER CTRL ROOM OUT MAIN OUT Fig 2 9 Monitor main mix connectors PHONES CONTROL ROOM 0 MAX MAIN SECTION Fig 2 10 Monitor control and main mix fader PHONES CONTROL ROOM The stereo PHONES jack at the top of the connector panel is where you connect headphones The unbalanced CTRL ROOM OUT jacks carry the summed effects and main mix signals as well as soloed channel signals The PHONES CONTROL ROOM control adjusts the level of both headphones and main monitor outputs The 502 is not equipped with control room outputs MAIN MIX The MAIN OUT connectors are unbalanced mono jacks The main
20. mix signal appears here at a level of O dBu The MAIN MIX fader adjusts the volume of these outputs The XENYX 802 and 502 mixing consoles feature a rotary control for this purpose 2 3 3 CD Tape connectors CD TAPE INPUT The CD TAPE INPUTs are used to bring an external signal source e g CD player tape deck etc into the console They can also be used as a standard stereo line input so the output of asecond XENYX or BEHRINGER ULTRALINK PRO MX882 can be connected CD TAPE INPUT OUTPUT Fig 2 11 CD Tape input output Alternatively the line or tape output of a hi fi amplifier with source selection switch could also be hooked up here allowing you to easily listen to additional sources XENYX 502 802 1002 1202 CD TAPE OUTPUT These connectors are wired in parallel with the MAIN OUT and carry the main mix signal unbalanced Connect the CD TAPE OUTPUT to the inputs of your recording device The output level is adjusted via the high precision MAIN MIX fader or rotary control 802 2 3 4 Signal assignment A CD TAPE TO CTRL A CD TAPE FX TO CTRL Fig 2 12 Assignment switches of the main section CD TAPE TO MIX When the TAPE TO MIX switch is depressed the 2 track input is assigned to the main mix providing an additional input for tape machines MIDI instruments or other signal sources that do not require any processing CD TAPE TO CTRL ROOM 502 CD TAPE TO PHONES Press the CD TAPE TO CTR
21. nced 19 dBu 150 Q 25 dBm 106 dB 109 dB A weighted 95 dB 98 dB A weighted 84 dB 87 dB A weighted 502 13 W 802 17 W 1002 18W 1202 23W 60 Hz MXUL5 adapter 50 Hz MXUK5 adapter 50 Hz MXEU5 adapter 60 Hz MXJP5 adapter 1 5 6 1 1 2 47 mm 37 mm x 5 1 4 134 mm x7 177 mm approx 0 55 kg 1 21 Ibs 1 5 6 1 1 2 47 mm 37 mm x 7 2 5 189 mm x 8 2 3 220 mm approx 1 00 kg 2 21 Ibs 1 5 6 1 1 2 47 mm 37 mm x 7 2 5 189 mm x 8 2 3 220 mm approx 1 05 kg 2 31 Ibs 1 5 6 1 1 2 47 mm 37 mm x 9 1 2 242 mm x 8 2 3 220 mm approx 1 35 kg 2 97 Ibs 1 1 kHz rel to O dBu 20 Hz 20 kHz line input main output unity gain 2 20 Hz 20kHz measured at main output Channels 1 4 unity gain EQ flat all channels on main mix channels 1 3 as far left as possible channels 2 4 as far right as possible Reference 6 dBu BEHRINGER is constantly striving to manintain the highest professional standards As a result of these efforts modifications may be made from time to time to existing products without prior notice Specifications and appearance may differ from those listed or illustrated 4 SPECIFICATIONS XENYX 502 802 1002 1202 5 WARRANTY 1 OTHER WARRANTY RIGHTS AND NATIONAL LAW 1 This warranty does not exclude or limit the buyer s statutory rights provided by national law in particular any such rights against the seller that arise from a
22. ng from such a modification adaptation 3 Free inspections and maintenance repair work are expressly excluded from this warranty in particular if caused by improper handling of the product by the user This also applies to defects caused by normal wear and tear in particular of faders crossfaders potentiometers keys buttons tubes guitar strings illuminants and similar parts 4 Damages defects caused by the following conditions are not covered by this warranty A improper handling neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals A connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used A damages defects caused by force majeure or any other condition that is beyond the control of BEHRINGER 5 Any repair or opening of the unit carried out by unauthorized personnel user included will void the warranty 6 If an inspection of the product by BEHRINGER shows that the defect in question is not covered by the warranty the inspection costs are payable by the customer 7 Products which do not meet the terms of this warranty will be repaired exclusively at the buyer s expense BEHRINGER will inform the buyer of any such circumstance If the buyer fails to submit a written repair order within 6 weeks after notification BEHRINGER will return the unit C O D
23. rvice personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions unless you are qualified to do so XENYX 502 802 1002 1202 TABLE OF CONTENTS 1 INTRODUC TION mocinno enaena aanerer areen eden E an aana aS aiiai 4 1 1 General mixing Console fUNCtIONS 20 2 0 eect ceeeeeeeceeeeceeeeeaeeceaeseaeeseeecaaeeeaeessaeeeaeeseeeseaeesieeseaeeesieeseeesieeseaeenaes 4 1 2 The USEF ETC 5 1 3 Before VOU GEL Stam EE 5 e Eller VE EE 5 132 Mtia OPS Fath EEN 5 1 3 3 ONIIME e E Ce EE 5 2 CONTROL ELEMENTS AND CONNECTORS ccccceeeeeeeeeeeeeeeeeeeeeeeeseeneneneeeeeeeeees 5 2 1 MONO ChANMEIS EE 5 2 11 Microphone anad BUCH 5 22 UE 6 2 1 3 FX sends panorama and level adjustment piipissnecnni a a a a e ened 6 2 2 Stereo CHAMMEIS ses ssacss deed cigdt naan noia asi eaa aaa a aaan E aiaia Ea Taia sunday N aE naa aari NRN ia 6 CN Stered El e 6 2 2 2 Equalizer stereo Channels 072 6 2 2 3 FX sends balance and level adjustment 0 cccccccccceeececeee cece eeceeeeeeeceeeeeeeeseeeaeeeeeseeeeeeeeeeeceeneeeeeess 6 2 3 Connector panel and main SECON 0 2 eee eet ceteeeeeeteeeceeeceaeesaeeceaeseaeeceeeceaeeeaeesaeseaeeseeseaeesseeeseaeesieeseateeaes 7 2 3 1 Send Peturn SSCS PAU EE 7 2 3 2 Monitor And MAIN MIX zeen eee eee eect erent teenie E apea aia nea seneee senate seneeseniteeseieeesiieeeeesenteeseneeseneeeee 7 KE RRE 7 KEE e EE 8 2 3 9 Phantom po
24. the development of mixing console technology With the new Xenyx microphone preamps including phantom power as an option balanced line inputs and a powerful effects section the mixing consoles in the XENYX Series are optimally equipped for live and studio applications Owing to state of the art circuitry your XENYX console produces a warm analog sound that is unrivalled With the addition of the latest digital technology these best in class consoles combine the advantages of both analog and digital technology The microphone channels feature high end XENYX Mic Preamps that compare well with costly outboard preamps in terms of sound quality and dynamics and boast the following features A 130dB dynamic range for an incredible amount of headroom A A bandwidth ranging from below 10 Hz to over 200 kHz for crystal clear reproduction of even the finest nuances A The extremely low noise and distortion free circuitry guarantees absolutely natural and transparent signal reproduction A They are perfectly matched to every conceivable microphone with up to 60 dB gain and 48 volt phantom power supply A They enable you to use the greatly extended dynamic range of your 24 bit 192 kKHz HD recorder to the full thereby maintaining optimal audio quality British EQ The equalizers used for the XENYX Series are based on the legendary circuitry of top notch consoles made in Britain which are renowned throughout the world for their incredibly
25. warm and musical sound character Even with extreme gain settings these equalizers ensure outstanding audio properties CAUTION IS We should like to draw your attention to the fact that extreme volumes may damage your hearing and or your headphones or loudspeakers Turn the MAIN MIX control and PHONES control in the main section fully counter clockwise before you switch on the unit Always be careful to set appropriate volume levels 1 1 General mixing console functions A mixing console fulfils three main functions A Signal processing Preamplification level adjustment mixing of effects frequency equalization A Signal distribution Summing of signals to the aux sends for effects processing and monitor mix distribution to one or several recording tracks power amp s control room and 2 track outputs A Mix Setting the volume level frequency distribution and positioning of the individual signals in the stereo field level control of the total mix to match the recording devices crossover power amplifier s All other mixer functions can be included in this main function The interface of BEHRINGER mixing consoles is optimized for these tasks enabling you to easily keep track of the signal path 4 1 INTRODUCTION XENYX 502 802 1002 1202 1 2 The user s manual The user s manual is designed to give you both an overview of the controls as well as detailed information on how to use them In order to help you underst
26. wer and LED diSplayS s icives gecscccze svceesscecvest cs eenaa E NAE ANRE rates 8 3 INSTALLATION ti tia eine edd ceed aE ap pipa a ipi api ESENE SSE 9 31 M ns leede EE 9 S AdO OO ET EE 9 4 SPECIFICATIONS E 10 5 WARRANTY E 11 XENYX 502 802 1002 1202 FOREWORD Dear Customer I m sure you re one of those people who have devoted themselves body and soul to your chosen area and no doubt this has made you an expert in your field Well for over 30 years my passion has been music and electronics This not only led me to establish BEHRINGER but also enabled me to share my enthusiasm with our employees During all the years I ve been involved with studio technology and end users have developed a feel for the things that really count such as sound quality reliability and ease of use What is more have always had the desire to test the boundaries of what is technically feasible It was precisely this motivation that prompted me to start work on a new series of mixing consoles Since our EURORACKs had already set new standards world wide knew the development objectives behind the next generation of mixing consoles had to be especially ambitious Thus the concept and design of the new XENYX mixing consoles bear my signature The design work the entire circuit diagram and PCB development and even the mechanical concepts are my own work carefully selected each individual component with the aim o
27. witch on the power supply In addition the monitor PA loudspeakers should be muted before you activate the phantom power supply After switching on wait approx one minute in order to allow system stabilization POWER The blue POWER LED indicates that the console is powered on LEVEL INDICATOR The high precision 4 segment display accurately displays the relevant signal level LEVEL SETTING To correctly set the gains of the channels first set the LEVEL controls of the input channels to their center positions 0 dB Then use the TRIM controls to increase the input amplification until signal peaks show 0 dB on the level meter When recording to digital recorders the recorders peak meter should not go into overload While analog recorders can be overloaded to some extent creating only a certain amount of distortion which is common and often desirable digital recorders distort quickly when overloaded In addition digital distortion is not only undesirable but also renders your recording completely useless IS The peak meters of your XENYX display the level virtually independent of frequency A recording level of 0 dB is recommended for all signal types 8 2 CONTROL ELEMENTS AND CONNECTORS XENYX 502 802 1002 1202 3 INSTALLATION 3 1 Mains connection AC POWERIN Connect the power supply to the 3 pin mains connector on the rear of the console Use the AC adapter supplied to connect the console to the mains The adapt

XENYX 502/802/1002/1202

Contents

Download Pdf Manuals

Related Search

Related Contents