FEMA ELECTRÓNICA
Contents
1. Menu options OPT1 OPT2 and OPT3 give access to the configuration menus of the installed options The menu de pends on the installed option If there is no option installed the instrument shows nonE Information Menu Configuration Conf Informs the configured input signal range 4 20mA 0 10Vdc and the values for input low ILo display low dLo input high Ihl and display high dhl Maximum MAX Value of the maximum display Minimum Min Value of the minimum display AlarmX ALX Configuration of alarm X The sequence of information shows if the alarm is being managed On Off IT and Instrumentation for industry When the instrument detects that the displayed value does not correspond to the expected value the display will flash and alternate with a message h udr Hardware underrange The instrument is reading the lowest possible signal and can not follow lower signals h oVr Hardware overrange The instrument is reading the highest possible signal and can not follow higher signals d udr Display underrange The instrument is displaying the minimum value 9999 and can not display below d oVr Display overrange The instrument is displaying the maximum value 9999 and can not display above hoLd The instrument is showing the value present when the hold function was activated Hold function is active Min The instru2. fixed digits recursive display filter password brightness control measure function visualizes input signal without scaling offset and signal high autocorrection assigns the actual signal to the low or high reading peak amp hold function and password Power options with universal AC and DC ranges and space for 2 additional control and or signal retransmission modules soon 3 modules For measurements in CAT II and for environments with de gree of pollution 1 and 2 without condensation Standard IP54 front protection with optional upgrade to IP65 protection Connections via plug in screw terminals and configuration via three front push buttons For application on industrial environments Order Reference Model Power Option1 Option2 Option3 Others M40 P H H_ 85 265 Vac dc R1 1 relay R1 1 relay Available soon 65 IP65 L 11 60 Vdc AO Analogue output AO Analogue output empty and 24 48 Vac empty empty Precautions on installation Risk of electrical shock Instrument terminals can be connected to dangerous voltage A mj CE This instrument has been designed and verified according to the 61010 1 CE security regulation and is designed for applications on industrial environ ments See the CE Declaration of Conformity further in this document for information on the categ
3. kept on hold Leaving the Information Menu returns to the measuring state of the instrument without restart Information Menu Tree See page 5 Rollback After 30 seconds without interaction from the operator the instrument leaves the Information Menu Button SQ Selects the visible option Button UP Moves vertically along the available menu op tions Button LE Leaves selected menu or leaves the nforma tion Menu Operating the Configuration Menu To enter the Configuration Menu press the SQ button The Configuration Menu allows to change the configuration of the instrument Access to the Configuration Menu can be password protected with the function PASSWord During operation with the Configuration Menu the alarms remain frozen and are kept on hold When leaving the Configura tion Menu the instrument performs a restart and new con figuration is applied During the restart of the instrument a short alarm deactivation is performed Configuration Menu Tree See page 6 Rollback After 30 seconds without interaction from the operator the instrument leaves the Configuration Menu discarding all changes Button SQ Moves horizontally on the menu Allows selec tion of the current option displayed During a value selection menu for example a setpoint value validates the value on display Button UP Moves vertically on the menu Disp
4. 0 1000 0 1000 0 10 Vdc 20mA 1000 10 Vdc 1000 Sales 44 0 1273 570 220 Website www amplicon com Email sales amplicon com Amplicon Datasheet Input Menu The input menu allows for selection of the input signal range Options are 4 20mA 0 10Vdc 20mA and 10Vdc Jumpers 4 Vdc or 5 mA at the rear of the instrument must be closed according to the range selected Otherwise the display will show erratical behavior Scaling Menu The display scaling is based on 4 parameters These param eters define the two points of the straight line signal display Input Low ILo Signal input low Display Low dLo Input High lhl Display High dhl Display low Signal input high Display high Hysteresis hySt Value from 0 to 9999 Points of hyster esis The hysteresis applies on the deactivation of the alarm Delay dEL Value from 0 0 to 99 9 seconds Delay to be applied to the relay activation and deactivation Relays are activated and deactivated X seconds after the activation deactivation of the alarm The delay affects only to the relays The delay does not affect to the front leds Setpoint2 SEt2 Value from 9999 to 9999 Second setpoint The second setpoint allows for the creation of acti vation windows If the alarm is configured as maximum with setpoint 1000 and setpoint2 is configured at 1500 the
5. Datasheet Panel meter 96x48mm for process signals 20mA and 10Vdc Panel meter for process signals in mA and Vdc Accepts both active and passive signals monopolar and bipolar from 2 and 3 wire transducers Housing 96x48mm DIN standard Display in 4 or 5 digits Provides excitation voltage for transducers Segment linearization maximum and minimum display memory scalable reading filters steps signal autocorrection measure function peak amp hold alarms with double setpoints 5 levels of brightness Universal AC and DC power modules and up to 3 modules for signal retransmission and control IT and Instrumentation for industry Amplicon Sales 44 0 1273 570 220 Website www amplicon com Email sales amplicon com Datasheet Meter M40 P Panel meter 96x48mm size for process signals Panel meter for process signals in mA and Vdc active and passive monopolar and bipolar from 2 or 3 wire transducers Provides 15V max 40mA excitation voltage to power up the transducer when needed Scalable reading 10 segment linearization Instrument with 96x48mm standard DIN size Resolution 4 digits plus negative sign 9999 or 5 digits with negative sign with last digit fixed to zero 99990 with menu function Right Zero Management for up to 4 alarms with 1 or 2 setpoints each with hysteresis and delays Provides memory for maximum and minimum left zeros display on selectable steps
6. On management a aF F Inactive Off Leter gt an With left zeros EYPE TAH Alarm as maximum Left Zeros EE 1 wanna hana d UE Alor eee PTE ceEr gt On _ Add zero xxxxo aE E HAAA Add Right Zero SEE ieee HY4SE HAAA Counts Hysteresis n A H A A A g Memory of maxim g E L A A Al Al Seconds Maximum C E 5 E Reset of maxim Delay E Zi yo GE Ee or FERE Ola AGG memory of minim Setpoint2 E F Second setpoint Minimum H a r E 5 E Reset of minim IT and Instrumentation for industry Amplicon Sales 44 0 1273 570 220 Website www amplicon com Email sales amplicon com Datasheet Configuration Menu cESE IT and Instrumentation for industry Reset z bet m PASS an Ada Password Select password OFF FAcE no Factory Defau
7. Vexc transducer available soon y y Signal Pa ans E e U I Active voltage signal 0 10Vdc 10Vdc sf 5 r 123 C 29 ia J 4 closed oo umper 4 close 12 3 8 9 0 45 Signal Voltage generator Signal Jumpers 45 Power Connon Power Connections Passive voltage signal 0 10Vdc 10Vdc 123 890 Jumper 4 closed lt 45 4 Vexc 3 Wire transducer T Signal s Common Earth connection Although a terminal is offered for earth connection the connection is optional The instrument does not need this connection for correct functioning nor for compliance with the security regulations Fuse To comply with security regulation 61010 1 add to the power line a protection fuse acting as disconnection element easily accessible to the operator and identified as a protection device Power H fuse 250mA time lag Power L fuse 400mA time lag IT and Instrumentation for industry Amplicon Sales 44 0 1273 570 220 Website www amplicon com Email sales amplicon com Datasheet Technical Data Technical Data cont Digits Type Height Display maximum Display minimum Decimal point Overrange Underrange Signals accepted Rang
8. alarm will be activated between 1000 and 1500 and the alarm will be deactivated when display is lt 1000 and gt 1500 Setpoint2 is affected on the same way as the setpoint with hysteresis and delays Display Menu Decimal Point Menu Select the position for the decimal point Modify with the LE button and validate with the SQ button Auto Correction Menu Assigns the current input signal value to the Input Low or Input High configuration parameters The new values for Input and Display are displayed Auto Low A Lo Select A Lo to set the current input signal value to the Input Low configuration parameter Auto High A hl Select A hl to set the current input signal value to the Input High configuration parameter AlarmX Menu The instrument manages up to 4 alarms Each alarm is controlled by the condition display higher or lower than the configured setpoint The front leds are controlled by the activation deactivation of the related alarm The relays installed on Option1 Option2 and Option3 are controlled by alarms 1 2 and 3 Active Act Value On Off Defines if the instrument has to manage this alarm or not Select Off for alarm not managed Type tyPE Value Max Min Defines the behavior of the alarm as maximum or minimum alarm The alarms config ured as maximum are activated when the display value is equal or higher than the setp
9. alue OptionX OptX Type of module installed If there is no module shows nonE Measure MEAS Multimeter function Shows the value of the input signal without scaling This is the real value the instrument is receiving on terminals in Vdc or mA Tools Menu Messages and errors Advanced Display Ad dl Segments linearization The instrument has 10 linearization segments 11 points Each linearization points is formed of a signal input value InPX and an associated display value dISPX Enter the values for each point from the Points menu PntS It is required that the input signal values InPX mustincrease for each new point When all points are entered select Act value to On in the activation menu A check is automatically performed when entering the points and when activating the points In case of error verify the data entered on the points Leave the menu pressing LE button Reset option rESt deletes all existing points Password Pass Select a number to act as password This password will be requested when entering the Configuration Menu To deactivate the password select Off Factory Settings Fact Factory default configuration Se lect yES to activate the factory default configuration Version Ver Firmware version installed Light Ligh Brightness Select between 5 predefined levels of brightness Options Menu
10. e soon MEAS HHAH misii Measure Volt mA IT and Instrumentation for industry Sales 44 0 1273 570 220 Website www amplicon com Email sales amplicon com Measured Value Amplicon Datasheet Configuration Menu J f Range 4 20mA oo P Ye Li g AH See menu for Alarm1 Input AIPA Li iLi Range 0 10Vdc m E A tom a See menu for Alarm1 am Range 20mA Cu g J r m See menu for Alarm1 h 5 l o Range 10Vdc pane d 15P Sec AL a i L on AHHE p Display Scaling Input Low F Hg E aa J Eee i a dla HAAAEL Fixed Digits EF Fix digits Display Low cit W TAL HBBE H E ee ee Input High ALl on gt AHBAB W JAI 886A meres oFF Display High d P l gt Q Al A g Press LE to change selection E E E P on Decimal Point Steps Acar ALa ABBAA gt HBBE E Auto correction Auto Low Signal Low Display Low 5 Ahi gt BAHH BABA Ia Auto High Signal High Display High an Z LI ALr al Alarms T A L r gt A c E on eee F F Counts for step Alarm1 Active
11. eneric rule of emission IT and Instrumentation for industry 40 10 cycle Criteria A 70 25 cycle Criteria B 0 250 cycle Criteria B Barber del Vall s September 2011 Daniel Junc Quality Manager Amplicon Sales 44 0 1273 570 220 Website www amplicon com Email sales amplicon com
12. es selectable Connections Types Input impedance Maximum input signal Oversignal Excitation voltage Accuracy at 25 C inmA in Vdc when using Vexc Acquisitions Display refresh Step response time Power Power H Power L Consumption Isolation Configuration Functions available Segment linearization Fixed digits Filter on display Steps Memory of maximum Memory of minimum Zeros to the left Add zero to the right Password Measure function Auto correction high Auto correction low Peak amp Hold Double setpoints Brightness control 4 or 5 with last digit fixed to zero 7 segments red 14mm 9999 99990 9999 99990 selectable 8 8 8 8 9999 flashing 9999 flashing mA Vdc 4 20mA 0 10Vdc 20mA 10Vdc 2 or 3 wire active or passive signals the instrument provides the exci tation voltage if needed 9 1R in mA 932K in Vdc 10 5Vdc 27mA max 100mA max 100Vdc 15Vdc 10 max 40mA protected against short circuit 0 05 F S 1 digit 0 05 F S 1 digit 0 25 FS total 0 30 in mA 0 10 FS total 0 15 in Vdc 15 acquisitions second 15 display refresh second lt 210mSec 0 to 99 signal 85 to 265 Vac dc 11 to 60 Vdc and 24 48Vac lt 4w 3500Veff for power H 2000Veff for power L all levels tested for 60 seconds 3 frontal push buttons and rear jumper for signal selec tion in Vdc or mA 10 segments yes configurable yes recur
13. isplay since the last reset of the memory Memory is reset on the following cases manual reset from the Configuration Menu Maximum change on the input signal Input modification on the scaling Scaling change on the decimal point dP modification of the linear ization segments or instrument power down Minimum Min Memory of minimum display Indicates the minimum value of display since the last reset of the memory Memory is reset on the following cases manual reset from the Configuration Menu minimum change on the input signal Input modification on the scaling Scaling change on the decimal point dP modification of the linearization segments or instrument power down Amplicon Sales 44 0 1273 570 220 Website www amplicon com Email sales amplicon com Datasheet Peak amp Hold P hLd Peak amp Hold function detects sharp drops in the displayed value and holds the display if a display drop is detected To disable the hold function for a moment press any of the front buttons or wait for a predefined time Time 0 hold disabled Off Time 1 a 3999 seconds before disabling the hold Time 4000 infinite hold The counting of seconds is started each time there is an in crease in the display value Alarms will follow the input signal while hold is active the alarm type Max Min the setpoint the hysteresis value the activation delay and the value of setpoint2 Off or the setpoint2 v
14. lays the available menu options During a value selection menu for example a setpoint value increases digit value from 0 to 1 2 3 4 5 6 7 8 9 Button LE Leaves the current menu Pressing LE several times will leave all menus and leave the Configuration Menu tree During a value selection menu for example a setpoint value allows to select each digit for modification with the UP button Reset Leaving the Configuration Menu forces a restart of the instrument even in case of no changes in configuration Information Menu mA or Vdc Bae Bada Baga Baas Memory of maximum Memory of minimum On Off Max Min Setpoint FERE Counts FERE Seconds REEE Second Option installed Option installed Option installed conf gt HHHH Configuration TT to Input Low dia Display Low Ihi Input High dhi Display High OAH gt 886d Maximum Minimum Lr I HAHHH Alarm1 HHHH HBAR hYSE Hysteresis JEL Delay GEE Setpoint2 A L r c See menu for Alarm1 A L r 4 See menu for Alarm1 A a r g See menu for Alarm1 oPE 1 HHHH Option1 oPE 2 HHHH Option2 aft 3 gt HHHH Option3 setpoint Option3 availabl
15. ll along the same conduits power cables power motor controllers electrovalves together with signal and or control cables Before proceeding to the power connection verify that the voltage level available matches the power levels indicated in the label on the instrument In case of fire disconnect the instrument from the power line fire alarm according to local rules disconnect the air conditioning attack fire with carbonic snow never with water Amplicon Email sales amplicon com Datasheet Front View Signal Connections Al Active current loop 4 20mA 20mA 12 3 ii 7 f i fi i f 7 A Jumper 5 closed GEG i pe urren Signal generator lt 4 u Common Passive current loop 4 20mA 20mA Logo Button LE Button SQ Units Button UP 123 BI Jumper 5 closed 5 Rear View oF 2 Wire Option3 Option1 Option2
16. lt e ry 7 m E 5 Resets to factory de fault values UE rf H H H H Firmware version Version L I G L gt L I G l Minimum brightness Brightness pT F3 LI We L I G J Default brightness IIT LI wu 4 aaa L i G 5 Maximum brightness o PE Configuration for Option Option1 o P L g Configuration for Option2 Option2 o p L J Configuration for Option3 Option Option3 available soon I FAL d on gt HABA Peak amp Hold F Time Sec m F E Foal aIL Tools 1 I Cc J m 1 H nm I 1 Addl gt Pnt5 foPl HOA di SU gt BEBA Advanced Points InputO DisplayO display pea I wm Pt C I Im m linearization L iL REEE di IH REEE Input10 Display10 DEEA Enter signal values Input and associated display val ues Display for each linearization point Then activate J Act to On In case of error verify the points data Ack on Activate Cc OFF Default factory configuration Range and scaling Decimal point Alarms 1 2 3 and 4 Active Type Setpoint Hysteresis Delay Setpoint2 Display Fixed digits Average Steps Left zeros Add zero to the right Memory of maximum Memory of minimum Peak amp Hold Tools Segments Password Brightness 4 20mA 0 1000 without decimal point Off not managed maximum 1000 0 counts 0 0 seconds Off Off Off Off Off Off 9999 9999 Off Off Off 3 Note Selecting an input range Input scales to the following values 4 20 mA
17. ment displays the minimum displayed value in memory The minimum visualization is active MAX The instrument displays the maximum displayed value in memory The maximum visualization is active P hLd The instrument displays the peak value Function Peak amp Hold is active Err 0 Values introduced on the ScAL menu are not valid Default values are activated The slope defined by the two points is almost vertical higher than 5000 Err 1 Err 2 The instrument has detected an installed option but was unable to communicate Err 3 Related to the edition of a linearization point Re turns to the point for further edition The value of InPX of the edited point is lower than InPX of the previous point Err 4 Related to the activation Act of the lineariza tion segments Ad dl Activation is not allowed The value InPX of one of the points is higher than InPX of the next point Err 5 Related to the activation Act of the linearization segments Ad dl Activation is not allowed The slope de fined by one of the segments is almost vertical Password incorrect Slope condition for Err 0 and Err5 dhI dLo Counts InI ILo mA or Vdo lt 5000 Amplicon Sales 44 0 1273 570 220 Website www amplicon com Email sales amplicon com Datasheet Accessing the instrument Option R1 1 relay Relay type 3 contacts Common NC NO Y
18. nipulation by non authorized personnel In case of mal function get in contact with your local provider to arrange for repair Within the warranty period and after examination by the manufacturer the unit will be repaired or substituted when found to be defective The scope of this warranty is limited to the repair cost of the instrument not being the manufacturer eligible for responsibility on additional damages or costs CE Declaration of Conformity Manufacturer FEMA ELECTRONICA S A Immunity rules Altimira 14 Pol Ind Santiga 61000 6 2 Generic rules of immunity E08210 Barbera del Vall s 61000 4 2 By contact 4KV Criteria B BARCELONA SPAIN On air 8KV Criteria B www fema es info fema es 61000 4 3 Criteria A Products M40 P 61000 4 4 On AC power lines 2KV Criteria B On DC power lines 2KV Criteria B The manufacturer declares that the instruments indicated On signal lines 1KV Criteria B comply with the directives and rules indicated below 61000 4 5 Between AC power lines 1KV Criteria B Directive of electromagnetic compatibility 2004 108 CEE Between DC power lines 0 5KV Criteria B Directive of low voltage 73 23 CEE 61000 4 6 Criteria A Security rules 61010 1 61000 4 8 30A m at 50Hz Criteria A Equipment Fixed 61000 4 11 0 1 cycle Criteria A Permanently connected Pollution degree 1 and 2 without condensation Isolation Double Category CAT II Emission rules 61000 6 4 G
19. oint The alarms configured as maximum are deactivated when the display is lower than the setpoint The alarms configured as minimum have the inverse behavior Setpoint SEt Value from 9999 to 9999 Alarm set point IT and Instrumentation for industry Functions on this menu allow for configuration of the display Fixed Digits FIX d Allows a digit to be fixed to a predefined value for example least significant digit fixed to O It is a condition to fix a digit that all digits to its right are also fixed Value shows that the digit is not fixed Average AVr Recursive filter applied to display Value from 0 0 to 99 9 The severity of the filter increases with the value selected Increasing the severity of the filter makes the display response slower Steps StEP Display changes on predefined steps Values are 1 2 5 10 20 and 50 The display is made in steps of X counts For example select a step of 20 will make the display to change in steps of 20 1420 1440 1460 Left Zero LZEr Value On Off Select On to visualize zeros to the left Add Right Zero rZEr Add a zero to the right Value On Off Select On to light a fifth digit on the display placed to the right LSD position and fixed to a value of O Maximum display reading is now 99990 and minimum 99990 Maximum MAX Memory of maximum display Indicates the maximum value of d
20. ory of measure and the degree of pollution levels that apply Instrument protected with double isolation No earth connection required Instrument is in conformity with CE rules and regulations See CE Declaration of Conformity further in this document Installation of this instrument must be performed by qualified personnel only This manual contains the appropriate information for the installation Using the instrument in ways not specified by the manufacturer may lead to a reduction on the specified protection level Disconnect the instrument from power before starting any maintenance and or installation action IT and Instrumentation for industry Sales 44 0 1273 570 220 Website www amplicon com The instrument does not have a general switch and will start operation as soon as power is connected The instrument does not have protection fuse the fuse must be added during installation The instrument is designed to be panel mounted An appropriate ventilation of the instrument must be assured Do not expose the instrument to excess of humidity Maintain clean by using a humid rag and do NOT use abrasive products such as alcohols solvents etc General recommendations for electrical installations apply and for proper functionality we recommend if possible install the instrument far from electrical noise or magnetic field generators such as power relays electri cal motors speed variators If possible do not insta
21. ou may need to access the inside of the instrument to insert Maximum current 8A resistive load additional options Use a flat screwdriver to unlock the upper Voltage 250 Vac continuously clips marked with A Then unlock the lower clips marked Instalable in Option and or Option2 and or Option3 with B and move out the front filter Let the inside of the instrument slide out of the housing Connections for Option and 2 GHI BCD Connections for Option3 Option3 available soon To reinsert the instrument make sure that all modules are correctly connected to the pins on the display module Place all the set into the housing assuring that the modules cor rectly fit into the internal guiding slides of the housing Once NC introduced place again the front filter by clipping first the upper clips A and then the lower clips B NO NC NO LMN Important If your instrument was delivered with the IP65 front seal option accessing the inside of the instrument will permanently break the IP65 seal on the areas of clips A and B Com Com Warranty All instruments are warranted against all manufacturing defects for a period of 24 MONTHS from the shipment date This warranty does not apply in case of misuse accident or ma
22. sive configurable yes configurable yes yes yes configurable yes configurable yes configurable yes yes yes yes yes yes 5 levels IT and Instrumentation for industry Thermal stability offset 25 ppm C span 60 ppm C span drift includes the offset drift maximum 2 board 3 available soon Optional boards Mechanical Mounting panel Connections plug in screw terminals Weight lt 150 grams Housing materials ABS polycarbonate vergaflex Front size 96x48mm Panel cut out 92x44mm Deep from panel 91mm including terminal IP54 standard IP65 optional Front sealed Open ing the front breaks the seal Protection Temperature Operation 0 to 50 C Temperature Storage 20 to 70 C Warm up 15 minutes 30 minutes when using Vexc Mechanical Dimensions mm oom 96 16 75 8 Panel cut out 92 Amplicon Sales 44 0 1273 570 220 Website www amplicon com Email sales amplicon com Datasheet Operating the Information Menu To enter the Information Menu press the SQ button The Information Menu allows to visualize information and does not allow to modify the configuration of the instrument It is not affected by the PASSWord function During operation with the Information Menu alarms remain frozen and are
Download Pdf Manuals
Related Search