Operating manual High-pressure cleaners
Contents
1. The hose may under no circumstances be pulled over sharp edges since otherwise the guarantee is automatically void kr mzie IZ Putting into operation 1 Move high pressure cleaner to the job site The Kr nzle Silent 120 is a movable machine with sturdy trolleys ideally suited for difficult terrain and stairs I Setting up location Neither set up or operate the machine in rooms where d there is a risk of fire or explosion nor put it into puddles Do not use the machine under water 2 Check water inlet filter for cleanli ness prior to putting the machine into operation Manually unscrew hose attachment Take out the serial water inlet filter using needle nose pliers and clean if filter is soiled 3 Each time check oil level at oil level glass prior to putting HP cleaner into operation Take care that cleaner is in horizontal position The oil level must be visible in the centre of the oil level glass 4 Insert spray lance into gun kr mzie H EEE _ A Screw together lance and gun ae WW 6 Unwind high pressure hose straight gt and without nooses When using hose extensions take care that the max length of 20 m is not exceeded 7 Push on HP hose to gun 8 Tightly screw together HP hose and t gun 9 Put HP cleaner into horizontal position These machines must be oper2. if the oil turns grey you must change it N In case of increased humidity or fluctuations in kr mzie Safety precautions Bear in mind that during cleaning tasks with a high pressure water jet a significant recoil at the lance arises see technical data on page 4 Apply the safety catch on the spray gun after each use in order to prevent unintentional spraying Always aim the underbody lance Bear in mind when using a curved or angled spraying lance that there is a significant amount of torque in the recoil kr mzie D Safety precautions This is prohibited Never direct the water jet at people or animals Only use power cables which are in perfect working order Do not dama ge the power cable or repair it incor rectly Never pull the high pressure hose if it has formed kinks or nooses Never pull the hose over sharp edges kr mzie Never allow children to use the high pressure cleaner Never direct the water jet at the machine itself Never expose the machine to the spray mist of the high pressure water jet Never direct the water jet at a power socket kr mzie Please note important IH Lack of water Lack of water occurs more often than you probably believe The more powerful a g high cleaner is the greater is the danger Pa
3. 16 O Ring 9 3 x 2 4 2 13 273 17 Kunststoffschraube 5 0 x 20 20 43 018 18 Auflagepuffer 2 44 510 19 Kunststoffschraube 5 0 x 30 2 41 412 20 Scheibe 40 x 6 x 1 5 Stahl 2 45 216 7 21 Unterlegscheibe 8 4 4 50 186 22 Innensechskantschraube M 8x 30 4 41 036 3 23 Kunststoffschraube 4 0 x 16 2 43 417 26 Kunststoffschraube 3 5 x 14 2 44 525 28 Pistole M2000 mit ISO Handgriff 1 12 489 29 Lanze mit Flachstrahld se 028 1 12 392 5 M20028 30 Schmutzkiller 028 1 41 571 028 31 Kabelklemme 1 43 431 32 Schraube 3 5 x 16 2 44 161 33 Griffabdeckung 1 44 535 34 Gummipuffer links rechts 1 44 536 35 Rad kpl 7 8 10 15 20 2 44 538 2 kr mzie EJ Spare parts list kr mzie Kr nzle 122 Silent Motor DI No Description Qty Ord No 1 lgeh use mit Dichtung Deckel ldichtung Schulterlager 1 44 501 2 Stator 1 23 001 2 3 Motorwelle mit Rotor 1 43 104 4 Passfeder 6 x 6 x 20 1 41 483 1 5 Motor Lager B Seite Z Lager 1 43 025 6 Motor Lager A Seite Schulterl 1 43 026 7 Schelle f r L fterrad 1 44 534 1 8 ldichtung 25 x 35 x 7 1 41 024 9 Lufterrad 1 44 534 10 L fterhaube 1 41 497 11 Flachdichtung 1 44 513 12 L sterklemme 2 pol 1 43 031 13 Schaltkasten 1 44 508 14 Schalter 8 5 A 1 43 329 15 Klemmrahmen mit Schalterabdichtung 1 43 453 16 Kabelverschraubung PG 11 1 41 419 17 Gegenmutter PG 11 1 44 521 18 Kondensator 40 uF 1 43 035 1
4. 26 Spare parts list 28 Complete assembly 28 Motor 30 Transmission 32 Valve housing 34 Gun with lance 36 Wiring diagram 37 Inspections inspection reports 38 kr mzie D Tecnical data V Operating press continuously adj 44 m Silent 120 Kran Kranzle 122 Silent 10 120 bar 1700 PSI Nozzle size 20 028 Permissible overpressure 135 bar Water output at 1 400 r p m 7 l min Water inlet temperature max 60 C Sucton height 1 5 m Steel weave high pressure hose 10m Detergent suction special accesories Connected load 230 V 7 5 A 50 Hz Power input P1 1 6 kW Power output P2 1 0kW Weight 25 kg Dimens incl pulling handle in mm 300 x 330 x 800 Sound level acc to DIN 45 635 71 dB A Acoustic power LWA 84 dB A Recoil at lance ca 27 N Vibration at lance 1 9 mis Order no 41 221 Permissible tolerance for figures 5 acc to VDMA uniform sheet 24411 kr mzie This is what you have purchased D 1 Kr nzle high pressure cleaner 122 Silent Safety spray gun with insulated handle and screw connection OSE 3 Washing lance with Kranzle knife jet nozzle 4 Steel weave high pressure hose 10 m NW 6 kr nzis 5 Operating manual kranzie D General rules IH Range of application Use machines for cleaning tasks with high pressure water jet and detergents
5. as that a lack of water occurs If there is only So N Ge an insufficient amount of water available EG _ a i PAR i cavitation water gas mixture arises inside the pump which is normally noticed too late or even not at all The pump will be destroyed Please check the available quantity of water by filling a bucket with litre scale for one minute A minimum water quantity of 7 litres per minute must be available to guarantee a trouble free operation of the Kr nzle 122 Silent If the metered quantity of water is too small you have to use a diffe rent water connection guaranteeing the necessary output A Lack of water leads to an accelerated wear of the joints no guaran tee IH Water supply Please pay attention to the regulations of your waterworks company In accordance with DIN EN 61770 the machine may not be directly connected to the public drinking water supply lines A brief connection however is permissible according to DVGW German Association for Gas and Water Affairs if a non return valve with tube ventilator Kr nzle order no 41 016 4 is built into the water supply Once the water has passed through the non return valve it is no longer con sidered as drinking water Also indirect connection to the public drinking water supply lines is permissible by way of free emission in accordance with EN 61 770 e g by using a reservoir with a float valve Direct connection to a non drinking water
6. or with high pressure water jet without detergents only I Inspections The machine must be inspected according to the Guidelines for Liquid Spray Devices at least once every 12 months by a qualified person to ensure that continued safe ope ration is guaranteed The results of the inspection are to be recorded in writing This may be done in any form For inspection reports see pages 38 39 A High pressure cleaners used for commercial purposes have to be checked by a qualified person at least every 12 months IM Accident prevention The machine is designed for accidents to be impossible if used correctly The operator is to be notified of the risk of injury from hot machine parts and the high pressure water jet The Guidelines for Liquid Spray Devices must be complied with see pages 8 and 9 WOU change 1 The first oil change should be carried out after approximately 50 operating hours After that no further oil change will be necessary for the life cycle of the high pressure cleaner UPut the machine into a horizontal position then open the oil discharge screw at the bottom of the device over a collection reservoir The oil is to be caught in the reser voir and disposed of in an approved manner New oil 0 25 I Motor oil W 15 40 Oil leakage If oil leaks contact your nearest after sales service dealer at once Ecological damage damage to the transmission temperature development of condensed water is possible
7. through nozzle opening If this procedure is not successful the nozzle has to be dismantled and cleaned or even replaced if necessary A CAUTION Pull plug from socket prior to starting any repair work kr mzie IM Pressure gauge shows little pressure the water from the nozzle comes in squirts Most likely the valves are soiled The pressure gauge shows little pressure despite fully turned up pressure regulation The water from the lance comes in squirts The HP hose vibrates Inside the pressure gauge is no water but a filling with glycol to damp the vibration of the pointer Proceeding Unscrew all 6 valves one after the other hexagonal brass screws 3 in a row vertically and horizontally Take out valve body with green or red plastic coating and O ring by means of needle nose pliers Check O ring for damage In case of a damage the O ring has to be replaced Take a wire and clean valves under running water Do not forget the O ring during x reassembly kr mzie 22 Small repairs do it yourself I The pressure gauge shows full pressure although the gun has been closed The pressure switch valve switches constantly Possible cause no 1 Leakage Having closed th gun the HP cleaner must shut down and the pressure gauge must show 0 bar If the pressure gauge still shows full pressure and the motor constantly switches on
8. 0 LY L Bunjddnyyoe1g 6r L LYO LY L Buuqyoiq wwng gy C 9v0 Lv L Joy nesseM Op EIN L ssniyosue nes Gr 6rl VL L Jejdny Duunumg tt LILO LY 4 ZV SPXEN Jyasyueysysasusuu y ECO Ob 4 ZV SEXEN yosyueysyo su uu Zr EA 4 Bunys g wniuwnyy ZE Br El L uajdoyssnjyosian OC CG Fb L ABejyasyon js ny In aysHueBsny GE L OZI YL JopajBejyosyony VE sso er Bunzynysay yw Bunusyasmz gg ZC0 Gk E Buuabeyoe Le vc0 6V ZX vz Dupto OF oN p o AIO uondusseq ON vl Ly 9 t xy bumpeg 67 LELo Ly G Z G X YZ X pL OHoyOsueW eqamed Lo ELS Lv GZS X YZ X pL aHeyosueyy 87 819 Lv Duusmne ZZ POOL JeyswoueN o 0S0 v edund Zv peipueH Injeddey Sz OLO er 9 MS Wu 9 N Jonn bz 6Y0 v edund ZV IN 9 IN peipueH ez 8Y0 v 1ebe js6ny zz LY0 v aqieyosyonupsepe4 LZ 9Y0 t dwnd Zy inj ziemyps Jope4 OZ LZZb pL Zz QW Jon 6L LOEL PL ww g Gunuu juegioy 84 Sv0 t egeyS SN Z4 zezi vi ww 9 japulds 1 syegied 94 LEZI YL WW FL uaqoy any Seu GI uabunyyoiq WU Zes tt Zy Any ww 9 Ueg ogien8 s HL SLL VL L BANEIYISSSNIYUISIOA CL 6ll vi Jepej ye s epg ZI Amal ww 0 0 e6ny 4ejs epg LI DO EE IRueasfunysejuejnejuy LL Love zZ Duusbuneune OL SLL vl Zz Zus yejs epa 6 9371 Zz S X 6uR O 8 LSOO SL tl zxz duo A CO er LXOLWuadoysyyiq 9 ssr el X8Wueydojs uo a LZI9 Ly 9 ozr 2 GH und ou A L LLO LY 9I BIL Ww eidelen L O Lt G u jdojsjyu A Z 020 6r e
9. 9 Netzkabel f r 230V 50 60Hz 1 41 092 20 Blechschraube 3 5 x 9 5 2 41 088 21 Blechschraube 2 9 x 16 1 43 036 22 Innensechskantschr M 5x 12 4 40 134 23 Innensechskantschr M 5 x 30 4 42 130 24 Erdungsschraube kpl 1 43 038 25 Deckel f r Schaltkasten 1 44 512 26 Dichtung f r Deckel 1 44 522 27 Kunststoffschraube 5 0 x 25 4 41 414 28 Blechschraube 3 9 x 9 5 3 41 636 29 Toleranzh lse 1 43 063 1 40 Motor kpl 1 44 586 kr mzie Spare parts list kr mzie Kr nzle 122 Silent Transmission unit 33 No Description Qty __Ord No 1 Geh useplatte 1 43 003 2 ldichtung 14 x 24 x 7 3 41 631 3 O Ring 83 x 2 1 43 039 4 Plungerfeder 3 43 040 5 Federdruckscheibe 14 mm 3 43 041 6 Plunger 14 mm 3 43 005 7 Sprengring 14 mm 3 41 635 8 Taumelscheibe 12 1 1 41 028 12 1 10 Axial Rillenkugellager 3 teilig 1 43 486 12 Innensechskantschraube M 8 x 25 4 40 053 13 Verschlussschraube M 18 x 1 5 1 41 011 14 O Ring 12x 2 3 15 005 1 15 lschauglas 1 42 018 1 16 lverschlussschraube rot 1 43 437 17 Dichtung ldeckel 1 44 501 1 18 Deckel lgeh use 1 44 501 2 19 Innensechskantschraube M 5 x 12 4 41 019 4 kr mzie Spare parts list kr mzie Kr nzle 122 Silent Valve housing Z 06S bt dy osneya yusA 4 L t DEIDUEH u du uaqjoysena g 04 CO Bb uayayosueyy zyes njeredey 19 L 89 Lb un 6 a yusy zyes dey 09 ObbCk L zxg Dupto ZS LOL L Buy O 0S C Lv
10. Operating manual High pressure cleaners kramzie HOCHDRUCKREINIGER 122 Silent D F www kraenzle com CE Atl Ge Read and conform safety instructions before use Keep instructions in a safe place for later use and pass them on to any future user TGBT naic made In Germany kr mzie 2 Description Kr nzle 122 Silent ler kranzle 122 Sl Ergonomically shaped handle High pressure gun Pump head made of special brass for a long service life Large stainless steel manometer Continuously adj pressure control Cable reel with 5 m cablel On Off switch with motor protection Receptacle for washing lance Receptacle for high pressure gun Trolley suited for difficult terrain and stairs kr mzie Contents Page Description of appliance 2 Contents 3 Technical data 4 Overview This is what you have purchased 5 General rules 6 Safety precautions accident prevention 6 Extremely important Water connection electr connection 7 Kranzle technology 10 Water and cleaning system 12 Lance and spray gun 12 Pressure control valve safety valve 12 Motor protecting switch 12 High pressure hose and spray device 13 Putting into operation 13 Connection to water mains 14 Direct suction 14 When using detergents 18 To shut down the pump frost protection 19 Small repairs do it yourself 20 EG Declaration of Conformity 24 Guarantee 25 Accessories for high pressure cleaners
11. and off the possible reason for this can be a leakage of the pump the HP hose or the lance Proceeding Check the connections from the HP cleaner to the the HP hose from the hose to the gun and also the connection between lance and gun for tightness Switch off the cleaner Shortly press the trigger of the gun to decrease the pressure Unscrew HP hose gun and lance and check the O rings If the O rings are damaged they have to be replaced In case of a leakage there is no guarantee for possible consequential damages kr mzie IH The pressure gauge shows full pressure although the gun has been closed The pressure switch valve switches constantly Possible cause no 2 The non return valve body is soiled or the O ring at the non return body is defective Proceeding Switch off machine and pull plug from socket Stop water supply Unscrew pump outlet Take out non return valve body and check for soiling or damage of the O ring Replace O rings in case of damage There is no guarantee if the pump is damaged by defective O rings due to air induction or lack of water cavitation kr mzie 24 EC declaration of conformity I hereby we declare that the high pressure cleaners technical specifications available from Nominal flow comply with the following guidelines and their a
12. ated in horizontal position Connect high pressu re hose to pump and connect tightly IH Be careful when using hot water of 60 C raised temperatures occur Do not touch the When running your high pressure cleaner with hot water A metal parts of the cleaner without safety gloves kr mzie D Putting into operation 10 Connect water hose to water inlet The cleaner may be connected to a water mains 1 8 bar pre pressure with either Ve cold or up to 60 C warm water o 11 Connect to circuit Kr nzle 122 Silent 230 V 7 5 A 50 Hz P The socket must be protected with a 16A delay action fuse on the mains side 12 Steplessly adjust operating pressure with handwheel The maximum pressure is adjusted ex work 13 Switch on high pressure cleaner with opened spray gun Bleed appliance Gun has to be opened and closed several times Start cleaning task kr mzie Direct suction Di Sucking in water from ponds rain butts etc Due the suction capacity of its pump up to 1 5 m suction height max hose length 2 m this high pressure cleaner can suck in water for cleaning purposes from separate contai ners or ponds Prior to starting the first suction the pump resp the suction hose has to be filled with water AU N an S S K gS Ss AS S Attach su
13. ction hose The inner diameter of the hose must be at least 3 4 16 mm Best use suction hose with suction filter from the Kr nzle accessories Order no 15 038 3 Use clean water only kr mzie Suction of detergents IE Detergent suction set Kr nzle accessories order no 13 376 5 By installing a detergent injector between pump and high pressure hose detergents can be sucked in and mixed into the water jet d To be able to do this it is necessary to use a sucton set lance with adjustable regulation nozzle from high to low pres sure as the suction process only works ifthe machine operates in low pressure By adjusting the regulation nozzle to high pressure the supply of detergents is stopped 1 Unscrew high pressure hose and mount detergent injector to the high pre sure outlet and connect to HP hose 2 Insert injector hose with filter into the container with the detergent 3 Switch on cleaner with opened gun and set the regulation nozzle of the lance to low pressure detergent admixture 3 5 4 Let detergent act and then spray off with high pressure water jet Observe specifications of detergent manufacturer ment etc Caution dissolvents e g protective equipment rules for waste water treat Never suck in liquids containing solvents like varnish solvents petrol oil or similar liquid Observe specifications of detergent manufacturers S
14. e technology IH Wasser and cleaning system Water can be connected at mains pressure 1 8 bar pre pressure9 to the high pressure pump or it can be sucked directly from a storage tank The water is then forced under pressure by the high pressure pump to the lance The high pressure jet is formed by the nozzle at the end of the lance M Environmental refuse disposal and water protection regulations must be observed IH Lance with spray gun The machine can only be operated when the safety trigger of the gun is squeezed When the lever is squeezed the spray gun opens The liquid is then pumped to the nozzle The spray pressure increases and quickly reaches the selected operating pressure When the trigger is released the trigger gun closes and any further spraying of liquid from the lance is stopped The increase in pressure when the trigger gun is closed causes the pressure control valve safety valve to open The pump remains switched on and works with recuced overpressure in by pass When the spray gun is opened the pressure control valve safety valve closes and the pump resumes pressure spraying from the lance with the selected operating pressure The spray gun is a safety device Repairs should only be performed by qualified persons Should replacement parts be required use only components authorized by the manufacturer IH Pressure control valve safety valve The pressure control valve safety valve protects the machine fr
15. eals inside the appliance are no resistant against solvents The spray mist of solvents is highly inflammable explosive and poisonous kr imzie To shut down the pump D 1 Switch off the machine 2 Cut off the water supply 3 Open the spray gun briefly until the pressure is released 4 Apply the safety catch on the spray gun 5 Remove the water hose and spray gun 6 Drain the pump switch on the motor for approx 20 seconds 7 Pull the plug from the socket 8 Clean HP hose and wind up 9 Clean power cable and wind up 10 Clean water filter 11 Winter store the pump in rooms above 0 C IH Store in a place saving manner WW AU Due to their compact and space saving design the Kr nzle Silent cleaners can be stored practically anywhere kr mzie 20 Small repairs do it yourself I No water from the nozzle but the gauge shows full pressure Most likely the nozzle is blocked The pressure gauge shows full pressure but from the nozzle comes only little water or no water at all Inside the pressure gauge is no water but a filling with glycol to damp the vibration of the pointer Proceeding Switch off the cleaner Pull plug from the socket Operate gun seveal times to decrease the pressure First unscrew gun and lance then rinse hose from any residues Check water inlet filter for soiling If the problem still exists take wire paper clip and push
16. mendments for high pressure cleaners Sound level measured Sound level guaranteed Applied conformity evaluation procedures Applied specifications and standards Kr nzle GmbH Elpke 97 D 33605 Bielefeld Bielefeld 04 07 2013 Kr nzle 122 Silent Manfred Bauer Fa Josef Kr nzle Rudolf Diesel Str 20 89257 Illertissen 420 I h machinery directive 2006 42 EEC EMV directive 2004 108 EEC noise directive 2005 88 EC Art 13 HP water spraying machines annex 3 part B chapter 27 81 dB A 84 dB A annex V noise directive 2005 88 EC EN 60 335 2 79 2009 EN 55 014 1 2006 EN 61 000 3 2 2006 EN 61 000 3 3 2008 of Kranzle Josef Managing director kr mzie Guarantee D I The guarantee is only valid for material and manufacturing errors Wearing does not fall within this gurantee The instructions in our operating manual must be complied with The operating instructions form part of the guarantee The Guarantee is void if other parts are used than genuine Kranzle accessory parts or genuine Kranzle spare parts For high pressure cleaners sold to the user the guarantee period is 24 month For high pressure cleaners sold for industrial use the guarantee period is 12 month In the case of a guarantee please contact your dealer or authorized seller delivering accessories and your purchase receipt You can fin them in the internet under www kraenzle com The guarantee is also void if the machine i
17. om a build up of excess pressure and is designed not to permit an excess pressure to be selected for operation The limit nut on the handle is sealed with a spray coating The operating pressure and spray rate can be steplessly adjusted by turning the handle Replacements repairs new adjustments and sealing should only be performed by qualified persons kr mzie IH Motor protection switch The motor is protected from overload by a motor protection switch which cuts out the motor in the event of overload However should the switch trip frequently the cause of the malfunction should be located and rectified see page 11 Replacements and inspection work should only be performed by qualified persons when the machine is disconnected from the power supply i e with plug pulled out from the electrical socket IH High pressure hose and spray device The high pressure hose and spraying device supplied with the machine are made of high grade material they are also optimized for the machine and marked as required by the appropriate regulations max hose length 20 m If replacement parts are required only such parts that are authorized by the manufacturer and which bear the markings A required by the appropriate regulations may be used The high pressure hose and spray device must be connected in a pres sure tight manner without leakage The high pressure hose may not be driven over pulled exces A sively or twisted
18. r nzle test seal Order no UVV200106 Owner Address Scope of inspection o k yes no repaired Type plate on hand Operating manual on hand Protective covering device Pressure line tightness Pressure gauge function Float valve tightness Spraying device marking HD hose connector damage marking Safety valve opens at 10 20 exceeding of operang pr Power cable damage Protective conductor connectedt On Off switch Used chemicals Allowed chemicals Inspection data determined value set value High pressure nozzle Operating Dreseure bar Switch off pressure bar Conductor reist not exceeded value Insulation Leakage current Gun locked Inspection result tick L The appliance was checked by an expert according to the Guidelines for Liquid Spray Equipment the defects found have been rectified so that the Labour Safety can be confirmed The appliance was checked by an expert according to the Guidelines for Liquid Spray Equipment The Labour Safety cannot be confirmed unless the defects found are rectified by repair or replacement of the faulty parts The next retest according to the Guidelines for Liquid Spray Equipment has to be carried out by Month NOAM muster us Place date Signature kr mzie Inspection report for HP cleaners EJ Inspection report on annually carried out Labour Safety Inspec
19. s used with exceeding the temperature and speed limits a voltage below the required rating with less than the required amount of water or with dirty water Pressure gauge nozzle valves sleeves high pressure hose and spray equipment are wear parts and are not covered by the warranty kr mzie Versatile due to Kr nzle accessories Rotating washing brush with 400 mm extension Order no 41 050 1 Underbody lance with 800 mm extension Order no 41 075 Dirtkiller lance rotating point jet nozzle with intensive cleaning effect Order no 41 073 8 Order no 41 850 TI Suction hose with suction filter Order no 15 038 3 Splash protection Order no 41 052 Floor cleaner round cleaner UFO SM Ul kr mzie 28 Spare parts list kr mzie Kr nzle 122 Silent Complete assembly 29 No Description Qty Ord No 2 Fahrgestell 1 44 502 3 Frontplatte 122 Silent 1 44 503 9 4 K cher gro 1 44 506 5 K cher klein 1 44 507 6 Knickschutz 1 44 509 7 Rad 2 44 538 8 Radkappe 2 45 2008 9 Kabelhalteplatte 1 44 505 10 Achse 2 44 504 11 Netzanschlusskabel 1 41 092 13 Versteifungsplatte 1 44 511 15 Kunststoffsenkschraube 5 0 x 20 2 45 421 1
20. sneys inug 1 ON pPJO AID uonduosaq ON kr mzie S pare parts list Kr nzle 122 Silent Gun with lance a No Description Qty Ord No 1 Pistolenschale kurz rechts links 1 12 455 2 Schraube 3 5 x 14 11 44 525 3 Reparatursatz M2000 12 454 4 Abschlusskappe 1 12 459 14 Aluminium Dichtring 2 13 275 1 15 Rohr kunststoffumspritzt bds R 1 4 AG 1 15 004 2 16 berwurfmutter ST 30 M22 x 1 5 IG 1 13 276 1 17 Au en Sechskant Nippel R 1 4 IG 1 13 277 1 18 O Ring 9 3 x 2 4 1 13 273 51 D senschutz M12x1 1 26 002 1 52 Rohr 400 mm bds M12x1 1 15 002 53 ST 30 Nippel M 22 x 1 5 R1 4 m ISK 1 13 363 54 Flachstrahld se 028 1 M20028 55 Aluminium Dichtring 2 13 275 M2000 Pistole kpl 12 480 Lanze kpl mit HD D se 028 12 392 5 M20028 kr mzie Wiring diagram Ed Kranzle 122 Silent C 40 uF ci Terminal strip as DEE BI Weber Unimat WT 22 551 sies 8 5 A Excess current release ka az RR ae Fr P2 bl ee oN Hi E i i I i a ees eee Pit 4 E schw 4 Gg a D ge gn pr Motor stator kr mzie EJ Inspection report for HP cleaners Inspection report on annually carried out Labour Safety Inspection UVV according to the Guidelines for Liquid Spray Equipment This inspection sheet serves as proof for the completion of the retest and must be kept carefully K
21. supply line is permissible kr mzie 7 I Insufficient quantity of electricity If there are too many collectors in your proximity connected to the network at the same time the available voltage and the current intensity may decline Consequent ly DV the motor of the high pressure cleaner does V not start or even blows The power supply may also be insufficient if the power cable is too long or too thin If extension cables are too long this may lead to a voltage drop causing malfunctions or start up difficulties Kranzle 122 Silent 230 V 7 5 A 50 Hz Check the line fusing and have the voltage and the available current intensity checked by an expert in case of uncertainty IH Electrical connection The machine is supplied with a 5 meter electrical power cable with plug The mains plug must be fitted to a standard grounded socket with a 30mA residual current operated device The socket must be protected with a 16A delay action fuse on the mains side When using an extension cable this must have an earthed lead which is properly connected to the socket The conductors in the extension cable must have a minimum cross section of 1 5 mm Plug connections must be of a spray proof design and may not be located on a wet floor With extension cables of more than 10 m the minimum cross section must be 2 5 mm When using a cable drum always keep the cable wound as far as possible kr mzie 12 Kr nzl
22. tion UVV according to the Guidelines for Liquid Spray Equipment This inspection sheet serves as proof for the completion of the retest and must be kept carefully Kr nzle test seal Order no UVV200106 Owner Type Ka AE sdenee ged hes sone tensecen tenn tag tos s epee ey Address Sarak se NR enone Rep order no Scope of inspection o k yes no repaired Type plate on hand Operating manual on hand Protective covering device Pressure line tightness Pressure gauge function Float valve tightness Spraying device marking HD hose connector damage marking Safety valve opens at 10 20 exceeding of operang pr Power cable damage Protective conductor connectedt On Off switch Used chemicals Allowed chemicals Inspection data determined value set value High pressure nozzle Operating Dressure bar Switch off pressure bar Conductor reist not exceeded value Insulation Leakage current Gun locked Inspection result tick L The appliance was checked by an expert according to the Guidelines for Liquid Spray Equipment the defects found have been rectified so that the Labour Safety can be confirmed L The appliance was checked by an expert according to the Guidelines for Liquid Spray Equipment The Labour Safety cannot be confirmed unless the defects found are rectified by repair or replacement of the faul
23. ty parts The next retest according to the Guidelines for Liquid Spray Equipment has to be carried out by Month Year Place date Signature I Kr nzle GmbH Elpke 97 D 33605 Bielefeld Reprint only allowed with the authorization of Kranzle As date of 04 07 2013 Ach made in Germany y o KH o KH M o 5 o gt o EI c o a o gt o a o c o EI o o o 2 5 N
Download Pdf Manuals
Related Search