绘王数位板 Win说明书
Contents
1. 4 Digital Pen Pressure Sensitivity Test lll Pen Storage and Maintenance IV Question amp Answer 1 1 1 2 2 3 6 7 8 9 15 I General Information 1 Overview Welcome to the world of tablet and digital pen You are able to discover how easy to control your personal computer by using a wireless digital pen instead of a mouse The function of the digital pen is able to draw a very thin thick light or dark called pressure sensitivity line You also can write sign annotate documents and draw sketch or paint as easily as you would on normal paper and simulate the functions like pencil mark pen brush or water color pen by using the commercial software packages such as Adobe Photoshop Corel Painter and Paint Shop 2 PenTablet Functions After installing the device driver your graphic tablet has the following functions 1 Direct pointing You can move the cursor to any area of the screen by hovering the digital pen tip over the tablet s surface 2 Three buttons mouse commands Your pen tablet provides sall functions of a three buttons mouse by using its pen tip and two buttons 3 Pressure sensitivity This feature allows you to emulate various brushes and pencils and you can press down the pen tip harder lighter stronger or thicker and subtle pencil lines you will receive 3 System Requirements Window2. Power switch Battery slot USB receiver 2 Working mode for Wireless Pen Tablet 1 Pull out the USB cable switch On Off button to On then plug in the wireless receiver 2 Constant working time gt 30 hours 3 The LED indicator flashes red when the battery level is lt 20 4 For battery power saving please switch On Off button to OFF when you don t use it 5 Automatic shutdown 200 uA the tablet will turn off automatically when it is used for over 20 minutes Push switch ON gt OFF gt ON restart 3 Working mode for Wired Pen tablet Switch On Off button to OFF then plug in the USB cable 6 3 Follow the steps to verify if the tablet is installed properly The LED light on the tablet is the main indicator for hardware operation and depending on your pen tablet model it may be located at a different place that shown in the above diagram This LED normally stays off and will only turn on or off in response to various conditions Watch the state of the LED on the tablet as you go through these test steps 1 Press down the switch button at the top of the pen then the pen will be turned on and activated If you want to quit your work press it again to turn it off 2 As soon as the graphic tablet itself activates the LED will be lit briefly and will then go and stay off again 3 When the tablet detects the presence of the digital pen the LED wil
3. IE Phone and Modem ed Programs and Features 9 Region and Language SmartAudio 6 Speech Recognition 16 System LL Taskbar and Start Menu Troubleshooting ie Windows CardSpace Windows Firewall g Windows Update 1 Adjust your computer s settings View by Smallicons val a porns Navigational flicks Navigational flicks and x a editing flicks L Disabled LP Customize F O Sensitivity You can adjust how easily your flicks are recognized A more relaxed setting may lead to accidental flicks m elaxed Precise Touch E Display flicks icon in the notification area Practice using flicks 4 0K can apply II j Second Button Right Button v ae Keyboard Keys v _ Support TabletPC click to visit website Pressure sensitivity Screen setting Monitor 1 Width 1280 Height 800 Main v Advanced Setting Simulate Mouse Left Hand Work Scope and Hotkey Pendisplay Calibration Device is disconnect ox J cae ay Ne 5 Control Panel gt AlliControl Panel Items gt Adjust your computer s settings View by Small icons Y Pen and Touch ag trong Gps wal amp Keyboard Pen Options Flicks Handwriting Touch Lenovo Power Controls Pen actions Use the pen to interact with items on the screen You can adjust
4. Lenovo s Notebook Fingerprint Reader E the settings for each pen action P Mouse 28 Notification Area Icons Equivalent mouse action Pen and Touch M Performance Information and Tools UE Phone and Modem Programs and Features 9 Region and Language SmartAudio a Pen buttons Use the pen button as a right click equivalent Use the top of the pen to erase ink where available 6 Speech Recognition jd System LL Taskbar and Start Menu Troubleshooting i Windows CardSpace BESFBRO4ASE SS BAGH Windows Firewall g Windows Update Z Press and Hold Settings Speed You can change the amount of time you must press and hold before you can perform a right click equivalent You can change the amount of time during press and hold to perform a right click action Duration Test settings To test your settings press and hold the graphic The graphic changes when you perform press and hold successfully
5. Button Right Button functions represent for a normal mouse left middle right button functions 2 When choosing Middle Button the corresponding pen button will has the same Press function as a normal mouse but doesn t have the Scroll function 3 When choosing the Keyboard Keys there will appear an Express Key Settings as Picture ll You can set the pen button functions as the same as any Express Key or Keyboard Keys functions as Picture IIl Digital pressure sensitive pen default setting functions 1 The pen nib is equivalent to the mouse left button function 2 When the first key is E you can switch it to eraser in the graphic software such as photoshop etc 3 The second key is equivalent to the mouse right function 3 Workspace and Hotkey Settings Advanced Setting Simulate Mouse Ez Left Hand Pen Monitor Calibration Click the Work Scope amp Hotkey button in tablet settings see the selected area above you can access the working area and shortcut key settings 3 1 Workspace Settings Area A Area C The work area Softkey settings area Area D Softkey Area A i Area B Express key Full Area Disable Soft Key Area C The work area Sr 52505 Se 2505 SSS a CA Se ates Sr rates 52505 SN Sa Sen Pe 55 aa ble softkey Disa the work area Area C ings area ings a
6. Keys SS 5505 5 5550505 SESI SS The work area 4 Digital Pen Pressure Sensitivity Test click to visit website Pen Setti tting ji Second Button Right Button v Pressure sensitivity Q IL FirstButton Keyboard Keys v Support TabletPC Screen setting Monitor 1 Width 1440 Height 900 Main Advanced Setting Simulate Mouse F LeftHand WorkScopeandHotkey Pendisplay Calibration Device is disconnect La J cae ay Pressure sensitivity move the slider from left to right it can be used to adjust the sensitivity of the tip and the severity of the stroke when drawing which affects the change of the handwriting red box area When your computer is connected with two screens and use the extended mode you can choose the corresponding work area of the graphic tablet in the setup screen area green box area lll Pen Storage and Maintenance 1 Digital Pen 1 1 Storing the Digital Pen The digital pen should be stored in such a way that nothing touches the tip Prolonged pressure on the tip even a slight pressure can damage the ability of the pen to use the full range of pressure sensitivity If the pen will simply be unused overnight or for any other short period of time placing it in the included pen holder or horizontally on the desk is sufficient For long term storage or shipping the tip and battery should be removed 1 2 Replacing the Battery in the Digital Pen To install remove or replace t
7. ad HUION gt Graphic abe Windows User s Manual Gad HUION HUION FACEBOOK HUION WEBSITE Huion Building Hi Tech Park Shifeng ShenZhen P R China Support service huion cn www huiontablet com Address Tel 86 755 61537861 www huion tablet com FE Ce X service huiontablet com B CONTENTS l General Information _ T OvemMieWw Gecee26e5e0 eee EA A es ee a Z 2 Pen Tablet Functions 3 System Requirements 4 Installing the Driver Software on Windows 5 Hardware Installation 6 Verifying Hardware and Driver Functions 7 Usage libs sena 42s bere a a a E Driver Interface Introduction Control Interface cietieesn52eo4e eee a ee ee eee eee 2 2 Digital Pressure Sensitive Pen Settings __ 2 1 Key Functions 3 Workspace and Shortcuts Settings Sd a a PE 3 1 Workspace Settings 3 1 1 Funcion Shortcut Function Settings Ss ii 3 1 2 Express SHOMCUL Function Seltihngs sue 3 2 No Shortcut keys Workspace Settings
8. he battery in the digital pen perform the following steps a Unscrew the top half of the pen from the bottom half The junction is at the upper edge of the rubberized grip portion of the pen b Allow the old battery to fall out of the top half of the pen Dispose of the battery in accordance with local regulations c Insert a new AAA alkaline battery included in the top half of the pen The positive lead should be visible in the open pen half so that it makes contact with the bottom half when the pen is reassembled d Carefully line up the threads of the bottom and top halves of the pen and screw it together Take care not to cross thread the pen because the plastic threads can be easily damaged Screw the pen together firmly but not too tightly Power ON OFF Unscrew Unscrew cc Cathode upward Button2 Anode downward Button1 Pen tip 1 3 Replacing the Pen Tip If the pen tip needs replacing or removal due to long term storage perform the following steps as applicable a Open the pen holder and remove the metal Pen Clip b Position the Pen Clip over the exposed portion of the pen tip Squeeze the clip with your fingers to provide a firm grip on the tip c Pull gently until the tip is completely removed d Take a replacement tip out of the pen holder and gently insert it into the pen until it is fully seated into place e Use the Pressure Test dialog in the driver utility to test the operation of the newly re
9. l blink slowly This happens either when pen tip is hovering or placing within the working area which above the tablet 4 When you press a button on the pen barrel the LED will be lit up 5 Hovering and moving the pen or the mouse in the working area will cause the cursor on the screen to move accordingly Note After the tablet s device driver has been properly installed a small tablet icon Gj will appear in the system tray which is normally at the lower right corner of the screen 7 Usage Tips 1 Double tapping When you double tap with the digital pen equivalent to a double click with a mouse try to keep the pen tip away from the tablet s surface or at least try to lift the pen tip as fast as possible before the second tap 2 Storing the digital pen To store the pen make sure the pen tip does not touch anything and especially do not let the pen stand in a cup or pen holder with the tip down Even though the possibility is low constantly put stress on the pen tip might damage precise configuration of the pen Place the pen in a pen holder or turn the pen tip pointing upward or horizontally with the pen tip free of any pressure by other objects 3 Using a pen without an ordinary mouse You may install the digital pen digital mouse and normal mouse in your computer at the same time and you can also remove them to a different computer as well However only one device is able to work at a time Do not use more than tw
10. o devices at the same time in case the screen cursor is jittering or not moving ll Driver Interface Introduction 1 Control Interface Pen Setting i Second Button Right Button Pressure sensitivity I eas Keyboard Keys Support TabletPc Screen seting Monitor 1 Width 1440 Height 900 Main Advanced Setting Simulate Mouse F LeftHand Work Scope and Hotkey Pendisplay Calibration When you double click the driver tablet icon f which normally appears in the system tray at the corner of the screen you will see the control panel pictured above It will display driven related information Controlling the panel by digital graphic tablet can set up functions for the button of the digital pressure sensitive pen regulate the pen s pressure sensitivity 2 Pen Buttons Settings Pen Setting i Second Button Keyboard Key ae Cat shia IL First Button Keyboard Key ExpressKey K1 Left Button Middle Button Keyboard Keys oe Keyboard Keys Monitor 1 Widti None Button 2 1 Key Functions oc a III You can set any Mouse functions for the digital pen as the above Picture Selecting its Left Button Middle Button Right Button Keyboard Keys None Button on the corresponding right drop down menu of the Second Button First Button you can achieve the digital pen button function settings Note 1 Left Button Middle
11. or instance 4 Double click the Setup exe in the folder where you unzipped the file Question 2 The tablet cannot work How can do Answer Please follow steps as showing below 1 Please pull off the tablet s USB plug from the computer 2 Remove the Tablet driver from the system 3 Re connect theTablet s USB to the computer 3 1 Check whether the tablet s LED is blinking or not If the LED is unlighted it means your tablet is faulty 3 2 Test your wireless rechargeable pen on tablet working area if it can work as a mouse which means the hardware is OK If it does not work please use the tip of the pen to wake it up 4 You can download the latest version of driver directly from our website www huion tablet com 5 After installing the new version of driver the system will require you to restart your computer 6 6 After restarting your computer on bottom right of the screen you can find the tablet icon within there 1 If you can t find the tablet icon amp on the bottom right of the screen it means the driver fail in startup which might be due to incompatibility 6 2 Check from My Computer gt Properties gt Hardware gt Device Manager if an exclamation mark occurs it means the installed driver of tablet is incompatible with the windows system If you have this problem please contact us for more service 7 By clicking the tablet icon amp on the bottom right of the
12. placed tip 2 Rechargeable LI ION Battery amp Tip Rechargeable LI ION Battery 1 Tap on any surface with the tip of the pen to wake it up Charging port 2 It will auto sleep if not used for a period of time Notice if the reading height Plug in USB cable and charging become lower and the line is X unstable it means you have to charge y The LED indicator flashes during charging when it is out of flashing it finished charging charging time about 1 hour Charging the rechargeable pen tip A Pull out the pen tip from rechargeable pen by using a pen Clip that contained inside the pen holder Normal Pen Clip USB Charging port Pen Tip y Pen Clip OQ ha O B Push the pen tip into the rechargeable pen and make sure fit it up to the end properly Gently unscrew the pen holder in a counterclockwise direction you will see one pen tip replacement tool amp 4 spare pen tips inside The pen tip replacement tool and 4 pen tips IV Question amp Answer Question 1 How can get the update software Answer You can download the new driver from our website 1 Uninstall your old driver Click Start All Programs gt TABLET Uninstall 2 Download the latest version of driver in the download section and save it into your hard disk 3 Unzip the file in a folder on your hard disk with Windows built in unzip utility or a program like Winzip f
13. rea SoftKey key sett Area A Express sett Area B The work area Area C Full Area Softkeys Enable Softkey Disable ings Softkey has three sett Area D IC The graph the work area ion will be disabled in is key the key funct select th isable Sofkeys D in the C area ited Im IS tablet s work area Softkeys Enable select this key the function shortcut keys will be enabled in the work area of the graphic tablet Full Area full range selected graphic tablets work area will be expanded to Zone A plus Zone C soft shortcut key function is disabled Warning Some models have no Express Key or SoftKey functions please pay a attention 3 1 1 Softkey Settings only for some model of graphic tablet with hotkeys Click any softkeys to enter into the Softkeys function setting screen pictured above the corresponding shortcut is from S1 S16 of 16 soft shortcuts Warning Some models graphic tablet have different number SoftKey please pay a attention 3 1 2 Express key Settings only for some model of graphic tablet with hotkeys Click any Express keys to into enter the express keys function setting screen pictured above the corresponding shortcut is from K1 K8 of 8 express shortcuts Warning Some models graphic tablet have different number Express Key please pay a attention 3 2 No Shortcut keys Workspace Settings only for some model of graphic tablet without shortcut
14. s Vista Windows 7 Windows 8 Windows 10 4 Installing the Driver Soft ware on Windows For Microsoft Windows Vista Windows 7 windows 8 and Windows 10 operating systems 1 Insert the Driver CD into the CD ROM drive and wait for the main installation screen to appear 2 The main installation screen should appear automatically or you can manually start the installation by opening My Computer CD DVD Rom then click on the Setup program 3 When installing the driver follow the installation instructions on screen 5 Hardware Installation Connecting a tablet with USB interface into the PC after the driver installation is finished After connecting a pen tablet into the PC you will see a small tablet icon HG appears in the system tray which is normally at the lower right corner of the screen G Verifying Hardware and Driver Functions G 1 USB wired graphic tablet The following picture refer only to H610 the picture of different models will be a difference Indicator Softkey Oey ECan Onn en ie Express key Second Button First Button Active area Pen tip 6 2 wireless graphic tablet 1 Dual working modes wired amp wireless wireless distance can reach 20 meters in open space The following picture refer only to W58 the picture of different models will be a difference Wireless Pen Tablet m Power ON OFF LED indicator Working area Al Button2 Button1 V Pen tip 2
15. screen you can test the pressure sensitivity to see whether the pen pressure function works or not If you do not have the pen pressure it means the pen might be faulty Please see Chapter 2 Section 6 Pen Tablet Configuration for more information Question 3 The LED of tablet is blinking continuously Answer It means that the USB port of your PC has a bad connection or power is not stable Please re plug in your USB dongle again If it is still not working please change to another USB port Question 4 Why does the LED flash when tapping the tablet by pen Answer Please check if the distance is too far between dongle and wireless tablet or it s because of the working environment If so please auto bind the dongle again If tablet can t bind to dongle please kindly send it back to where you purchased for repair Question 5 How to deal with the drawing delay in painting software Answer Please do some steps in control panel and grpahic driver panel 1 uncheck the Suppout Tablet PC in grpahic driver panel 2 turn off the Flicks in Pen and Touch in control panel 3 cancel the Press and Hold in Pen and Touch in control panel enDi Pen Setting 1 OW E gt Control Panel All Control Panel Items gt X 4 Search Con P ug roomy opoo amp Keyboard Lenovo Power Controls 6 Lenovo s Notebook Fingerpi P Mouse 2 One atiorr sea Icons Pen and Touch
Download Pdf Manuals
Related Search