User Manual for Installation & Use of Mobile DVR (SD
Contents
1. anywhere under direct sunshine dust moisture corrosion strong magnetic field or mechanical vibration impact Copyright protection for video recording or monitoring please ensure no breach of relevant rights of third party in case of no permission from our company or the proper entrusting unit any amendment and alteration to this device may result in damage making inconvenience to use ll Front rear Panel Definitions 1 Front Panel Definitions Single SD Card with Wi Fi j PWR CH4 CH2 SD2 SESA SMSS a ERR CH3 CH1 SDI REMOVE1 SD CARDI 1 LED Indicator Light PWR Power input status indicator LED light indicates the system is charged ERR Error indicator LED light on indicates SD card fault LED light off indicates SD card is working normally CH1 CH4 Video indicator Light on indicates video input is normal Light off indicates video input is lost CH1 System upgrade indicator LED light flashes system is being upgraded SD1 SD2 SD card indicator light LED light on SD card uploaded successfully LED light off SD card uploading failed LED light flashes a video is being recorded IR Infrared receiver used for receiving remote control signal 2 SD Card Remove amp SD Card Slot REMOVE1 REMOVE2 SD card remove button When the device is in operation long press the stop SD card reader button for 3 seconds the SD card indicator light will go off and the SD card can2. button on the remote control upon display of the four monitor screens then the device status information will be displayed 2011 09 05 09 12 23 GSENSOR X 0 22g Y 0 36g Z 0 04g GPS MODULE EXIST 3G MODULE EXIST LONG 113 66 4790 E SIM EXIST LAT 22 330 3640 N SIGNAL 27 y 0 OOMILE DIALUP OK SATELLITE 4 12 IP 172 21 74 161 ALTITUDE DEVICE NO ONLINE NO 37M rp oD WIFI MODULE EXIST AP NO CENTER 156 24 128 160 SIGNAL 0 PORT 5678 Users may confirm the device GPS status 3G dial status Wi Fi connection online offline and other information via the status information Vi Frequently Asked Questions 1 Q Why is 3G transfer of data not possible A The following are the possible reasons why 3G transfer of data is not working 1 2 3 4 5 3G antenna not connected SIM card not inserted The wireless related settings in the setup menu are not correctly set For example wireless dial up not switched on 4G protocols setting incorrect serial port setting not matching etc The settings on the setup menu related to the central server are not correctly set For example the central IP setting is incorrectly set The configuration parameters on the PC side are not correct For example the gateway router on the PC side does not have any proper port mapping 6 The playback tool on the PC is not on 7 The server software has not been running 2 Q W
3. mean while Save the setting in the end 6 Enter the Power Setup The normal setting is ignition mode For delayed power on off the delay time is 30 minutes up to customer requirement Save the setting in the end 7 Enter the Network Setup NETWORK SETUP LOCAL SETUP IP ADDRESS NETMASK GATEWAY MAC CENTER SETUP TYPE fe 1 DOMAIN www 145 Ci 3G SERVER WIFI SERVER SAVE Local network ignore this item during use of 3G function Setting of central network Type set as IP Domain name This item is effective only when it is registered by domain name e g www 123 com Those users using fixed IP can ignore this item Center IP setting as the fixed IP address in the server external network When the Connect to Internet is set on the same address is used for registration Port 5678 as default setting requiring to be set with port mapping at router Wi Fi center Setting as the IP address in the server Wi Fi internal network Port 5678 as the default port 8 3G Setup 3G SETUP 3G TYPE APN CENTER NO USER NAME PASSWORD LINK MODE TRIGGER NO 1 TRIGGER NO 2 3G set as on Type set the type of Wi Fi module WCDMA China Unicom EVDO China Telecom or TD China Mobile Refers to the 3G format of the purchased model Access point set the data access point by default within China Username amp password set the username amp password of Wi Fi service by default wi
4. User Manual for Installation amp Use of Mobile DVR SD Card Before connection and use of this device please read carefully the following statement and keep it for use in future Attentions Power supply Power supply to this device is DC8 36V applicable to vehicles under 12V and 24V power supply so please confirm the power supply voltage of your vehicle before installation the external output voltage of this device is DC12YV only for power supply to video recorder so please don t connect to any other device not specified or allowed for use to this device in case of long time of no use please power off the device in order to extend its service life Safety This device is for indoor use please don t put it under moisture in order to prevent from short circuit or electric shock external wires of this device shall be provided with sufficient interval and fire retardant sleeve pipe as protection so as to ensure the wires are not bent or leaked due to vibration or aging in case of any breakdown professional technicians must be invited for repair or you can contact the distributor rather than self repair Installation position Select a proper position for installation which must be resistant to splashing water or water drop with good ventilation far away from heat sources and with relatively weak vibration It is prohibited to install the device in the following positions near to heat sink generator or other heat sources or
5. auses 1 Settings on the alarm menu setup incorrect for example the function of specified alarm input is not switched on or the alarm signal level setting is incorrect 2 The alarm input cable is not properly connected or not connected at all 3 The signal level of the alarm triggering source is incorrect 6 Q When the device is switched on why does the power light not light up A The following reasons can cause the power light not light up 1 The voltage is not within 8V to 36V range 2 The power fuse on the power cord input line has burnt out 3 The ignition signal is not connected 7 Q Why does the ERR light lights up A Under the following conditions the ERR light lights up 1 SD card and hard drive not inserted or the SD card and hard drive have been inserted but the system partition is not valid so the device cannot recognize them 2 Read and write error of the hard drive 3 Microcontroller working abnormally 8 Q Why does SD card light not light up or flash A The SD card light has 3 states off on and flashing and they convey following messages respectively Off The SD card has not been inserted or the device cannot read the SD card On The SD card is present but is not in the currently recording disk Flashing The SD card is present and is also in the currently recording disk 9 Q Why are some channel images like black screens A The phenomenon that some channel images are like black scre
6. be taken out safely if the SD card has not been taken out in time it will be reloaded automatically within 15 seconds SD card slot for storing video data or upgrading software 2 Rear Panel Definitions PWR Power port GPS GPS antenna port WIRELESS 3G antenna port ETHERNET Ethernet port ALARM IN OUT Alarm input output port VI VO AI AO1 Video input Video output port Audio input Audio output port Ill Installation Diagram The following is an indicative diagram for bus actual installation will depend on the actual vehicle and configuration CAM3 MDVR CAM2 IV Wiring Diagram In accordance with the following diagram properly connect external devices such as the DVR power cable antenna and video recorder GPS ANT PICKUP CAMERA1 2 3 4 MONITOR LOUDSPEAKER WIFI ANT rs 3G ANT 5 0 A AS Na Waa Nana NZ 1 2 3 4 WIFI VEHICLE KEY ACC POWER CABLE 5 __ Sr nae Gee BA BA ial SWITCH YELLOW ACC y a ra A C 7 i i os His l gt Vol 1 Sajos bella fa bd FM feed g RED z BEE BEP E EE RE BLACK ETHERNET ALARM IN OUT VI VO AI A0 vn ER vM AOUTI BATTERY i AINI a A V INPUT CABLE EXTENSION CABLE m paragem WITC H aim y E A a Oo m a Baas fo CONNECT TO AL2 RX2 yy 932CONVERTER Fa Dy PTZ lt a AL3 a it 232 TO 485 CONNECTION METHOD BACKING lt TRIGGER LINE CONNECTION METHOD V Fast Setup Make sure all the external devices such as
7. ens is due to the following possible causes 1 This channel is not connected to the video 2 The camera connected to this channel is damaged or not working properly 3 The cable connecting to this channel is not connected properly or damaged 10 Why is there no GPS signal A There are following possible causes why there is no GPS signal 1 The GPS module is not connected or there s no signal inside 2 The GPS interface is damaged 3 The GPS module is damaged 11 Q Why is the remote control not able to remote control A The remote control cannot remote control because of the following possible causes 1 There is no battery in the remote control or out of battery 2 The remote control is damaged
8. hat should first be done when problems related to wireless module are experienced A Go straight to the screen information display or to the system information page Press F1 on the remote control to check the dial up status whether the SIM card is present whether wireless module exists and whether the antenna is properly connected 3 Q Why is the device not recording video A The following causes can lead to the device not recording video 1 The recording mode is set incorrectly If it is set to be the alarm recording mode but no alarm has been triggered in that period if it is set to be timer recording but the current time is not within the time set 2 Check the disk space If the disk space is less than 500M and automatic superimposed recording has been switched off at the menu setup then recording will stop 3 The ERR light on the front panel lights up Check the system information the dish space may indicate as 0 check if the disk drive has been inserted or if the disk drive has been formatted 4 Onthe menu setup all the 4 channels indicate they have been turned off 4 Q Why is there no audio sound in the recording A There are following possible reasons why there is no audio sound 1 In the audio settings the sound is not turned on 2 The audio output cable is not connected or there is connection error 5 Q Why is the alarm not triggered A The alarm is not triggered because of the following possible c
9. the power supply camera display etc are well connected to the DVR Insert SIM card and SD card and then turn on vehicle key switch start the DVR The Power indicator light turns on and images show up on the display after the system starts And it can be set by remote control 1 User Login Press ENTER on the remote control to enter the menu Input the administrator password to set menu The default general user password is 000000 administrator password is 888888 2 Enter the Main Menu Select System Setup by remote control press OK 3 Enter the System Setup Select the Basic Setup by remote control press OK 4 Enter the Basic Setup BASIC SETUP DATE TYPE TIMEZONE DATE IDLE TIME DEVICE NO MAIN INFO NUMBER NAME REMARK As the device number company name plate number driver name line number are set up make sure the time setup and save the settings NOTE The device number must be unique It can t be the same device number for any two devices 5 Enter the Recording Setup The normal setting is PAL format China video recording as default mode D1 resolution default code rate Voice recording will be on in case of audio input or else closed Automatic coverage is applicable to normal video recording or all video recording Segment time is 30 minutes as default Frame rate is normally set as 15 25 frames depending on capacity of SD card Video channels not required should be closed at the
10. thin China Linking mode set as normal linking Trigger number use a mobile phone to trigger device dial or stop dial up to 2 mobile numbers can be set Attention At trigger mode it is ok to dial the phone to trigger dial but the 3G card should be opened with call number display or SMS via the phone to trigger or stop dial Contents for SMS trigger should be as follows 1 DIAL 11 trigger dial 2 DIAL OO stop dial SMS can also be used for some parameter setting or device reboot 1 RBT reboot the device Save the setting in the end 9 Wi Fi Setup It is required when the user uses the Wi Fi function WIFI SETUP WIFI ENCRYPT ENCRYPE TYPE FES GATEWAY SUB MASK SSID ONLO NDE Wi Fi On Encrypt On Encryption type WEP by default IP address gateway and subnet mask must be identical to the segment of Wi Fi hot spot SSID and security key must be identical to the setting of wireless router Save the setting in the end Attention Please change the IP segment in the previous LAN setting to be void so as to ensure no conflict with the Wi Fi segment Save the setting in the end 10 Format SD card Enter Disc Management under the menu of Management Tools format SD card After formatting the SD card will enable normal writing of video recording That is all the basic setting VI Status Menu After device installation and setting power on the device and press the F1
Download Pdf Manuals
Related Search