User Manual
Contents
1. 2 1 System Setup of IPC 611 2 1 1 Attaching the handles and removing the top cover The handles for the front panel are in the accessory box To install the handles simply secure them to the front panel with the screws provided Please remove the chassis cover by releasing two screws which are on the rear of chassis 2 1 2 Adding and removing disk drives Undo the four screws of cushion to release disk enclosure from chassis and then you could move disk enclosure out of chassis to install or remove the necessary 5 25 and 3 5 disk drives 2 1 3 Chassis front panel sections Refer Figure 2 1 to find system power LED and HDD LED on front bezel power switch and system reset which are behind the door Figure 2 1 Front panel section 2 1 4 Momentary switch Use momentary switch and by way of ATX PS_ON function to turn on system ATX power supply Please use system shutdown to turn off system power automatic or press momentary switch for more than 5 seconds to turn off system power 8 IPC 611 User Manual 2 1 5 Replacing cooling fan and filter Refer Figure 2 2 to find location of system cooling fan and filter Please replace system cooling fan if it is defective replace or clearing filter when the dust is too heavy Figure 2 2 Cooling fan amp filter ll d Appendix A Exploded Diagrams A 1 IPC 611 Exploded Diagram Figure A 1 exploded diagram 11 Appendix B Safety Instructions D MANS 14 152. 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This eguipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the eguipment is operated in a commercial environment This eguipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his her own expense The user is advised that any equipment changes or modifications not expressly approved by the party responsible for compliance would void the compliance to FCC regulations and therefore the user s authority to operate the eguipment Chapter 2 System Setup If you want to connect any USB device or PS 2 keyboard to the system you could use the front accessible USB amp PS 2 connectors The system LED display is on front of door cover and shows system power status system voltages and HDD activity Power switch and system reset are behind the door
3. 16 17 18 19 20 21 Read these safety instructions carefully Keep these instructions carefully Keep this installation reference guide for later reference Follow all instructions Clean only with a dry cloth Disconnect this equipment from any AC outlet before cleaning Do not use liquid or spray detergents for cleaning Use a damp cloth For pluggable equipment the power outlet must be installed near the equipment and must be easily accessible Keep this equipment away from humidity or water Put this equipment on a reliable surface during installation Dropping it or letting it fall could cause damage The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS Make sure the voltage of the power source is correct before connecting the equipment to the power outlet Position the power cord so that people cannot step on it Do not place anything over the power cord Protect the power cord from being walked on or pinched particularly at plug convenience receptacles and the point where they exit from the apparatus All cautions and warnings on the equipment should be noted If the equipment is not used for a long time disconnect it from the power source to avoid damage by transient over voltage Never pour any liquid into an opening This could cause fire or electrical shock Never open the equipment For safety reasons the equ
4. A 1 PCA 6114P10 B 32 bit 14 slot 2 ISA 10 PCI 2 PICMG 1 PCA 6114P12 0B1 32 bit 14 slot 1 ISA 11 PCI 1 PICMG PCL 1 PICMG 1 PCA 6114P12X Al 64 bit 14 slot 1 ISA 11 PCI 1 PICMG PCI 1 PICMG 1 PCA 6113P4R 0C1 32 bit 13 slot 7 ISA 4 PCI 2 PICMG 1 PCA 6113P7X 64 bit 13 slot 4 ISA 7 PCI 2 PICMG 1 1 5 Dimension Diagram l nn T Unit mm inch Figure 1 1 Dimension diagram of IPC 611 1 6 Safety Precautions Warning Always completely disconnect the power cord from your chassis whenever you work with the hardware Do not make connections while the power is on Sensitive electronic components can be damaged by sudden power surges Only experienced electronics personnel should open the PC chassis Caution Always ground yourself to remove any static charge before touching the motherboard backplane or add on cards Modern electronic devices are very sensitive to static electric charges As a safety precaution use a grounding wrist strap at all times Place all electronic components on a static dissipative surface or in a static shielded bag when they are not in the chassis Caution These servicing instructions are for use by qualified service personnel only To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so 4 IPC 611 User Manual FCC This device complies with the reguirements in part
5. IPC 611 Series 4U Rackmount Industrial Chassis User Manual Copyright Advantech Co Ltd copyrights this documentation and the software included with this product in Nov 2005 All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable However Advantech Co Ltd assumes no responsibility for its use or for any infringements of the rights of third parties which may result from its use Acknowledgments Intel Pentium and Celeron are trademarks of Intel Corporation IPC 611 PCA 6113P4R 0C1 PCA 6113P7X PCA 6114P4 C PCA 6114P7 0D2 PCA 6114P10 B PCA 6114P12 0B2 PCA 6114 0B 1 PCA 6114P12X A1 are trademarks of Advantech Co Ltd All other product names or trademarks are the properties of their respective owners On line Technical Support For technical support and service please visit our support website at http www ad vantech com support i IPC 611 User Manual A Message to the Customer Advantech customer services Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial envir
6. esssnee 11 A 1 IPC 611 EXPLODED DIAGRAM cccccccccsssscceceeeeeenees 11 Figure A 1 IPC 611 exploded diagram 11 APPENDIX B SAFETY INSTRUCTIONS ccssssccsssseccsssceeeses 14 vi IPC 611 User Manual Chapter 1 Information 1 1 Introduction IPC 611 is a 4U height 14 slot rackmount IPC chassis designed as a core building block for mission critical applications This rugged all steel chassis meets the EIA RS 310C 19 rackmount standard IPC 611 comes with shockproof and front accessed driver bay three 5 25 amp one 3 5 This chassis supports a versatile 14 slot full length passive backplane or an ATX M B form factor one front accessible easy maintenance cooling fan which provides abundant cooling The flexible mechanical design provides PS 2 size single or redundant power supply through a power supply bracket replacement A wide range of standard computing peripherals can be integrated with the chassis to meet various application developments under mission critical environment 24 hours a day 7 days a week 1 2 Specifications Table 1 1 Specifications of IPC 611 Front accessible Internal Drive Bay 2 l 3 25 3 Cooling Fan 1 85 CFM each and front accessible Air Filter Yes Miscellaneous Front LED Indicator LED display for power on and HDD activity Rear panel D SUB 9 pin and 25 pin openings Environment Operating Non Operati
7. iginal purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of purchase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech assumes no liability under the terms of this warranty as a consequence of such events If an Advantech product is defective it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps Step 1 Collect all the information about the problem encountered For example type of PC CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any on screen messages you get when the problem occurs Step 2 Call your dealer and describe the problem Please have your manual product and any helpful information readily available Step 3 If your product is diagnosed as defective obtain an RMA return material authorization number from your dealer This allows us to process your return more quickly Step 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card a
8. ipment should be opened only by qualified service personnel If any of the following situations arises get the equipment checked by service personnel a The power cord or plug is damaged b Liquid has penetrated into the equipment c The equipment has been exposed to moisture or rain d The equipment does not work well or you cannot get it to work according to the installation reference guide e The equipment has been dropped and damaged f The equipment has obvious signs of breakage DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW 20 C 4 F OR ABOVE 60 C 140 F THIS MAY DAMAGE THE EQUIPMENT Do nat block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves 14 IPC 611 User Manual 22 23 24 25 26 27 28 or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or ground plug A polarized plug has two blades with one wider than the other The wide blade is provided for your safety When the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Only use attachments accessories specified by the manufacturer Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus Whe
9. n a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lighting storms or when unused for long periods of time To Reduce The Risk Of Fire Or Electric Shock Do Not Expose This Apparatus To Rain Or Moisture Apparatus shall not be exposed to dripping or splashing and objects filled with liguids shall not be placed on the apparatus Only used with the battery which specified by manufacturer The sound pressure level at the operator s position according to IEC 704 1 1982 is egual to or less than 70 dB A DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein 15 16
10. nd a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service Step 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer Part No 2006061100 1st Edition Printed Nov 2005 iv IPC 611 User Manual Contents CHAPTER 1 INFORMATION cccssssscssssscccsssccesssccscssseccsessnseces 2 1 1 INTRODUCTION ccccccccncnnnnnnonnnonononononononononononononononenonenenes 2 1 2 SPECIFICATIONS occcccccccccnonononononononononononononononononononenenenes 2 Table 1 1 Specifications of IPC 611 ncnenenenee 2 1 3 DIMENSION DIAGRAM ovcooooonncnnccconnnnnononcncononnanononcnccninnnnns 3 Figure 1 1 Dimension diagram of IPC 611 4 1 4 SAFETY PRECAUTIONS cc cccccccecsesssseceeececsesssseceeececeenees 4 1 5 PASSIVE BACKPLANE OPTIONS cccccccecsesssseceeeceeeenees 3 Table 1 2 Passive Backplane Options 3 1 6 POWER SUPPLY OPTIONS ococcccccconncononononccnonnnnanononccnonnnnns 3 Table 1 3 Power Supply Options s es 3 CHAPTER 2 SYSTEM SETUDP ccssssccsssssccsssssecssssscccsssscccssssscces 8 2 1 SYSTEM SETUP OFIPC 6 11 ooncnnccccccncccncononannnnnccncnonnnnnos 8 Figure 2 1 Front panel section osses 8 Figure 2 2 Cooling fan amp filter aseeseen 9 APPENDIX A EXPLODED DIAGRAMS 01 ssssccsssssccesssccessssc
11. ng Temperature 0 40 C 32 104 F 20 60 C 4 140 F Humidity 10 85 10 95 Vibration 5 500 Hz 1 Grms 2G Shock 10 G With 11 msec duration 30G 1 2 sine wave Altitude 10 000 ft 40 000 ft Physical Dimensions W x H x D 482 x 177 x 480 mm 19 x 7 x 18 9 Weight 14 kg 30 8 lb Compliance Safety CE compliant UL cUL approved 2 IPC 611 User Manual 1 3 Power Supply Options Table 1 2 Power Supply Options Model Name Watt Input Output Mini load Safety MTBF PS 250ATX Z 250W AC 115 230 5V 27A 5 V 0 5 A UL CB TUV ATX PFC Selected 3 3V O20A 3 3 V 0 3 CCC 12V 13A A 100 000 hours 12V 0 8A 25 C 5V 0 3A 5Vsb 2A PS 300ATX ZB 300W AC 100 240 5V 30A 5 V 0 1 A UL CB CCC TUV ATX PFC Full range 3 3V O28A 3 3 V 0 3 100 000 hours 12V015A A O25 C 12V 0 8A 5V 0 3A 5Vsb 2A RPS 300ATX Z 300W AC 100 240 5Vsb 2A 5Vsb 0 1A UL CCC CB TUV ATX PFC 1 1 Full range 5V 25A 5V 3A CE 3 3V 18A 3 3V01A 110 000 hours 12V 16A 12VO2A O25 C 12V 0 5A 5Vsb 0 1A 5V 0 5A 5Vsb 2A 1 4 Passive Backplane Options Table 1 3 Passive Backplane Options B P Model Name Slot per Segment ISA PCI CPU Segment PCA 6114 0B1 32 bit 14 slot 14 ISA 1 PCA 6114P4 C 32 bit 14 slot 8 ISA 4 PCI 2 PICMG 1 PCA 6114P7 0D1 32 bit 14 slot 4 ISA 6 PCI 3 PICMG 1 PCI IS
12. onments Whether your new Advantech eguipment is destined for the laboratory or the factory floor you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known Your satisfaction is our primary concern Here is a guide to Advantech s customer services To ensure you get the full benefit of our services please follow the instructions below carefully Technical support We want you to get the maximum performance from your products So if you run into technical difficulties we are here to help For the most freguently asked guestions you can easily find answers in your product documentation These answers are normally a lot more detailed than the ones we can give over the phone So please consult this manual first If you still cannot find the answer gather all the information or guestions that apply to your problem and with the product close at hand call your dealer Our dealers are well trained and ready to give you the support you need to get the most from your Advantech products In fact most problems reported are minor and are able to be easily solved over the phone In addition free technical support is available from Advantech engineers every business day We are always ready to give advice on application reguirements or specific information on the installation and operation of any of our products iii Product warranty Advantech warrants to you the or
Download Pdf Manuals
Related Search