QUICK376D
Contents
1. meaning of the digit displayed Note X represents original working mode digit Z warning The heater and Soldering tips will be seriously oxidized or damaged when working with a high temperature So please choose the working mode carefully and try to operate with a lower temperature if possible SECTION 12 Sleeping If sleeping and working mode are selected and the unit is not used for 20 minutes the power to the heating element will be decreased and the display shows This state is sleeping mode When the unit is in sleeping mode the tip temperature will decrease to 200 C If the set temperature is more than or equal to 200 C or 50 C If the set temperature is less than 200 C and remain the temperature until resuming the unit To resume soldering there are several ways as follows 1 Turn the power switch OFF then ON 2 Hit any button 3 Take up the iron Hand Assembly If the unit is not resumed more than 40 minutes after 1t comes to sleep the power supply will be shut off automatically and the display window will not show anything Page 17 Working Modes Table AVAILABLE AUTO HANDLE MODE TEMPERATUE MODE FOR MAIN SLEEPING amp SWI RANGE UNIT TCHING OFF High frequency soldering 200 C 420 C 60W Station iron High frequency soldering 200 C 420 C 90W Station iron High frequency special very 60 90W 200 C 420 C large Station High frequency tweezers 50 C 600 C 90W Station stripp2. Remove the broken fuse and replace it with a new one 4 Fix the fuse holder SECTION 18 Replaceable Part Oo frie 2 rewintenenvow 3 J oisinctensow 4 Prestertibeasensiy 0a oen 5 esterase 046m osm Prater sen 06m orom 7 Peeters 06m 2m O 5 ester asenby Oden oram 9 Prater asenoy 06m etm ww a o eee yam oao LRT Assy 08 aww Feeder Tube Assembly 0 8m 91 0mm C Fee nie noe 08m o2 O C e Piet Ascot 08m ata O Page 22 SECTION 3 Character Iron soldering adopts high frequency heating K type sensor rapid heat and recovery speed to realize lead free solder Many kinds of soldering tips with long service life can be optional and easy to use Digital display Button adjustment digital calibration and design with automatic sleep function Auto and Manual Feeding Mode optional and the times adjustable Feeding Speed and Feeding Length and Feeding Interval Time adjustable further more it is designed with Returning function to reduce solder wire consumption Two kinds of Feeder Tube can be chose and easier and more convenient to using Long tube with Manual Touch Switch is suitable for active soldering Short tube is suitable for fixed soldering Both of Pedal switch and Manual switch can be use It is used as Lead Feed Soldering Irion ESD safe by design to avoid damaging sensitive element because of static SECTION 4 Panel Picture Display Window Temperature Button Digital Swit
3. off the Power supply when not use Clean the soldering tip with a cleaning sponge and then covered with new tin Repeat above steps when use it again 5 Replace soldering tip if it is twisted or eroded badly Page 19 SECTION 13 Temperature Calibration The Soldering Iron s temperature should be recalibrated after replacing the iron or heating element or nozzle every time The unit adopts digital calibration mode and the revision value is input by pressing button to make the adjustment simply and quickly Method of recalibrating temperature Use the thermometer to calibrate and it is precise comparatively Calibrate by using thermometer l 2h Set the unit s temperature to a certain value When the temperature stabilizes measure the tip s temperature with thermometer and write down the reading Press x button not loose and press the A and V button simultaneously the unit enters into calibrating temperature mode At the moment the 100 s digit of LED display temperature is flashing Press the A and V button to select the value and press button to select the digit Input the reading of thermometer and inputting method is the same as Set temperature normally Press button after inputting Here the whole calibration operation has been finished If the temperature still has deflection you can repeat calibration in accordance with above steps We recommend to use
4. password is initial While setting the temperature normally the heating element is off If the button is pressed less than one second the present temperature setting will be shown for two seconds and then the display will return to showing the tip temperature A and VW are choice button for value is choice button for digit Example 400 C to 350 C l 400 J Press button once UU Press the button and hold it down for at least one second The left most digit the 100 s digit in the display will flash This indicates that the station is in temperature setting mode and that the 100 s digit can be adjusted Page 11 Press Aor 7button wl QO a ai JE Press button once Select the desired value for 100 s digit Use the A or Y button will change displayed value as follows aaa 0a 3 lt gt gt 7 Press the button when the desired value is displayed This will cause the middle digit the 10 s digit in the display to begin flashing Select the desired value for the 10 s digit Using the A or Y button will change the displayed value as shown below EEA Press the button The right the 1 s digit will then begin flashing to indicate that the 1 s digit can be set 7 fF 450 i V7 Press button once Sob Z Select the desired value for the 1 s digit U
5. set as 1 the interval time 1s 0 3 second When it is set as 2 the interval is 0 6 second When it is set as 9 the time is longest with 2 7 seconds Press the Interval Time Switch to choose the digit The range is 0 second to 2 7 seconds 4 Feeding Mode setting Press the Feeding Mode Switch to choose suitable digit Feeding Mode is designed with one digit and the setting method is the same as above The digital match function as follow 0 Manual Feeding 1 Auto Feeding once 2 Auto Feeding twice 3 Auto Feeding three times 4 Auto Feeding four times 5 Auto Feeding five times 6 Auto Feeding six times 7 Auto Feeding seven times 8 Auto Feeding eight times 9 Auto Feeding nine times After each feeding it has returning 5 Returning Time setting Press Returning Switch to set the match digit in accordance with working demand Returning Time is designed with one digit 0 to 9 denotes 0 second to 0 9 second The resolution is 0 1 second namely each digit denotes 0 1 second The returning speed is fixed with 360 s Example When the digit is set as 1 the returning time is 0 1 second and the returning length is 2 8mm The digit is set as 2 the returning time is 0 2 second and the returning length is 5 6mm When the digit is set as 9 the returning time is 0 9 Page 10 Input New Password 1 When display window is showing Ob press button and shows It indicates the unit comes into inputting new password state
6. Pressing A or Y button will change displayed value See set temperature normally Repeat the new password 2 When three digits are selected press button the display window shows 3 Ifthe password is the same as last time the changed password is OK The new password is stored into the internal memory 4 If the password is not the same as last time and the display window shows E the station will need to rewrite new password see the last 8 9 step The changing of password is finished until the lately two passwords are identical Z note The word of password is from 0 to 9 ten words If not the changed password is unsuccessful SECTION 11 Set Working Mode The unit is design with many working modes When the unit leave factory working mode is set as seven mode User don t change this working mode optionally during using SECTION 10 Set Password Page 15 The initial password in station s memory is 000 The setting temperature is admitted in this state If need to restrict the setting temperature the password must be changed Enter into setting the password 1 Turn off the power switch Press and hold the A and V buttons simultaneously then turn on the power switch 2 Continue holding down the A and V button until the display shows O When the display shows the station is in parameter input mode Input Previously Password cea ca co 4 Pre
7. QUICK376D Self Feeder Soldering Station Operation Manual Thank you for purchasing a Self Feeder Lead Free Soldering Station Please read this manual before operating the unit Store this manual in a safe easily accessible place for future reference 9 A oy 42 232 224 gt 216 et po P12 o 2 i y 63 A 63 4 ia 03 4 y Zs Ws 2 y L EEE N N N y am D N Q Q ae sy tH oJ A amp J y Cr at 208 i amp b pa a EE LLU Li LE LL Lt LL N N N N y Jee SS Se AU Fy Ae Z gt E q Ss N 3 Q Q N e 9 a ii o y N N ee ee O gt O G GA ee iO A Eon i ae LL HT I Gmi N N Page 24 CAUTION e Appliance shall only be used with rated voltage and frequency Refer to the nameplate back of the unit e Don t use or stop the use if the appliance is damaged especially the supply cord Please avoid an abuse of the equipment use the appliance only in the described manner e The appliance is used in the room e Before replacing tip or storing the unit turn the power off and allow the tip to c
8. ch Power Switch Page 3 If the resistance value is not normal replace the heating element After replacing SECTION 5 Combination heating element please check as follow Choose match Soldering Tip in accordance with Soldering Point 1 Measure the resistance value between pins 4 amp 1 or 2 pins 5 amp 1 or 2 pins 6 amp 1 Choose Solder Wire Ring in accordance with Solder Wire diameter or 2 pins 6 amp 4 or 5 If itis not the heating element and sensor are touching Choose Feeder Tube in accordance with Solder Wire diameter This will damage the P W B Choose Guide Tube Assembly in accordance with Solder Wire diameter 2 Measure the resistance value a b and c to confirm that the lead wire are NOTE Please fix on Solder Wire diameter when purchasing the unit in not twisted and that the grounding wire is properly connected order to match Feeder Tube Assembly and Solder Wire ring exactly 3 To confirm that the clasp is clasped with heating element SECTION 6 Product picture and parts name sem No a Refer to the last page Handle Cover 0 i 12 Pin 6 Connector Metal 13 r i SECTION 17 Replaceable Part Main Unit Damageable part can be replaced by customers themselves 1 Replace Soldering tip Screw off the metal nut of Soldering tip anti clockwise and remove tip enclosure Page 4 Page 21 SECTION 16 Check and replace Heating Element Disconnect the plug and measure the resistance va
9. dering Station The Soldering Iron adopts high frequency heating rapid heat and recovery speed to realize lead free solder SECTION 2 Specification Working voltage of heating element 36V 400KHZ Range of temperature 200 C 480 C Temperature Stability eG Tip to Ground Potential lt 2mv Tip to Ground Resistance lt 2 Q Max Power consumption of unit 90W Motor Step Motor Feeding speed About 2 7mm s 27mm s 36 s 360 s Feeding Length 0 150mm Feeding Interval Time 0 2 7s Returning Time 0 0 9s About 0 25mm Speed 360 s Feeding Mode Auto 1 9 Manual 0 Dia of solder wire 0 5 0 6 0 8 1 0 1 2 1 4 1 6 mm Weight of solder wire usable lt 1Kg Roll Page 2 8 Restreanenbiy 8m oto Using on the bottom of Tip Using on the bottom of Tip Using on the bottom of Tip Using on the bottom of Tip Using on the bottom of Tip Guide Tube Assembly 1 6mm Using on the bottom of Tip 28 eter Tte 04609 oom OOOO 2 eter Tte 04609 osm a0 RsrTber06n okt at Retertate 0860 oka OOOO O a Traer 0860 ott OOO E oho e rearen oem OOO ooo s rears osam OOO Ooo E oktww st eter Tte 08m ota OOO C s Feiertte 080 okt OOOO o Reker Tte 08m otom O o Page 23 and Soldering tip Put a new Soldering tip on heating element and tighten nut Z Note To avoid scald replacing when it cools down 2 Replace Fuse 1 Pull Power plug out of Power socket 2 Take out the fuse holder on the rear side of the unit with screwdriver 3
10. er iron High frequency soldering 50 C 420 C 60W Station iron High frequency soldering 5 50 C 420 C 90W Station Yes iron High frequency soldering 200 C 480 C 60W Station iron High frequency soldering 200 C 480 C 90W Station iron High frequency soldering 200 C 420 C 60W Station iron High frequency 200 C 420 C 90W Station soldering iron High frequency tweezers or 60 90W 200 C 420 C using Station High frequency tweezers 50 C 600 C 90W Station stripper High frequency soldering 50 C 420 C 60W Station No iron High frequency soldering 5 l 50 C 420 C 90W Station No iron High frequency soldering 200 C 480 C 60W Station iron po e frequency soldering 200 C 480 C 90W Station iron Page 16 When turn on the power Switch the soldering Iron begin to heat up Temperature lamp is light In order not to be scalded please be careful when installing Make sure the power voltage in accord with working voltage of unit SECTION 8 Set Parameter 1 Feeding Speed setting Feeding speed is set with digital switch Press button on the digital switch and the match digit will increase by one step Similarly press button and the match digit will decrease by one step Feeding speed is designed with one digit 0 9 denotes the feeding speed is about 2 7m s 27m s Angle 36 s 360 s The resolution is 2 7mm s namely each digit denotes feeding speed is 2 7m s 36 s E
11. ion location of Guide tube and soldering tip 7 Adjust direction of soldering iron When adjust direction first unscrew the Nut of corresponding direction and then adjust Unscrew the Nut at the bottom end of Bracket assembly and turn around or rotate Bracket assembly can all adjust direction of Soldering Iron Finally tighten Nut after adjusting Unscrew two Nuts and on top end of Bracket simultaneously and turn around Handle clamping element can also adjust direction of Soldering Iron NOTE Please be careful not to break heating element when screw off black nipple to install connector If step on Pedal Switch or press down the red Touch Switch the solder wire can t be sent out automatically it needs to adjust feeding pressure Pressure adjusting screw Refer to parameter setting The Feeder tube can t be bended overly avoiding the solder wire block Page 8 1 If the display windows shows l press and hold the A or Y buttons simultaneously then the display shows x This indicates the unit comes into working mode setting state and pressing A or Y button will change displayed value as shown below in 0 gt 4 24 3 lt 4 lt gt 5 lt gt 6 lt gt 7 0 gt lt gt 2 lt gt 3 gt 44 gt h4 6 4 gt 7 2 After selecting the working mode press down The working mode is stored into the internal memory Please refer to the Working Mode Table for the
12. lue between the connecting plug pins as follows If the values of a and b are outside the below value replace the heating element sensor and or cord assembly If the value of c is over the below value remove the oxidization film by lightly rubbing with sand paper or steel wool the points as shown a Between pins 4 amp 5 Heating Element Under 4 Normal o Between pins 1 amp 2 Sensor Under 109 Normal 1 9 oj 3 A AL O wae Fi ic Between pins 3 amp Tip ee 14 1 Turn the nut anticlockwise and remove the tip enclosure and the tip Turn the nipple anticlockwise and remove it from the iron Pull Heating Element 0 out of Handle Toward the tip of the iron Do not use metal tools such as pliers to remove tip or Tip enclosure from the handle Measure when the heating element is at room temperature 1 Resistance value of heating element white under 4 Q Resistance value of sensor Red and Green under 10 Page 20 Feeder Tube Assembly 0 46m Short Tube Feeder Tube 0 46m Feeder Tube 0 8m Guide Tube Assembly Using for top Feeding Guide Tube Assembly Using for bottom Feeding Page 5 Parts name Main unit 4 Lead free soldering iron 6 Pressure adjutingscew 8 Solder Wine Axis Install Solder Wire 9 Solder Wire holder Install Solder Wire Axis 10 Meutpite 11 Cleaning sponge iS 12 Pedal Switch Optional Part Feeder Tube Asse
13. mbly 17 Feeder Tube Head Page 6 loosing it returning once and then stop working Feeding Length and Feeding Interval and Feeding Mode are all useless when the Feeding Mode is set as manual Auto Turn on Power Switch The unit will work according to setting parameters when stepping on pedal switch or pressing Touch Switch once All functions are useful SECTON 15 Tip care and use 1 Choose an appropriate temperature too high temperature can weaken soldering tip function and accelerate oxidation and shorten its service life Under the circumstance of able to work normally choose the temperature as low as possible Lower temperature can also solder adequately and protect sense elements Suggest to set temperature to 350 C 2 Make sure set the temperature of soldering iron to 220 C when use first time Make the soldering tip be tinned adequately Best of all dip it in tin for 5 minutes and then clean it with cleaning sponge set the temperature to 300 C again Repeat above steps Finally set the temperature to work temperature The purpose of this is to form a protecting film on tinned layer of soldering tip so it can prevent the oxidation at high temperature and failure of heat transport 3 Ifthe tinned part of soldering tip has black oxide it can be covered with new tin Clean it with humid sponge repeatedly until the oxide is completely removed and then covered with new tin Please do this cleaning regularly 4 Turn
14. ool to room temperature due to the burned danger e Don t touch the metallic parts near the Tip e Don t use the unit for applications other than soldering e Don t rap the soldering iron against the work bench to shake off residual solder or otherwise subject the iron to severe shocks e Don t wet the appliance and don t disconnect the appliance with wet hands and without to force the supply cord e The soldering process will produce smoke so make sure the area is well ventilated While using the unit don t do anything that may cause bodily harm or physical damage e The unit is equipped with a 3 wires grounding plug and must be plugged into a 3 terminal grounded socket Don t modify plug or use an ungrounded power socket Children don t realize the risks of electrical appliance Therefore use or keep the appliance only under supervision of adults and out of the reach from children Page 1 SECTION 1 Summary The unit is Automatic self feeder lead free soldering system Digital display adjusting with button furthermore design with automatic sleep and digital calibration function easy and prompt to use Adopt step motor feeding precise and the precision is controlled optionally Feeding speed and time returning are all adjustable and steady reach to perfect soldering effect and high efficiency One hand operation easy to solder With the optimized combination it works only with Soldering Iron without Sol
15. sing the A or Y button will change the displayed value as shown above for the 10 s place selection Press the button Here pressing the button a Enter the temperature setting into the internal memory b Display the temperature setting c Starts heater control Note If you turn off the power switch during the temperature setting setting value will not be stored in the memory If the temperature value outside of this range is selected the display will return to flashing the 100 s place If this happens reenter a correct temperature value Set temperature on line In the work if it is necessary to set temperature quickly and the heat elements can not be cut off the way may be selected Temperature rising Don t press knob and press A knob directly If so the setting temperature will raise 1 C and the display window will display the set temperature When loose the A knob the display window will delay the set temperature about 2 seconds If within 2 seconds of time press the A knob again the setting temperature will raise 1 C again If press the A knob and not loose at least 1 second the setting temperature will rise rapidly Till the needed temperature reaches then loose the A knob Temperature dropping Don t press knob and press Y knob directly If so the setting temperature will drop 1 C and the display window will display the se
16. ss the button the display shows 7 and the left most digit the 100 s digit in the display will flash This indicates the station is in password setting mode and the 100 s digit can be adjusted Using the A or Y button will change displayed value Set the password value in the same way described in set temperature normally After selecting the password of three digit press button The input password is error 5 Ifthe display window shows the present setting temperature two seconds later the station is in normal work state This indicates the password of input is error and the temperature setting can t be done The password of input is correct 6 If the display window shows DH this indicates the password of input is correct After displaying about 4 seconds the station comes into normal work state and the setting temperature will be admitted second and the returning length is 25mm The range is about 0 to 25mm 0 top 2Sa 14 6 Feeding Pressure setting The solder wire isn t sent out automatically because of inadequate feeding pressure you can adjust Pressure Adjusting Screw on top of unit to increase feeding pressure clockwise Solder wire is twisted because of too strong feeding pressure you can adjust it anticlockwise SECTION 9 Set Temperature Set Temperature Normally Caution Make sure the temperature of the station can be adjusted password is OK or the
17. t temperature When loose the Y knob the display window will relay the set temperature about 2 seconds If within 2 seconds press the Y knob again the setting temperature will drop 1 C again If press the W knob and not loose at least 1 second the setting temperature will drop rapidly Till the needed temperature reaches then loose the Y knob Page 13
18. the 191 192 thermometer for measuring the tip temperature If the unit is locked by password it will not be able to calibrate the nozzle temperature and you must input the right password SECTION 14 Operation Do corresponding operations in accordance with the chosen Feeding Mode Manual The Mode switch is set as 0 Turn on power switch and LED window display temperature the unit is in working state Step on Pedal Switch or press the red Touch Switch and the unit works After Page 18 SECTION 7 Installation Before installation please check the parts and make sure whether the power supply voltage accords with the nameplate 1 Install Handle Bracket assembly to the unit Screw off the Nut of the unit install bracket assembly on the screw and screw down the Nut 2 Install Feeder tube assembly There are two types of feeder tube assembly optional Length of 0 46m Short Tube and Length of 0 8m Long Tube Installation and operation have a little difference Installation of Short Tube Screw off the black nipple of handle assembly install the handle into the connector and screw on the black nipple again Unscrew the fixing screw of feeder tube head on the top cover of unit insert feeder tube head 7 and then tighten the screw Installation of Long Tube Screw off the black nipple of handle assembly install the handle into the connector and screw on the black nipple again Unscrew the fixing screw of feeder tube head on
19. the top cover of unit insert feeder tube head AD and then tighten the screw Finally insert plug 6 into socket behind the unit 3 Install pedal switch Put the plug of Pedal switch into pin 2 socket behind the unit 4 Install Solder wire a Pull the solder wire axis across the framework of solder wire and place it to the solder wire holder Q back of unit Make the notch on each side of solder wire axis lock into solder wire holder b Pull the solder wire head and insert it into wire guide tube behind the top push Handspike to widen the gap between two running gear wheels so it can cross the feeder tube easily Page 7 c Set the Mode Switch as 0 insert power plug and turn on Power Switch Make the feeder tube as straight as possibly step on Pedal Switch or press down the red Touch Switch until the solder wire is sent out Turn off power switch 5 Install Soldering Iron Screw off Nut on the bracket assembly and remove Handle clamping element Place soldering iron in the other Handle clamping element and install the previous one Make the Handle in the middle of them and then screw on Nut Connect plug of soldering iron handle to pin 6 receptacle in front of unit and tighten it 6 Adjust the position of Guide tube and Soldering tip Turn the Connector to change combination location of Guide tube and Soldering tip Unscrew Locking Screw of Guide tube and turn around Guide tube 43 can also change combinat
20. xample When the digit is set as 0 the speed is slowest with 2 7mm s When it is set as 1 the speed is 5 4mm s When it is set as 9 the speed is fastest with 27mm s Press the Speed Switch to set the suitable digit in accordance with working demand The range is about 2 7mm s to 27mm s 2 Feeding Length setting Feeding Length is designed with angle system namely with angle what the motor turned denotes Feeding Length Feeding Length is designed with three digit 001 to 999 denotes feeding length is 0 15mm to 150mm The resolution is 0 15mm namely each digit denotes 0 15mm 1 8 degree The setting method is the same as feeding speed Example When the digit is set as 001 the angle is 1 8 degree and the Speed Length is 0 15mm When the digit is set as 002 the angle is 3 6 degree and the Speed Length is 0 3mm When the digit is set as 999 the Speed Length is longest with 150mm and the angle is 1798 2 degree Press the Length Switch to set the suitable digit in accordance with working demand The range is about 0 15mm to 150mm Page 9 3 Feeding Interval Time setting Feeding Interval Time means the interval time between every feeding when the automatic feeding over two times Feeding Interval Time is designed with one digit 0 to 9 denotes the interval time is 0 second to 2 7seconds The resolution is 0 3 second namely each digit denotes 0 3 second The setting method is the same as Feeding Speed Example When the digit is
Download Pdf Manuals
Related Search