Asgård 1 / Asgård 2 / Asgård 2F
Contents
1. fuel but also as mentioned above increases the risk of producing soot smoke and other environmentally damaging by products Burning varnished wood impregnated wood chipboard paper and other waste is strictly forbidden Burning these materials will damage the environment the wood burning stove and your own health 3 3 How do light a fire in the wood burning stove The fire lighting method is very important for starting combustion quickly and efficiently 1 Open the primary air intake damper at the bottom of the door and open the secondary air intake at the top of the door The primary damper is used at the start to get the fire going while the secondary air intake keeps the fire burning evenly The secondary air intake is open when the damper is pushed all the way to the right and closed when the damper is pushed to the left 2 Place a log of wood crosswise in the combustion chamber and put 2 firelighters close to the log Light the firelighters and quickly put a new log close to the firelighters and several small logs at an angle above it Air must be able to reach the firelighters but the logs should be touching to warm each other 3 Keep the door approx 1 cm ajar until the glass is too hot to touch Then close the door When there are distinct visible flames and the fire has taken hold close the primary air intake damper Important The control handle will get warm when the wood burning stove is being used Please use the g2. Asgard 1 Asgard 2 Asgard 2F User Manual Ecolabel Sintef 110 0234 EN 13240 www aduro dk Asg rd Version 2 Good luck with your new wood burning stove In order to get the best possible pleasure and benefit from your new Asg rd wood burning stove it is important that you read this User Manual thoroughly before you install your wood burning stove and start to use it 1 0 General 1 1 Compliance Asg rd 1 2 2F complies with the EN 13240 European standards as well as the NS 3058 Norwegian standard and is thereby approved for installation and use in Europe The product documentation for Norway has Sintef number 110 0234 and can be downloaded from our website at www aduro no or from www nbl sintef no At the same time the manufacturing process is subject to external quality control Asgard 1 2 2F also carries the Nordic Swan Eco label which guarantees that the wood burning stove complies with the most stringent environmental requirements and has been manufactured in an environmentally correct manner 1 2 Technical data Nominal power 5 kW Chimney draught 12 Pa Maximum combustion amount per hour Wood approx 2 4 kg Heat rating in buildings with Optimum insulation 130 m Average insulation 90 m Inadequate insulation 50 m Flue outlet diameter 150 mm Weight Asg rd 1 75 kg Asg rd 2 58 kg og Asg rd 2F 158 kg 1 3 Transportation When taking your wood burning stove home please ensure that it tra
3. actor If the chimney draught is too strong a damper can be fitted to regulate the chimney draught Contact your local chimney sweep for more advice 4 1 Inadequate draught in the chimney If the chimney is too short leaks or is inadequately insulated there may be problems with the chimney draught let the chimney sweep assess this The draught should be approx 0 10 0 14 mbar in order to provide satisfactory combustion and prevent smoke leakage If the chimney sweep judges the draught to be satisfactory but you still have problems lighting a fire try extending the fire lighting phase using more thin pieces of kindling so that the chimney gets thoroughly warm The chimney will not draw at optimum effect until it is warm The fire lighting phase can be prolonged by using a lot of kindling and 1 2 firelighters When a layer of embers has been formed add 2 3 dry logs 5 0 Maintaining and cleaning your wood burning stove Gaskets With time the gaskets will wear and in order to avoid wild combustion they must be replaced as required Glass If the wood you burn is too moist you will get soot stains on the glass pane They can be easily removed using a damp cloth that you dip in cold ash and rub on the sooty glass Special cleaning agents are also available to remove soot from glass Combustion chamber The yellow tiles in the combustion chamber eventually wear out and they should be replaced when the cracks are more that 0 5 cm The du
4. affects combustion In normal circumstances you should not place more than two logs in the stove If you want an enhanced effect you can add more logs The nominal heat output is reached by burning approx 1 3 kg per hour 3 6 Secondary damper The secondary damper should always be open while the wood burning stove is in use This damper allows you to adjust the wood burning stove to the chimney draft and the heat output you require In normal circumstances the wood burning stove should be working with this damper open between 60 and 100 You should never close the air intake so far that the flames are extinguished There should always be visible flames in order to achieve clean and efficient combustion 3 7 Primary damper When you add a new log the primary air intake damper should be opened until the fire is burning properly In order to utilize the fuel to the fullest extent the embers should have burnt for so long that it is necessary to open the primary air intake for approx 2 minutes to get the new log to burn In order to reduce the risk of ash falling from the stove when the door is opened to add more fuel it is a good idea to open the primary air intake damper for approx 1 minute before the door is opened This increases the draught through the stove and reduces the risk that ash will drop on the floor Please note if you overload the wood burning stove and burn more than approx 2 5 kg wood hour there is a risk that the lacquere
5. and ajar for the first few minutes e In the event of a chimney fire Close all the dampers on the wood burning stove and call the fire fighting service 3 2 Recommended fuels We recommend the use of split hardwood that has been stored outdoors under cover for at least 1 year Wood that has been stored indoors has a tendency to become too dry and will burn too quickly The wood should preferably be felled in the winter when a lot of the moisture in the wood will have been drawn down into the roots In order to achieve optimum combustion the wood s moisture level should not exceed 18 which roughly corresponds to storing the wood under cover outdoors for one year The moisture level of the wood can be measured using a moisture meter or by applying washing up liquid to one end of the log and blowing air in the other end If the wood is dry enough soap bubbles will appear The wood should be chopped into logs with a diameter of approx 10 cm and a log length of max 33 cm Correct firing provides optimal heat output and maximum economy At the same time correct firing prevents environmental damage in the form of smoke and malodorous fumes and also reduces the risk of chimney fires Well seasoned wood fuel is essential for correct use Make sure your fuel is kept dry If the fuel is wet a large proportion of the heat will be used to vaporize the water and this energy will disappear up the chimney It is clearly not only uneconomical to fire with wet
6. d renewed using the original Senotherm paint in an aerosol can It is available in black or grey from your local dealer Please note All maintenance and cleaning of the wood burning stove should be carried out when it is cold Spare parts and unauthorized alterations You may only use original spare parts in the wood burning stove Consult your dealer for advice and when purchasing spare parts All forms of unauthorized alterations to the wood burning stove are strictly forbidden as the wood burning stove will no longer comply with the approved specifications 6 0 Accessories There is a wide product range of accessories for Asgard stoves Companion sets Firebaskets in felt and bonded leather Firewood buckets Briquette bucket and ashbucket Fireplace hearth fence Glass and steel floor plates Flue pipes 7 0 Product liability and warranty In accordance with the Danish Sale of Goods Act product liability will exist for two years from the date of purchase of the wood burning stove The dated receipt will be sufficient proof Product liability will not cover damage caused by incorrect installation and use of the wood burning stove Likewise product liability will not cover loose parts and wear parts fireproof tiles glass gaskets rails cast iron grate and control as they are worn by ordinary use These parts can be purchased as spare parts 8 0 FAQ If you need more information please go to www aduro dk Enjoy your stove
7. d surface of the stove will become discoloured and eventually fall off The stove can be resurfaced but this is not covered by the manufacturer s guarantee In the same way any other damage to the stove caused by overloading will not be covered by the guarantee 3 8 Ventilation fresh air supply In order for the wood burning stove to function at optimum efficiency air is needed for the combustion process There must be sufficient fresh air coming into the room containing the wood burning stove In very well insulated houses or houses with powerful cooker hoods and or air conditioning systems a vacuum can be created around the stove leading to smoke leakage and poor combustion In these circumstances it might be necessary to open a window to provide air for combustion and to equalize the vacuum Alternatively you could fit an air vent in the room containing the wood burning stove 4 0 The chimney Data for chimney calculation Wood Flue temperature at 20 C 367 Chimney draught at testing power mbar Pa Orlane Flue gas mass flow g s 4 0 The optimum combustion is achieved at a constant chimney draught of 0 10 to 0 14 mbar measured in the flue pipe above the stove There are many factors that affect the chimney draught including the outside temperature wind strength and surrounding buildings If it is impossible to establish a sufficiently natural chimney draught the chimney can be fitted with a smoke extr
8. love provided when you operate the wood burning stove 3 4 The first time a fire is lit The first few times the wood burning stove is used there may be some smoke and unpleasant odours from the wood burning stove which is fairly normal This is caused by the heat resistant paint hardening Make sure there is sufficient ventilation during this stage It is also important not to let the fire burn too fiercely the first 2 3 times so that the wood burning stove has time to expand slowly You should also be aware that the stove may make clicking sounds as it heats up and cools down rather like pouring boiling water into a sink These are caused by the great differences in temperature to which the materials are being exposed During the first firing which should be carried out using approximately 1 kg of wood the stoking door must be left slightly open and must not be closed until the stove is cold This is to prevent the sealing rope sticking to the stove 3 5 How should I use my wood burning stove The wood burning stove is intended for intermittent combustion This means that each stoking should burn down to embers before new logs are added In order to obtain the best possible combustion you should regulate the effect heat output with the fuel Burning small logs provides more powerful combustion than burning large logs as the surface area is greater and more gas is released The amount of wood in the combustion chamber is another factor that
9. materials The Asgard 1 2 2F should be installed at a distance of 20 cm from flammable materials at the rear and at a distance of 30 cm from the side All furniture must be kept at least 85 cm away from the front of the stove If the stove is installed with an insulated pipe then you may reduce the distance behind the stove to 10 cm See illustration below If the stove is positioned against a brick wall or other non flammable material there is no minimum distance requirement To facilitate cleaning and for the best use of the convection air we recommend that you leave a distance of approximately 5 10 cm to the wall The Asgard 1 2 2F is built as a convection stove This means that air from the room circulates between the inner stove and the outer covering As a result the heated air is distributed evenly throughout the room When using an insulated pipe Behind stove 20 10 t 30 s gt 30 lt gt 85 a Please note that the wood burning stove must be installed on a floor with the adequate load bearing capacity If the existing construction does not meet this requirement appropriate adaptation measures must be taken e g a load distributing plate If the wood burning stove is to be placed close to flammable material such as a wooden floor or carpet it must be placed on a non flammable base The floor plate should extend for at least 30 cm in front of the wood burning stove and 15 cm on each
10. rability of the tiles will depend on how often and how intensively the stove is used You can change the tiles yourself They are available as a ready to use set You can also buy one piece tiles that you can cut to the size of the worn plates yourself Please consult your dealer Ash Empty the ash drawer before it becomes completely full Always leave a layer of ash on the bottom of the stove as this insulates the combustion chamber and makes lighting a fire easier Cleaning the wood burning stove The stove s surface is treated with a heat resistant Senotherm paint which will stay at its best just by being vacuumed with a small soft mouthpiece or dusted with a soft dry cloth Do not use spirit or other solvents which will remove the paint The inside of the wood burning stove and the flue pipe can be cleaned via the door and the cleaning aperture in the flue pipe chimney The upper fireproof tile the exhaust deflector can be removed allowing access to the top of the wood burning stove Cleaning of the inside of the wood burning stove and the flue pipe should be undertaken at least once a year or more frequently if necessary depending on how often the wood burning stove is used This work can also be carried out by the chimney sweep Soapstone Asg rd 2F You can clean your soapstone by wiping it with a soft moist cloth Repairing the surface If the surface of your wood burning stove gets scratched or worn it can easily be reface
11. side 2 2 Connection to a brick chimney If the stove is being connected to a brick chimney a curved flue pipe should be used via the top outlet After measurement a hole is made in the chimney in which the pipe sleeve is placed and fireplace mortar is used to seal it in place The stove is placed in position and the flue pipe is put in place A thin gasket is placed between the flue pipe and the pipe sleeve to seal the joints The flue pipe should protrude 5 10 cm into the pipe sleeve but must not block the opening in the chimney see the illustration below The wood burning stove can be connected to a chimney to which other heat sources are connected 3 0 Lighting a fire in the wood burning stove 3 1 Important safety information e The wood burning stove will become warm during use and therefore it should be treated with all necessary caution e Never keep easily combustible fluids such as petrol in the vicinity of the wood burning stove and never use easily combustible fluids to light the fire in the wood burning stove e Never empty the ash drawer when the wood burning stove is warm Embers may still be found in the ash drawer for up to 24 hours after the fire has gone out Please wait to empty the ash drawer until you are sure that there are no embers in the ash e The door should be kept closed while the wood burning stove is in use While lighting the fire the door can st
12. vels in an upright position If you wish to lay it flat it is important that you remove loose parts from the combustion chamber cast iron grate and loose fireproof tiles and remove the ash drawer Alternatively you could also fill the combustion chamber with excess packaging so the parts are kept in place 1 4 Serial number The wood burning stove has a serial number on the rating plate on the back of the stove Please write this number in the space below For the purposes of the guarantee and for other enquiries it is important that you are able to quote this number Serial number 2 0 Installation of the wood burning stove You are welcome to install your wood burning stove yourself but we strongly recommend that you consult your chimney sweep before you begin the installation Your dealer can also provide you with installation advice It is important to ensure that all local rules and regulations including ones relating to national and European standards are complied with when installing this device Please note You may not begin to use the wood burning stove until it has been inspected and approved by your local chimney sweep 2 1 Position of the stove distance requirements The new wood burning stove must be installed in a suitable and physically possible position You need to be sure that the position complies with local regulations Distance requirements will only apply if the wood burning stove is to be placed close to flammable
Download Pdf Manuals
Related Search