DATA SHEET - Davis Controls Ltd.
Contents
1. rating of output module Risk of fire and erroneous operation Do not use the PLC in the environment of direct vibration Risk of electrical shock fire and erroneous operation Do not disassemble repair or modify the PLC Risk of electrical shock fire and erroneous operation When disposing of PLC and battery treat it as industrial waste Risk of poisonous pollution or explosion Precautions for use Do not Install other places except PLC controlled place Make sure that the FG terminal is grounded with class 3 grounding which is dedicated to the PLC Otherwise it can cause disorder or malfunction of PLC Connect expansion connector correctly when expansion module is needed Do not detach PCB from the case of the module and do not modify the module Turn off power when attaching or detaching module Cellular phone or walkie talkie should be farther than 30cm from the PLC Input signal and communication line should be farther than 10cm from a high tension and a power line in order not to be affected by noise and magnetic field 2 Parameter area of analog output module a XBF DV04A Specify channel to use Bit On 1 Channel used Bit Off 0 Channel unused Read Write available 0 Outputs the previous value 1 Outputs the min value of output range 2 Outputs the mid value of output range 6 Specify Ch3 output type 3 Outputs the max value of output range b XBF DCO4A Read available Address Descriptio2. DATA SHEET LS Programmable Logic Controller Analog Output Module XGB XBF DV04A XBF DCO04A XBF DC04B When using LSIS equipment thoroughly read this datasheet and associated manuals introduced in this datasheet Also pay careful attention to safety and handle the module properly Store this datasheet in a safe place so that you can take it out and read it whenever necessary Davis Controls ft Davis Controls Ltd ts the authorized distributor of LSIS equipment and control solutions throughtout Canada Founded in 1933 Davis Controls represents a strong and balanced portfolio of world class products From head office facilities located in Oakville Ontario Davis Controls connects customers seeking high quality automation solutions with global manufacturers of state of the art products You can contact us at Toll Free Canada 800 701 7480 Toll Free USA 300 386 4159 Email infoiidaviscontrols com Website waw daviscontrols com Thank you for your business and your interest in L515 solutions LS constantly endeavors to improve our products so that information in this datasheet is subject to change without notice The date of issue 2011 5 10310000685 Ver 3 0 1 Precautions for wiring a Don t let AC power line near to analog input module s external input sign line With an enough distance kept away between it will be free from surge or inductive noise b Cable shall be selected in due considerat
3. Error occurs Off DC 5V disconnected Module error Analog output Analog output voltage current terminal terminal whose respective channels can be connected voltage current with external devices External power input External power input terminal supplied DC terminal 24V for analog output voltage current Dimension of XBF DV04A XBF DC04A XBF DC04B is same RQ SAN RQ AN ROA RQ ANN RO Hg Rs EXPANSION CONNECTOR 1 Warranty period LSIS provides an 18 month warranty from the date of the production 2 Warranty conditions For troubles within the warranty period LSIS will replace the entire PLC or repair the troubled parts free of charge except the following cases a The troubles caused by improper condition environment or treatment except the instructions of LSIS b The troubles caused by external devices c The troubles caused by remodeling or repairing based on the user s own discretion d The troubles caused by improper usage of the product e The troubles caused by the reason which exceeded the expectation from science and technology level when LSIS manufactured the product f The troubles caused by natural disaster 3 This warranty is limited to the PLC itself only It is not valid for the whole system which the PLC is attached to 3 Parameter setting of XDL BSSA Dnet I F adapter Analog output range and digital input range can not chage That is Analog volatge output range Analog current outp
4. and User s Manual mean as follows IN This symbol means paying attention because of danger of injury fire or malfunction gt This symbol means paying attention because of danger of electric shock Store this datasheet in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Handling Precautions Don t drop or make impact Don t detach PCB from case It may cause problem When wiring let no foreign material go into the module If it goes into the module remove it Don t detach the module from slot while power is on Warning gt Do not contact the terminals while the power is applied Risk of electric shock and malfunction gt Protect the product from being gone into by foreign metallic matter Risk of fire electric shock and malfunction gt Risk of fire electric shock and malfunction Risk of injury and fire by explosion and ignition N Caution Be sure to check the rated voltage and terminal arrangement for the module before wiring work Risk of electric shock fire and malfunction Tighten the screw of terminal block with the specified torque range If the terminal screw is loose it can cause fire and electric shock Use the PLC in an environment that meets the general specifications contained in this datasheet Risk of electrical shock fire erroneous operation and deterioration of the PLC Be sure that external load does not exceed the
5. ion of ambient temperature and allowable current whose size is not less than the max cable standard of AWG22 0 3mm c Don t let the cable too close to hot device and material or in direct contact with oil for long which will cause damage or abnormal operation due to short circuit d Check the polarity when wiring the terminal e Wiring with high voltage line or power line may produce inductive hindrance causing abnormal operation or defect 2 Wiring example a Analog voltage output module Motor drive etc XBF DV04A Converter circuit Remarks 1 Use the cable of 2 core twisted shield b Analog current output module Motor drive etc XBF DC04A 5108 or less D A Converter circuit DC 24V DC 24V Safety Precautions gt Safety Precautions is for using the product safely and correctly in order to prevent the accidents and danger so please go by them The precautions explained here only apply to this module For safety precautions on the PLC system refer to User s manual gt The precautions are divided into 2 sections Warning and Caution Each of the meanings is represented as follows If you violate instructions it can cause death fatal injury or a considerable loss of property Warning A i If you violate instructions it can cause a slight injury or a slight Z Caution oss of products gt The symbols which are indicated in the PLC
6. n Details Remark Bit On 1 Channel used Bit Off 0 Channel unused EA Specify channel to use 1 Specify current output Bit 00 4 20mA range Bit 01 0 20mA Bit 00 0 4000 Bit 01 2000 2000 Bit 10 400 2000 0 20000 0 Outputs the previous value 1 Outputs the min value of output range 2 Outputs the mid value of output range 6 Specify Ch3 output type 3 Outputs the max value of output range Specify input type Read c XBF DC04B Bit On 1 Channel used Le Specify channel to use Bit Off 0 Channel unused Specify current output p he Bit 00 0 4000 Bit 01 2000 2000 Bit 10 0 1200 Bit 11 0 1000 0 Outputs the previous value 1 Outputs the min value of output range 2 Outputs the mid value of output range 6 Specify Ch3 output type 3 Outputs the max value of output range Specify input type Read Read Write available available Read Write available Related Manual Read this data sheet carefully prior to any operation mounting installation or start up of the product Pp otC _CNUONames CCSSNCNCNCNCNC L Ct N CCCde Cs XGB analog XGK XGB Instruction amp Programming XGI XGR XEC Instruction amp Programming XGB Hardware XGB Hardware IEC XG5000 Revision History 2006 11 2009 05 2011 05 Updated Information First Edition Error in performance specifications is fixed V3 0 KOREAN ENGLISH data sheet integ
7. rated CI Changed Applicable version For system configuration the following version is necessary o y oem Y O Applicable Version XG5000 V3 6 or above o Specification sid Operating ET temperature Qaant Storage on Operating 7 5 95 RH non condensing Storage humidit Standard 5 95 RH non condensing For discontinuous vibration 10sf lt 57Hz 0 075mm Vibration 57 sf lt 150 hz 9 8 0G 0tmesin resistance Mon tee 10sf257Hz __ 0 085mm xyz 57sfs150 Hz 4 9ms 0 5G _ e Max impact acceleration 147 mS 15G e Authorized time 11ms e Pulse wave Sign half wave pulse Each 3 times in X Y Z directions Square wave AC 1 500V impulse noise DC 900V Electrostatic discharge Voltage 4kV Contact discharge Radiated electromagnetic 80 1 000 MHz 10 V m field noise Digital analog Be input output iti auc communication ogu interface Pi IEC61131 2 Shocks resistance IEC61131 2 LSIS standard IEC61131 2 IEC61000 4 2 IEC61131 2 Noise IEC61000 4 3 resistance Segment IEC61131 2 IEC61000 4 4 Fast transient burst noise o Extendable Smart I O adapter can be installed up to 4 analog input modules 1 Parameter setting of XPL BSSA Pnet I F adapter a Parameters setting window Description All Parameter Data in hex description Cancel Parameter Data Common b Parame
8. ter setting description 1 XBF DV04A XBF DC04A 2 XBF DV04A Setting value Analog voltage output range Digital input range Value O 0 10V 0 4000 0 10V O 1000 3 XBF DC04A o f o h ooo Oeo Value Remarks If do not set parameter value operates on initial value 0 Setting value inputs in analog output respectively input range is 0 1 0 3 Parameter value is maintained in connecting communication At disconnecting communication parameter value is same as initial value when power is changed Off to On status XBF DV04A XBF DC04A XBF DC04B pe pco tov pe d 20m DCO 1 2m Load Load Load resistance resistance 2kQ or more Aaaa 5100 or less pe Signed 12 bit binary data Unsigned a value 0 4000 0 4000 0 4000 Singed R Valia 2000 2000 2000 2000 2000 2000 Precise 400 2000 Value 1000 0 2000 O 1200 0 1000 0 1000 0 1000 Percentile Value Max resolution 0 344 1 4000 Accurac Max conversion speed Oooo o 4Chanea ss Absolute max output Output channel Photo coupler insulation between output terminal and PLC power no insulation between channels 11 Point terminal Range Digital input Range Insulation method Terminal connected I O occupied points Fixed point assignment 64 Point Internal DC 5V Consumed External 70q SASSER BSSEE No PartName Description _ Displays the operation status On Operation normal BUN TED Blink
9. ut range is fixed 0 10V 4 20mA and digital input range is fixed 0 4000 available Ch2 setting error Ch3 setting error peov _ DC 0V Remarks 1 Use the cable of 2 core twisted shield 1 U area of analog output module d Bit Area Address F E D C B A 9 8 7 6 5 4 3 2 1 0 pe ele ee le ee a te ee a 2 1 0 pe ae es fs cH cH2 CHi CHo Le a ee ee ee cH CH2 CH1 CHO 3 Error code Offset gain adjustment mode 2Sec Xx stands for the channel with error found a XBF DV04A XBF DC04A Address Description Details Remark Module ready F Bit On 1 Module ready 0 3 Bit On 1 Channel Channel error status ater Bit On 1 Channel used UOx 01 Bit Off 0 Channel unused U0x 02 Output status setting Bit On 1 Output Allowed Bit Off 0 Output disabled U0x 00 Read available 1 Sec Read Write 12 Bit binary data aane b Bit area F Jef pjc B ajo 8a 7 6e 5 4 3 2 1 0 Uox 00 Modue CH3 CH2 CHi CHO Uox o1 dT CT CH3 CH2 CHI CHO Uox o2 fenster CHI CHO U0x 03 RI U0x 06 12 bit binary data
Download Pdf Manuals
Related Search