WT-9002N GSM Intercom, Access Control And Alarm System USER
Contents
1. WT 9002N GSM Intercom Access Control And Alarm System USER MANUAL WITURA TECHNOLOGY SDN BHD WT 9002N GSM Intercom User Manual V1 0 Eo INTRODUCTION The WT 9002N is a GSM Intercom that comes with its own stainless steel external call point and when visitor igs at the gate presses the call button the system will call the numbers programmed regardless of the location of the telephone being called The system can call up to 5 mobile phones or landline number in the order they were programmed Once the owner has responded by answering the call the visitor at the gate and the owner can have a normal two way conversation voice communication When the owner decide to allow the visitor to enter the premises all the owner has to do is to send the SMS text message to the unit and the gate or door will open The WT 9002N is also an access control system You can register up to 5 users into the system and if any of these users call the system it will reject the call and open the gate without any cost of call Absolutely Fee of Charges Of course if the incoming call is not the registered user the door will never open The WT 9002N also comes with 2 inputs which can connected to motion sensors or magnetic sensors and will send alarm messages to 5 mobile phone numbers when one of these input triggered The WT 9002N comes with its own stainless steel call point if you prefer other design you can choose to let the WT 9002N wo2. when the cards credit falls below a certain limit please contact your network provider or visit their website for more details Most but not a using post paid SIM cards will be de activated by the network if not used to make an outgoing voice call or send an SMS text message within a specific period To prevent this simply send the GSM Remote Control Switch a text command O PW3H then 2 it will reply by text message do this once a month to keep the SIM card active Troubleshooting Ensure that your DC power supply is connected Red power LED not alight correctly positive to terminal 220v and negative to terminal N Verify 12 volts is present using a volt meter Ensure your SIM card has been activated and that the Blue network LED flashing every one second PIN request has been disabled If the unit is in a low and not every 3 seconds signal strength area consider using an external GSM antenna or changing to another network provider Ensure your telephone number is in the Administrator am not receiving confirmation test messages list and that sending text messages to your number is when program the administrators number enabled Ensure the unit is connected to the GSM network by am not receiving any text messages when observing the blue network LED it should be flashing initially programming the unit once every 3 seconds see 2 above Ensure the SIM card has credit Most but not all PAY SIM car
3. Privacy and Mode switch lt OFF gt Security before you decide to use the Open Mode 2013 10 10 17 13 Thu Factory Default is N 1 for Security Mode WITURA TECHNOLOGY SDN BHD WT 9002N GSM Intercom User Manual V1 0 e SMS Text Message to Switch On Off When Setting as N 1 means switch on the relay Relay 24 1 by SMS Message Master relay lt ON gt N 0 means switch off the relay by SMS Message 2013 10 10 17 13 Thu When Setting as 24 O Master relay lt OFF gt 2013 10 10 17 13 Thu Step 3 Installation Connector to Connect With Speaker Left to Yellow Wire Right to Reset Button White Wire Connector to Connect i with MIC Left to Shield Ground Wire Right to White positive Shielded Wire 26 G5M Module SIM Card Holder Antenna Connector to connect the wire from the press 12W 4 12V N L button GND to Blak Connect with the AC220VAdapter Wire Another to RED Power of the external Wire control devices ie Maenetc Door Sensor CLW The ma powers that can control are ACZ40V 204 Insert the SIM card to access the SIM card carrier gently push the button adjacent to it insert the SIM card and carefully close the carrier Connect the cable to terminals 220V amp N ensuring positive is connected to terminal 200V switch on the power supply the red power LED will light indicating power is present the blue network LED indicator will initially flash quickly once logged onto the network
4. ds will be de activated by the network if not used to make an outgoing voice call The unit has been working for several months or send an SMS text message within a specific period and has now stopped responding to calls and To prevent this simply send a txt command 0 PW text commands then 2 it will reply by text message do this once a month to keep the SIM card active WITURA TECHNOLOGY SDN BHD WT 9002N GSM Intercom User Manual V1 0 ae Warranty Witura Technology Sdn Bhd warrantees the WT 9002N GSM Intercom against defective parts and workmanship Witura Technology Sdn Bhd shall at its option repair or replace the defective equipment upon the return of such equipment to any Witura branch This warranty applies ONLY to defects in components and workman ship and NOT to damage due to causes beyond the control of Witura such as incorrect voltage lightning damage mechanical shock water damage fire damage or damage arising out of abuse and improper application of the equipment Note Wherever possible return only the PCB to Witura Service Centres DO NOT return the enclosure The WT 9002N is a product of Witura Technology Sdn Bhd And is manufactured by Shenzhen Witura Telecommunications Co Ltd WARNING For safety reasons only connect equipment with a telecommunications compliance label This includes customer equipment previously labelled permitted or certified WITURA TECHNOLOGY SDN BHD WT 9002N GSM I
5. et Admin number 18617185300 into admin 2 1 2 18617185300 You get administrator privileges 2013 10 09 00 33 Wed New password lt 1212 gt 2013 10 10 16 07 Thu Administrator 1 15989427391 2 18617185300 2013 10 10 16 08 Thu Administrator 1 15989427391 2 18617185300 2013019019 16 09 Thu When you enter 0 1234 you enter into the programming mode You must perform the next command in 10 minutes If you did not do anything the exit from system will programming mode Maximum 4 digits of passwords If you decide to protect your privacy you can change the factory password to your new password Enter the factory password follow by your new password Set Admin Numbers number number number number number set 1st admin set 2nd admin set 3rd admin set 4th admin set 5th admin Only the number in the list can receive alarm texts message and active the relay output You can add up to 5 telephone number into the admin list WT 9002N GSM Intercom User Manual V1 0 Delete the admin number in the list 3 N Administrator Delete Admin Number 1 15989427391 Delete 1st admin 3 1 N Admin number 1 5 2 Delete 2nd admin 3 2 For example if you want to i Delete 3rd admin 3 3 delete admin no 2 Delete 4th admin 3 4 just enter 3 2 Delete 5th admin 3 5 2013019019 17 16 Thu Check the relay status in ON or OFF Master relay lt ON gt The unit will retu
6. he network flash inconsistently until it locates the network A Phone Call to the SIM Card Number will now Latch the Relay and open the gate permanently ON and Switch the gate or door being Controlled On The Status of the Relay will remain as on until the unit receives a second Call to the Unit of which will now Latch the Relay Permanently off Both Calls used to Latch the Relay either on or off are automatically disconnected once the relays are activated and never incur any Network Call Costs Beside calls to switch off or on the unit also can be permanently switch off and on by sending the unit a text message command WITURA TECHNOLOGY SDN BHD WT 9002N GSM Intercom User Manual V1 0 a Step 1 The simplest set up methods to set up Administrator number Applied the KISS Principle keep it simple stupid The GSM Remote Control Switch is easy to setup and use Insert the SIM card simply use your mobile phone call to the unit your mobile phone number will automatically register as the 1st Administrators You will receive the following SMS message from the unit Administrator 1 18617185300 your phone number Zz 3 4 5 Call to the SIM Card No of WT 9002 a 4 a eoo DIG lt 2 31 pm 100 Messages WT 9002 Contact Administrator i if 2 ot qe 5 O Send You already finish the set up Now you can press the call button the unit will call to your mobile phone and you also can use
7. it will flash more slowly approximately one every 3 4 seconds WITURA TECHNOLOGY SDN BHD WT 9002N GSM Intercom User Manual V1 0 is It is recommended that the GSM Intercom Switch be programmed to operate as required before final installation Connection Details If you are unsure how to connect the device you wish to control refer to a qualified person Blue Connector at Power Supply Press Press Details Button Button Wire 1 Wire 2 WITURA TECHNOLOGY SDN BHD WT 9002N GSM Intercom User Manual V1 0 Production Specifications Operation Voltage 12 volts DC Operating Current Maximum 500mA typically 55mA Relay Contacts 1 x Normally Open and Normally Closed Contacts maximum switching capacity 20 amps 230v ac per relay GSM Frequency MHz GSM 850 GSM 900 GSM 1800 GSM 1900 Physical Size 130 x 100 x 50mm CE FCG ETS Preparing the SIM card All new SIM cards have to be registered with the network provider before they can be used usually by calling the network provider or registering on their website please refer to the instructions supplied with your SIM card During the registration procedure a confirmation code or text message is usually sent to the SIM cards telephone number to be able to read and react to the message you will need to insert the SIM card into an unlocked mobile phone After successfully registering the SIM card ensure there is sufficient credit on the card for programming confir
8. mation texts to be sent from the GSM Remote Control Switch You MUST ensure that the PIN request is disabled from the SIM card before inserting it into the GSM Remote Control Switch If you do not disable the PIN request the GSM Remote Control Switch will not work If the PIN request is not disabled and the unit is switched on more than 3 times you will have to reset the PIN using the PUK code which will have to be obtained from the service provider To check the PIN request status of your SIM card place the card in an unlocked mobile phone switch the phone on If you are able to make calls without entering a PIN number the PIN request is disabled If a PIN number is requested refer to the instructions supplied with the SIM card and then look through the phones options for the disable PIN request and disable it You MUST disable any voicemail that is set up on the SIM card the codes shown below are for UK networks only please refer to your network operator if outside the UK Vodafone 1210 gt Send you will hear order is accepted and confirmed O2 Call 1760 gt Send you will hear order is accepted and confirmed T Mobile Call 222 and follow instructions WITURA TECHNOLOGY SDN BHD WT 9002N GSM Intercom User Manual V1 0 aa Orange Call 450 and follow instructions The SIM card is now ready to use We recommend that if you are using a pay as you go PAYG SIM card that you choose to automatically Top Up
9. ntercom User Manual V1 0 ca
10. on of the control equipment inside The call point is a two piece fixing with the shield located and fixed and the main intercom fascia locked into place and secured via the security fixing on the under frame of casing and again providing a very secure vandal resistant and waterproof housing It is advised the distance from the interface to the call point does not exceed 3 meters and it is also advice to install at least an 8 core in the event you may want to use a backlight version of the call point or change at the later stage to a keypad or camera version available later this year The user also can download the FREE apps from Android and IOS stores as their easy monitoring and control tools Just one touch on the apps user smart phone will sent the SMS text commands to the unit The users don t need to remember the commands code SETTING UP AND PROGRAMMING Once you have located and installed both the interface and the call point you have the 8 cores coming from the call point and will require a power source to the unit and the connecting cables from the interface to the gate control board to connect into the gate input pulse connection to activate the gates via the Intercom Interface When first booting up the system you will see Green LED Lights on the side of the Enclosure and it should light up when the Network is applied to the unit The Green LED is the network Indicator and this will light up when attempting to log on to t
11. rk with any other call point by simply connect the 4 wires from the WT 9002N to other manufacturer call point system it will work well The WT 9002N supports timer function the user can set schedule to open and close the gate For example put your gate or door on a schedule Turn off in 5 minutes turn on at 17 00 turn on 1 year later This function is important to use in the parking management school and door have to schedule to open in certain hours every day Another important feature for timer is to remind the owner to monitor the SIM Card expiry date User can instruct the unit to send the SMS to the user to keep the SIM card active before expiry dates The system using CE and FCC approved industry internal power supply connected on board A backup lithium battery can power up at least 8 hours and will sent a power down or power restored alerts in the event of any circuits power failure It is also possible to change or override the parameters of the output relays remotely via SMS and receive confirmations of these commands and add and remote authorized users without having to be present on site WITURA TECHNOLOGY SDN BHD WT 9002N GSM Intercom User Manual V1 0 2 The interface is housed in a back flanged IP 65 rated enclosure and can be located and fixed without having to open the cover or requiring any internal fixings within the enclosure making a secure and waterproof installation giving maximum protecti
12. rn Master Mode relay lt ON gt if the relay is on 2013 10 10 16 10 Thu The unit will return Master relay lt OFF gt if the relay is off 7 Check Signal Strength CSQ lt 28 gt You must confirm the signal strength at site before you 2013 10 10 16 11 Thu install the unit If the signal too weak the unit will not function properly CSQ 5 12 Signal too weak system not function CSQ 13 24 Signal Good System function well CSQ 25 32 Signal Excellent System working well Setting the year month day hours 12 YYYYMMDDHHMMX Time change OK YYYY 4 digit for Year minutes week MM 2 digit for Month 2013 10 10 16 05 Thu DD 2 digit for Date HH 2 digit for Hour 2 digit for Minutes 1 7 Day of the Week Example set as 12 2013101016054 which means 2013 10 10 16 05 Thu If reprogram the date it will take the last as the accurate date The date have to be correct if setting 2014 2 29 or 2013 11 31 this is the incorrect date which is not occur the system will verify the date time day if correct the date have to be after year 2013 WITURA TECHNOLOGY SDN BHD WT 9002N GSM Intercom User Manual V1 0 zp SMS Reply Message when the 21 N Message switch lt ON gt N 0 means SMS Reply system ON OFF Message when the system OFF 2013 10 10 17 06 Thu N 1 means SMS Reply Message when the system ON Factory Default as SMS Reply Message when the system ON If setting to not receive SMS Reply Message when
13. the system OFF the unit will return a message indicate successful setting for the command and it will no longer sending SMS reply until the setting of SMS Reply Message when the system ON is done When the system having the temperature alert wireless alarm alert it will automatically sending the alert message to the Admin 10 To receive SMS Reply Message or 22 N After sending N 1 means after make the not to receive SMS Replay Message command 22 0 phone call to the system it will when the system trigger by phone Status switch lt OFF gt return the SMS for the status to the caller call N 0 means after make the 2013 10 19 17 10 phone call to the system it will Thu not return the SMS for the Status to the caller After sending Factory Default as return SMS command 22 1 for the status after make the Master relay lt OFF gt ene call If you decide not to allow the system to 2013 10 10 17 08 oe vai for ariy Thu acknowledgement after you call to the unit You can switch OFF the text message Some Customer request this function because texts reply involved call cost 11 Security mode Open Mode 23 N When Setting as N 1 means in security mode Security Mode 23 1 Only allow the number in the Mode switch lt ON gt list can text to the unit to control the system 2013 10 10 17 13 Thu N 0 means in open mode Anybody can call to the unit to When Setting as Open control the system Please take Mode 23 0 note that the
14. your mobile phone call to the SIM Card number switch the device on permanently Another call to the SIM Card will switch the device off permanently If you do not required to go through details setting please process to STEP3 Final Installation and Wiring WITURA TECHNOLOGY SDN BHD WT 9002N GSM Intercom User Manual V1 0 a Factory Reset If you required to change the administrator number in the future simply press the button FACTORY at the mother board until you hear the du This means the unit back to the factory default Press until you hear the du sound This means you already reset the unit to factory default Now you can start to call again to set the administrator This method of setting is only allowed to set 1 administrator number If you wish to set more administrators please go to Step 3 Installation and set up WITURA TECHNOLOGY SDN BHD WT 9002N GSM Intercom User Manual V1 0 Is Step 2 Advance Set Up WITURA TECHNOLOGY SDN BHD First Step of programming you must enter the factory passwords of 1234 and go the programming mode inside You only can perform the next commands after enter into programming mode Change Password Add telephone number into the admin list Check phone number you program in the list emi 0 1234 0 1234 new password For example if you need to change to the new PW of 1212 0 1234 1212 1 1 telephone number For example s
Download Pdf Manuals
Related Search