operation manual
Contents
1. 0 BTX BEAM 5R ENGLISH OPERATION MANUAL MAINTENANCE e Make sure the area below the installation place is free from unwanted persons during servicing e Switch off the unit unplug the mains cable and wait until the unit has been cooled down During inspection the following points should be checked e All screws used for installing the device and any of its parts should be tightly fastened and may not be corroded Housings fixations and installations spots ceiling truss Suspensions should be totally free from any deformation e When an optical lens is visibly damaged due to cracks or deep scratches it must be replaced The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected In order to protect the device from overheat the cooling fans if any and ventilation openings should be cleaned monthly e The interior of the device should be cleaned annually using a vacuum cleaner or air jet The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics e Clean with a soft cloth using normal glass cleaning products e Always dry the parts carefully e Clean the external optics at least once every 30 days e Clean2. BRITEQS 13 18 BTX BEAM 5R ENGLISH OPERATION MANUAL 19 CHANNEL MODE BTX BEAMBR currently has 1 DMX mode 19CH mode Other additional DMX modes can be uploaded if needed ET ET ET RW Function P T Macro P T Macro speed 248 255 Macro31 240 247 Macro30 232 239 Macro29 0240 255 No Function 230 239 Lamp Off 220 229 Disable blackout while pan tilt 594 931 Macro 26 0 0 216 223 Macro27 210 219 Enable blackout while pan tilt gobo color change 208 215 Macro26 200 209 Reset all 200 207 Macro25 190 199 Frost Focus zoom reset 192 199 Macro24 180 189 No function 184 191 Macro 23 170 179 Shutter prism R Prism rest 176 183 Macro22 160 169 Gobo reset 168 175 Macro21 150 159 Color reset 160 167 Macro20 140 149 Pan tilt reset 152 159 Macro19 130 139 Lamp on 144 151 Macro 18 120 129 Disable blackout while gobo change 136 143 Macro17 110 119 Enable blackout while gogo change 128 135 Macro16 100 109 Disable blackout while color change 120 127 Macro15 90 99 Enable blackout while color change 112 119 Macro14 80 89 Disable blackout while pan tilt move 104 111 Macro 13 70 79 Enable blackout while pan tilt move 096 103 Macro12 60 69 Pan tilt normal mode 088 095 Macro11 50 59 Pan tilt fast mode 080 087 Macro10 40 49 Dimmer linear mode 072 079 Macro9 30 39 Dimmer conventional mode 064 071 Macro 8 0 29 No Function 056 063 Macro7 048 055 Macro6 040 047 Macro5 032 039 Macro4 024 031 Macro 3 016 023 Macro2 008 015 Macro1 000 007 Off
3. ENGLISH Operation Manual Other languages can be downloaded from WWW BRITEQ LIGHTING COM Ce K re D EAR CH LIGHT RES Version 1 0 RECYCLE EN DISPOSAL OF THE DEVICE Dispose of the unit and used batteries in an environment friendly manner according to your country regulations FR DECLASSER L APPAREIL D barrassez vous de l appareil et des piles usag es de mani re cologique Conformement aux dispositions legales de votre pays NL VERWIJDEREN VAN HET APPARAAT Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke manier conform de in uw land geldende voorschriften DU ENTSORGUNG DES GERATS Entsorgen Sie das Gerat und die Batterien auf umweltfreundliche Art und Weise gem den Vorschriften Ihres Landes ES DESHACERSE DEL APARATO Reciclar el aparato y pilas usadas de forma ecologica conforme a las disposiciones legales de su pais PT COMO DESFAZER SE DA UNIDADE fente reciclar a unidade e as pilhas usadas respeitando o ambiente e em conformidade com as normas vigentes no seu pais ENGLISH OPERATION MANUAL OPERATION MANUAL Thank you for buying this Briteq product To take full advantage of all possibilities and for your own safety please read these operating instructions very carefully before you start using this unit FEATURES This unit is radio interference suppressed This product meets the requirements of the current European and national guidelines Con
4. 13 15 Gobo4 10 12 Gobo3 7 9 Gobo2 4 6 Gobo1 0 3 White 251 255 Prism rotation effects 28 247 250 Prism rotation effects 27 242 246 Prism rotation effects 26 237 241 Prism rotation effects 25 233 236 Prism rotation effects 24 228 232 Prism rotation effects 23 224 227 Prism rotation effects 22 219 223 Prism rotation effects 21 215 218 Prism rotation effects 20 210 214 Prism rotation effects 19 206 209 Prism rotation effects 18 201 205 Prism rotation effects 17 197 200 Prism rotation effects 16 192 196 Prism rotation effects 15 188 191 Prism rotation effects 14 183 187 Prism rotation effects 13 178 182 Prism rotation effects 12 174 177 Prism rotation effects 11 169 173 Prism rotation effects 10 165 168 Prism rotation effects 9 160 164 Prism rotation effects 8 156 159 Prism rotation effects 7 151 155 Prism rotation effects 6 147 150 Prism rotation effects 5 142 146 Prism rotation effects 4 138 141 Prism rotation effects 3 133 137Prism rotation effects 2 128 132 Prism rotation effects 1 8 127 Prism Effect 0 7 No function 255 Fast Rotation P 194 Slow Rotation 190 193 Stop 189Slow Rotation 128 Fast Rotation 0 127 Index Rotation BRITEQ 255 100 248 255 Open 240 247 Strobe Random 204 239 Slow Open Slow Close 168 203 Fast Open Slow Close 132 167 Fast Close Slow Open 131 Fast Shutter 335 FF E 16 Slow Shutter 8 15 Open 0 7 Off 15 18 255 Dimmer Fine 100 255 100
5. BRITEQS 14 18 BTX BEAM 5R ENGLISH 255 Rotation Fast gt 194 Rotation Slow 190 193 Stop 189 Rotation Slow Q 128 Rotation Fast 064 127 Index 061 063 Color14 White 059 060 Color14 057 058 Color13 Color14 055 056 Color13 053 054 Color12 Color13 051 052 Color12 049 050 Color11 Color12 047 048 Color11 045 046 Color10 Color11 043 044 Color10 040 042 Color9 Color10 038 039 Color9 036 037 Color8 Color9 034 035 Color8 032 033 Color7 Color8 030 031 Color7 028 029 Color6 Color7 026 027 Color6 024 025 Color5 Color6 022 023 Color5 019 021 Color4 Color5 017 018 Color4 015 016 Color3 Color4 013 014 Color3 011 012 Color2 Color3 009 010 Color2 007 008 Color1 Color2 005 006 Color1 003 004 White Color1 000 002 White OPERATION MANUAL Ch10 Ch11 Ch12 255 Fast Rotation 194 Slow Rotation 190 193 Stop 189 Slow Rotation P 128 Fast Rotation 124 127 Gobo17 Shaking 120 123 Gobo16 Shaking 116 119 Gobo15 Shaking 112 115 Gobo14 Shaking 108 111 Gobo13 Shaking 104 107 Gobo12 Shaking 100 103 Gobo11Shaking 96 99 Gobo10 Shaking 92 95 Gobo9 Shaking 88 91 Gobo8 Shaking 84 87 Gobo7 Shaking 80 83 Gobo6 Shaking 76 79 Gobo5 Shaking 72 75 Gobo4 Shaking 68 71 Gobo3 Shaking 64 67 Gobo2 Shaking 60 63 Gobo1 Shaking 56 59 White Shaking 52 55 Gobo17 49 51Gobo16 46 48 Gobo15 43 45 Gobo14 40 42 Gobo13 37 39 Gobo12 34 36 Gobo11 31 33 Gobo10 28 30 Gobo9 25 27 Gobo8 22 24 Gobo 7 19 21 Gobo6 16 18 Gobo5
6. Prevent use in dusty environments and clean the unit regularly Keep the unit away from children Inexperienced persons should not operate this device Maximum save ambient temperature is 40 C Don t use this unit at higher ambient temperatures The units surface temperature may reach up to 85 C Don t touch the housing with bare hands during its operation Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing e Allow the device about 10 minutes to cool down before replacing the bulb or start servicing e Always unplug the unit when it is not used for a longer time or before replacing the bulb or start servicing e The electrical installation should be carried out by qualified personal only according to the regulations for electrical and mechanical safety in your country e Check that the available voltage is not higher than the one stated on the rear panel of the unit e The power cord should always be in perfect condition Switch the unit immediately off when the power cord is squashed or damaged It must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard e Never let the power cord come into contact with other cables e This fixture must be earthed in order to comply with safety regulations e Don t connect the unit to any dimmer pack e Always use an appropriate and certified safety cable when installing t
7. Pin3 Positive signal Pins4 5 not used e To prevent strange behavior on the dmx units due to interferences you must use a 900 to 1200 terminator at the end of the chain Never use Y splitter cables this simply won t work amp e Make sure that all units are connected to the mains e e ohm e Each unit in the chain needs to have its proper starting address so it knows which resistor BRITEQS 5 18 BTX BEAM 5R ENGLISH OPERATION MANUAL commands from the controller it has to decode In the next section you will learn how to set the DMX addresses OPERATING INSTRUCTIONS e Do not switch the unit on and off in short time intervals as this reduces the lamp life e Always unplug the unit when it is not used for a longer time or before replacing the bulb and or making the Service e Inthe event of serious operating problems stop using the fixture and contact your dealer immediately e Important Never look directly into the light source Don t use the effect in the presence of persons suffering from epilepsy Every time you turn on the unit it will run built in program to reset all motors to their home position the display will show the Briteq logo during the startup you may hear some noises for about 20 seconds It will show warning sign if one of the checks fails during the reset and you can press the MENU button to view the error information After that the unit will
8. be ready to receive DMX signal and the standard display will show as below on the right DMX Address Base 30 C Brea oo LIGHT RESEARCH BT X BEAM 5R Md 1 19Ch Standard display explained Shows the temperature of the CPU in the base Shows the DMX start address of the unit Shows the currently selected channel mode 19ch mode on the display SETUP MENU Main functions Turn on the unit press MENU button to enter into menu mode press UP and DOWN buttons until the required function is shown on the display Select the function by pressing the ENTER button Use UP and DOWN buttons to choose the submenu press the ENTER button to store confirm and automatically return to the last menu Press MENU button or leave the unit unused for one minute to exit menu mode BATTERY BACKUP FUNCTION While the unit is disconnected from mains power press UP button for one minute to enter into menu mode Press MENU button or let the unit unused during one minute to exit BRITEQS 6 18 BTX BEAM 5R ENGLISH OPERATION MANUAL The main functions are shown in the menu structure below the grayed boxes are the default settings 001 DMX Address u DMX Functions DMX Channel Mode View DMX Value y es Tilt Inverse No Fixture Setting P T Feedback Yes No Bl o P T Moving gt es Bl o Color Change No Bl o Gobo Change INCA On Off cane MENU OFF State Power On Off Via DMX No On if DMX On
9. gt es Lamp Setting O Off if DMX Off OS Ignition Delay OS Low Power Delay Display Inverse S es No Backlight Auto Off es Display Setting Backlight Intensity e Temperature Unit N Display Warning Yes BRITEQS 7 18 BTX BEAM 5R ENGLISH OPERATION MANUAL Auto Test Fixture Test Manual Test Lamp On time Fireware Version Exit Reset Time Fixture Information No Pan Tilt Yes No Shutter Prism Yes MENU No Color Yes Reset Functions No Yes No Yes Zoom Frost Focus No Yes Interval Fixture Maintenance Remain Time Special Functions y O Factory Setting Yes DMX Functions Enter menu mode select DMX Functions press ENTER button to confirm use UP and DOWN buttons to select DMX Address DMX Channel Mode or View DMX Value DMX Address DMX512 address setting Select DMX Address press ENTER button to confirm the current address will blink on the display use UP and DOWN button to adjust the address from 1 to 512 press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode Example Unit 1 Unit 2 Unit 3 Unit 4 19channels DMX Channel Mode To select DMX Channel Mode press ENTER button to confirm the current channel mode will blink on the display use UP and DOWN button to select Mode1 19 channels mode Press ENTER button to
10. the mains power Loosen the screws A open the cover B Loosen the screws C Unplug all the connect wires over the belt Change a new belt D put the belt around the axis gear and motor gear Ouhwond A BRITEQS 16 18 BTX BEAM 5R ENGLISH OPERATION MANUAL Plug all the connect wires back upon the belt Tighten all the screws 00 N If The tilt belt is broken Turn off the mains power Loosen all the screws A and open the right arm cover B Loosen the screws C that fix the bridge Change a new belt E Please adjust the tension of the belt properly Note do not fix the belt too tight as it is can easily break 5 Reverse the procedures from step 3 to 2 A GA Naj ERROR LIST Lamp Startup Fail It appears when there is no lamp or some wires are damaged Temperature Sense Error The temperature sensor is defect Lamp Too Hot Power Off The lamp temperature is higher than 110 c Check if the unit is properly ventilated fans or temperature sensor may be damaged Lamp Too Hot Low Power The temperature is higher than 105 c the unit will run on a low power level Maintenance Fixture The maintenance remaining time has passed please carry out maintenance and reset the timer in the menu Lamp On Over 700 Hour The lamp life is over 700 hours please replace the lamp Memory Initial Fail The memory IC is defect CPU B Error CPU C Error CPU D Error One of the CPU boards or so
11. V t Hofveld 2C B1702 Groot Bijgaarden Belgium Reproduction or publication of the content in any manner without express permission of the publisher is prohibited
12. ccompanying this appliance This symbol means indoor use only This symbol means Read instructions This symbol means Safety Class appliance OED E gt This symbol determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 12 meters The device is not suitable for direct mounting on normally flammable surfaces suitable only for mounting on non combustible surfaces e To protect the environment please try to recycle the packing material as much as possible e A new light effect sometimes causes some unwanted smoke and or smell This is normal and disappears after some minutes e To prevent fire or shock hazard do not expose this appliance to rain or moisture e To avoid condensation to be formed inside allow the unit to adapt to the surrounding temperatures when bringing it into a warm room after transport Condense sometimes prevents the unit from working at full performance or may even cause damages This unit is for indoor use only e Don t place metal objects or spill liquid inside the unit Electric shock or malfunction may result If a foreign object enters the unit immediately disconnect the mains power Locate the fixture in a well ventilated spot away from any flammable materials and or liquids The fixture must be fixed at least 50cm from surrounding walls Don t cover any ventilation openings as this may result in overheating
13. ck to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode Firmware Version Select Firmware Version press ENTER button to confirm firmware version will show on the display press MENU button back to exit Reset Functions Enter menu mode select Reset Function press ENTER button to confirm use UP and DOWN buttons to select Pan Tilt Shutter Prism Color Gobo Zoom Focus Frost or All Pan Tilt Reset Pan Tilt Select Pan Tilt press ENTER button to confirm use UP and DOWN buttons to select Yes the unit will run built in program to reset pan and tilt to their home positions or No press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode Shutter Prism Reset Shutter Prism Select Shutter Prism press ENTER button to confirm use UP and DOWN buttons to select Yes the unit will run built in program to reset shutter and Prism to their home positions or No press ENTER button to store Press MENU button to exit Color Reset Color Select Color press ENTER button to confirm use UP and DOWN buttons to select Yes the unit will run built in program to reset color to their home positions or No press ENTER button to store Press MENU button to exit BRITEQS 11 18 BTX BEAM 5R ENGLISH OPERATION MANUAL Gobo Reset GOBO Select Gobo press ENTER button to confirm use UP an
14. confirm Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode View DMX Value Select View DMX Value press ENTER button to confirm Channel function and its value will show on the display use UP and DOWN button to view other DMX values Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode BRITEQS 8 18 BTX BEAM 5R ENGLISH OPERATION MANUAL 0 Enter menu mode select Fixture Setting press ENTER button to confirm use UP and DOWN buttons to select Pan Inverse Tile Inverse BL O P T Moving BL O Color Change or BL O Gobo Change Pan Inverse Select Pan Inverse press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select No normal or Yes pan inverse press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode Tilt Inverse Select Tilt Inverse press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select No normal or Yes tilt inverse press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode P T Feedback pan tilt Feedback Select P T Feedback press ENTER button to con
15. d DOWN buttons to select Yes the unit will run built in program to reset GOBO wheel to their home positions or No press ENTER button to store Press MENU button to exit Zoom Frost Focus Reset Zoom Frost Focus Select Zoom Frost Focus press ENTER button to confirm use UP and DOWN buttons to select Yes the unit will run built in program to reset zoom frost and frost to their home positions or No and press ENTER button to store Press MENU button to exit All Reset All Select All press ENTER button to confirm use UP and DOWN buttons to select Yes the unit will run built in program to reset all motors to their home positions or No press ENTER button to store Press MENU button to exit Special Functions Enter menu mode select Special Functions press ENTER button to confirm use UP and DOWN buttons to select Fixture Maintenance or Factory Setting Fixture Maintenance Select Fixture Maintenance press ENTER button to confirm use UP and DOWN buttons to select Interval or Remain Time Interval select Interval press ENTER button to confirm the interval time will show on the display Press MENU button to exit Remain Time Select Remain Time press ENTER button to confirm the remaining time will show on the display press ENTER button to confirm use UP and DOWN buttons to select Exit or Reset time press MENU button to exit Factory Setting Select Factory Setting press ENTER button to confirm the fixture will r
16. e of spare parts bulbs fuses etc When replacing L parts please only genuine spare parts e Switch off the unit and unplug the mains cable e Wait for about 10 minutes until the unit has been cooled down Use a screwdriver to unscrew the screws to open the cover of the fixture Fig 1 Remove the fan Fig 2 Inside you will see the lamp socket Remove the lamp socket gently out of the lamp compartment Pull out the cable Fig 3 Replace the cable to the new lamp insert the lamp gently Fig 4 Adjust the hotspot using a screw Fig 4 Attention Check the label on the backside of the device or see the technical specifications in this manual to know which lamp should be used Never install lamps with a higher wattage Lamps with higher wattage generate temperatures the device was not designed for If the device uses a lamp transformer it will burn due to current overload Don t touch the bulb with bare hands This drastically shortens the lifespan of the lamp If you touched the lamp clean it with a cloth and a little denatured alcohol Wipe the lamp off before installing Be sure that the wires dont touch the lamp Reinstall the fan Close the cover Done Fig 1 Use 1 4 Turn to loosen the Fig 2 Use 1 4 Turn to loosen the screws and take out four screws and open the cover the fan e gt EN Fig 4 Unplug all the connect wires over the lamp and wear anti s
17. eset to factory settings and exit menu mode Home Position Adjustment Press MENU button into menu mode then press ENTER button for about 3 seconds into offset mode to adjust the home position Select the function by ENTER button Use UP and DOWN button to choose the submenu press the ENTER button to store and automatically return to the last menu Press MENU button to exit 128 127 128 127 0 255 128 127 128 127 0 255 Offset Menu 128 127 Zoom 0 255 Focus 0 255 Frost 0 255 BRITEQ 12 18 BTX BEAM 5R ENGLISH OPERATION MANUAL Pan Enter offset mode Select Pan press ENTER button to confirm the current position will blink on the display use UP and DOWN buttons to offset the value from 128 to 127 press ENTER button to store Press MENU button to exit Tilt Enter offset mode Select Tilt press ENTER button to confirm the current position will blink on the display use UP and DOWN buttons to offset the value from 128 to 127 press ENTER button to store Press MENU button to exit shutter Enter offset mode Select Shutter press ENTER button to confirm the current position will blink on the display use UP and DOWN buttons to offset the value from O to 255 press ENTER button to store Press MENU button to exit Color Enter offset mode Select Color press ENTER button to confirm the current position will blink on the display use UP and DOWN buttons to offset the value from 128 to 127 press ENTER b
18. f the LCD display POWER BATTERY Battery status DMX signal Buttons right side of the LCD display MENU To enter move back or leave the menu Y DOWN ENTER Confirm the desired function Button Shortcuts There are 4 different shortcuts to access specific functions without the need for using the setup menu While the screen displays the standard window see right the user can press the following button combinations e Lamp on Press MENU and UP together during 3s DMX Address Base 30 C e Lamp off Press MENU and DOWN together during 3s O O e Reset Unit Press MENU and ENTER together during 3s e Reverse display Press UP and DOWN together Md 1 19Ch Connections e DMX input output For DMX 512 operation use good DMX cable with 3 or 5 pin XLR connectors to link the units together e PowerCon out input The Powercon in out connectors allow the user to daisy chain up to 15 units on the same 20A power line While connected to a 16A power line only 12 units can be connected e Power Switch The BTX BEAM 5R uses a circuit 6A breaker instead of a usual fuse if the circuit breaker shuts down for any reason the user can simply put the switch back on BRITEQS 3 18 BTX BEAM 5R ENGLISH OPERATION MANUAL LAMP RE PLACEMENT In case of replacement of the lamp or maintenance do not open the fixture within 10 minutes until the unit cools down after switching off Always unplug the unit before servicing Always use the same typ
19. firm current mode will blink on the display press UP DOWN buttons to select No Pan or tilt s position will not feedback while they are out of step or Yes pan tilt will feedback if they are out of step press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode BL O P T Moving Blackout while pan tilt moving Select BL O P T Moving Press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select No normal while pan tilt are moving or Yes blackout while pan tilt are moving press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode BL O Color Change Blackout while change color Select BL O Color Change press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select No normal while the color is changing or Yes blackout while the color is changing press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode BL O Gobo Change Blackout while change gobo Select BL O Gobo Change press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select No normal while gobo is changing or Yes blackout wh
20. formity has been established and the relevant statements and documents have been deposited by the manufacturer e This device was designed to produce decorative effect lighting and is used in light show systems e An incredible powerful moving beam projector based on the legendary Philips MSD Platinum 5R lamp e The advanced optics guarantee an incredibly bright beam with excellent specs e Brightness 200 000lux 10m and 60 000lux 20m e Zoom 1 3 8 e DMX controlled electronic focus e Frost filter e 17 sharp gobos open e 14 carefully selected diachronic colors open e Very fast mechanical dimmer shutter e Different strobe functions e Remote lamp on off control e The very fast pan tilt movements 540 270 assure very dynamic show programming e 8 or 16bit resolution pan tilt resolution with position correction e The matrix LCD display assures easy navigation in the different setup menus e Battery backup makes it possible to configure the machine while the machine is not connected to the mains Different DMX channel modes for maximum flexibility Easy firmware updates keep your machine up to date at all times optional firmware updater needed Remote DMX addressing Neutrik 3pin amp 5pin in outputs for maximum flexibility in a professional environment Neutrik Powercon in outputs up to 15 units can be daisy chained for easy installation BEFORE USE e Before you start using this unit please check if there s no transportation dama
21. ge Should there be any do not use the device and consult your dealer first e Important This device left our factory in perfect condition and well packaged It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual Any damage caused by mishandling is not subject to warranty The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual e Keep this booklet in a safe place for future consultation If you sell the fixture be sure to add this user manual Check the contents Check that the carton contains the following items e Operating instructions e BTX BEAM 5R e 2x omega Brackets e Powercon cable BRITEQ 1 18 BTX BEAM 5R ENGLISH OPERATION MANUAL SAFETY INSTRUCTIONS CAUTION CAUTION To reduce the risk of electric shock do not remove RISK OF ELECTRIC SHOCK eN the top cover No user serviceable parts inside Refer servicing ee NOT OPEN to qualified service personnel only The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance servicing instructions in the literature a
22. he unit e In order to prevent electric shock do not open the cover Apart from the lamp and mains fuse there are no user serviceable parts inside e Never repair a fuse or bypass the fuse holder Always replace a damaged fuse with a fuse of the same type and electrical specifications e In the event of serious operating problems stop using the fixture and contact your dealer immediately SS z SS e e Va Y 3 BRITEQS 2 18 BTX BEAM 5R ENGLISH OPERATION MANUAL e The housing and the lenses must be replaced if they are visibly damaged e Please use the original packing when the device is to be transported e Due to safety reasons it is prohibited to make unauthorized modifications to the unit Important Never look directly into the light source Don t use the effect in the presence of persons suffering from epilepsy DESCRIPTION 1 Control panel 2 Head 3 Arm 4 Tilt arm self locking handle 5 pan self locking handle 6 Handle 7 Base Caution The head and arm must be unlocked before operation e Tilt mechanism locks and releases every 45 e Pan mechanism locks and releases every 90 Control Panel Front view control panel Rear view connections i E LEDs left side o
23. ile gobo is changing press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode Lamp Setting Enter menu mode select Fixture Setting press ENTER button to confirm use UP and DOWN buttons to select On Off State Power on Off Via DMX On if DMX on Off if DMX off Cooling Mode Ignition Delay or Low Power Delay On Off Turn on off the lamp Select On Off press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select On lamp on or Off lamp off press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode State Power On Lamp state while power on Select State Power On press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select On Lamp strike during the startup reset or Off Lamp is off at the startup press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Off Via DMX Turn off the unit via DMX controller Select Off Via DMX press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select Yes enable turn off lamp via DMX or No disable turn off lamp via DMX press BRITEQS 9 18 BTX BEAM 5R ENGLISH OPERATION MANUAL ENTER butto
24. inute after exiting menu mode press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode Backlight Intensity Select Backlight Intensity press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to adjust backlight intensity from 1 dark to 10 bright press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode Temperature Unit Select Temperature Unit press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select C or F press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode BRITEQS 10 18 BTX BEAM 5R ENGLISH OPERATION MANUAL Display Warning Select Display Warning press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select No display does not show the warning when the unit goes wrong or Yes display will show the warning when unit goes wrong press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode Fixture Test Enter menu mode select Fixture Test press ENTER button to conf
25. irm use UP and DOWN buttons to select Auto Test or Manual Test Auto Test Select Auto Test press ENTER button to confirm the unit will run built in programs to automatically test pan tilt color gobo gobo rotation shutter dimmer prism prism rotation frost focus and lamp on off Press MENU button back to the last menu or exit menu mode after auto test Manual Test Select Manual Test press ENTER button to confirm the current channel will show on the display use Up and DOWN buitons to select channel press ENTER button to confirm then use UP and DOWN buttons to adjust the value press ENTER button to store the fixture will run as the channel value indicates Press the MENU buiton to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode All channel values will become 0 after exiting Manual Test menu Fixture Information Enter menu mode select Fixture Information press ENTER button to confirm use UP and DOWN buttons to select Fixture Use Time Lamp On Time or Firmware Version Fixture Use Time Select Fixture Use Time press ENTER button to confirm fixture use time will show on the display press MENU button to exit Lamp On Time Select Lamp On Time press ENTER button to confirm lamp on time will show on the display press ENTER button to confirm use UP and DOWN buttons to select Exit or Reset Time press ENTER button to confirm Press the MENU button to go ba
26. me wires are defect Pan Reset Error Pan Encode Error Tilt Reset Error Tilt Encode Error Shutter Reset Fail Dimmer Reset Fail Color Reset Fail Gobo Reset Fail and Frost Reset Fail They may appear when turning on or resetting the unit or some parts such as board P C are damaged Please contact a qualified person for maintenance BRITEQS 17 18 BTX BEAM 5R ENGLISH OPERATION MANUAL SPECIFICATIONS Mains Input AC 100 240V 50Hz Power consumption 290 Watt Fuse 250V 6A circuit breaker Sound Control none DMX connections Movement Dimmer Shutter 3pin amp 5pin XLR male female Pan 540 Tilt 270 Pan Tilt position lock for transporting protection Mechanical dimmer Color wheel 14 fixed colors Gobo wheel 17 fixed gobos Effect 8 facet rotating prism Frost Zoom From 1 3 82 Focus Electronic DMX channels used 19 channels Lamp Philips MSD Platinium 5R 8000K Size 415 x 344 x 497 5 mm Weight 19 kg OOO O SE dx Gobo1 Gobo2 Gobo3 Gobo4 Gobo5 Gobo6 Gobo7 Gobo8 Gobo9 CISNE zA Gobo10 Gobo11 Gobo12 Gobo13 Gobo14 Gobo15 Gobo16 Gobo17 White Distance m 1 Spotdia m3 8 9 4 0 gt COAT 0 20 7 Every information is subject to change without prior notice You can download the latest version of this user manual on our website www beglec com BRITEQ 18 18 BTX BEAM 5R INNE LIGHT RESEARCH WWW BRITEQ LIGHTING COM Copyright 2012 by BEGLEC N
27. n to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode PS When you operate the unit via DMX controller set the value of channel special function to lamp off after 5 seconds the lamp will be switched off On If DMX On Lamp turns on when DMX signal is detected Select On If DMX On press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select Yes Lamp turns on when DMX signal is detected or No keep the default setting press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode If the lamp is off via DMX signal you can reconnect the DMX controller to switch the lamp on Off If DMX Off Lamp turns off when DMX signal is off Select Off If DMX Off press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select Yes Lamp turns off when DMX signal is cut off press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode Ignition Delay Delay time between power on and lamp on Select Ignition Delay press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to adjust the delay time from OS to 255S press ENTER but
28. t in overheating The operator has to make sure that the safety relating and machine technical installations are approved by an expert before using them for the first time The installations should be inspected every year by a skilled person to be sure that safety is still optimal Installation 1 Fix the Truss hooks 1 to the Omega clamps with screw and locking nut 2 Fasten the omega clamps 2 on the bottom of the base by inserting quick lock fasteners 3 into the holes of the base and tighten fully clockwise 3 Hang the fixture on the truss 4 using the hooks and fasten the screws 5 Fasten the safety cable 6 through the bottom of the base and over the support ELECTRICAL INSTALLATION ADDRESSING a important The electrical installation should be carried out by qualified personal only according to the regulations for electrical and mechanical safety in your country Electrical installation for two or more units in DMX mode e The DMX protocol is a widely used high speed signal to control intelligent light equipment You need to daisy chain your DMX controller and all the connected units with a good quality balanced cable e Both XLR 3pin and XLR 5pin connectors are used however XLR 3pin is more popular because these cables are compatible with balanced audio cables Pin layout XLR 3pin Pint GND Pin2 Negative signal Pin3 Positive signal Pin layout XLR 5pin Pint GND Pin2 Negative signal
29. tatic gloves take on the lamp Put the new lamp in place BRITEQS 4 18 BTX BEAM 5R ENGLISH OPERATION MANUAL OVERHEAD RIGGING e Important The installation must be carried out by qualified service personal only Improper installation can result in serious injuries and or damage to property Overhead rigging requires extensive experience Working load limits should be respected certified installation materials should be used the installed device should be inspected regularly for safety e Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing Locate the fixture in a well ventilated spot far away from any flammable materials and or liquids The fixture must be fixed at least 50cm from surrounding walls e The device should be installed out of reach of people and outside areas where persons may walk by or be seated Before rigging make sure that the installation area can hold a minimum point load of 10times the device s weight e Always use a certified safety cable that can hold 12times the weight of the device when installing the unit This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails The device should be well fixed a free swinging mounting is dangerous and may not be considered Don t cover any ventilation openings as this may resul
30. the internal optics at least every 90 days Attention We strongly recommend internal cleaning to be carried out by qualified personnel TROUBLESHOOTING The following points are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The unit does not work no light the fan does not work 1 Check the power cable and the circuit breaker 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if they are linked properly 2 If the DMX LED is on and no response to the DMX controller check the DMX address and the channel mode 3 If you have intermittent DMX signal problems check the pins on connectors or on the PCB of the unit or the previous one Try to use another DMX controller Check to see if the DMX cables run near or alongside high voltage cables this may cause damages or interferences to DMX interface circuit gd a C One of the channels is not working well 1 The cable between the motor and the PCB should be defect 2 The motor s drive IC on the PCB might be defect D The lamp is cutting out intermittently 1 The lamp is not working well Check if the mains voltage is either too high or too low 2 Internal temperature may be too high Check if the replacement of fan is needed on the head m If The pan belt is broken Turn off
31. ton to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode Low Power Delay Delay time between reduce lamp power and shutting off the unit Select Low Power Delay press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to adjust the delay time from Os to 255s press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode If you set the low power delay time to 3s the lamp will run in half power 3 seconds after the shutter is totally closed Display Setting Enter menu mode select Display Setting press ENTER button to confirm use UP and DOWN buttons to select Display Inverse Backlight Auto Off Backlight Intensity or Temperature unit and Display Warning Display Inverse Select Display Inverse press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select No normal display or Yes inverse display press ENTER button to store Press the MENU button to go back to the last menu if you leave the unit unused for one minute it will automatically exit from menu mode Backlight Auto Off Select Backlight Auto Off press ENTER button to confirm current mode will blink on the display use UP and DOWN buttons to select No display always on or Yes display goes off one m
32. utton to store Press MENU button to exit Gobo Enter offset mode Select Gobo press ENTER button to confirm the current position will blink on the display use UP and DOWN butions to offset the value from 128 to 127 press ENTER button to store Press MENU button to exit Prism Enter offset mode Select Prism press ENTER button to confirm the current position will blink on the display use UP and DOWN buttons to offset the value from O to 255 press ENTER button to store Press MENU button to exit R Prism Enter offset mode Select R Prism press ENTER button to confirm the current position will blink on the display use UP and DOWN butions to offset the value from 128 to 127 press ENTER button to store Press MENU button to exit Zoom Enter offset mode Select Zoom press ENTER button to confirm the current position will blink on the display use UP and DOWN buttons to offset the value from O to 255 press ENTER button to store Press MENU button to exit Focus Enter offset mode Select Focus press ENTER button to confirm the current position will blink on the display use UP and DOWN buttons to offset the value from O to 255 press ENTER button to store Press MENU button to exit Frost Enter offset mode Select Frost press ENTER button to confirm the current position will blink on the display use UP and DOWN buttons to offset the value from O to 255 press ENTER button to store Press MENU button to exit
Download Pdf Manuals
Related Search