"user manual"
Contents
1. For example 710 134xxxxxxxx 0000 Note All alarming information thereafter including SOS low power electronic fence etc will be returned to such number 7 2 3 Alarm number setting function Send the command in form of SMS through mobile phone to the terminal After the setup is successful after sending the SMS the mobile phone will receive the config OK response message returned from the terminal Setup format 711 Call 1 Call 2 Call 3 0000 For example 11 198140562 F 866 72383 15814056 888 0000 ty 4y ty lt y Send command to the terminal a a a A The terminal will return confirmation message to the mobile phone Description After the setting is successful press the SOS key then the terminal will circularly dial the set phone until it is connected 7 2 4 SOS Function If the monitoring number 1 e the phone in Item 3 is set when the ward is in emergency press the SOS key for 3s then terminal will firstly play a piece of alert tone and then send a piece of alarm message to every pre saved number then circularly dial the three pre saved numbers until getting connected At the same time the terminal activates the GPS function after succeeding the terminal will report the current location to the center Format of sending alarm message 35682303 1017473 0 0000 SOS 2 26280E4E 1 1354 6567 E 2232 7841 N 005 82 1 19 180310 061616 7 2 5 Regular Upload Interval Setup The defa2. 4 20 bits Log user name letters or digits 4 20 bits in Log password letter or digits 4 20 bits in terminal password 4 bits and send it to the terminal after executing this command the terminal will automatically restart and connect to GPRS with APN set Command example 1 802 cmnet 0000 Command example 2 802 CCDLEN QIUXIA 21 RX0000 0000 After this command is executed APN will be CCDLEN the login user name is QIUXIA 21 and login password is RX0000 Note The default APN of this product is CMNET 7 2 9 Electronic Fence Function 1 GPS Fence Function Set fence format command number 751 fence radius sampling interval longitude latitude user password Ht For example 75 1 500 5 22 5442N 113 91E 0000 After the setup is successful the setting mobile phone will receive a piece of config ok command Then when the ward leaves this area the terminal will send the alarming information of being out of the fence to the center number 2 Fence Reading Function Send commands to the terminal command number 752 user password 4 digits after the command is set successfully the terminal will read the data of the module fence working status and return message to the sending 13 mobile phone or PASSWORD ER if the password is wrong For example 752 0000 Return open 1 lat 11456 209400 Ing 2233 470100 distance 500 time 5 status 2 Where open indicates fence open Open 0 indicates fence clo
3. 50 5a 2 6 a a Functional Description When listening to FM radio you need to pull out the FM antenna Volume key During call listening to FM radio etc to adjust volume just press this key FM shortcut key Push the key upward to open FM radio and downward to close it Answer and dial key Dial a call or receive a call in standby press this key to enter the latest call log 6 Reoeiver Voice ring tone and FM output Screen Adjust menus the left and right direction keys are for Enter and Back Power on off key End or refuse a call In operation back to the previous level i e Cancel or Back On the switch off state press this key long to switch on the phone On the standby interface press this key long to switch off the phone On the non standby interface press this key long to back to the standby interface in shortcut way On the Edit interface press key to input special symbols and press the key to switch input modes ce 14 _ Flashlight switch 15 _ Keypad lock switch te SOS key In switch on off state press this button for 3 for SOS refer to 7 2 2 7 2 3 for details 2 4 How to Insert the SIM Card Please insert the SIM card along its SIM card slot direction align the cut corner of the SIM card with the cut corner of the slot and make sure that the SIM card has been inserted into its proper position 2 5 Battery 2 5 1 Install the Battery Open the battery cover insert the SIM ca
4. GPS Safety Monitoring Mobile Phone User Manual Phonebook Welcome to use our mobile phone Thank you for choosing our GPS safety monitoring mobile phone This mobile phone represents the perfect combination of GSM and GPS technologies It is characterized by streamline fashionable profile design simplicity and elegance it fully shows the fashionable personality With large capacity phonebook SMS alarm clock call center phone settings FM radio GPS hang up state emergency alarm etc it can help you enjoy a rich and colorful life e Before use be sure to read this manual carefully The content of this manual may be different from the real object so the latter shall prevail Should any update on this phone and its accessories we will not make further notice 1 Related Requirements Related requirements for the use of the phone Never use the phone at too high and too low temperature In order to ensure call quality try to avoid using the phone too close to common phone TV set radio office automation etc In order to keep accurate positioning be sure to use the GPS function of this phone in an open place Related requirements for the use of the battery The battery shall be placed in the cool well ventilated and direct sunshine free place If the battery is used up for long it will be unable to be charged If the phone is idle for long please regularly charge it The battery is consumable All the batteries have cer
5. a registered user This device supports the dual positioning mode of GPS and GSM GPRS Please use this device in a legal area any illegal consequence will be borne by the user 14
6. all preventing the transmission of Call cut off or noise l l signals interference in call In fast movement The signal may have momentary interruption during base station switching Please slow down and do not move violently during call The plug of the charger is not Insert the plug again inserted properly Unable to charge the b The power cord of the charger is Check the connection attery disconnected The battery is aged 7 About GPS 7 1 Introduction to GPS related Functions GPS individual positioning High sensitivity new workmanship and the most advanced GPS chip Can work effectively in limited space such as the remote and narrow places in a city Low energy consumption Fast signal capturing Supports single positioning and continuous tracking Supports alarming and remote monitoring Supports fast dial button Supports the location information inquiry by SMS and Internet May monitor without disturbing the tracked person and realizes real time tracking Can position the holder by call or mobile phone SMS In emergency press the SOS button to have an accurate positioning Supports SOS key alarm in switch off state 7 2 Commands Corresponding to and Operation Method of Basic Functions 7 2 1 Location Inquiry 1 SMS Inquiry Create 988 password command defaulted password as 0000 via mobile phone and send it to the terminal mobile phone number after successful sending the guardian s mob
7. ated you need to input SIM password press the Left Function Key to confirm and enter the standby interface 2 If the phone protection is activated you need to input the phone password press Left Function Key to confirm and enter the standby interface Switch off On the standby interface press the Switch off Key to switch off the phone 3 2 Standby Shortcut Tips On every edit and function interface press the Power on off key to directly back to the standby interface On the standby interface press the Up Down Direction Key to enter the main menu On the main menu press the Dial Key to enter the corresponding module On the standby interface press the Dial Key to enter the list of the latest received dialed calls On the standby interface press the Power on off key to enter the phonebook menu On the standby interface press the Left Direction Key to enter the interface of SMS On the standby interface press the Right Direction Key to enter the Profiles menu 3 3 Keypad Lock In order to avoid touching the keypad carelessly and thus causing wrong operation you may lock the keypad of the phone In switch on state push the keypad lock switch downward to lock the keypad In the locked keypad state push the keypad lock switch upward to unlock the keypad 3 4 Adjust Receiver Volume Press the left volume adjustment key to adjust the receiver volume 3s after the volume is adjusted the screen will automat
8. ically back to the call duration page 3 5 Word Input GPS safety monitoring mobile phone provides such input modes for you as intelligent Pinyin input letter input English input number input and symbol input The defaulted input mode is the intelligent Pinyin input mode You may set input mode on the phone Press the Key to switch input modes and the input state will be displayed on the right upper corner of the screen The keypad definitions in the input mode are as follows Enter Key Confirms the selected Pinyin Chinese characters or symbols Back Key Exits from the current input state Up Direction Key Down Direction Key Moves the cursor up and down Key Inputs punctuations Key Switches input modes 0 Key 9 Key Input digits 4 Functional Description 4 1 Phonebook The phonebook is used to store your phone numbers and it includes phone phonebook and SIM phonebook The phone phonebook can hold 200 entries while the SIM phonebook capacity depends on the actual SIM card Via Main Menu Phonebook or on the standby interface press the Left Direction Key to enter the phonebook in a shortcut manner 1 Search Contacts You may search phone numbers according to names You need not to input all of the name but part to search the phone number 2 Add Contacts You may add new contacts into the phonebook 3 Copy All You may copy the phone numbers on the SIM card to the phone or vice versa 4 Dele
9. idden dialing and password revision 6 Restore factory settings Input the password to restore the factory settings 4 5 Kit Via Main Menu Kit display Alarm Clock At most this phone may set 5 alarm clocks at the same time Via the alarm clock settings on the tool bar of the main menu display the list of alarm clocks choose one alarm clock press the Enter Key to enter alarm clock settings 5 Phone Maintenance Wipe off the common dirt with dry and soft cloth If too much dirt twist the soft towel with neutral detergent dry and gently wipe off dirt and then wipe the phone with dry soft cloth Do not use hard cloth and benzene thinner etc to wipe the phone otherwise phone surface scratch fade or color change may occur 6 Troubleshooting When feeling abnormal during operation please restore factory settings and refer to the following solutions If the problem cannot be solved please contact the distributor or the service provider Possible Causes The battery is used up Charge the battery The Switch on Key is not Press the Switch on Key for more than 2s Unable to switch on pressed long enough The battery is not installed Install the battery correctly properly Out of the service area Move to the place with signals Unable to dial a call Wrong phone number Check the phone number Too weak signals Move to the place with strong signals There are buildings around Change to another place for c
10. ile phone will receive a piece of word message See the flow as follows 9880000 REAY ESATA Se W4t F AE39 JE FE RS www 140K A The terminal will return confirmation message to the mobile phone a a Send command to the terminal By the same means send the command 987 password to the terminal then the terminal will return one piece of website message The guardian may inquire the location information of the ward attached with local map through this website message In the same way send the command 666 encrypted password to the terminal then the terminal will return a piece of latitude and longitude message and a piece of detailed address message 10 2 Platform Inquiry Step 1 Log onto the platform JK JY100 COM Step 2 Click the terminal of the ward then the map will aid the location of the ward sme saag 20 re itith WV en E gt BRERA DNU r AREH KEHE e Kat o Aerts f RRA a GPS Tracker 0000 p4 ETR le RRAS a HBE l Te OP RRAN FSRABLSSBaSRwHs EE 390K HRS se E 91 kmh Ale pam y5 geteptial 2010 1 22 19 38 40 ai Ef Radar ABS vet ECKE SHAS E Re FRR s27 IG ALG ae ve 7 2 2 Setup of Center Number Set the center number by means of SMS through mobile phone After the setup is successful then the mobile phone sending the SMS will receive the config OK response message from the terminal Command format 710 center number user password
11. on Key to select Send to input the phone number Or press the Left Function Key options to choose phonebook enter the page of selecting phone number on the phonebook press the Enter Key Left Function Key to introduce the number of such contact 3 Select and Save You may save the edited SMS into the draftbox 4 Send After the recipient number is input press the Left Function Key to send the SMS 4 2 2 Inbox 1 Via Main Menu gt SMS Inbox display the list of the received SMS 2 Choose the SMS item and then press the Left Function Key to choose the operation item and carry out it 4 2 3 Outbox Via Main Menu SMS Outbox display the SMS having been sent successfully 4 2 4 SMS Settings Via Main Menu SMS SMS Settings you may have such options as mode settings status settings preferred location preferred connection 4 3 Call Center Call log includes missed calls received calls and dialed calls You may enter the call center via Main Menu gt Call Log 4 4 Phone Settings Via Call Settings you may set the normal functions of the phone Via Main Menu Settings you may have the following settings 1 Time amp date Set the time and date for the phone 2 Timed switch on off Switch on off the phone within the set time by the user 3 Language Chinese and English 4 Network settings Network selection etc 5 Security settings SIM lock phone lock keypad lock fixed dialing forb
12. rd properly install the battery and then restore the battery cover 2 5 2 Charge the Battery About charging 1 Insert the charging plug of the charger into the charging port of the phone and the other end of the charger into the 220V power socket In such case the phone backlight will be lit up the battery icon will rolling ee ee a T Charging C Charged 2 When the battery icon of the phone stops flickering it will indicate that the charging is over and the screen will display Charged Charge with the phone on 1 Insert the charging plug of the charger into the charging port of the phone and the other end of the charger into the 220V power socket In such case the phone backlight will be lit up the battery icon will flicker and the battery icon on the right of the screen will start flickering e Tips For the battery of the newly bought mobile phone or the new replacing battery do not charge it until it is completely used up It is recommended to charge the battery for above 12h for the first three times in order to ensure the service life of the battery The charging with the phone on will not affect the normal call dial and reception but consume more power than 5 usual and thus it will take more time to charge the battery 3 Basic Operation 3 1 Switch on off Switch on Press the Switch on Key to switch on the phone and enter the standby interface Tips 1 If the SIM protection is activ
13. sed lat 11456 209400 latitude Ing 2233 470100 longitude distance 500 fence radius time 5 sampling interval status 2 terminal has obtained valid satellite data fence works normally status 1 fence open but there are no valid satellite data have been received status 0 no electronic fence is set 3 Server center address command Command name 803 server address port password Example 803 jk jy 100 com 80000 0000 4 Function of Canceling Fence Command name command number 760 user password 4 digits Example 760 0000 After the terminal receiving this command all fence settings will be cancelled Advice Do not set GSM fence and GPS fence at the same time 7 2 10 Auxiliary Functions 1 901 Command of reading user parameters 2 902 Command of reading GPRS parameters 3 904 GPRS connection command 4 905 GPRS disconnection command 7 2 11 Server setting command Format 803 IP address port user password Example 803 WEB2 80000 0000 8 After sale Service For more information about after sale service please refer to the attached After sale Service Manual Notices This device is of non waterproof design This device must work with the cooperation of GSM GPRS network Make sure that the SIM card has sufficient balance in order to avoid inconvenience in use This device will not be able to work in case of power off and out of the service area even if you are
14. tain service life When the battery is charged repeatedly but cannot improve its performance it will indicate that the battery has been damaged and should be replaced Never throw the waste battery together with rubbish When dealing with the waste battery always abide by the regulations of the local competent authority Charging requirements Please do not charge your phone at such places the sunshine can reach directly the outer temperature is below 5 C or higher than 40 C Humid and dusty places or vibrating places might cause malfunction near television radio or other electrical devices might affect the image and sound of these devices 2 Use Notices 2 1 Check the Phone and Accessories Unpack the mobile phone package and check if the phone and its accessories are complete In case of any incompletion please consult the local distributor e Ix mobile phone e x battery e Ix charger e 1x user manual e Ix certificate of conformity 2 2 Mobile Phone Specifications 2 2 1 Accessory Specifications Input AC220V 4 20 50Hz 50mA Charging time 12h for the first three times and 3 6h thereafter 2 2 2 Technical Specifications Work frequency 850 900 1800 1900MHZ Continuous call duration About 5h Continuous standby duration 7 days GSM standby The standby duration and call duration depend on the local network and GPS application 2 3 Appearance Pell ER Bia lt gt iy 221
15. te You may delete the phone phonebook or the SIM phonebook 5 Phonebook Settings You may set the preferred storage location or phone list 4 1 1 Search Search the contacts in the phonebook according to names Fast search In the phonebook list you may localize the contact according to the first Pinyin letter of the name or the first letter of the English name For example in phonebook list to search Li Si press the 5 Key JKL three times to localize the contacts beginning with L 4 1 2 Add Contacts 1 Enter the phonebook and choose Add to add new contacts into the phonebook 2 The storage location includes phone phonebook and SIM phonebook If phone phonebook on the editing page of adding contacts in turn input name and phone number 3 Press the Left Function Key to save the contacts 4 1 3 Copy Copy You may copy all numbers on the SIM card to the phone or vice versa 4 1 4 Settings Settings You may set the preferred location of the phonebook and the content displayed on the list 4 2 SMS This phone supports the delivery of SMS to many parties totally you can send SMS to 10 recipients at a time Every SMS may contain at most 58 Chinese characters or 116 English words digits and symbols 4 2 1 Create SMS 1 Create Via Main Menu SMS Create enter the SMS editing interface for SMS editing refer to the input mode 2 Choose Number After the content of the SMS is input completely press the Left Functi
16. ulted factory upload interval of this device is 2 minutes for getting the point and 4 minutes for uploading one piece of positioning information The user may change such parameter according to actual demand Command format command number 730 Sampling interval Pieces of uploads User password For example 730 20 4 0000 Note The parameter 20 indicates getting one point every 20s after getting points accumulatively for 4 times upload one piece of positioning information with the upload interval as 20 4 80s The user may change this parameter as the case may be 7 2 6 Function of Changing Password Send the SMS 770 User new password User old password by mobile phone to the terminal number after successful sending the mobile phone with such setup will receive one piece of config OK response information as shown in the following figure 12 EG 83070 A 70 12340000 CONFIG OK vU Send command to the terminal YEG The terminal will return confirmation message to the mobile phone 7 2 7 Low Voltage Alarming Function If the terminal of the ward has a very low power and needs to be powered off the terminal of the ward will automatically upload one piece of low voltage alarming command to the monitoring center number SMS format 35682303 1017473 038888 LPD 1 26280E4E 11354 6567 E 2232 7841 N 005 82 119 1803 10 061616 7 2 8 Set APN Command Create the SMS 802 APN letters or digits
Download Pdf Manuals
Related Search