SGS E1
Contents
1. agnetic Compatibility speed control of single phase motors of the fans and ventilation units We hereby declare that the following product complies with the essential The speed is controlled by means of touching the button ON OFF and two protection requirements of Electromagnetic Council Directive 2004 108 speed control buttons located on the sensor glass panel EC 89 336 EEC and Low Voltage Directive 2006 95 EC 73 23 EEC and CE marking Directive 93 68 EEC on the approximation of the laws of the SAFETY RULES Member States relating to electromagnetic compatibility The manufacturer hereby warrants normal operation of the product over the period of 2 years from the retail sale date provided observance of the installation and operation regulations In case of failure due to manufacturing fault during the warranty period the consumer has the right for the device repair or exchange The replacement is offered by the Seller If case of no confirmation of the sale date the warranty period shall be calculated from the manufacturing date The MANUFACTURER shall not be liable for any damage resulting from STORAGE AND TRANSPORTATION RULES any product misuse of or gross mechanical interference with it Transportation is allowed by any vehicle provided the product is The MANUFACTURER is not responsible for the damages resulted due to transported in the original package and is protected against weather and the use of third party equipment or to third party eq2. p the button within 5 seconds until the light indicator displays 50 of the operation range That differentiates the setup mode from the operation mode Ventilation equipment operates at the maximum speed 2 Set the rotation speed by pressing the buttons lt Or D The set speed level is displayed with the LED light indicator l 3 Save the selected set point by pressing the button ON To activate the fan and activate its set operation mode press the l HE button o When setting the minimum speed press the button lt to save the current set point Every time you enter the setup mode the maximum speed is set by default no matter of the previous set point Fig 2 Mounting Mounting seguence of the sensor speed controller fig 2 1 Carefully undo the latches on the front panel with a screwdriver 2 Remove the back panel 3 Route the cable to the installation place of the speed controller 4 Fix the back panel to the wall through the fixing holes 5 Install the front panel on the latches 110 240V 50 60 Hz M ventilation equipment motor Fig 3 Wiring diagram 11 Fig 4 Sensor speed controller control BLAUBERG Ventilatoren SGS E1 v 2 2 EN indd 3 23 09 2015 11 56 23 ACCEPTANCE CERTIFICATE Sensor speed controller SGS E1 N is recognizes as serviceable Approval mark Manufact
3. perature humidity Service life Protection Weight g mm range range Rating Hz V A C SGS E1 230 1 035 1 fom 10upto from5up 1 IP 30 138 45 to 80 operations BLAUBERG Ventilatoren SGS E1 v 2 2 EN indd 2 0 23 09 2015 11 56 22 O 00000 OUT OUT OUT OUT IN L4 13 L2 5 L 111 oe Fig 1 Overall dimensions MOUNTING WARNING Make sure that the device is not damaged Do not use a damaged device Do not install the device on an uneven surface While tightening the screws avoid overtightening not to damage the device CONNECTION TO POWER MAINS AN WARNING Cut off power supply to the speed controller prior to any operations with the speed switch All mounting and servicing operations are allowed for duly qualified electricians with valid electrical work permit for electric operations after careful study of the present operation manual For connection of the sensor speed controller to ventilation units and fans follow the wiring diagram fig 3 CONTROL I When connected to power mains the button glows dull blue 0 N N Press the button to activate deactivate the connected ventilation eguipment Press the button to decrease or the button gt to increase the motor speed Setting minimum rotation speed of the connected motor 1 Press and kee
4. sooo00 0000000000001 gop SENSOR SPEED CONTROLLER SGS E1 OPERATION MANUAL BLAUBERG Ventilatoren N O SGS E1 www blaubergventilatoren de BLAUBERG Ventilatoren GmbH is happy to offer your attention the sensor The storage environment must not be subjected to any aggressive and speed controller SGS E1 or chemical evaporations admixtures foreign objects that may provoke corrosion and damage connection tightness Store the product in an environment with minimized risk of mechanical NN damages temperature and humidity fluctuations at the ambient temperature The present operation manual contains technical description technical from 5 C up to 40 C data sheets operation and mounting guidelines safety precautions and warnings for safe and correct operation of the device Read carefully the operation manual especially the safety requirements MANUFACTURER S WARRANTY before mounting and start up of the device The product complies with the requirements according to the EU norms Keep the operation manual available as long as you use the device and directives to the relevant EU Low Voltage Equipment Directives EU Directives on Electromagnetic Compatibility The product complies with the requirements according to the on EU norms and directives to the relevant EU Low Voltage Equipment The sensor speed controller SGS E1 is designed for switching on off and Directives EU Directives on Electrom
5. uipment mechanical damages Store the delivered product in the manufacturer s original packing box in a dry ventilated premise Cut off power supply to the device prior to any operations All mounting and maintenance operations must be carried out by duly qualified electricians with a valid electrical work permit for electric operations after careful study of the user s manual Misuse of the device or any unauthorized modification are not allowed Follow the manual guidelines to ensure trouble free operation and long service life of the device AN WARNING WARNING The product is not allowed for use by children and persons with reduced physical mental or sensory capacities without proper practical experience Do not dispose in domestic waste The product contains in part material that can be recycled and in part substances that should not end up as domestic waste Dispose the product once it has reached the end of its working life according to the regulations valid in your country or expertise unless they are controlled or instructed on the product opera tion by the person s responsible for their safety Supervise the children and do not let them play with the product DELIVERY SET Y Sensor speed controller SGS E1 Y Operation manual v Packing box TECHNICAL DATA Table 1 Technical data Parameters Model Supply Max current Cable cross Operating Operating Ingress voltage 50 60 load section tem
6. uring date WARRANTY CARD ss SELLER SALES DATE REPRESENTATIVE IN EU BLAUBERG Ventilatoren GmbH Aidenbachstr 52a D 81379 Munich Germany BLAUBERG Ventilatoren Op el www blaubergventilatoren de SGS E1 v 2 2 EN a SGS_E1_v 2 2 EN indd 4 0 23 09 2015 11 56 23
Download Pdf Manuals
Related Search