Pet Remote Training Collar for 3 Dogs User Manual
Contents
1. points to ensure consistent contact 3 The collar receiver should fit snugly yet loose enough to allow on finger to fit between the strap and your dog s neck If the strap is too long for your dog cut off the excess length 4 Allow your dog to wear the collar for several minutes and then recheck the fit Check the fit again as your dog becomes more comfortable wearing the collar receiver Notice Please always install the Transmitter s battery BEFORE install the receiver s batteries because it is a wireless training system The Transmitter has to be power on and then 2 LAVA Electronics Inc Tel 1 909 923 8743 Email ismartpets qgmail com www lavasat com LAVA Electronics Inc Copyright 2009 2010 All Rights Reserved A N Good Pets Make happy Owners SmartPets the receiver is able to receive the code from transmitter It might not work if install the batteries incorrectly or did not match the receiver and transmitter correctly How to use the transmitter and receivers Press the A button the receiver A is in the work mode Press the B Button the receiver B is in the work mode Press the C Button the receiver C is in the work mode Button 1 4 are for 4 different audible tones Button 5 8 are for 4 different static shock Increase in static shock Notice Only for the C collar receiver the Button 5 8 are for the different static shock with audible tones only for C collar receiver We would recommend yo2. ce signals or signal screening around the actual remote control distance may vary 6 The lifetime of the batteries vary according as how often you use the product Therefore you should often check the batteries by watching the indicator light in the receiver and the indicator sign on the LCD screen of the transmitter 7 This product is for pet training Only by training the pet can understand d the intention of its owner Good effect can only be achieved after a period of training 8 This product is a wireless transmitting device you MUST NOT use the remote control system in places like petrol stations or hospitals where mobile phones are prohibited Patients using heart pacemaker are forbidden to use this product 9 The Electrodes have to direct contact with your pet s skin as it is very important to effective training 10 This product is only for Pet Training It is not a regular Pet Collar Please remove it from your pet at least 8 hours out of every 24 hours We would recommend you touse the Beep Mode first before starting the static shock and always start from the lowest level of static shock CE Made in China 4 LAVA Electronics Inc Tel 1 909 923 8743 Email ismartpets gmail com www lavasat com LAVA Electronics Inc Copyright 2009 2010 All Rights Reserved
3. e A N Good Pets Make happy Owners SmartPets Pet Remote Training Collar for 3 Dogs User Manual Model SP 403 This is an effective 3 pets training system specially designed for those who wish to train up to 3 dogs simultaneously and independently It features an easy to use transmitter 4 audible tones of different frequencies and 4 levels of static shock replaceable batteries and 200 meters range Contents e 1x Transmitter e 1x 6F22 9V Battery e 1x Antenna for transmitter e 1x3 Adjustable Collar Receivers e 3x 6V Batteries e 1x Test Light for checking static shock e 1x User Manual Quick start Guide Step 1 Prepare the Remote Transmitter Screw the antenna into place before using Do not operate the remote trainer without a transmitter antenna Follow the Positive and Negative signs inside the transmitter Insert the 9V 6F22 battery into the transmitter correctly Step 2 Prepare the Collar Receiver Insert the 6V 4LR44 battery into the receiver collar following the positive and negative signs The collar will beep when you install the battery into receiver correctly and LED indicated light will stay on for 2 second Collar is in the standby mode and ready to receive signal which will consume a small amount of electricity Step 3 Match Transmitter with the Collar Receivers 1 Press and hold A button on the transmitter The LED indicated light on the transmitter will stay on for about 2 seconds a
4. nd then turn off Keep holding the q LAVA Electronics Inc Tel 1 909 923 8743 Email ismartpets qmail com www lavasat com LAVA Electronics Inc Copyright 2009 2010 All Rights Reserved a AN Good Pets Make happy Owners SmartPets A button and wait until the LED indicated light of transmitter start blinking the transmitter is in the matching mode 2 Randomly pick the collar receiver that has same color as A button align the two blue paper dots matching point on the transmitter and the collar receiver as close as possible distance not over 2mm 3 You will hear one beep from the receiver and the LED indicated light keeps on for 2 second then turn off Release A button now and LED light on the LED indicated light on transmitter will turn off Repeat the above steps for Button B C and for the other two collar receiver Once matching finished all the collar receivers will work independently Step 4 How to Check the Static Shock Test Light 1 Use the Test Light attach on the both side of Electrodes Metal 2 Press Shock Button the TEST LIGHT will blink or keeps on Step 5 Adjust the collar to fit _your pets To ensure a proper fit please follow the steps below 1 Put the collar receivers on your pets 2 With your dog standing centre the Electrodes collar receiver where contact points are underneath your pet s neck touching the skin If your dog has a long or thick coat trim the hair around the contact
5. u to use the tone function first before starting the static shock and always start from the lowest level of static shock How to change the batteries It is important to check the battery regularly by monitoring indicated light to ensure the collar is working properly If the Receiver LED indicated light does not light up please replace the batteries of receiver If the Transmitter indicated light does not light up please replace the battery of transmitter Important 1 You need to re do the matching process every time after you replacing the battery either transmitter or collar receiver 2 The LED light on the transmitter will turn on when you press buttons to send signal to the collar receiver Please wait the LED light turns off before sending a new signal DO NOT hold the static buttons Button 5 8 too long 3 Except during the matching process DO NOT hold A B and C button for more than 3 Seconds to avoid changing of matched codes on the Transmitter 4 Ifthe transmitter is interfered and sends out wrong signals please re match it with the collar receiver 5 The valid distance of remote control means the straight line distance between the transmitter and the receiver without obstacles in between If there are 3 LAVA Electronics Inc Tel 1 909 923 8743 Email ismartpets qgmail com www lavasat com LAVA Electronics Inc Copyright 2009 2010 All Rights Reserved K N Good Pets Make happy Owners SmartPets interferen
Download Pdf Manuals
Related Search