User Manual
Contents
1. E Illuminator User Guide lt MES Cube Illuminator Range Models covered by this manual UFO CUBE DMX UFO CUBE DMX R Please read this manual fully before installing operating or performing maintenance on the illuminator unit Universal Fiber Optic Lighting LLC 6119A Clark Center Avenue Sarasota FL34238 Tel 941 343 8115 or 800 UFO 5554 Issue 1 Revised 17112014 www fiberopticlighting com INTRODUCTION Thank you for purchasing this UFO Illuminator Please read these instructions fully before connecting your unit to the electrical supply and keep them for future reference The UFO Cube illuminator is suitable for use with either glass or PMMA fiber optic harness The Cube is powered by a 100 240 VAC remote desktop power supply unit IMPORTANT THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED a Cube Illuminator Range INSTALLATION INSTRUCTIONS POWER SUPPLY REQUIREMENTS The LED Illuminator is powered from a multifunction multi voltage desk top Power Supply Unit Remove the 24V Desk Top PSU from its box This PSU is an IEC input device catering for UK European and USA mains supplies using the relevant power cord Universal Fiber Optics E CONNECTIONS There are 3 connections required the fiber port the mains supply cable and the DMX control cable The fiber2. Illuminator then replace and once the Indicator Light 4 lights touch button 5 within 3 seconds the Illuminator will blink twice slowly indicating that the Remote Controller is matched to the Illuminator Unmatching Remote from Illuminator Remove the power plug from the rear of the Illuminator then replace and once the Indicator Light 4 lights touch and hold button 5 within 3 seconds and the Illuminator will blink 9 times indicating that the Remote Controller is unmatched from the Illuminator Universal Fiber Optics I OPERATION Remote Controller Modes and Functions Mode Static White as asn All Colors sn fade Brightness Adjus table Speed Comment To revert to 1 Static White at any ue time touch Color Ring then Mode Color Ring control brightness adjust Color only not White To revert to 2 Color Ring at any time touch E Seo Not Adjustable Mode Buttons This is not a loop i e touching the Mode button will not eventually bring you back to Mode 1 To revert to Mode 1 either touch Mode button repeatedly to step back up through the Mode numbers or touch Color Ring then Mode Color Ring The Color Ring can be used to select individual colors by touching the ring and sliding your finger around the ring Brightness brightness can be increased or reduced in any mode using buttons 6 amp 7 Cycle S
3. Replace PSU Replace Illuminator Switch array on using RF remote control Replace Illuminator Replace batteries as per User Guide Check for another RF device in same area Remove and reinsert batteries as per User Guide place remote place Illuminator e eck mode programming and set to REMO o place batteries as per User Guide move and reinsert batteries as per User Guide place remote o place Illuminator Check mode programming and set to DMX Change address on illuminator or DMX controller Check DMX controller for correct setting Check cable connections and repair as necessary Change Illuminator Change address on illuminator or DMX controller to make 5 channels available Check addresses Check DMX controller channel values Reduce channel 5 value to lt 251 Change illuminator Carefully clean the LED lens with a dry cloth Clean fiber common end Ensure plugged in correctly and secured with locking screw TECHNICAL SPECIFICATIONS Description Details LED Power 35W Power Connection 2 1X 5 5 X 12mm Min Ambient Temperature 14 F 10 C Max Ambient Temperature 104 F 40 C Operating Environment Indoor Dry Fan 60mm 12V Crossflow LED Type Model RGBW LED Life 50 000 hours Control Functionality Manual RF Remote amp DMX DMX User Addressable 5 channels 0 255 RF Remote Range 98 30m depending on environment Si
4. QUIRED UNTIL REQUIRED PROGRAMME IS PROGRAMME IS DISPLAYED DISPLAYED STEADY DISPLAY ADY DISPLA PRESS PRESS ENTER ENTER BUTTON BUTTON FLASHING DISPLAY FLASHING DISPLAY Kel O Ez E E m PRESS ENTER ENTER BUTTON DONE DONE Universal Fiber Optics E STANDALONE OPERATION Function Effect ap color change between 052345617 ap color change between ors 1 2 3 4 Fade color change between ors 12345617 Fade color change between olors 2 3 4 5 6 f Fade color change between i j i isplay colors 1 2 3 4 i e slowly to next color Cube Illuminator Range DMX OPERATION DMX Channel Operation The Cube DMX occupies 5 DMX channels as detailed below Channel Function Values 0 225 0 225 022 MAINTENANCE Please Note that a record of all maintenance MUST be kept in the table below indicating what maintenance was undertaken and when This MUST be dated for warranty purposes Maintenance Undertaken Universal Fiber Optics a TROUBLESHOOTING Probable Causes Mains supply off Problem Illuminator dead LED indicator on desk top PSU not illuminated Loose mains plug PSU faulty Illuminator dead LED Loose DC plug indicator on desk top PSU illuminated but LCD display on Illuminator not illuminated PSU faulty Illuminator Faulty Illuminator no li
5. cy 2 4GHz Approved for use in UK Europe and USA Batteries With The LED Illuminator powered up as described above remove the rear cover on Remote Controller Taking care not to touch any of the front cover buttons insert the batteries If you touch the remote control buttons when inserting the batteries it WILL effect the operation of your Remote Control If you do accidentally touch any ofthe buttons remove the batteries and start again Once the batteries are inserted do not use the Remote Control for 3 seconds DO NOT TOUCH THE BUTTONS WHILST INSERTING BATTERIES Test remote control as detailed on the following page The Remote Controller is matched to the Illuminator at the factory If the Remote Controller is not matched or and additional or replacement Remote Controller is required carry out the Matching Remote to Illuminator instructions in the following text If a Remote Controller is to be removed from control of a Illuminator carry out the Unmatching Remote to Illuminator instructions in the following text B Cube Illuminator Range OPERATION Remote Operation lt 2 OFF 4 Indicator Light 3 Color Ring 5 Speed 6 Brightness N Mode 7 Brightness lt 10 Mode 8 Speed y No Description Function i Button dicato REMOTE CONTROLLER OPERATION Matching Remote to Illuminator Remove the power plug from the rear of the
6. ght output LED but LCD display on Illuminator is illuminated If programme Mode is set to REMO illuminator may have been switched off using RF remote control LED array driver faulty Remote batteries failing Another RF device causing interference RF remote controller RF remote control needs resetting range reduced RF remote failing Illuminator receiver failing Illuminator not in Remote mode Remote batteries failed Illuminator won t respond RF te control needs resettin to RF remote controller RF remote failed Illuminator receiver failed Illuminator not in DMX mode DMX address incorrectly set Not responding to DMX no rotating symbol on LCD display No DMX signal from controller Wiring fault on DMX cables connections DMX driver failure Not fully responding to DMX some but not all colors controllable no rotating symbol on LCD display Illuminator address out of range not 5 available channels on DMX controller Incorrect address set on illuminator or controller No values set in DMX channel Not responding to DMX no light output rotating symbol on LCD display Channel 5 value high 251 255 switching off the array LED array driver failed Unit needs cleaning Poor light output on fiber Fiber port connector not plugged in correctly Cube Illuminator Range Remedy Check supply and reinstate Check plugs Replace PSU Check plug Check PSU output
7. peed speed of color cycling in Modes 3 to 14 can be adjusted using buttons 5 amp 8 B Cube Illuminator Range OPERATION Remote Range Walk Test Once the Illuminator is fully installed carry out a complete range walk test and record the range in the table below This information is essential for maintenance purposes to determine if the range sensitivity is reducing and also to record dead areas within the Remote Controller s range due to RF obstructions and or RF interference NOTE Where a Illuminator has more than one Remote Control reduction in operating range may be experienced when both or multiple Remote Controls are used simultaneously Description Controller 1 Controller 3 Dead Areas Controller 2 Universal Fiber Optics PROGRAMMING PROGRAMME PROGRAMME PROGRAMME PROGRAMME DMX MASTER SLAVE DMX REMOTE ADDRESS PRESS PRESS PRESS PRESS UNTIL UNTIL UNTIL UNTIL PRESS UP BUTTON OR OR OR PRESS PRESS PRESS PRESS BUTTON BUTTON BUTTON BUTTON UNTIL CORRECT UNTIL CORRECT UNTIL CORRECT UNTIL CORRECT SETTING DISPLAYED SETTING DISPLAYED SETTING DISPLAYED ADY D AY STEADY DISPLAY STEADY DISPLAY lt C D lt ENTER ENTER ENTER ENTER BUTTON BUTTON BUTTON BUTTON DONE DONE DONE DONE E Cube Illuminator Range PROGRAMMING STANDALONE PROGRAMMES DISPLAY TIMER PRESS PRESS UNTIL UNTIL Um PRESS PRESS UP UP BUTTON BUTTON OR OR PRESS PRESS DOWN DOWN BUTTON BUTTON UNTIL RE
8. port should be connected first Connect and secure the fiber optic connector into the green collar and secure using the M5 locking screw Connect the IEC power cord into the Desk Top PSU and plug the mains plug into the electrical supply socket Switch on power The LED Indicator will illuminate and the illuminator is ready for use If no light is produced consult the TROUBLESHOOTING section For DMX control connect up the DMX control cables to the XLR sockets or the RJ45 sockets on the side of the Illuminator The pin out details for the plugs are shown below XLR CONNECTORS ON p PS LIGHT SOURCE gt e Pin 2 DMX Pin 12 Ground RJ45 CONNECTIONS RJ45 CLIP DOWN PINS UP Pin No 1 2 3 4 5 6 7 Color White Orange White White Green White Orange 8 Blue Brown 8 A DMX DMX Function HOT COLD Spare Spare Spare DMX XLR Pin2 1 WHITE JORANGE equivalent 2 ORANGE 3 WHITE GREEN 4 BLUE 5 WHITE BLUE Note It is recommended that a 1200hm terminating resistor be connected across DMX and DMX on the last illuminator on the DMX universe or cable run Cube Illuminator Range OPERATION Rear Panel Controls BUTTON FUNCTIONS MENU FUNCTIONS repeated pressing the MENU button cycles the control through the following modes Manually select the DMX address using up and down buttons Press ADDRESS ADDR ENTER when selected Select either MASTER DMX or REMOTE u
9. sing up and down buttons Press MODE MODE ENTER when selected In MASTER the unit will control another unit set to DMX PROGRAMME PROG Manually select a range of standalone programmes Press ENTER when selected TIME TIME Select the length of time between colour changes Press ENTER when selected The left hand display shows a rotating line when DMX data is received Standalone Master Mode In this mode the illuminator set to Master can be used in two ways either as a single independent illuminator or in a Master Slave configuration with several illuminators connected together using DMX cables The Slave set to DMX will mimic whatever standalone programme the Master Illuminator is set to All menu functions are available in Master mode Standalone Remote Mode Again in this mode the illuminator set to Remote can be used in two ways either as a single independent illuminator or in a Master Slave configuration with several illuminators connected together using DMX cables The Master color sequences are controlled by a RF remote control and again the Slave will mimic the Master Illuminator Universal Fiber Optics OPERATION DMX Mode In this mode the Illuminator set to DMX can be controlled either by another Cube in Master mode or by a DMX controller Cube Remote Controller Description Details Comments Hanes Measured in free space may be attenuated by 8 obstructions or other RF devices Frequen
10. ze L 4 3 110mm W 4 3 110mm H 3 7 95mm Weight 1 3lb 0 6kg Universal Fiber Optics UNIVERSAL FIBER OPTICS Universal Fiber Optic Lighting LLC 6119A Clark Center Avenue Sarasota FL34238 Tel 941 343 8115 or 800 UFO 5554 www fiberopticlighting com
Download Pdf Manuals
Related Search