User Manual
Contents
1. This section is to config signaling protocol for the SIP Server and Client 4 6 1 SIP 1 configuration User can configure specific parameter of SIP1 on this page FV8010 User Manual account info server 202 96 154 154 user name UTOOOO032 password 147258 Definition of each parameter described as below SIP Unregistered Configuration Register Server address Proxy Server addr Register Server Port Proxy Server Port Register Username Proxy Username Register Password Proxy Password Domain Realm Local SIP Port Phone Number Register Expire Time Detect Interval Time RFC Protocol Edition DTMF Mode User Agent SIP register state 1f register successfully show Registered in the square bracket otherwise show Unregistered Set SIP register server IP address Set proxy server IP address usually SIP will provide the same configuration of proxy server and register server if different such as different IP addresses then each server s configuration should be modified separately Set SIP register server signal port Set SIP proxy server signal port Set SIP register server account username Usually it is the same with the config port number Set the SIP proxy server account username Set password of SIP register server account Set password of SIP register account Enter the sip domain if any otherwise FV8010 will use the proxy server address as sip domain Usually it is same with register2. Select DHCP on below single option IP Phone will auto config the WAN parameter with immediate effect O Static DHCP O PPPOE WAN port PPPoE mode configuration Select PPPOE on below single option Static O DHCP PPPOE Set below parameter of PPPOE mode PPPOR server ANT User pppoetest Password e Server If ISP no special requirements remains default setting User Provided by ADSL ISP Password Provided by ADSL ISP Click Apply button after finished above setting IP Phone will auto config the WAN parameter with immediate effect The setting of WAN is still effective and enables IP Phone to connect to internet 4 5 2 LAN Configuration This web page displays the LAN parameter configuration Please note once the bridging mode is selected the LAN configuration will be no longer effective FV8010 User Manual Bridge Mode IP 122 162 10 1 lNetmask 255 255 265 0 DHCP Service Kc NAT Configuration Example e Config LAN generally config one private IP address TP 192 168 10 1 Netnask 255 255 255 0 IP LAN IP address Netmask Network Mask e Start LAN DHCP Service and NAT or not default setting is start Y DHCP Service EC Start Bridge Mode or not transparent mode Once start Bridge Mode some parts of LAN config will be disabled and the phone will no longer set IP address for LAN physical port LAN and WAN will join in the same network 4 6 VOIP Configuration
3. This page is for NAT configuration such port forward DMZ Network Address Translation NAT provides a mechanism for a privately addressed network to access registered networks such as the Internet without requiring a registered subnet address This eliminates the need for host renumbering and allows the same IP address range to be used in multiple intranets With NAT the inside network continues to use its existing private or obsolete addresses These addresses are converted into legal addresses before packets are forwarded onto the outside network FV8010 User Manual p TPS e ALG m FTP St CG LE PPTP ALG Tnside IF Inside TCP Part Chat si de TCP Port Insi de IF Inside UDOP Port Chat si de UDP Part ran ter Type Il TCP Dut si de Fort ll Insi de Ip Il Inside Port Il cna side IF Inside TP Advance NAT setting Maximum 10 items for TCP and UDP port mapping IPSec ALG Enable Disable IPSec ALG FTP ALG Enable Disable FTP ALG PPTP ALG Enable Disable PPTP ALG Transfer Type Transfer type using port mapping Inside IP LAN device IP for port mapping Inside Port LAN device port for port mapping Outside Port WAN port for port mapping Click Add to add new port mapping item and Delete to delete current port mapping item 4 7 3 NAT service configuration ATTP Port 50 Telnet Port 23 m RIP Initial Port 10000 RIP EK Quantity 200 4 7 3 1 CN Configure
4. SIP1 Example 3 about lifeline Number Call Mode Destination Port Aliaz Suffix el P length D 1 ifeline o 0 0 0 0 no alias no suffix 0 Image of T means when user connect PSTN line to the lifeline port user could make PSTN call by add a before the calling number Delete Number Call Mode Deztination Port Alias Suffix Del length T lifeline D 0 0 0 n no alias na suffix 0 1 lifeline o 0 0 0 0 no alias ino suffix 10 22 lifeline Io 0 0 0 In no alias ino suffix 10 am petete moasey Tr 32 FV8010 User Manual Phone number T Call mode lifeline When user dial there 1s a second dial tone from the pstn line then dial as directly using PSTN line Phone number 1 Call mode lifeline When user dial 1 there 1s a second dial tone from the pstn line then dial as directly using PSTN line Phone number 22 Call mode lifeline When user dial 22 there is a second dial tone from the pstn line then dial as directly using PSTN line Example 4 IP to IP calling Peer to Peer calling mode direct make calls and no need to set phone number thru proxy server user could refer to Dial peer setting on web configuration charter The phone should be operated under following condition satisfy one option e Requirement 1 both two FV8010 are assigned the public IP address individually e Requirement 2 both two FV8010 using private IP address should be on
5. Save and clear sesso iot I tur I uri ci etri bee 32 dU SO cou EUM D MEE MEI M M ME E EE EE 22 ee 32 AAO E A O O A 34 AA Web Update uos das dax teo OR da RE ed eck hed tr Rat an ied ere uu eie 34 2 10 2 EP an TIPP pale assiste ong ecce Ong iub hat On never ten nq impie aq imde 34 2 DE System Tnafidbe om ioo m EE Ro te mtm 37 A NET D To TD 37 4 L1 2 5V ste rte rca 38 5 DEFAULT FACORY SETTING gp 39 6 CONFIGURATION BY PHONE oa a ociosas ana Raiose 39 I TELNETCONPIGURATION 5 5 tiere in 40 TACOS PEOUGGUEG enana les dd e ee dal cesis e dal co lo pe dl el 40 7 2 Telnet basic Introduction Basic structure Basic commande 40 7 3 Global Command a 41 RP A A detent ete 42 TAL LAN Tae e SeLUTIDS oou oua Dun Oud Du ud Dun bd 42 TAD NANA C EE 42 1 5 NES one os ote e Rd edu diu iet aS be Ee 42 EE tee tege eege 43 SO O S aa 43 758 5159 User management Debra Level OT RE 44 TAO SHOW SC running Dad 44 7 11 7 13 Logout tracert trace network path info update oooooonnnnoooooooooooonnnnnnnnnnnononnnonoss 45 7 14 7 19 Upload download configure password reload Network Diagnosis Restore to factory default 46 1 20 S POST MOde Sale THOU c Seo TES o ed 47 1 20 1 ACCESS POST Mode Process intet o en Lie aa ee ea mto 47 7 20 24 POST mode daneses rro lares esos eed 47 7 20 3 POS EMOS TFI P update aaa 48 FV8010 User Manual 1 Welcome FV8010 series of gateways are innovative gateways that offer a rich set of functionality and
6. can get IF settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address Set you PC dynamic mode to get ip address from FV6020 LAN port Sabet mask Default gateway Ge Obtain DNS server address automatically Use the following DNS server addresses Prefered ONS server Alternate DS semen Method 1 General Method 2 You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings alternative C Obtain an IP address automatically Use the following IP address IP address or select your PC static IP address Subnet mask Default gateway 192 168 10 C Obtain ONS server address automatically Use the following DNS server addresses Preferred DNS server AU 9 134 134 202 96 o e Advanced Altemate DNS server e Method2 FV8010 User Manual d Input cmd command on the RUN submenu under PC START key in ipconfig all on the command lines dialog box to find the default gateway IP address which is FV8010 LAN IP address Search 3 ra NN 3 xj 3 Type the name of a program folder document or 17 Internet resource and Windows will op
7. the same LAN If A dial number 187 A can talk with B If B dial number 155 B can talk with A A phone IP address 192 168 0 155 B phone IP address 192 168 0 187 in dail peer config page in dail peer config page 182 166 0 187 132 168 0 155 39 FV8010 User Manual 4 9 Config Manage Save and Clear configuration Notice clear config in admin mode all settings restores to factory default clear config in guest modem all settings except sip advance sip restore to factory default 4 9 1 Save Config Once change is made Users should save the modified configuration to take effect otherwise the IP Phone will go back to the last saved setting after phone reboot The interface of Save Config as below please follow the four steps below to config MEE L neto 1182 ies 1 gt Ge system HBanage Enter Config Manage Menu Save Config Submenu Click Save Button Return to Current State Web page 4 9 2 Clear Config There are four method to clear config set factory default web telnet post mode keypad If the IP Phone doesn t work properly after modifying config users can clear all modified config on Clear Config web page The phone Will clear all modified config and restore the default factory configuration Default network type for WAN is DHCP mode default LAN IP address is 192 168 10 1 Process Please follow the below steps to clear config Enter C
8. this is optional configuration item it is the number to be used when the other party s number has prefix when no configuration has been made shown as no alias add xxx add xxx before number 1n this way it can help user save the calme length all xxx the number is all replaced py xxx speed dialing can be implemented for example user configure the dialing number as 1 with the configuration all the actual calling number will be replaced del delete n bit m the front part of the number n can be decided by the replacing lensth this configuration can decide the protocol for appointed number rep xxx n bit m the front part of the number will be replaced nis decided by the replacing length Suffix optional Configure suffix this is optional configuration item it is the additive dial out number behind the number when no configuration has been made shown as no suffix 30 FV8010 User Manual Example 1 T mean any length digit number Destination is 255 255 255 255 that mean calling out through SIP2 server Destination is 0 0 0 0 Config page 255 255 255 255 all 33334444 d 1 2 add 0755 010T aT el T rep 8610 that mean calling out through SIP1server Explaination That means Any digits number starting with 9 pass throught SIP2 server Here alais is del Delete Length is 1 that means the phone will delete the first number before send number to server It can be used for s
9. 0 User Manual 7 3 Global Command Global command is available under all nodes FV8010 support following commands chinese Set the language of help prompt info to chinese Chinese clear Clear screen clear english Set the language of help prompt info to english English Go back to upper level of node 1 Display help prompt info 1 help ping 2 Display all subnode under current node 2 help and local command command Exit telnet config interface ping One test program using to check network ping www google com or program availability who Display current users login to PC who Common Network command Command Command function Example Name ping www google com tracert www google com show basic show ip route show ip arp show ip netstat Run Netstat program telnet Htelnet 192 168 1 2 restore default except network configuration Set all default Clean all configuration and restore default setdefault all manufacturing setting 42 FV8010 User Manual 7 4 Net configuration 7 4 1 LAN interface settings Path lt config interface fastethernet lan gt disable enable bridge mode disable enable DHCP service Show current DHCP rules dhcpshow Change LAN port IP address ip addr x x x x mask X X x x Example config interfact fastethernet lan lt config interface fastethernet lan gt ip addr 192 168 1 10 mask 255 255 255 0 7 4 2 WAN interface settings path lt config interface fast
10. 8 a ne N PEE 9 2 Amm mm gar az ub vi Le SP an aT 39 FV8010 User Manual 5 Default Factory Setting Oo Gain IP address thru DHCP mode WAN Port static IP is 192 168 1 179 LAN port IP is 192 168 10 1 Default is to start the DHCP service and NAT function Default communication protocol is to use SIP SIP port is 5060 Default HTTP port is 80 Telnet port is 23 Default number end is button Default user account is admin and guest 6 Configuration by phone We have provided some command to config FV8010 by phone We can connect one analog phone to Phone interface We can input following command by Hand free or Handset Input Input Input Input Input Input Input Input Input e s Saala 000 100 101 102 103 104 4111 222 Reboot Device Clear configuration Gateway work at Static mode Gateway work at DHCP mode Gateway work at PPPoE mode Gateway work at Bridge mode Gateway work at Router mode Get the IP address of Gateway by voice message Get the Number of Gateway by voice message 40 FV8010 User Manual 7 Telnet configuration 7 1 Config Procedure e Input command cmd on Run submenu under PC START menu and then key in telnet phone IP address enables users to config IP phone thru telnet e Input username and password both default Username and password of Administrator account are admin e Config IP Phone through command lines Note 1 We suggest users to con
11. Emo Sp Input Output Output zl Deny Permit Deny 2 Src Addr 192 168 0 187 Deg Addr 192 168 0 120 FV8010 User Manual 4 7 5 QOS 802 1p Configuration Ir QOS Enable Ir QOS Table Include e Ne tma sl Bes d Ne tmask Ada QoS Control based on 802 1p for different IP users The QoS is used to mark the network communication priority in the data link MAC sub layer FV8010 will sorted the packets using the QoS and sends it to the destination QoS provides service classes for accessing traffics in Internet QoS Enable Enable QoS service QoS Table Enable include QoS table FV8010 will only provide QoS service to the network address included in the QoS table Disable the option FV8010 provides QoS service to the network address outside the QoS table Delete Enter the IP MASK configure and select delete to delete corresponding item Add User can set the QoS Table using IP and Netmask the IP can be network address set netmask to 255 255 255 255 4 7 6 Advance SIFI state SIPA state Private User Agent common e Enable Private Register e Enable Private Outbound Proxy 20 FV8010 User Manual To show the phone whether has been registered on public server or private server 4 7 6 1 SIP STUN Configuration STUN can support SIP terminal s penetration to NAT in the inner net In this way as long as there is conventional SIP proxy and a STUN server placed in the public net it will do but STUN o
12. FV8010 User Manual User Manual FV8010 Series Gateway Version2 0 FV8010 User Manual CONTENT L VEL COME tanatorio 27 ENS EE ECK HL DE A nase DU He TotD Pacts eet Lett ED actos 4 2 2 Sateby COMMA AIC CS AAA ad ead aad ee 4 3 PRODUCT OVER Y TE W isso said 4 WEB CONFIGURATION ccssccccedsstsccticccccasiessncatacincncauseusacatacoevenodeceacacisessegedane Tea eeu nea e CH Haa ERN A Physical Connections b eH Ee Pe E eae aad 6 2 2 Prteparationdot Web CODO UE Te alles 6 A SE Ee ddnde dns 8 d C uttenb Sl ii 9 4 5 Network configuration o Tae gad nese TO e E n TO e E GR EM t e 9 VAIN eset Soc 9 E ER 11 EON Nee cou nM NE Eu E I2 4 6 1 Public SIP server configuration SIPI occcccccnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnoninonininoss 12 d dU AUN OOO POPE A ta A aM eas l4 ATA DAPR cc 14 A E 15 A NES CV TIE RITA tei IES AAA 16 AA ll c rr 17 EA o EE IN 18 SE 19 d SIP SN 20 4 7 6 2 Public SIP back up server SIP1 backup essa 20 A A Aad die ee 21 d 5 Daeitaltndp E 21 2 T dA Faxed digital Ma Ps ue n Rise RG OO 21 4k T2 User delme Ee eeh APG hist nd Hte 22 41 5 EE 23 O O 24 2 15 5 2 Call E AA uM MP ec eet 24 EE 24 AS 2 2 AA ee ee ere E 25 uT SA EE 25 FV8010 User Manual 4 7 8 2 4 Three way Confetetice ooo aceto oo eee ees aei e 25 Aso DTE ROME anal 26 AETS 2 29 er A EE 26 A Ae 26 SNB um TES 27 A in bb iib tint 28 4 9 Contie manage
13. _ password XXX Set register server info server register ip X x x x _port xxx user xxx password XXX Set alter proxy info alter server proxy ip X X X x port xxx user XXX password xxx Set alter server info alter server register ip X X X x port Xxx user xxx 44 FV8010 User Manual ooo wo Example config sip server lt config sip server gt server proxy ip 210 25 23 22 port 5060 user aaa password 123456 7 8 User management path lt config user gt Function Command Change user right access user XXX access xxx Change user password password user xxx Example Hconfig user lt config user gt enitry user abc access 7 Example lt config user gt access user aaa access 7 Note The command user xxx access digit Here if the digit is less 10 then the user level is guest If the digit is more that 10 then the user level is administrator 7 9 Debug Level 0 7 path lt debug gt disable enable debug dsp module no dsp xxx 7 10 show system running info path lt show gt show network status basic show current call info call active 45 FV8010 User Manual show CODEC capability show debug info capability debugging show LAN status and DHCP server info dhcp server show digital map info dial rule show LAN info show WAN info interface fastethernet lan interface fastethernet wan show arp table info ip arp Show DNS gateway info ip dns Show netstate inf
14. address field now Manage IP Address IER 168 1 178 Netmask 255 255 255 0 Static Gateway IER 168 1 1 DNS Domain Primary DNS 202 96 134 133 Alter DNS 202 96 128 68 pdate ystem fanage Display lt valid MAC gt that means the FV8010 had been certificated Display lt invalid MAC gt that means the phone need a MAC Authenticating Code get it from Favil or your provider Display invalid MAC gt that means the FV8010 can not work normally Three models Static DHCP PPPoE are paratactic Users can set the right model base on actual requirements WAN Port static mode configuration Default network confin ic DHCP model Users need to set below parameters Static DHCP PPPOE EL IF Address A 168 10 T1 Netmask 255 255 0 static Gateway 192 168 1 1 ul XC UNS Domain voip con com Primary DNS 1192 1 1 Alter DNS 192 1 1 1 IP Address WAN IP address Netmask Network mask FV8010 User Manual Gateway Default gateway IP address DNS Domain Option configuration Primary DNS IP address for primary Domain Name Server Alter DNS Option configuration Click Apply button after finished above setting IP Phone will save the setting automatically with immediate effect If users visit FV8010 thru WAN user need to know the FV8010 WAN port ip address on normal phone operation 111 for hear FV8010 saying IP WAN port DHCP mode configuration
15. ate Server Register Configure permit deny private server register Enable Private Outbound Proxy Configure enable disable private outbound proxy if you have no stun server advise to enable the option Note about how to use SIP Please refer to the Dial peer chapter 4 7 7 Digital map configuration 4 7 7 1 Fixed digital map End with 7 Fixed Length 11 Lei Time out 5 3 3032 Appl End With Use as the end of dialing Fixed Length When the length of the dialing match the call will be sent Timeout Specify the timeout of the last dial digit The call will be sent after timeout 22 FV8010 User Manual 4 7 7 2 User define flexible Digital map table Digit map is a set of rules to determine when the user has finished dialing Digital Map is based on some rules to judge when user end their dialing and send the number to the server With digital map users don t have to press key or call key after dialing If the number dialed matches some item in the digital map table or it doesn t match with any item this number will be sent out immediately It is not like using dial peer Using digital map won t change the number dialed the number sent is the same as the number dialed X Represents any one number between 0 and 9 Tn Represents the last digit timeout here n represents the time from 0 9 second it is necessary Tn must be the last two digits in the entry If Tn is
16. configurating the number IP table For example user know the other party s number and IP and want to make direct call to the party by point to point mode the other party s number is 1234 make a configuration of 1234 directly then the phone will send the called number1234 to the corresponding IP address Or set numbers with prefix matching pattern for example user want to make a call to a number in a certain region 010 user can configure the corresponding number IP as 010T protocol IP after that whenever user dial numbers with 010 prefix such as 010 62201234 the call will be made by this rule Bases on this configuration we can also make the phone use different accounts and run speed calling without manual swap When making deletion or modification select the number first and click load then click Modify and complete the operation Display of calling number IP image list Number Destination Port Alias Suffix Del length LE 192 168 0 157 Soen no alias no suffix Io Der 92 168 0 187 5060 ao alias no suffix Jo Eng 255 mE 255 255 ESE Este del Ina suffix 11 ooon Goen all 07T55 mo suffix Jo jo 56060 rep S610 no suffix 3 er es 168 0 187 5060 mo alias lig8d8 Ml Far H92 168 0 187 5060 no alias ses lo o Add Click Add the following figure will be shown at the lower part of the page 010T It is to add outgoing call number t
17. e phone 4 7 8 2 6 Limit list Limit List GS a Outgoing calls with these phone numbers will be refused for example if user don t want the phone to dial a certain number please add the number to this table and the user will be unable to get through this number 4 7 9 MMI Filter MMI Filter Start IF End IF A Eaze O Start IP to be deleted 21 FV8010 User Manual MMI filter is used to make access limit toFV8010 When MMI filter is enable Only IP address within the start IP and end IP can access FV8010 4 7 10 DSP configuration On this page user can set speech coding IO volume control cue tone standard caller ID standard and so on Coding Rule e711Alaw dk Signal standard CHINA sl Input Volume i fo 3 Output Volume p 0 3 6729 Payload Length fio m I VAD Configuration Explanation Coding Rule zT11Ulaw amp dk Configure Coding Rule according to network bandwidth support G 711a u G 729 Signal Standard China Congfigure Signal Standard according to country s phone voice 6728 Pavload Leneth 20n v Normally G729 Payload Length don t need be changed into 10 ms Output Volume 1 9 Handset out volume input Volum 1 5 28 FV8010 User Manual 4 8 Dial peer Number IP table configuration Function of number IP table is one way to implement the phone s calling online and the calling of the phone will be more flexible by
18. ed server and proxy server IP address Set local signal port the default 1s 5060 Set assigned phone number Set expire time of SIP server register default is 120 seconds Set detection interval time of server default is 120 seconds Enable the phone to use protocol edition When the phone need to communicate with phones using SIP1 0 such as CISCO5300 and so on need to modify into RFC2543 the default is to RFC3261 Set DTMF sending mode support RFC2833 DTMF RELAY inband audio and SIP info Set the user agent if have default 1s common 13 FV8010 User Manual Enable Register Configure enable disable register Auto Detct Server Co work with Server Auto Swap and Detect Interval Time Enable this option FV8010 will periodically detect whether the public SIP server is available if the server is unavailable the FV8010 will switch to the back up SIP sever and continue detecting the public sip server FV8010 will switch back to the primary SIP server if the server is available again Enable Pub Outbound Configure to enable to use public outbound proxy if you have no stun Proxy server advise to enable the option Server Auto Swap Configure main and backup auto swap server if the phone enables main and backup server function the automatic detection and auto swap functions should both be chosen After finished the aforesaid network and VoIP configurations on the phone and network communication has been implemented the user can ma
19. ee Remote File PAIS AL den lading please wiring CFT E j j Curent Acton L ns dh vari 2058 bikes 10652754 bytes in EES e lira suncesn E Gg Su Seting Hes TPTP Client Henu A EK AT IE l eet pGagapotpsn Enter yaur meyer ancy PUST ATT 111 TFTF Client Fosn load FV8010 provide safe mode When there is booting problem because of setting problem or firmware problem User can restore the factory setting or upgrade to a new firmware to solve this problem 49
20. en it for you c CA WINNT systems cmd exe icrosoft Windows 2000 Version 5 00 2195 cc gt ARAVA 1985 2000 Microsoft Corp Documents and Settings Administrator lipconfig all findows 2660 IF Configuration Host Mame SEI Primary DHS Suffix wa de Hode Type a2 2 2 Broadcast IF Routing Enabled Hn WINS Proxy Enabled Mo Ethernet adapter AS EH Se e n Connection specific DNS Suffix T Description a a 2 Realtek BF REEL P REL Family Fast E 2ernet NIC Physical A HH HC 76 F4 55 DEB DHCP Enabled MED oR ER Tee ee ec Autoconfiguration Enabled IP Address E 192 168 10 2 SU ee Mask ee ere ees ee Se LA Default Gateway a a2 uL 16 1 FYDDI LAN TP DHEE GEFUR EG A m 14 1 DHS Servers 172 14 1 4 3 User verification Users are requested to make verification when config or browse the IP phone thru web pages users can direct login the config menu by inputting username and password as below Default username and password is Administrator Username admin password admin low level user interface User Username guest Username guest high level user interface FV8010 User Manual 4 4 Current State On this page user can gather information of each commonly used parameter of the phone it is shown as the following figure e Network section Displa
21. ent unauthorized private network devices to access the internet FV8010 User Manual Access list support two type limits input access limit or output access limit Each type supports 10 items maximum FV8010 firewall filter is base WAN port So the source address or input destination address should be WAN port IP address Configuration in access enable Enable in access rule out access enable Enable out access rule Input Output Specify current adding rule is input rule or output rule Deny Permit Specify current adding rule is deny rule or permit rule Protocol Type protocol using in this rule TCP IP ICMP UDP Port Range port range if this rule orc Addr Source address Can be single IP address or network address Dest Addr Destination address can be IP address or network address Src Mask Source address mask Indicate the source is dedicate IP if set to 255 255 255 255 Otherwise is network ID Des Mask Destination address mask Indicate the source is dedicate IP if set to 255 255 255 255 Otherwise is network ID Example Intention Computer A cannot ping computer B Computer A connect with FV8010 LAN port Computer A IP address is 192 168 10 2 FV8010 WAN port IP address is 192 168 0 187 FV8010 LAN port IP address is 192 168 10 1 Computer B IP address is 192 168 0 200 FV8010 firewall config eet Protocol E re Addr E rc Mask D es Addr D es Mask D deny Tore 192 l s 0 Le 255 Sim guum 255 192 les Q 120 255 Zim
22. er amp Enable Pub Outbound Proxy Usually these two option need to be selected when you want to use SIP1 4 7 Advance 4 7 1 DHCP server configuration When FV8010 work as a router This config is for network device which connect to FV8010 LAN port DNS Relay DNS relay acts as a forwarder between the DNS Clients and the DNS Servers DNS relay is designed for home office networks where the users might want to dial into more than one Internet Service Provide ISP FV8010 User Manual m DNS Relay Name St art T End TE Lease Time Netmask Gateway DNS lani 192 Ti 192 168 10 50 11440 255 Elles mv du 192 168 10 1 192 168 10 1 Lease Table Name NENNEN Lease Time ti minute Start IP COo End IP Netmask Gat eway I o tC LL REB See DHCP server manage page User may trace and modify DHCP server information in this page DNS Relay enable DNS relay function User may use below setting to add a new lease table Lease Table Name Lease table name Lease Time DHCP server lease time Start IP Start IP of lease table End IP End IP of lease table Network device connecting to the FV8010 LAN port can dynamic obtain the IP in the range between start IP and end IP Netmask Netmask of lease table Gateway Default gateway of lease table DNS Default DNS server of lease table Notice This setting won t take effect unless you save the config and reboot the device 4 7 2 NAT Configuration
23. er dialing dial then dial the third party number C user directly the phone will transfer the calls to C The result is C phone will ring A will hang up User C pick up phone then user B willtalkwithC Operating process lt FLASH gt button e third party number Example A are talking with B A click FLASH button holding B line then dial user C number 4 7 8 2 4 Three way conference call Enable Three Way Call Configure enable disable three way call When user A are talking with user B as the call origination user A click FLASH button onthe normal phone to hold user B line and then dial the third party user C after A talk with C User A click lt FLASH gt button again to recover the talk with user B At this 26 FV8010 User Manual time user A press key to make C into the three way conference Operating process FLASH button F third party number FLASH button Example A are talking with B A click FLASH button holding B line then dial C number A will talk with C A click FLASH button again holding C line and Adial d A B Cmake the three party conference sucessfully now 4 7 8 2 5 Black List Black List o ceo Incoming call in these phone numbers will be refused It is for precluding incoming communication like Call ID If user don t want to answer a certain phone number please add this phone number to the list and then this number will be unable to get through th
24. ethernet wan gt disable enable dhcp client no dhcp disable enable pppoe no pppoe disablelenable QOS no qos oet default gateway IP gateway X X X X oet WAN port IP address ip addr x x x x mask X X X X Example H config interface fastethernet wan lt config interface fastethernet wan gt F ip addr 202 112 241 100 mask 255 255 255 0 You need to reconnect if the WAN port has been changed 7 5 Netservice path lt config netservice gt Set telnet access port telnet port xxx Show telnet access port telnet port Set RTP initial port and media port startport xxx number xxxx quantity 43 FV8010 User Manual Add route rule route gateway X X x x addr x x x x Mask x x X x Delete route rule no route gateway x x x x addr x x x x Mask X X X x Example config netservice lt config netservice gt dns ip 202 112 10 36 domain voip com lt config netservice gt media port startport 10000 number 200 lt config netservice gt route gateway 202 112 10 1 addr 202 112 210 1 mask 255 255 255 0 7 6 Port settings path lt config port gt Show port settings show 7 7 SIP settings path lt config sip gt disablejenable auto detect no detect server server Set sip domain default domain xxx Set DTMF mode dtmf mode xxx disableJenable auto swap no Swap server server Set local SIP signal port signalport xxx Set proxy server server proxy ip X X X X port xxx user xxx
25. fig IP Phone thru web browser instead of keypad or telnet 2 After any change of configuration please remember to make write command to save changes and then input reload command to reboot IP phone to take effect 7 2 Telnet basic Introduction 7 2 1 Basic structure User may use telnet command to access and manage gateway FV8010 adopts tree structure for telnet Every node contains its sub nodes or local command User can type help or whenever to see sub nodes and all local command under current node Besides local command there are some global commands can be used in each node 1 2 2 Basic command Logout exit telnet mode Write save current settings Type sub nodes name in current node to switch to sub node Type or exit in current node to return to parent node Type help or can see all sub nodes and all local command under current node every help item has comments such as command or node to distinguish sub nodes and local command Type help or in command can see all parameters using in this command When typing node name or command user no need to key the full name use TAB button will make it more efficient There are two types in command parameters optional and required required parameter use as prefix and optional use _ as prefix User GG 33 may type or then press TAB button for complementarily 41 FV801
26. here are two kinds of outgoing call number setup One is exactitude matching after this configuration has been done when the number is totally the same with the user s calling 29 FV8010 User Manual number the phone will make the call with this number s IP address image or configuration Another is prefix matching be equivalent to PSTN s district number prefix function if the previous N bits of this number are the same with that of the user s calling number the prefix number length then the phone will use this number s IP address image or configuration to make the call When configurating the prefix matching letter T should be added behind the prefix number to be distinguished from the exactitude matching Call Mode sip we Configure the calling line route SIP and lifeline 182 168 10 11 Configure destination address if it is point to point call then input the opposite terminal s IP address it can also be set as domain name and resolved the specific IP address by DNS server of the phone If no configuration has been made then the IP will be considered as 0 0 0 0 This is an optional configuration item Port optional 00000000 Configure the other party s protocol signal port this is optional configuration item when nothing is input then the default of h323 protocol is 1720 the default of sip protocol is 5060 lifeline required no configuration of this item shown as O Alias optionl 0 Configure alias
27. ke VoIP calls by the calling register and proxy server Note Some ISP internet may inhibit the phone to register and cancel the register in process so user had better cancel apply or register soon and then submit registration repeatedly Server may stop response of dialogue machine then the phone receives no register cancel login request and registration state will show incorrectness Configuration Example Firstly users should get the account info from VOIP Service Provider Including Server IP address port username password etc and follow below procedure e Config registered server and proxy server IP address and signaling port Support DNS for registered server and proxy server Register Server Addr 10 1 1 138 Proxy server Addr 192 1 1 138 Register Server Port 5060 Proxy Server Port 5060 e Config the username and password for registered server and proxy server Register Username client Proxy Username client Register Password Proxy Password e Config the phone number Usually phone number is same with SIP account 14 FV8010 User Manual Remark due to the above register username is client so the phone number is different from SIP account Phone Number 62281493 e Config the domain realm Usually it is same with registered server and proxy server IP address Let it be blank Domain Realm 10 1 1 138 e Select below two option and registered in local outbound public proxy Enable Regist
28. le name FYA0 200308 2 Type Application update Porotocol Current State WT OM etrork a P Tias TERRE eo ure kppli Connect Mode DHCP siria Er WAN GE r IP Address 1932 168 0 155 AN IF Address 192 166 10 1 ve FARS C onfig Manage STI T date stem EETA Firmware version After it update successfully You will find the new After you click apply you can find the file that it version in Current State had download to your pc lt c temp gt 37 FV8010 User Manual 4 11 System Manage 4 11 1 Account Manage maximum 5 account Users can edit users add or delete account and modify existing users authority on this web page User Name User Level admin Ro ot guest e eneral aa Delete moaiey ese zi Definition of each parameter described as below User Name List existing phone user account name User Level Show existing user account level two option Root and General Root level users have the right to modify config General level users have the right to read only Add Add user account to IP phone Delete Delete increased user account Modify Modify increased user level and password Operation Example e Add one new account Click Add button input User name No Modify Choosing User level from dropdown menu set new user password confirm password submit the new account info by clicking submit button show submit success on screen return to account configu
29. nfiguration The IP Gateway Web Configuration Menu can be accessed by the following URL http Gateway IP Address The default LAN IP address is 192 168 10 1 and WAN IP address is 192 168 1 179 If the web login port of the gateway is configured as non 80 standard port then user need to input http xxx xxx xxx xxx xxxx otherwise the web will show that no server has been found If connect PC with FV8010 LAN port and config to obtain IP address automatically you could check the default gateway IP which is LAN IP address The procedure as below FV8010 User Manual a Access to Property of local area connection dialog box Ad x General Authentication Advanced Connect using Hg Broadcom MetXtreme Gigabit Etheme This connection uses the following items QoS Packet Scheduler 1 AEGIS Protocol IEEE 802 1x v2 2 1 0 47 Intemet Protocol TCP IP Description Allows your computer to access resources on a Microsoft network 4 k EE 2 Show icon in notification area when connected v Notify me when this connection has limited or no connectivity b Select Internet Protocol TCP IP click Property button c Setting refers to below dialog box and then click OK button PC will obtain IP address automatically or set your pc static ip 192 168 10 2 Internet Protocol TCP IP Properties E xl Internet Protocol TCP IP Properties General Altemate Configuration Method 1 You
30. nly supports three NAT modes FULL CONE restricted port restricted SLUM Server Addr 0 0 0 0 IF you have stun server please input stun server address here STUH Server Port 3478 The STUN server default port is 3478 STUN Effect Time minute The unit is minute if you have STUN server please input interval time for STUN S detection on NAT type Enable SIP Stun Configure enable disable SIP STUN if you have stun server please enabe the option 4 7 6 2 Public backup server configuration Eulate cedo qn ene Reiter 101 111 Public Alter Proxy 0 D D 0 Register Port 5060 Proxy Port 5060 Register Username 1234 Proxy Username 1234 Register Password e Proxy Password the specific configuration parameter has the same meaning with public server lt should be noted that the username and password should be the same with the public main server 21 FV8010 User Manual 4 7 6 3 Private server SIP2 configuration Register Password Proxy Password nn Private Register 207 145 183 115 Private Proxy o i yi Proxy Fort IT Proxy Username i Proxy Password Expire Time 60 seconds STUN Effect Time hm Enable SIPStun 0000000000000 Enable Private Outbound Proxy Specific configuration parameter has the same meaning with public server Register Port Register Username Register Password Private Domain Private Mumber Private User Agent Enable Private Register Enable Priv
31. not included in the entry we use TO as default it means system will sent the number immediately if the number matches the entry Dot represents any number and no length limit Number location value range It can be a number range such as 1 4 or number is separated by comma such as 1 3 5 or use a list such as 234 Example 1 8 xxx Any 4 digits number between 1000 and 8999 sending out immediately 9xxxxxxx any 8 digits number starting with 9 sending out immediately 911 after finishing dialing 911 it will send out immediately 99T4 after finishing dial 911 it will send out in 4 second 9911x T4 any more than 5 digits length starting with 9911 sending out in A second Rules A 0000000000000 EST 911 oan AT 000000000000 0000 Add 1 8 xxx Del Using digital map can be combined with dial peer First digital map will determine when the user finished dialing then convert this number to the number actually sent according to dial peer table 23 FV8010 User Manual Number Destination Port Alias Suffix Pel length 2887 192 168 0 155 5060 no alias no suffix 98765432 192 Tis T 55 5060 no alias Ino suffix 5 1911 192 168 0 155 5060 mno alias Ino suffix s S89 892 168 0 155 5060 no alias ao suffix D0 9911234 192 168 0 155 5060 mo alias mo suffix s When user dial 2887 or 98765432 911 99 9911234 they will send out immediately digital map with dial pee
32. o ip netstat Show route info ip route Show icmp packets Stat ip icmp Show igmp packets Stat ip igmp Show ip packets Stat ip ip Show RTP packets Stat ip rtp Show TCP packets Stat Show UDP packets Stat show gateway memory ip tcp ip udp memory gt DI er show NAT information show caller ID info port callerlD show dsp info port dsp show hotline info port hotline show black list info port in limit show outgoing limit info port out limit show current phone number port number show current port status show PPPOE info show QoS table info port status pppoe show sip info EL O MEe O o IN ON show UDP tunnel info udptunnel show running time uptime show gateway version version 7 11 Logout Usage telnet target port Login xxx Password xxx E logout 7 12 tracert trace network path info usage tracert host Example tracert www google com 7 13 update usage FV8010 User Manual update ftp user xxx password xxx ip x x x x file xxx update tftp ip x x x x file xxx Example H update ftp user abc password 123 ip 202 112 20 15 file FV8010 z 7 14 upload configure file usage upload ftp user xxx password xxx Ip x x x x file xxx upload tftp ip x x x x file xxx 7 15 download configure to flash usage download tftp ip x x x x file xxx download ftp user xxx password xxx ip x x x x file xxx Example download ftp user abc pass
33. onfig Manage Menu Clear Config Click Clear Button show Submit Success info on screen Click Return button 34 FV8010 User Manual 4 10 Firmware Upgrade 4 10 1 Web Update On this page user can select the upgrade document firmware or config file from hard disk of the computer directly to run the system upgrade After upgrade completed reset the phone and it will be usable immediately Firmware format is dlf as suffix urrent State etwork o 1al peer ontis Manage date WEB Update TP Update ystem WE EET STEP Enter Update menu WEB Update submenu click browse button download upgrade document from hard disk firmware or config file provided by manufacturer click Update button reboot IP phone to go into effect Note Under system upgrade progress FV8010 may not be restarted normally due to some system reason e g electricity shut off users can re download under post mode 4 10 2 FTP and TFTP Update Users can download upgrade documents or lead in configuration files thru FTP or TFTP mode Please make sure export and import rights are authorized by FTP or TFTP server before using FTP update way 35 FV8010 User Manual Server noo Usernane i st Password po Z rame nooo CES Bucks TRIA file eme Config file import Definition of each parameter described as below Server Set IP address for upload or download FTP TFTP server U
34. peed calling The number user dialed will be replaced fully by the number that is behind all Here alias is all not all It can be used to add local area or prefix before sending out It saves user dialing number Here alias is add not add user want to dial PSTN 010 6228 by SIP1 while actually the called number should be 86106228 then we can configure called number as 010T then rep 8610 and then set the replacing length as 3 So that when user make a call with 010 prefix the number will be replaced as 8610 plus the number and then sent out Relace the number that user dialed before sending to SIP1 server Here alias is rep not rep this is optional configuration item it is to add number behind the number user had dialed when no configuration has been made shown as no suffix Example User dial 93333 SIP2 server receive 3333 User dial 2 Sipl server receive 33334444 User dial 8309 SIP1 server receive07558309 User dial 010 6228 SIP1 server receive8610 6228 User dial 147 Sip1 server receive 147 0011 31 FV8010 User Manual Example 2 Number Destination emt Alias Suffix Del length ZOT A 5060 no alias no suffix 200T EA EE oe ails 5060 no alias no suffix o When user dial 200 It will pass through SIP2 When user dial 2009 It will pass through SIP2 When user dial 20096 It will pass through SIP2 When user dial 201 It will pass through SIP1 When user dial 20 It will pass through
35. r 4 7 8 Call Service Configuration Value added service configuration On this page user can set value added services such as hot line call forwarding call transfer CT call waiting service three way call blacklist out limit list and so on Hotline D JOD E Forward re Off Busy Mo Answer Always Farward Number IF Fort 5060 E No Disturb E Ban Outgoing nable Call Tranefer Enable Call Waiting led Three Way Call Accept Any Call fio No nswer Time seconde Black Liszt S a Limit List nn 24 FV8010 User Manual 4 7 8 1 Hotline Hotline Configure hot line number of the port With this number of the port this hot line number will be dialed automatically as soon as off hook and user can s dial any other number If you do not use hotline please let it be blank Configuration example 1 Hotline fs notline number Lall Ce Off Busy No Answer Always P Forward Parweard Number IP Port 5060 Hum ber lar 4 7 8 2 Call feature 4 7 8 2 1 Call forwarding Destination Port Alias Suffix Del lensth 192 16 OQ 157 5060 no alias no suffix o Call Forward 9 Off O Busy O Always Call forward default is Disabling when orf is selected if the number dialed is engaged after the phone has received a call then it will automatically transfer to the configured number according to the following picture CF001 configuration when No Answer jg
36. ration interface by clicking Return button aavia RE Root feeneral ba o e Delete increased account Choosing the account need to del from dropdown menu Delete account by pressing Delete button show Submit Success on screen 38 FV8010 User Manual Were modifs e Modify increased account For Root level user account only Choosing the modified account enter below interface modify user level or password click Submit button to submit the modification Owing to the phone s default account accounts of the administrator level admin account and the ordinary level guest account are all weak account and weak password the username and password will be easily to guess on public network so the user had better modify the administrator and ordinary user Enter with manager level when making modification create a administrator account and a browse account you d better not set the name as admin administrator guest etc set password and then save configuration entering with new manager account delete default manager and browse account and save configuration security will be enhanced 4 11 2 System Reboot Once any change of phone configuration is made users need to reset IP phone to go into effect Users should save the modified configuration before system reboot otherwise the phone system configuration will go back to last eave setting The system reboot interface as below CN TA
37. selected if the phone do not receive the incoming call it will automatically in Eh ke Tine teen to the configured number according to the following picture CF001 forward configuration when Always is selected then the phone will directly transfer all incoming call to the number that had configured in advance like the picture showing Faraway Protocol SIP pc unn Port 9060 Pieture CFOO1 Note 1 Number can be sip server extension number or DID number any PSTN number 2 the function has no relationship with the option Pweble Call Transfer that enable or disable No Disturb If it is enabled the phone will not ring when there is a incoming call DND do not disturb enable this option to refuse any calls 25 FV8010 User Manual Ban Outgoing Enable this to forbid outgoing calls 10 No Answer Time seconds The unit is second no answer call forward time setting 4 7 8 2 2 Call Waiting configuration I Enable Call Waiting Configure enable disable call waiting service After it is enabled user hold calls of the other party by lt FLASH gt button by pressing lt FLASH gt button again the call can go back to the previous call If you want to use three way conference this option must be enabled 4 7 8 2 3 Call transfer configuration Enable Call Transfer It is for enabling or disabling f it is enabled when user A are talking with user B A press FLASH button on the normal phone Aft
38. sername Set username of the upload or download FTP server If user select TFTP mode no need to input username and password Password Set upload or download of FTP server password File name Set file name for system upgrade documents or system configuration files system file take Z as suffix configuration files take cfg as suffix Type Config export import upgrade file type three options Application update is system documents upgrade Config file export is export configuration files to server Config file import is import configuration files to gateway Protocol Set transport protocol type two options FTP and TFTP STEP Enter Update menu FTP Update submenu Config FTP TFTP server gt Config username and password of FTP server if select TFTP mode please skip this step key in file name choosing file type from the dropdown menu choosing protocol type Example export config file 1 FTP 1 Copy Wftpd32 software and FV8010 Firmware into a new Folder example c tmp 2 Run wftd32 exe Set a user name and password for FV8010 ftp 36 FV8010 User Manual updating EATEN A Pg Det File Edit View Logging Messages Security Help Help e gt User Rights Security Dialoe 3 x UserName EMO RH voe H D Done User x 5 AAA lx New User 4 New User 5 m User Name Server 192 168 0 48 Server 192 168 0 49 Usernane Ds ername E Fi
39. superb sound quality They are fully compatible with SIP industry standard and can interoperate with many other SIP compliant devices and software on the market 2 Installation 2 1 Package List The FV8010 gateway package contains 1 One FV8010 gateway 2 One universal power adapter 3 One Straight Ethernet cable 2 2 Safety Compliances The gateway should only be operated with the universal power adapter provided with the package Damages to the gateway caused by using other unsupported power adapters would not be covered by the manufacturer s warranty FV8010 User Manual 3 Product Overview FV8010 IP Gateway is a next generation IP network facility based on industry open standard SIP Session Initiation Protocol Built on innovative technology FV8010 IP Gateway features market leading superb sound quality and rich functionalities Power Output Power 12VDC 500mA Line RJ11 port Lifeline Connect to PSTN line Phone RJ11 port FXS Connect to normal phone or PABX WAN RJ45 port for Internet LAN RJ45 port for PC Power Power indicator REG Server indicator Registered ON Registering Blinking Do not register OFF Phone Indicate the calling status Hook on OFF Hook off and in VolP state ON Hook off and in PSTN state OFF FV8010 User Manual 4 0 Web configuration 4 1 Physical connection 1392 165 10 1 POWER LINE PHONE LA PC 132 1685 10 4 2 Preparation for Web co
40. web browse port the default is 80 port if you want to enhance system safety you d better change it into non 80 standard port Example The ip address is 192 168 1 70 you change the port value to 8090 the accessing address is http 192 168 1 70 8090 But if the value is 0 that imply it can t be configured by web browser 4 7 3 2 Telnet Port Configure telnet port the default is 23 port You can change the value to others Example The ip address is 192 168 1 70 you change the port value to 8023 the accessing address is telnet 192 168 1 70 8023 FV8010 User Manual 4 7 3 3 RIP Initial Port Enable RTP initial port configuration It is dynamic allocation 4 7 3 4 RIP Port Quantity 20 Configure the maximum quantity of RTP port The default is 200 Leased IP Address Client hardware Address Leased IPMAC correspondence table of DHCP The table will display all device getting ip address from FV8010 LAN port by DHCP The configuration on this page needs to be saved after modified and will go into effect after restarting If the Telnet HTTP port will be modified the port is SS A IP better to be set as greater than 1024 because the 1024 port system will save DAL Weg X Set the HTTP port as 0 then the http service will be disabled 4 7 4 Firewall Firewall setting page User may set up firewall to prevent unauthorized Internet users from accessing private networks connected to the Internet input rule or prev
41. word 123 ip 202 112 20 15 file FV8010 cfg 7 16 password usage password Enter new password xxx Confirm new password xxx 7 17 reload usage reload Reboot system 7 18 Network Diagnosis There are some telnet commands for checking your network Now Listing below for your information 7 19 Restore to factory default setdefault clear gateway settings expect network part setdefault all clear all settings 47 FV8010 User Manual 1 PC connect to FV8010 LAN port 2 Set your PC IP to be 192 168 10 205 3 Power off 4 after power on within 4 seconds _ telnet 192 168 10 1 5 config page is like below if no page like the below do step 4 again Telnet 192 VolP System Boot POST Wersion A G NW ECT Creation DAA Mar Inn ER KEEN POST Menu TFTP Client Download Print Hoot Params Clear Config Exit Please enter your number Input 3 and enter for clear configuration TFIP Client Download Print Hoot Params Clear Config Exit Please enter your number 3 set default config please waiting clear clear config Finishedt clear sys config Finishedt set default config finished Please Turn OFF Power After 3 seconds please Turn On Sustem HALT How TFIP Client Download Print Boot Params Clear Config Exit Please enter your number 48 FV8010 User Manual 7 20 3 post mode TF TP update firmware Input 1 for TFTP update firmware Process 1 Run TFTP server 2 Cop
42. y firmware into your TFTP server 3 After access post mode input 1 for selecting TFTP updating 4 Input TFTP server address 5 Input firmware name and then enter 6 Input d for starting download 7 If updating successfully It will display MESAS 8 Input x for logout TFTP client 9 Input 4 for logout POST mode BRESSLER FOET Feat Ca ms SES lose Hu oem fi TT Ss n Eila ua Lag PFE ra Ga ERE rera rr E E mmur Muse 1 IE m SES AA J i En E Dori ALE LP liar mwn linad Setting mota LF and 320 Rara Gem FIRR 0 221 i maz EE Tripan uF Tk I el Enter TFTP server Fi 192 168 18 205 E i BEL i IL T HT E 97 TECH EE Fula A YE E Curran Dictas pc EEN mt aE Ta REC TETTE UIT Seren rata 1132 162 10 205 Tip Serves Tito Cien DHCP server Smilog server Ack block 1171 ignored ecerred oca 11 00 00 55 20 960 A Ac block 1233 ignosed peoered ince 18 08 E bo 30 758 a EF AAA isi 504 ET TE ISS EL PARADE X 1 amit Li bask 8427 unc bct d paca 15 06 06 55 32 901 TALSr yor opt ise pack block 1522 a ecared Decs 15 00 00 50 34 7504 Ank block 1533 ignored becerred lane TRU 06 55 35 54E TFIF Client Dew les Ark bak 1511 ignesed paced race 18 706 0055 38 10 in HR L ck block 1933 igoored becerad Disce 15 700 DO 55 40 1419 Ack block 2067 ignased ecerred hace 88 OR 55 47 SER ette onera abt sent 2066 bkr 16067754 beris in 31 s 17 bis ias Sera IF S Bye
43. y the current WAN LAN configurations of the phone e VolP section Display the current default signaling protocol in use and server parameter in use of each protocol e Phone Number section Display the phone number against each protocol WAN Connect Mode DHCP MAC Address 00 01 0e e9 21 00 IP Address 192 168 0 100 Gateway 192 168 0 1 LAN IP Address 192 168 10 1 DHCP Server ON Register Server 203 208 198 51 Proxy Server 203 208 198 51 Register ON State Registered Public Dutboud ON SIP stun OFF Public ol 6665 Private SIP Version e The version number and date of issue have been shown at the end of this page 4 5 Network configuration Network configuration includes WAN Config and LAN Config 4 5 1 WAN Configuration This web page displays the WAN parameter configuration User can view the current network IP linking mode of the system on this page User will be authorized to set the network IP Gateway and DNS if the system adopts the static linking mode If the system selects DHCP service in the network which is using DHCP service IP address will be gained dynamically FV8010 User Manual If the system selects PPPOE service in the network which is using the PPPOE service then the IP address will be gained by the set PPPOE ISP internet and password of the account Note if IP address has been modified the web page will no longer respond owing to the modification so new IP address should be input in the
Download Pdf Manuals
Related Search