Quick Reference Guide VT55 & OBDII
Contents
1. VEHICLE SELECTION menu and confirm selection with the key Step 2 Select the vehicle brand on the screen by using the Al or VI keys and confirm selection with the key Step 3 Hold the tool within a few inches from the TPM sensor Some sensor may require the tool position directly on the rubber tire over the valve stem Some sensors are banded to the wheel and can be located 180 opposite the valve stem Refer to owners manual Step 4 Press the A key The tool will begin to send LF trigger and the TX light will flash Depending on the sensor the tool will activate the sensor on the first or last step Each step identifies the number of valve types used on the vehicle brand Step 5 The tool will vibrate beep after receiving the sensor information The tool will display the sensor ID pressure and sensor state of the valve that is triggered If the tool does not receive the correct information the fail LED will illuminate and you can restart the trigger sequence by pressing the key again Step 6 Follow the same procedure for the rest of the three or four wheels by pressing the key and then Refer to vehicle owners manual or other reference suides for TPM reset procedure B 2 RESULTS DESCRIPTION The picture below is an example of a valve data communication result Valve BORER Oo Ge Ro e identifier pepee ARP2. I don t know where this program ts from or what it s for gt Allow I trust this program because I ve used it before or I know where it s from Details 10 7 The following window will appear click Next gt to continue and follow the onscreen instructions to complete Welcome to the serial emulation port driver Installer M This wizard will walk you through updating the drivers Connect your device to USE port now WWW ateq com To continue click Next Next gt Cancel 8 Click Install driver software anyway if this appears Windows Security x Windows can t verify the publisher of this driver software Don t install this driver software You should check your manufacturer s website for updated driver software for your device Install this driver software anyway Only install driver software obtained from your manufacturer s website or disc Unsigned software from other sources may harm your computer or steal information iv See details 11 9 When the drivers are successfully installed the following window will appear Click Finish Serial emulation port Installer for VISTA Ver1 00 _ Congratulations You are finished _ installing driver The drivers were successfully installed on this computer qe E l You can now connect your device to this computer F your device came with instructions please read them fi
3. 0 Koppernick Road Canton MI 48187 www tpms tool com
4. ATEQ Quick Reference Guide VT55 amp OBDII Customer Service 1 888 621 TPMS 1 888 621 8767 Version MJC 1108 US1 Section A General Description Section B Triggering a Sensor Results Description Section C Using OBDII Function Update Procedure Section D Installing USB Drivers Section E Installing WEB VT Section F Updating VT55 Printing Results General Description of THE ATEQ VT55 The principle of this instrument is to awaken and then retrieve data from smart valves mounted on vehicle wheels in order to check their identifiers The instrument interacts with the smart valves to assist technicians service Tire Pressure Monitor Systems TPMS VT55 may be equipped with OBDII programmer to reset TPMS for import vehicles Front face LCD display Connectors 24 V DC a USB Port Power S Web VT Supply connection RJ45 Port OBDII Connection Power Supply connector Power supply connection to the tool for charging the internal battery 24 V DC Supplied with the tool USB connector The USB connection allows software updates to be installed onto the tool using the WEB VT program TPM sensor results can also be printed using this program RS232 connector The RJ45 connector allows software updates to be installed into the tool and for use of the OBDII programmer SECTION B TRIGGERING SENSOR S B 1 TESTING A TPM SENSOR Step 1 Select the
5. T Tire internal aU E a ra rea E T J pressure aba i far Lad oc When P BAT OK 315 MHE blinking on Pih od REO OT instrument Valve battery hid i PAR I Me EE ee tte is ready to status test again Note The VT55 will identify the sensor information that is transmitted Not all sensors transmit every piece of information shown Vehicle brand Section C USING OBDII FUNCTION Following step 6 in section B Connect the OBDII module with the Ateq VT55 using the RJ45 ports Locate the vehicle OBDII connecter under the dashboard Plug the Ateq OBDII programmer to this port Turn the vehicle ignition key to the ON position Engine Off The VT55 displays the following message once you have collected all sensor information Press the key to re write the valve information into the ECU The VT55 will connect to the ECU and transmit valve information The message SUCCESSFUL TRANSFER appears when the new valve information has correctly transferred into the ECU Disconnect the OBDII connector from the vehicle The OBDII module will be updated when connected with the VI55 The screen to the right will appear if there are any new updates Please follow instruction in SECTION F to update the VT55 Section D Installing USB Drivers 1 Please insert the CD that was provided with the VT55 2 Connect the USB wire to the USB connector of your PC and VT55 Then turn on the instrument 3 The
6. following window will appear Click the Cancel button in the bottom right corner of the screen ca Found New Hardware Windows needs to install driver software for your Unknown Device Locate and install driver software recommended Windows will guide you through the process of installing driwer software for your device Ask me again later Windows will ask again the next time you plug in your device or log on Don t show this message again for this device Your device will not function until you install driver software Cancel 4 In the CD drive open the file AteqUsbDriver for VT55 L as AtegUsbDriwer for V T53 f B a i 5 The following screen will appear Depending on your operating system open the file for XP or VISTA 2 USB VIRTUAL 23 VISTA USB _VIRTUAL_252_4P PEE abe Spey FERAE EE pee STO ae l Auto extracteur de fichier C E eee a y gf eee ee AD all ae he Ps Microsoft Corporation Microsoft Corporation 6 Using VISTA file as an example the following window may appear Select Allow User Account Control g An unidentified program wants access to your computer User Account Control stops unauthorized changes to your computer The source and purpose of this program are unknown Don t run the program unless you have used it before or know where it s from DOSFins exe Unidentified Publisher Cancel
7. rst Status ATEQ T ee A a www ateq com w ATEG 5 A usbser Ports Ready to use Note Please refer to the user manual on CD for detailed instruction when using Windows XP There are additional instructions if you are trying to use the RJ45 port with RS232 connection 12 Section E Installing WEB VT Software 1 Insert the CD supplied with instrument into the PC drive and click on the WebVT icon to start the program WebVT_V1I35_V3 1 PALEY Welcome to the InstallShield Wizard for Web T The InstallShield Wizard wall install Web T on your computer To continue click Mert Cancel 3 The following window will appear please select the location you would like to save the program Click Next gt InstallShield Wizard Choose Destination Location Select folder where Setup wall install files Setup will install weby T in the following folder To install to this folder check Mest To install to a ditterent folder click Browse and select another tolder Destination Folder C Program Files 4 TE Ow ebs T Browse Back Hest gt Cancel 4 Click Yes when this window appears Question 5 j Do you want to automatically start WebVT Application when you start ae YOU system 5 Click Finish when the WebVT installation is complete 14 Section F Updating VT55 Printing Results 1 Connect the USB cable from the VT55
8. to the PC Click on the WEB VT Icon to start the program El WEB VTSO 2 The following screen appears You may Update Device or print Valve ID s from here as well ATG Internet service Device Serial Number 5285 01152 Software version CH1 06 Subscription valid until Modify Subsenphons Configuration Automatic Mode COM Events Report Device Detected 15 3 Press Yes to update to the latest software version Update will take several minutes to complete and the status bar will indicate the percentage of update completed A ATEQ TSO 1 1 ioj x Do not disconnect VT50 T50 Serial Number neceedtee Software version 01 01 Subscription valid until Ue November 2007 Modity Subscriptions WAAL ateg com Connection Established Your subscription i valid until 02 Movember 200 A new version is available for download Updating VTS Web 4 When the update is complete disconnect the VT55 USB cable and close the program Note You must have an internet connection to update the VT55 with WebVT software 16 Other Products TRP Test Box Pre Test TPM sensors before you mount them to the tire Ensure your gauge pressure matches the Tire Relative Pressure Save valuable time CDP40 Pressure Calibrator Calibrate pressure gauge Verify TPM pressure reading with pressure gauge ATEQ Corporation 4200
Download Pdf Manuals
Related Search