DEC/HDC/UC/UHDC
Contents
1. Operation Interrupting Operation Open oven door or press STOP RESET pad to interrupt operation Display continues to show countdown time Close door and press START pad to resume oven operation Canceling Mistakes If oven is not cooking press STOP RESET pad to clear display If oven is cooking press STOP RESET pad once to stop oven then again to clear display If oven door is open and time shows in display close oven door and press STOP RESET pad to clear display Operating Preprogrammed Pads From the factory this oven can of store up to 10 preprogrammed cooking sequences in memory To heat using a preprogrammed sequence press a numbered pad Oven starts to heat automatically Example Heat using the third cooking sequence 1 Open oven door place food in oven and close oven door e Display shows READY If pad is not pressed in 60 seconds open and close oven door again 2 Press 3 pad e Oven operates and time counts down e Display shows cooking time POWER COOK LEVEL Display shows POWER only when microwave energy is present If power level other than 100 percent power was programmed display shows COOK LEVEL and power level If additional cooking time is required press preprogrammed pads before or after cooking cycle ends 3 Oven stops cooking and oven signal sounds when cooking timing elapses Preprogrammed Times and Cook Level All preprogrammed pads arrive set2. at full power Pads Times Pads Times 1 10 sec 6 1 30 min 2 20 sec 7 2 min 3 30 sec 8 3 min 4 45 sec 9 4 min 5 1 min 0 5 min Double Pad Programs The oven control can be changed to store up to 100 cooking programs See the User s Options section of this manual to change oven control To start a double pad cooking program press 2 memory pads For example press pad 0 and pad 3 to start a cooking program Using X2 Pad X2 pad increases the cooking time when cooking more than one item at a time is necessary The amount of added time when the X2 pad is pressed is a percent of the original preprogrammed cooking time The percent can be set from 10 to 100 with the default at 80 The percent of the time added can be changed for individual cooking programs Press X2 pad before pressing memory pad For example press X2 pad and then memory pad 3 Pad 3 normally cooks for 30 seconds When the X2 pad is pressed before memory pad 3 54 seconds displays because it added 24 seconds 80 of 30 sec 24 sec Manual Time Entry Manual Time Entry feature allows the operator to enter time and power levels and heat without changing the preprogrammed pads Example Heat for 30 seconds at 80 power 1 Open oven door place food in oven and close door e Display shows READY Fan and light operate e f pad is not pressed in 60 seconds open and close oven door again 2 Press T
3. 0 percent power RS5320013 Rev 0 4 Press 3 and 0 to enter desired cooking time 5 Press POWER LEVEL pad to change power level e Display shows COOK LEVEL and current power level if other than 100 percent power 6 Press 8 pad to enter desired power level 7 Press TIME ENTRY pad e Display briefly shows P 03 indicating programming pad 3 stage 2 Then cook time and power level for stage show in display e Repeat steps 5 8 to create additional stages 8 Press START pad to save new cooking time and power level in oven memory 9 Press STOP RESET pad or close oven door to exit programming mode X2 Quantity Feature This feature allows the user to change the amount of time added when the X2 pad and then the programmed pad is pressed Based on the original time the X2 pad can add from 10 100 of additional cooking time The default is 80 Example change cooking factor to 50 for third cooking sequence 1 Open oven door e f door is closed or RESET pad is pressed before finishing programming sequence oven exits programming mode 2 Press and hold pad 1 for approximately 5 seconds e After 5 seconds signal sounds Display shows P 3 Press 3 pad to select the cooking program 4 Press 5 pad to change cooking factor e Display shows CF 05 5 Press START pad to save changes 6 Press STOP RESET pad or close oven door to exit programming mode Double Pad Programs The oven control can be c
4. Control Panel Features TIME STOP ENTRY POWER START ar x2 as es TIME ENTRY TIME ENTRY pad is used to enter cooking time for either manual entry or programming Cooking time ranges from 1 second 00 01 to a total of 60 minutes 60 00 over four stages If more than 60 minutes of total microwave cooking time is required open door and inspect food before beginning new cooking cycle xe X2 pad increases the cooking time when cooking more than one item at a time is necessary The amount of added time when the X2 pad is pressed is a percent of the original preprogrammed cooking time The percent can be set from 10 to 100 with the default at 80 The percent of the time added can be changed for individual cooking sequences ajo Numbered pads begin cooking programs or enter times and power levels for Manual Time Entry cooking POWER LEVEL pad is used to set microwave power level When cooking the power level can be decreased for foods that require slower more even cooking Microwave power levels range from 0 to 100 in 10 increments If cooking time is set and START pad pressed oven cooks at 100 power When programming to reset power level to 100 press POWER LEVEL pad START START pad begins Manual Time Entry cooking or restarts an interrupted cooking cycle When programming use to save time and power level and to advance to next user option STOP RESET STOP RESET pad exits program
5. IME ENTRY pad Display shows 0000 and READY 3 Press 3 and 0 pad to enter cooking time 4 Press POWER LEVEL pad to change power level e Display shows COOK LEVEL and current power level if other than 100 percent power 5 Press 8 pad to enter desired power level 6 Press START pad e Oven operates and time counts down e Display shows cooking time POWER COOK LEVEL e Display shows POWER only when microwave energy is present e If power level other than 100 percent power was programmed display shows COOK LEVEL and power level Display counts down cooking time 7 Oven stops cooking and oven signal sounds when cooking timing elapses 15 RS5320013 Rev 0 Programming Instructions Memory Pads From the factory this oven can of store up to 10 cooking programs Follow instructions below to program cooking times and power levels for customized cooking Example Program third cooking sequence to heat for 30 seconds at 80 power 1 Open oven door e Display shows READY e f door is closed or RESET pad is pressed before finishing programming sequence oven exits programming mode 2 Press and hold pad 1 for approximately 5 seconds After 5 seconds signal sounds Display shows P 0 3 Press 3 pad to select memory pad e Display shows cooking time COOK LEVEL and power level if other than 100 percent power Press 3 and 0 pad to enter desired cooking time
6. Press POWER LEVEL pad to change power level e Display shows COOK LEVEL and current power level if other than 100 percent power Press 8 pad to enter desired power level Press START pad to save new cooking time and power level in oven memory e Display shows P 0 e Repeat step 3 8 to program additional pads 8 Press STOP RESET pad or close oven door to exit programming mode ak NOD Double Pad Programs The oven control can be changed to store up to 100 cooking programs See the User s Options section of this manual to change oven control To create a double pad program follow the instructions above except for a change to step 3 When entering the cooking program number press 2 memory pads For example press pads 0 and pad 3 to create a new cooking program Multiple Cooking Stages Follow instructions below to program oven to perform four consecutive cooking cycles without interruption Example Program third cooking sequence to heat for 30 seconds at 80 power 40 seconds at 50 power and 10 seconds at 100 power 1 Open oven door e Display shows READY e f door is closed or RESET pad is pressed before finishing programming sequence oven exits programming mode 2 Press pad 1 for approximately 5 seconds After 5 seconds signal sounds Display shows P 0 3 Press 3 pad to select memory pad e Display shows cooking time COOK LEVEL and power level if other than 10
7. al Time Entry feature allows the operator to heat without changing the preprogrammed pads Time must be entered and power can be set before cooking START pad must be pressed to begin cooking Cooking Displays READY shows when oven control will accept entries E READY POWER COOK LEVEL 25 20 shows cooking time When more than one cooking stage is programmed total time for all stages displays POWER Shows when microwave energy is generated COOK LEVEL shows when oven is operating 8 indicates the microwave power level used If number does not show oven is cooking at 100 power IE J L RS5320013 Rev 0 Programming Displays This display indicates oven is in programming mode and ready to program a numbered pad s F This display indicates oven is set to double pad entry and 2 pads must be pressed to enter a program See Programming section of manual for programming procedure or User Options to change from single or double pad entry dr F This display shows briefly when programming more than one stage It indicates programming mode for pad 02 The smaller 1 indicates stage 1 is being programmed co This display indicates programming user options mode See User Options section of manual for programming procedure CPOE This display indicates cooking factor of 80 when X2 pad is pressed
8. hanged to store up to 100 cooking programs See the User s Options section of this manual to change oven control To change the quantity for a double pad program follow the instructions above except for a change to step 3 When entering the cooking program number press 2 memory pads For example press pads 0 and pad 3 to create anew cooking program After the program is saved press pad 0 and pad 3 to start a cooking program Programming Instructions User Options Follow the instructions below to customized the microwave oven s operation End of cycle signal maximum cooking time and other options can be changed to meeting your cooking needs Example Change setting to single digit pad operation Press 9 pad See table for options e Displays shows OP 91 e OP represents optional program mode first number represents option number and second number represents functions currently selected for 1 Open oven door lf door is closed or RESET pad is pressed before 5 finishing programming sequence oven exits programming mode 2 Press and hold pad 2 for approximately 5 seconds e After 5 seconds signal sounds Display shows 6 OP option 4 Press 9 pad repeatedly to change setting Press START pad to save changes e Repeat steps 3 5 to change additional options e Changes appear after door is closed or STOP RESET is pressed Press STOP RESET pad or close oven door to exit prog
9. ming mode and stop cooking during cooking cycle MICRO DEFR WARM MEDHI POWER HOLD E HHE oe recy Display Some items in display can be seen but will not glow Stages This oven can be programmed to run 4 cooking sequences consecutively Each sequence is called a stage For example the first cycle could be programmed to defrost at 60 power the second to defrost at 30 power the third to heat at 100 power and the fourth to hold warm at 10 power Total time for all cooking stages counts down User Options User Options allow the user to program the oven to perform in a way convenient to the user The beeps maximum cooking time and number of preprogrammed cooking sequences can be changed 13 RS5320013 Rev 0 Displays Cooking Methods Memory Pads This oven can of store either 10 or 100 cooking programs in memory Single Pad Cooking From the factory it is programmed to store 10 cooking programs Each pad begins a cooking program Double Pad Cooking The oven control can be changed to store up to 100 cooking programs To set the control to 100 cooking programs see the User s Options section of this manual To heat when the oven is set for 100 programs press 2 memory pads For example to start the first program press pad 0 then pad 1 To use the second program press pad 0 then pad 2 After the pads are pressed the oven starts automatically and time counts down Manual Time Entry Manu
10. ramming mode Numbered Pads Display Options Factory Settings in Bold 1 OP 10 3 second continuous beep End of Cycle Beep OP 11 Continuous beep until door is opened OP 12 5 beeps bursts until door is opened 2 OP 20 Eliminates beep Speaker Volume OP 21 Sets volume to low OP 22 Sets volume to medium OP 23 Sets volume to high 3 OP 30 Prevents beep when pad is pressed Key Beep OP 31 Allows beep when pad is pressed 4 OP 40 15 seconds after oven door is opened keyboard disabled Keyboard Enable OP 41 30 seconds after oven door is opened keyboard disabled Window OP 42 1 minute after oven door is opened keyboard disabled OP 43 2 minutes after oven door is opened keyboard disabled 5 OP 50 Prevents adding heating time while oven is heating Add Time during OP 51 Allows heating time to be changed while oven is heating Heating when a memory pad is pressed 6 OP 60 Allows oven to resume heating time countdown after door is Reset Door Open opened during cycle OP 61 Cancels heating time countdown after door is opened during cycle 7 OP 70 Allows 60 minutes of heating time Maximum Heating OP 71 Allows 10 minutes of heating time Time 8 OP 80 Allows use of preprogrammed pads only Manual Operation OP 81 Allows use of manual time entry and preprogrammed pads 9 OP 90 Allows 10 0 9 preprogrammed pads Double Digit OP 91 Allows 100 00 99 preprogrammed pads Operation 17 RS5320013 Rev 0
Download Pdf Manuals
Related Search
DEC/HDC/UC/UHDC